Regency CC40LE-NG, CC40LE-LP, CC40RE-NG, CC40RE-LP, City Series Owners & Installation Manual

...

Download

Page 1

City Series

Zero Clearance Direct Vent Gas Fireplace

Owners &

Installation Manual

www.regency-re.com

STYLE MODEL Left Corner CC40LE-NG / CC40LE-LP Right Corner CC40RE-NG / CC40RE-LP

Warning Fire or explosion Hazard

failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch: do not use any phone in your building.

Leave the building immediately.

• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's

instructions.

• If you cannot reach you gas supplier, call the ﬁre department.

- Installation and service must be performed by a qualiﬁed installer, service agency or the gas supplier.

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

919-740a

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

04.26.17

Page 2

To the New Owner:

Congratulations! You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The City Series are hand crafted appliances and have been designed to provide you with all the warmth and charm of a wood ﬁreplace at the ﬂick of a switch. The CC40LE /CC40RE City Series have been approved by Intertek for both safety and efﬁciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible fore use with other gases, unless a certiﬁed kit is used.

2 | City Series

Page 3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency® product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following standards: VENTED GAS DECORATIVE FIREPLACE CAN/CGA-2.17-M91, and ANSI Z21.50-2014 • CSA 2.22-2014 HIGH ALTITUDES CAN/CGA 2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This Regency® mobile/manufactured home listed appliance comes factory equipped with four 1/4" diameter holes located near each corner of the base. Fasten the ﬁreplace in place using screw, inserted through the holes.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local codes. See the "Wiring Diagram" section.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured home (U.S.A only) or mobile home, where not prohibited by local codes.

. and GAS-FIRED APPLIANCES FOR USE AT

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Ensure that structural members are not cut or weakened during installation.

City Series | 3

Page 4

table of contents

Copy of Safety Decal .....................................................5

Installation................................................................9-60

Important Message ......................................................9

Before You Start .............................................................9

General Safety Information ..........................................10

Installation Checklist ....................................................10

Heatwave Duct System ...............................................10

Locating Your Gas Fireplace ........................................11

Unit Assembly Prior to Installation ...............................11

Clearances CC40LE/CC40RE .....................................13

Clearances CC40LE/CC40RE .....................................14

Clearances CC40LE/CC40RE .....................................15

Mantel Clearances CC40LE/CC40RE .........................16

Framing Dimensions CC40LE (Left Corner) ................17

Framing Dimensions CC40RE (Right corner) .............18

Wall Board/Drywall Installation CC40LE/CC40RE ......19

Framing and Finishing Inset Installations CC40LE/

CC40RE ......................................................................20

Optional Framing Kit Installation CC40LE/CC40RE ....21

Building additional framing off of the framing kit ..........24

Guidelines for installing a TV / artwork |above the unit 2 5

TV recessed into wall ..................................................25

Exterior Vent Termination Locations ............................26

4” x 6-5/8” Rigid Pipe Cross Reference Chart .............27

Wall Mount On / Off Switch and Battery Holder Installa-

tion ...............................................................................29

Required for all installations .......................................29

Vent Restrictor Position ...............................................30

Horizontal Terminations ...............................................31

Flex Vent 4" x 6-7/8" ....................................................31

Venting Introduction .....................................................32

Venting Arrangement for Horizontal Terminations .......32

Horizontal Terminations ...............................................33

Rigid Pipe 4" x 6-5/8" ...................................................33

Horizontal Terminations ...............................................34

Rigid Pipe 4" x 6-5/8" ...................................................34

Horizontal Venting with Two (2) 90o Elbows .................34

Horizontal Venting with Three (3) 90o Elbows ..............34

Vertical terminations

Rigid Pipe 4" x 6-5/8" ...................................................35

Venting Arrangement for Vertical Terminations ............36

Vertical Terminations Rigid Pipe 4" x 6-5/8" ...............37

Unit Installation with Horizontal Termination ...............38

4" x 6-5/8" venting .......................................................38

Unit Installation with Horizontal Termination ...............39

Dura-Vent

Horizontal terminations ................................................40

Dura-Vent Vertical Termination ....................................41

4" x 6-5/8" venting .......................................................41

Vertical Termination 4" x 6-7/8" venting .....................42

Vertical ﬂue extension kit (part #946-756) ...................43

Ceiling Firestop / ﬁrestop spacer (part #946-757) .......43

High Elevation ..............................................................44

Gas Line Installation ....................................................44

Pilot Adjustment ...........................................................44

Gas Pipe Pressure Testing ..........................................44

885 S.I.T. Valve Description .........................................44

Wiring Diagrams ..........................................................45

Inner glass panel (ﬁrebox glass) Installation / removal 46 Outer safety glass panel (barrier glass) Installation /

removal ........................................................................48

Outer safety glass panel (barrier glass) Installation / re-

moval ...........................................................................49

LP Conversion Instructions ..........................................50

CC40LE/CC40RE Painted panel installation ...............52

Inner Panels - CC40LE/CC40RE.................................52

Outer Panels - CC40LE/CC40RE ................................52

CC40LE/CC40RE glass panel installation ...................53

CC40LE/CC40RE enamel panel installation ...............55

Burner and Firebox media options ..............................57

Optional driftwood Log set Installation .........................58

CC40LE/CC40RE - Removable drywall guides ...........60

Operating instructions..........................................61-63

First Fire ......................................................................61

Normal Operating Sounds of Gas Appliances .............61

Aeration Adjustment ....................................................61

Lighting Procedure ......................................................62

Shutdown Procedure ...................................................62

Copy of the Lighting Plate Instructions ........................63

Maintenance...........................................................60-62

Maintenance Instructions ............................................64

Log Replacement ........................................................64

Glass Gasket ...............................................................64

Glass ...........................................................................64

Glass replacement .......................................................64

Bulb Replacement .......................................................65

Valve Replacement ......................................................66

Parts List................................................................67-70

CC40LE main assembly ..............................................67

CC40RE main assembly .............................................69

Warranty............................................................................72-75

4 | City Series

Page 5

This is a copy of the label that accompanies Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located on the front inside base of the unit, visible when the outer front panel is removed.

NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

Copy of Safety Decal

safety decal

For the State of Massachusetts, installation and repair must be done by a plumber or gasﬁtter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, ﬂexible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed.

City Series | 5

Page 6

requirements

MA Code - CO Detector

(for the State of Massachusetts only)

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

6 | City Series

Page 7

CC40LE (Left Corner) dimensions

475mm

616mm

102mm

1203mm

48"

1219mm

dimensions

587mm

183mm

291mm

171mm

448mm

200mm

10 "

382mm

261mm

873mm

375mm

Note: Height Dimension may vary depending on the height of the leveling legs.

Dimensions will appear as (inches)" / (metric)mm throughout this manual. The inches are rounded to the nearest 1/16" when converted, when greater accuracy is required, use the metric dimensions.

1108mm

1089mm

642mm

842mm

943mm

Note: These units are non-load bearing.

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

City Series | 7

Page 8

dimensions

CC40RE (Right Corner) dimensions

587mm

1203mm

616mm

183mm

291mm

102mm

48"

1219mm

1108mm

171mm

642mm

842mm

943mm

15 "

200mm

382mm

261mm

475mm

17 5/8"

[448mm]

873mm

Note: Height Dimension may vary depending on the height of the leveling legs.

Dimensions will appear as (inches)" / (metric)mm throughout this manual. The inches are rounded to the nearest 1/16" when converted, when greater accuracy is required, use the metric dimensions.

1089mm

Note: These units are non-load bearing.

8 | City Series

375mm

Page 9

installation

Important Message

SAVE THESE INSTRUCTIONS

City Series Direct Vent Fireplaces must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁrst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this ﬁreplace is installed in compliance with manufacturer's instructions and all applicable codes.

Before You Start

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:

INSTALLATION AND REPAIR SHOULD BE DONE BY AN AUTHORIZED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN AND OTHERS MAY BE SUSCEPTIBLE TO ACCIDENTAL CONTACT BURNS. A PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL IN THE HOUSE. TO RESTRICT ACCESS TO A FIREPLACE OR STOVE, INSTALL AN ADJUSTABLE SAFETY GATE TO KEEP TODDLERS, YOUNG CHILDREN AND OTHER AT RISK INDIVIDUALS OUT OF THE ROOM AND AWAY FROM HOT SURFACES.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

A BARRIER DESIGNED TO REDUCE THE RISK OF BURNS FROM THE HOT VIEWING GLASS IS PROVIDED WITH THIS APPLIANCE AND SHALL BE INSTALLED FOR THE PROTECTION OF CHILDREN AND OTHER AT-RISK INDIVIDUALS

ANY SAFETY SCREEN, GUARD, OR BARRIER REMOVED FOR SERVICING THE APPLIANCE, MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.

WE RECOMMEND REMOVING THE GLASS WITH THE GLASS VACUUM HOLDERS SUPPLIED BY THE MANUFACTURER. LOWER THE GLASS TO REST IN A SAFE PLACE. THIS IS TO PREVENT DAMAGE TO THE GLASS EDGES. EXTRA CARE MUST BE TAKEN WHEN REMOVING/INSTALLING THE GLASS. BREAKAGE OR DAMAGE TO THE EDGE OF THE GLASS WHICH OCCURS AS A RESULT OF CARELESS HANDLING WILL NOT BE COVERED UNDER WARRANTY.

City Series | 9

IF THE BARRIER BECOMES DAMAGED, THE BARRIER SHALL BE REPLACED WITH THE MANUFACTURER'S BARRIER FOR THIS APPLIANCE.

Page 10

installation

General Safety Information

1. The appliance installation must conform with

local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2. See general construction and assembly

instructions. The appliance and vent should be enclosed.

3. This appliance must be connected to the

speciﬁed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is ﬁtted as per Venting instructions.

4. Inspect the venting system annually for blockage

and any signs of deterioration.

5. Venting terminals shall not be recessed into a

wall or siding.

6. Any safety glass removed for servicing must

be replaced prior to operating the appliance.

7. To prevent injury, do not allow anyone who is

unfamiliar with the operation to use the ﬁreplace.

8. Wear gloves and safety glasses for protection

while doing required maintenance.

9. Be aware of electrical wiring locations in walls

and ceilings when cutting holes for termination.

10. Under no circumstances should this appliance

be modiﬁed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

11. Installation and any repairs to this appliance

should be done by a qualiﬁed service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

12. Do not slam shut or strike the glass door.

13. Under no circumstances should any solid fuels

(wood, paper, cardboard, coal, etc.) be used in this appliance.

14. The appliance area must be kept clear and

free of combustible materials, (gases and other ﬂammable vapours and liquids).

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Installation Checklist

1. Locate appliance. Refer to the following sections:

a) Locating Your Fireplace b) Clearances c) Combustible Mantel Clearances d) Framing & Finishing e) Venting. See the "Venting Introduction" to

"Venting Arrangements" sections.

2. Assemble Standoffs. Refer to the "Unit Assembly Prior to Installation" section. (NOTE: must be done before installing unit into ﬁreplace.)

3. Install vent. See the "Horizontal Installations"

to "Installation Procedures" sections.

4. Install 4 AA batteries into receiver battery box. Connect receiver to wiring marked receiver, this will enable operation of the appliance manually when position in "ON" position.

Note: The wire harness (marked receiver) is

located near the gas valve and will need to be routed to the exterior of the ﬁreplace from either the left or right hand side of the appliance prior ﬁnishing.

5. Supply 120 volt power to appliance. This

will be required to operate lights and highly recommended to operate gas valve. AA Batteries serve as back up only if 120 volt power is lost.

6. Make gas connections. Test the pilot. Must be as

per diagram. Refer to the "Gas Line Installation" & "Pilot Adjustment" sections.

7. Install standard and optional features. Refer

to the following sections where applicable:

a. Safety Glass b. Firebox (inner) glass c. Log Set d. Fireglass e. Ceramic stones or other approved media f. Painted, enamel or glass panels (panels

required) g. Optional Framing Kit h. Heatwave Kit

8. Plug 3 prong plug for the lights into the

receptacle. The 3 prong plug will be located near the gas valve on the appliance.

9. Final check.

Before leaving this unit with the customer, the installer must ensure that the appliance is ﬁring correctly and operation fully explained to customer.

This includes:

1. Clocking the appliance to ensure the correct ﬁring rate (rate noted on label 28,500 Btu/h NG/ LP) after burning appliance for 15 minutes.

2. If required, adjusting the primary air to ensure that the ﬂame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

Heatwave Duct System Optional kit

The HeatWave Air Duct Kit increases the effectiveness of your ﬁreplace by dispersing warm air from the ﬁreplace to remote locations in the same room or other rooms in your home.

Up to two kits may be installed on the ﬁreplace.

Please Note: One adaptor kit #656-995 must be used with each 946-556.

The HeatWave Duct Kit has different clearance and framing requirements, check the HeatWave manual for details.

10 | City Series

Page 11

installation

Locating Your Gas Fireplace

1. When selecting a location for your ﬁreplace, ensure that the clearances are met.

2. The appliance must be installed on a ﬂat, solid, continuous surface For example a wood, metal or concrete ﬂoor or in a raised (on the wall) application. The appliance must be installed on a metal or wood panel extending the full width and depth of the appliance.

3. The CC40LE/CC40RE Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A and B. See Diagram 1.

Unit Assembly Prior to Installation

Before you start

The CC40LE/CC40RE has 4 standoffs, 2 on one side and 2 at the back that need assembly before installation.

Side and back standoff assembly CC40LE/CC40RE

The standoffs are shipped in a ﬂat position and must be folded into shape and attached.

Take each standoff off the unit by removing one screw and bend into the correct shape. Slot the 2 tabs of the stand off into the slots in the unit and attach the other end with one screw.

Standoﬀ locations

CC40LE/CC40RE

Diagram 1

A) Corner Left B) Corner Right

4. For bedroom installations, check with local codes before installation. This appliance is offered with a remote control.

5. The CC40LE/CC40RE Direct Vent Gas Fireplace is approved for alcove installations, see "Clearances" section for details.

6. We recommend that you plan your installation on paper using exact measurements for clearances and ﬂoor protection before actually installing this appliance. Have an authorized inspector, dealer, or installer review your plans before installation.

Note: For vent terminations refer to "Exterior

Vent Termination Locations" section.

Back standoff assembly CC40LE/ CC40RE

Take each standoff off the unit by removing one screw. Bend into the correct shape (see above). Slot the 2 tabs of the stand off into the slots in the unit and attach the other end with one screw.

CC40LE/CC40RE

City Series | 11

Page 12

installation

Top nailing strip

Nailing strips CC40LE/CC40RE

Nailing strips are shipped folded ﬂat against the unit. Fold nailing strips out 90º before installing unit. Secure nailing strips to framing using wood or metal screws.

Top Nailing strip CC40LE/CC40RE

Nailing strip is shipped with the appliance and will need to be attached. Note that the nailing strips are not required if using the optional chase or extended framing kit and may be recycled.

1. Secure nailing strip to appliance with 2 screws.

2. Secure nailing strips to framing using wood or metal screws.

Side nailing strip CC40LE

Top nailing strip

Side nailing strip CC40RE

Levelling bolts

There are four levelling bolts - two on each side that can be adjusted if required.

Access panel removal

The front access panel may be removed for ease of hooking up gas and electrical. Once complete ensure that the access panel is reinstalled prior to any ﬁnishing. The CC40LE/CC40RE has 4 screws to remove access cover. See locations in diagram to the right.

Leveling bolts

12 | City Series

Access panel screws

Page 13

installation

Clearances CC40LE/CC40RE

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ﬁres is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this ﬁreplace and vent system be installed only in accordance with these instructions.

Note: CC40LE shown in illustration. Clearances will be the same for the CC40RE.

Clearance: single sided Dimension Measured From:

A: Mantel Height (min.)

B: Opening Height

C: From Floor

D: Sidewall (on one side)

E: Mantel Depth (Max.)

F: Alcove Depth

G: Convection Air Outlet

H: Convection Air Outlet Opening Offset

I: Chase Enclosure (Min.)

Hearth

** See mantel clearances chart in this manual.

** Top of Fireplace Opening

15-1/16" (382mm) Bottom/Top of Fireplace Opening

Min. 0" Bottom of Fireplace Opening

Min. 36" (914mm) Side of Fireplace Opening

** Front of Fireplace Opening

Min. 36" (914mm) Front of Fireplace Opening

* Top of Enclosure

0-3" (76mm) Max. offset from top of chase enclosure

63" (1600mm) From Base of Unit

0" No hearth required

Flue Clearances to Combustibles

Horizontal - Top 3" Horizontal - Side 2" Horizontal - Bottom 2" Vertical 2"

Passing through wall/ floor/ceiling - when

1-1/2"

ﬁrestop is used.

*A minimum of 120 square

inches of open area, not lower than 3" from top of enclosure, required for all installations

The HeatWave Duct Kit has different clearance and framing requirements, check the HeatWave manual

for details.

Caution Requirements

The top, back and sides of the ﬁreplace are deﬁned by

standoffs. The metal ends of the standoff may NOT be

recessed into combustible construction.

CC40 UNIT

Top View

Alcove

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this ﬁreplace and vent

system be installed only in accordance with these instructions.

Fire hazard is an extreme risk

WARNING

City Series | 13

Page 14

installation

top op

Clearances CC40LE/CC40RE

CC40LE shown

Low framing with ven

Low framing with vents in front/sides or top

CC40LE shown

14 | City Series

Floor to ceiling with

Floor to ceiling with top opening

Page 15

Clearances CC40LE/CC40RE

installation

CC40LE shown

Chase enclosed

Full framing with low vents in front or sides

CC40LE shown

City Series | 15

Full framing with vents in front or sides

Page 16

installation

Mantel Clearances CC40LE/CC40RE

Combustible mantel clearances from top of front facing are shown in the diagram on the right.

12" (305mm)

212 6 4810

Drywall, wood, wood panel, etc.

Combustible Material

Wood Stud

(On Edge)

Standof

”

To Bottom of Fireplace Lip

15-1/16”

2”

Top of Fireplace Opening

16 | City Series

Page 17

Framing Dimensions CC40LE (Left Corner)

NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.

installation

Framing Dimensions

A Framing Height 37-3/8” (949mm) B Framing Width 48-1/4" (1226mm) C Framing Depth 19" (483mm) D Unit Base to Top Enclosure (Min.) 63"(1600mm) G Vent Centerline Height 56-1/4" (1429mm)

NOTE: Unit cannot be load-bearing. All ﬁnishing materials must be supported by the framing.

Description CC40LE

Note: A combined minimum of 120 square inches of open area is required for the convection air outlet to cool the enclosure. Ensure clearances for Convection Air Outlets are met. See clearances CC40LE/CC40RE (single sided) in this manual as there are different methods as to how this can be achieved.

Note: This appliance must be installed on a level and solid surface such as a plywood ﬂoor which must be the full width and depth of the appliance.

City Series | 17

Page 18

installation

Framing Dimensions CC40RE (Right corner)

NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.

Framing Dimensions

A Framing Height 37-3/8” (949mm) B Framing Width 48-1/4" (1226mm) C Framing Depth 19" (483mm) D Unit Base to Top Enclosure (Min.) 63"(1600mm) G Vent Centerline Height 56-1/4" (1429mm)

NOTE: Unit cannot be load-bearing. All ﬁnishing materials must be supported by the framing.

Description CC40RE

Note: A combined minimum of 120 square inches of open area is required for the convection air outlet to cool the enclosure. Ensure clearances for Convection Air Outlets are met. See clearances CC40RE (in this manual) as there are different methods as to how this can be achieved.

Note: This appliance must be installed on a level and solid surface such as a plywood ﬂoor which must be the full width and depth of the appliance.

18 | City Series

Page 19

installation

Wall Board/Drywall Installation CC40LE/CC40RE

WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as speciﬁed.

Finishing Instructions It is important to follow the framing and ﬁnishing instructions to ensure proper placement of ﬁreplace into the surrounding framing/ﬁnishing materials. Wall board materials 1/2 in. thick are speciﬁed in this installation manual to properly align with the optional ﬁnishing methods offered with this appliance. The

CC40LE/CC40RE may be ﬁnished to the appliance opening with 1/2 inch thick drywall.

• Ensure that the back and side clearances are maintained.

WARNING! Risk of Fire! Maintain speciﬁed air space clearances to combustibles. Inadequate air space could cause overheating and ﬁre.

DO NOT use screws more than 3/4 inch in length on the lower access cover panel. Longer screws may penetrate gas line or damage valve or electrical

components. Note: It is acceptable to use a high temperature silicone sealant to adhere drywall to lower access cover panel.

The appliance is designed to be used with 1/2 in. wall sheathing materials such as drywall, plywood, wood composites, or non-combustible materials. Thicker materials may be used. Refer to facing and ﬁnishing details in this manual.

Facing Material

• Facing and/or ﬁnishing materials must never overhang into the glass opening.

• Facing materials may be combustible or non-combustible

WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as speciﬁed in this manual. Overlapping materials could ignite and will interfere with proper operation.

PAINTING

If desired ﬁnishing includes a painted wall, 100% acrylic latex, oil-based or standard acrylic paints may be used. Follow paint manufacturer’s instructions for paint and primer application.

City Series | 19

Page 20

installation

Framing and Finishing Inset Installations CC40LE/CC40RE

1. Frame in the enclosure for the unit with framing material

Note: When constructing the framed opening ensure there is sufﬁcient access to install the gas lines,electrical. Also the wiring harness must be wall mounted using the receptacle provided with the appliance. The wiring harness will be located on the right hand side of the appliance if facing the unit from the front. This must be done prior to any ﬁnishing.

2. For exterior walls, insulate the enclosure to the same degree as the rest of the house, apply vapour barrier and drywall, as per local installation codes. (Do not insulate the ﬁreplace itself.)

WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems including, but not limited to: excessive condensation on glass doors, poor ﬂame package, carbon, blue ﬂames etc. These are not product related issues.

3. The unit does not have to be completely enclosed in a chase. You must

maintain clearances from the vent to combustible materials: See "Clearances" section. Combustible materials can be laid against the side and back standoffs and the stove base.

4. Combustible material (drywall,wood,wood panels, etc.) may be brought

up to this appliance (top,bottom and sides)

5. Ensure that the material being used does not encroach anywhere in the

area of the glass. This would cause dangerous operating conditions.

6. This appliance comes with a 1/2" lip at top, sides and bottom to hide the

ends of the drywall. The 1/2" side and bottom, front and bottom side lips supplied with the appliance can alternatively be removed and replaced with J Style Trim or Metal Corner Bead purchased at your local hardware store to cover cut/exposed edges of the combustible facing material or any other ﬁnishing materials being used. Six (6) screws secure the bottom front lip. Two (2) secure the bottom side lips and 2 secure the side if deciding to remove these. These will be hidden so the outer panels (if installed) will need to be removed to access the screws. See outer panel removal in this manual.

7. This appliance can also be recessed (using combustible materials) with

a hearth in front of the appliance. This can also extend to the top. See below for details.

8. The wall behind the unit must be closed off.

**Combustible material may extend a minimum of 1/2" and to a maximum of 2-1/2" from the Front top and open side faces of the appliance. If 2-1/2" is insufﬁcient non combustible material may be used instead of combustible to extend the ﬁnished material further out or alternatively be staggered if using combustible materials. See mantle clearance chart for details. The base and closed side have no limit when it comes to how far the combustible material may extend out from the appliance.

Note: an offset screwdriver is provided with the appliance for ease of removal/ installation.

20 | City Series

Page 21

Optional Framing Kit Installation CC40LE/CC40RE

CC40LE/CC40RE FRAMING KIT INSTALLATION

CITY SERIES

This framing kit is for the CC40LE/CC40RE. The parts are adaptable so the same kit can be installed on either the right or left side units.

NOTE: CC40RE SHOWN IN DIAGRAMS

Installation is the same for CC40LE, please note that images will appear ﬂ ipped.

A 656-391

1. This framing kit requires the installation of two studs at locations shown below. Be sure to install studs and walls to enclose chase (see Unit Manual) prior to moving the unit into position.

installation

Shown for CC40RE

Stud

18"

B 656-392

2x C 656-393

D 656-396

E 656-394

F 656-398

G 656-397

H 656-395

J 656-399

K 656-400

Unit nailing strips are not required and can be recycled when using the framing kit.

Remove nailing ﬂ anges

49 3/4"

Stud

2. Begin with the unit away from the wall. Install part A to the back of the unit using holes next to appropriate shape (diamond or square depending on which unit you have) using the diagrams below. Attach to the back of the unit using 2 screws in locations shown below.

CC40RE

Holes next to squares

Measured from wall to stud center

CC40LE

Holes next to diamonds

City Series | 21

NOTE: CC40LE use holes corresponding with diamond shape. CC40RE use holes corresponding with square shape.

Page 22

installation

CITY SERIES

3. Install B to the side of the unit, use the holes corresponding with the

appropriate shape (diamond or square depending on which unit you have) using the diagrams below. Attach B to the side of the unit and install 2 screws in locations shown below.

CC40RE

Holes next to squares

4. Install 2 x part C's onto par ts A & B respectively, identify the holes to

be used, attach to the unit with 2 screws each.

CC40LE

Holes next to diamonds

5. Slide unit against wall and line up part C's with studs in the wall. Attach both part C's to studs with at least two screws each; one at the top, and one near the unit (as seen below).

6. Install venting before proceeding further with framing kit construction. Refer to manual for venting instructions.

7. Identify D, attach to back corner C with 2 screws as shown below.

Studs

Part D Proﬁ le

8. Identify E (see diagram below), attach E to front corner C with 2 screws as shown below.

Part E Proﬁ le

22 | City Series

Page 23

installation

CITY SERIES

9. Identify F and attach to both E and D with 2 screws on each side.

10. Identify G and attach to back corner C and front corner F with 2

screws on each side.

12. Identify J (diagonal support) and attach to back corners C and front

corner F with 2 screws on each side.

13. Attach K (center support) to E and H with 2 screws each.

11. Identify H and attach to both front corners C and F with 2 screws on each side.

City Series | 23

Page 24

installation

BUILDING FRAMING OFF OF THE KIT

CITY SERIES

Building additional framing off of the framing kit

This framing kit is designed as a base in which to build additional framing. Studs can be afﬁ xed to all outer faces using the holes identiﬁ ed below. This will provide a stable surface that is ﬂ ush with the front of the ﬁ replace, ready for drywall or other ﬁ nishing material.

The framing must be strong enough to support the weight of all ﬁ nishing material and must not put any weight on the ﬁ replace.

Holes for ﬁ xing additional

framing to kit

Potential Wood Framing installs

24 | City Series

1/2” for drywall

Leave gap between framing and unit trim for nishing material

Page 25

Guidelines for installing a TV / ARTWORK above the unit

3.5”

MAX

Vertical 2x4

12.0” MIN

Horizontal 2x4

15.5” MIN

Airow

Zone

Do not

obstruct

installation

Note: All wiring should stay free and clear of the vent system to avoid damage due to heat. We recommend using a metal receptacle box and BX cable (120

volt wire protected by metal sheathing) if located directly in front of the vent

system. Ensure wiring is secured without any sag.

ZERO CLEARANCE TO TV: While most consumers prefer to centrally locate a wall mounted TV, the “Cool-Touch Wall Technology” means that the bottom edge of the TV can be installed ﬂush with the bottom edge of the ventilated

ﬁreplace chase opening.

The TV cannot be any lower than this ﬁnishing lip.

TV recessed into wall

The TV may be recessed into a wall as shown below. This can only recess into the chase opening a maximum of 3-1/2 inches and must be a minimum of 12 inches from the ﬁreplace lip to the ﬁrst stud. To achieve a maximum of 3-1/2" recess, the wall must be of a maximum of 2" as shown.

Airow

Zone

Do not

obstruct

15.5” MIN

Horizontal 2x4

12.0” MIN

Vertical 2x4

3.5”

MAX

Sample Install 1 Sample Install 2

3.5”

2.0”

12.0”

3.5”

MAX

20.0”

16.5”

3.5”

MAX

15.5”

2”

City Series | 25

Page 26

installation

Exterior Vent Termination Locations

Minimum Clearance Requirements

Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)

Clearance to window or door that may be opened 12"(30cm) 9" (23cm)

Clearance to permanently closed window * *

Vertical clearance to ventilated sofﬁt located above the terminal within a horizontal distance of 2 feet (61cm) from the center line of the terminal (check with the local code)

Clearance to unventilated sofﬁt 20"(51cm) 20"(51cm)

Clearance to outside corner: with AstroCap Termination Cap. 6"(15cm) 6"(15cm)

Clearance to outside corner: with all other approved Termination Caps. 14"(36cm) 14"(36cm)

Clearance to inside corner: with AstroCap Termination Cap 6"(15cm) 6"(12cm)

Clearance to inside corner: with all other approved Termination Caps. 12"(30cm)

Clearance to each side of center line extended above meter/regulator assembly 36"(90cm)

Clearance to service regulator vent outlet 36"(90cm) *

Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)

Clearance to a mechanical air supply inlet #3' (91cm) above if within 10' (3m) horizontally.

Clearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)

Clearance under veranda, porch, deck, or balcony 12"(30cm)

In accordance with current CSA B149.1, Natural Gas and Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code

┼

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂoor

Clearance in accordance with local installation codes and the requirements of the gas supplier

3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly

3 feet (91cm) above - if within 10 feet (3m) horizontally

Canada

18"(46cm) 18"(46cm)

12"(30cm)

13"(33cm)

72"(1.8m) 36"(90cm)

┼

‡

USA

26 | City Series

Page 27

installation

4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART

Components from different Manufacturers may not be mixed. Not all rigid pipe components are available directly from Regency. Note: The listed manufacturers may have other lengths not shown on this chart, which would also be approved.

4” x 6-5/8” Rigid Pipe Cross Reference Chart

Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.

* Olympia Ventis DV applicable for the following units only: B36XTE, B36XTCE, B41XTE, B41XTCE, P36, P36E

Description

6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6 VDV-0406

6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B VDVB-0406

7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A N/A

7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A N/A

9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A TC-4DL9 VDV-0409

9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A TC-4DL9B VDVB-0409

12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1 VDV-0412

12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B VDVB-0412

18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18 VDV-0418

18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B VDVB-0418

24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2 VDV-0424

24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B VDVB-0424

36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3 VDV-0436

36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B VDVCB-0436

48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4 VDV-0448

48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B VDVB-0448

60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A N/A

60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A N/A

Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT N/A

Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB N/A

Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A N/A

Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A N/A

Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A N/A

Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A N/A

Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 TC-4dLSI N/A

Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 TC-4dLSIB N/A

Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A N/A

Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A N/A

Simpson

Direct Vent Pro

Selkirk

Direct Temp™

American Metal Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

Olympia Ventis DV*

45º Elbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45 VDV-EL0445

45º Elbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B VDVB-EL0445

45º Elbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A N/A

45º Elbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A N/A

90º Elbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90 VDV-EL0445

90º Elbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B VDVB-EL0445

90º Elbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A N/A

90º Elbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A N/A

90º Starter Elbow, Swivel-Galvanized

Adaptor* N/A N/A N/A 4D90L N/A N/A VDV-UAA04

Ceiling Support N/A 4DT-CS 4DSP 4DFSP SV4SD TM4-RDS VDV-SCR04

Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TM4-SDS VDV-CSS04

Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM TM-SWS VDV-WS04

Offset Support46

Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM N/A VDV-WPT04

Wal

l Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF N/A N/A

Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF TM-4CS VDV-FS04

Tr im Plate-Black N/A 4DT-TP 4DFPB 4DcP SV4LA TM-4TP VDV-WTC04

N/A N/A N/A 4D90A N/A N/A N/A

DVA-ES - N/A

from FPI

4DT-OS N/A N/A SV4SU TM-SOS N/A

City Series | 27

Page 28

installation

Description

Attic Insulation Shield 12” 46DVA-IS

Attic Insulation Shield - Cold Climates 36”

Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK TM4-HTK VDV-KW04

Horizontal Termination Kit (B) 46DVA-KHA

Ver tical Termination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A N/A

High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT VDV-VCHW04

High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT N/A

Horizontal Square Termination Cap 46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT VDV-HC04

Ver tical Termination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 N/A N/A

Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC VDV-SC04

Adjustable Flashing 0/12-6/12 46DVA-F6 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FAVDV-F0406

Adjustable Flashing 6/12-12/12 46DVA-F12 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB VDV-SSO

Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS N/A

Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A N/A

Snorkel Termination 14” 46DVA-SNK14 N/A N/A N/A N/A TM-4ST14 N/A

Snorkel Termination 36” N/A N/A N/A N/A N/A TM-4ST36 N/A

Restrictor Disk N/A N/A N/A N/A N/A TM-4DS N/A

Extended Vertical Te rmination Cap N/A N/A N/A N/A N/A N/A N/A

Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6 N/A

Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7 N/A

Chimney Conversion Kit C (USA only)

Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR VDV-FS04

Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A N/A

Simpson

Direct Vent Pro

N/A@ FPI

N/A N/A 4DAIS12 N/A N/A TM-4AS N/A

(Changed Components)

46DVA-KCC N/A N/A N/A N/A TM-4CA8 N/A

Selkirk

Direct Temp™

N/A 4DAIS12 N/A SV4RSA N/A VDV-AIS04

4DT-HKB 4DHTK1 4DHTKB SV-HK TM4-HTK VDV-K04

American Metal Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

Olympia Ventis DV*

* Olympia Ventis DV applicable for the following units only: B36XTE, B36XTCE, B41XTE, B41XTCE, P36, P36E

FPI

946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal

510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal

640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap

946-206 Vinyl Siding Standoff for AstroCap

Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).

Offset Pipe Selection: Use this table to determine offset pipe lengths.

Pipe Length

(L)

0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com

6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com

9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com

12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com

24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com

36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com

48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination. Never allow the vent to run downward - this could cause high temperatures and may present a possible ﬁ re hazard.

4” x 6-5/8” Venting For speciﬁ c instructions on venting components - visit the

Run (X) Rise (Y)

manufacturers website listed below.

28 | City Series

Page 29

Wall Mount On / Off Switch and Battery Holder Installation

Required for all installations

IMPORTANT INSTALLATION NOTE:

The Battery Holder must be placed inside the supplied (Low Voltage) junction type wall box and installed into

the wall only.

DO NOT INSTALL WITHIN THE CONFINES OF THE FIREPLACE SWITCH MUST BE ACCESSIBLE

Battery Holder Installation

1. Install the low voltage junction box to the framing, at desired location within 10-1/2 ft. from replace.

2. Feed the 6 pin connector wiring harness through the opening at back of junction box. The wiring harness

is located near the gas valve and will need to be routed to the exterior of the replace from either the left

or right hand side prior to nishing.

3. Connect the 6 pin connector to the back of the Battery Holder.

4. Install the Battery Holder in the Low Voltage Junction box.

5. Install batteries only if 120 volt power will not be used. Batteries are only used if power is lost within the

home and serve as a secondary power source. Insert the 4 AA type batteries in the battery compartment

with the correct polarity.

6. Place the slider into the cover plate.

7. Put the Battery Holder switch in the “OFF” position, to allow correct lineup for slider switch.

8. Make sure the Battery Holder and cover plate words “ON” and “UP” are on the same side.

9. Align the slider with the switch on the Battery Holder and couple the switch into the slider.

10. Align the screw holes.

11. Using the two (2) screws provided secure the cover plate to the Battery Holder.

12. For coding instructions, see full details in this manual.

installation

Low Voltage Junction Box

Proame Battery Holder

Slider Switch

J-Box

Battery Holder

Wall Plate

Diagram 1

City Series | 29

Page 30

installation

Vent Restrictor Position

Vent restriction is required for certain venting installations, see the diagrams in the "Venting Arrangements" section to determine if they are required for your installation.

The Vent Restrictor plate is packed in the instruction manual package.

To set the vent restriction as indicated in the venting arrangements diagrams, refer to the following instructions;

1. Remove the safety glass and ﬁrebox glass - see instructions in this manual.

2. Remove the screws that hold the vent restrictor plate in place (see Diagram 1)

3. Adjust the vent restrictor plate to the required vent restrictor position as per the diagrams shown.

4. Once the vent restrictor plate is in the required position, secure with screws.

Vent restrictor positions:

Set 0 (Full open) Factory set

Set 1 (Vent restrictor at 2”)

Set 2 (Vent restrictor at 1.75”)

Screw locations

Vent restrictor location - inside top of rebox

Diagram 1

30 | City Series

Set 3 (Vent restrictor at 1.5”)

Page 31

installation

Horizontal Terminations

Flex Vent 4" x 6-7/8"

These venting systems, in combination with the CC40LE/CC40RE Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock Hersey/ Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent

Termination Locations" section.

Regency® Direct Vent (Flex) System Termination Kits includes all the parts needed to install the CC40LE/CC40RE using a ﬂexible vent.

FPI Kit # Length Contains:

#946-513 2 Feet 1. 6-7/8” ﬂexible outer liner (Kit length)

#946-515 4 Feet

#946-516 10 Feet

Notes:

1. Liner sections should be continuous without any joints or seams.

2. Only Flex pipe purchased from Regency® may be used for Flex installations

3. Horizontal vent must be supported every 3 feet.

4. Regency® Direct Vent System (Flex) is only approved for horizontal terminations.

5. Flex system can only be used up to a maximum continuous vent length of up to 10 feet. If longer runs are required, rigid pipe must be used.

2. 4” ﬂexible inner liner (Kit length)

3. spring spacers

4. thimble

5. AstroCap termination cap

6. screws

7. tube of Mill Pac

8. plated screws

9. S.S. screws #8 x 1-1/2” drill point

Vent Guard - if required*

(Part #946-506/P)

City Series | 31

Page 32

installation

Venting Introduction

The CC40LE/CC40RE uses the "balanced ﬂue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These ﬂue pipes must not be connected to any other appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

Venting Arrangement for Horizontal Terminations

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o (two 45o elbows equal one 90o elbow).

Note: When using rigid vent pie systems, the rigid pipe adapter (Part# 510-994) must be used in all applications.

56-1/4” (1429mm)

VENT RESTRICTOR SETTING: Vent restrictor factory set at Set 0.

Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 0 to Set 2 if required.

NOTE: A minimum of 1' (305mm) vertical off the top of the unit is required before any horizontal runs can start.

Note: For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum continuous

vent length of up to 10 feet. If longer runs are required, rigid pipe must be used.

• Maintain clearances to combustibles as listed in "Clearances" section

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂoor level and whenever passing through a wall.

• A vent guard should be used whenever the termination is lower than the speciﬁed minimum or as per local codes.

• Flex system can only be used up to 10 feet - otherwise rigid venting must be used.

32 | City Series

Page 33

Horizontal Terminations

Rigid Pipe 4" x 6-5/8"

The minimum components required for a basic horizontal termination are:

1 Horizontal Termination Cap 1 Rigid Pipe Adaptor (510-994) 1 Wall Thimble 1 Length of pipe to suit wall thickness (see chart)

Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap. For siding other than vinyl furring strips may be used instead of the vinyl siding standoff, to create a level surface to mount the vent terminal. The Terminal must not be recessed into siding. Measure the wall thickness including furring strips.

If a Vinyl Siding Standoff is required (it must be used with vinyl siding), measure to outside surface of wall without siding and add 2 inches.

installation

Horizontal

Termination Cap

Vinyl Siding

Standoff (Optional)

Flat Wall Installation

Wall Thickness

(inches)

4" - 5-1/2" 6"

7" - 8-1/2" 9"

10" - 11-1/2" 12"

9" - 14-1/2' 11" - 14-5/8" Adj. Pipe

15" - 23-1/2" 17" - 24" Adj. Pipe

WARNING:

Do not combine venting components from different venting systems.

Use of the the AstroCapTM and FPI Riser is acceptable with all systems.

This product has been evaluated by Intertek for using a Rigid Pipe Adaptor in conjunction with Duravent Direct-Vent, Selkirk Direct-Temp, Ameri Vent Direct Venting, ICC Excel Direct and Security Secure Vent systems. Use of these systems with the Rigid Pipe adaptor is deemed acceptable and does not affect the Intertek WHI listing of components.

Vent Length Required

(inches)

Adj.Pipe Length

90 Elbow

Pipe Length

Rigid Pipe Adapter

Wall Thimble

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

The FPI AstroCap can Metal Products Ameri Vent Direct Vent, Security Secure Vent®, ICC Excel, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

and FPI Riser Vent terminal are certiﬁed for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent, Ameri-

City Series | 33

Page 34

installation

Horizontal Terminations

Rigid Pipe 4" x 6-5/8"

The diagrams below show examples of horizontal termination arrangements using one, two, or three 90o elbows (two 45o elbows equal one 90o elbow)

1. A maximum of three 90o elbows are permitted.

2. Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂoor level and whenever passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994) when using rigid pipe vent systems.

• A vent guard should be used whenever the termination is lower than the speciﬁed minimum or as per local codes.

• Flex system can only be used up to 10 feet - otherwise rigid venting must be used.

Horizontal Venting with Two (2) 90o Elbows

One 90o elbow = Two 45o elbows.

Option V H + H1

A) 1' Min. 2' Max.

B) 2' Min. 4' Max.

C) 3' Min. 5' Max.

D) 4' Min. 6' Max.

E) 5' Min. 7' Max.

F) 6' Min. 8' Max.

Restrictor Set 0 - Factory Setting

With these options, maximum total pipe length is 30 feet with minimum of 6 feet total vertical and maximum 8 feet total horizontal.

Please note minimum 1 foot between 90o elbows is required.

Horizontal Venting with Three (3) 90o Elbows

One 90o elbow = Two 45o elbows.

Option V H V + V1 H + H1

A) 1' Min. 1' Max. 2' Min. 2' Max.

B) 1' Min. 2' Max. 3' Min. 3' Max.

C) 2' Min. 2' Max. 5' Min. 4' Max.

D) 3' Min. 2' Max. 7' Min. 5' Max.

E) 4' Min. 3 Max. 9' Min. 6' Max.

F) 5' Min. 4' Max. 10' Min. 7' Max.

G) 6' Min. 5' Max. 11' Min. 8' Max.

H) 7' Min. 6' Max. 12' Min. 9' Max.

Restrictor Set 0 - Factory Setting

With these options, max. total pipe length is 30 feet with min. of 12 feet total vertical and max. 9 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

34 | City Series

Page 35

Vertical terminations

Rigid Pipe 4" x 6-5/8"

The minimum components required for a basic vertical termination are:

1 Vertical Termination Cap 1 Rigid Pipe Adaptor (510-994) 1 Ceiling Firestop 1 Flashing 1 Storm Collar 1 Length of pipe to suit wall thickness (see chart)

Galvanized pipe is desirable above the rooﬂine due to its higher

corrosion resistance. Continue to add pipe sections through the ﬂashing until the height of the vent cap meets the minimum height requirements speciﬁed in diagram 2 or local codes. Note that for steep roof pitches, the vertical height must be increased. A poor draft, or down drafting can result from high wind conditions near big trees or adjoining roof lines, in these cases, increasing the vent height may solve the problem.

installation

Roof Pitch Minimum Vent

Height

Feet Meters

ﬂat to 7/12 2 0.61

over 7/12 to 8/12 2 0.61

over 8/12 to 9/12 2 0.61

over 9/12 to 10/12 2.5 0.76

over 10/12 to 11/12 3.25 0.99

over 11/12 to 12/12 4 1.22

over 12/12 to 14/12 5 1.52

over 14/12 to 16/12 6 1.83

over 16/12 to 18/12 7 2.13

over 18/12 to 20/12 7.5 2.29

over 20/12 to 21/12 8 2.44

Diagram 2

WARNING:

Do not combine venting components from different venting systems.

Use of the the AstroCapTM and FPI Riser is acceptable with all systems.

Diagram 1

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

and FPI Riser Vent terminal are certiﬁed for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent, Ameri-

City Series | 35

Page 36

installation

Venting Arrangement for Vertical Terminations

Vertical Venting with straight Vertical venting and or with a max. of two (2) 90o Elbows (1 - 90

The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using two 90o elbows, with Rigid Pipe Venting Systems.

Two 45

elbows equal to one 90o elbow.

• Vent must be supported at offsets.

• Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂoor level and whenever passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994) when using rigid pipe vent systems.

• Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 0 through to Set 3 if required.

Vent Restrictor on Set 3

Horizontal (Feet)

10 12 16

Maximum: 37 ft. (11.2m)

o =

2 - 45o)

Vertical Height (Feet)

Vent Restrictor on Set 2

Vent Restrictor on Set 1

Minimum

8’6” (2.6m)

Maximum: 27 ft. (8.2m)

36 | City Series

Minimum length of pipe

between elbows 12” (305mm)

(1429mm)

Min. 56-1/4”

Page 37

Vertical Terminations Rigid Pipe 4" x 6-5/8"

installation

• Two 45

• Vent must be supported at offsets.

• Minimum distance between elbows is 1 ft. (305mm).

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂoor level and whenever passing through a wall.

• Must use optional rigid pipe adaptor (Part# 510-994) when using rigid pipe vent systems.

elbows equal to one 90o elbow. Maximum of six 45o elbows allowed.

Vertical Venting with Three (3) 90o Elbows

One 90o elbow = Two 45o elbows.

Option V H + H1 V + V1

A) 1' Min. 2' Max 3' Min.

B) 2' Min. 3' Max 4' Min.

C) 3' Min. 4' Max 6' Min.

D) 4' Min. 5' Max 7' Min.

E) 5' Min. 6' Max 8' Min.

F) 6' Min. 7' Max 9' Min.

G) 7' Min. 8' Max 10' Min.

Lengths do not include elbow indicated

With these options, max. total pipe length is 30 feet with min. of 10 feet total vertical and max. 8 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

City Series | 37

Page 38

installation

56-1/4" (1429mm)

Min. height

Unit Installation with Horizontal Termination

4" x 6-5/8" venting

(Rigid Vent Systems)

Minimum Vent Clearances to Combustibles

Clearances noted below must be maintained; except when passing through a wall, ceiling or at the termination

where the use of a restop or wall thimble reduces

clearance to 1-1/2" (38mm).

Horizontal Top 3" (76mm)

Horizontal Side 2 " (51mm)

Horizontal Bottom 2" (51mm)

Vertical Vent 2" (51mm)

Below are the recommended framing dimensions (inside measurements) for the 4" x 6-5/8" rigid vent terminations - for use with a ﬁrestop or wall thimble.

Recommended Framed Opening

Size

Vent Size Framing Size

4" x 6 - 5/8" 10" x 10"

Install the vent system according to the manufacturer's instructions included with the components.

1. Set the unit in its desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the unit. Rough in the gas preferably on the right side of the unit and the electrical (junction block is on the left side) on the left.

2. Direct Vent pipe and ﬁttings are designed with special twist-lock connections to connect the venting system to the appliance ﬂue outlet. A twist-lock appliance adaptor is required.

3. In conjunction with the Approved Vent system, install the adaptor after the unit is set in its desired location. Put a bead of Mill-Pac inside the outer section of the adapter and a bead of Mill-Pac on the inner collar. Slip the adapter over the existing inner and outer ﬂue collar. Fasten to the outer collar only with the 3 supplied screws (drilling pilot holes will make this easier).

4. Level the ﬁreplace and fasten it to the framing using nails or screws through the top and side nailing strips.

5. Assemble the desired combination of pipe and elbows to the appliance adaptor and twist-lock for a solid connection.

Note: For best results and optimum

performance with each approved venting system, it is highly recommended to apply Mill-Pac sealant (supplied) to every inner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty.

Horizontal runs of vent must be supported every 3 feet (0.9meter). Wall straps are available for this purpose.

6. Mark the wall for a square hole.-see chart to left for size. The center of the square hole should line up with the center-line of the horizontal pipe. Cut and frame the square hole in the exterior wall where the vent will be terminated. See diagram 2 for center line requirements.

If the wall being penetrated is constructed of

non-combustible material, i.e. masonry block or concrete, an 8" (203mm) diameter hole is acceptable.

Note:

a) The horizontal run of vent must be level, or

have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a ﬁre.

b) The location of the horizontal vent

termination on an exterior wall must meet all local and national building codes.

center

of hole

(Rigid)

Diagram 2

7. Ensure that the pipe clearances to combustible materials are maintained (Diagram 3). Install the termination cap.

Note: If installing termination on a vinyl

siding covered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is not recessed into the siding.

Diagram 3

The four wood screws provided should be

replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

8. Before connecting the horizontal run of vent pipe to the vent termination, slide the Wall Thimble over the vent pipe. The wall thimble is required for all horizontal terminations.

9. Slide the appliance and vent assembly towards the wall carefully inserting the vent pipe into the vent cap assembly. It is important that the vent pipe extends into the vent cap sufﬁcient distance so as to result in a minimum pipe overlap of 1-1/4 inches (32mm). Secure the connection between the vent pipe and the vent cap.

10. Install wall thimble in the center of the framed hole and attach with wood screws (Diagram 4).

Diagram 4

Diagram 1

38 | City Series

Page 39

installation

Furstrp.eps

see also c34020a.eps

(294mm)

56-1/4”

Unit Installation with Horizontal Termination

4" X 6-5/8" VENTING

(Flex Vent Systems)

Minimum Vent Clearances to Combustibles

Clearances noted below must be maintained; except when passing through a wall, ceiling or at the termination

where the use of a restop or wall thimble reduces

clearance to 1" (25mm).

Horizontal Top 3" (76mm)

Horizontal Side 2 " (51mm)

Horizontal Bottom 2" (51mm)

Vertical Vent 2" (51mm)

Below are the recommended framing dimensions (inside measurements) for the 4" x 6-5/8" rigid

vent terminations - for use with a restop or wall

thimble.

Recommended Framed Opening

Vent Size Framing Size

4" x 6 - 5/8" 10" x 10"

1. Locate the unit in the framing, rough in the gas (preferably on the right side of the unit). Locate the centerline of the termination and mark wall accordingly. Cut an square hole in the wall - see chart (inside dimension).

Note: If installing termination on a siding covered

wall, a vinyl siding standoff or vinyl furring strips must be used to ensure that the termination is not recessed into the siding.

2. Level the ﬁreplace and fasten it to the framing using nails or screws through the nailing strips.

3. Assemble the vent assembly by applying Mill Pac to the inner ﬂue collar of the termination and slipping the inner ﬂex liner over it at least 1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill-Pac to the outer ﬂex pipe and slip it over the outer ﬂue collar of the vent terminal at least 1-3/8"(35mm) and fasten with the 3 screws.

Size

Outside Wall

Furring

Strips

NOTE: Horizontal sections must be sup-

ported at intervals not exceeding 3 feet (0.9 meter). (Flame picture and performance will be affected by sags in the liner).

4. Separate the 2 halves of the wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom. Fasten the other thimble half to the inside wall. The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 walls.

5. Slip the assembled liner and termination assembly through the thimble making sure the termination cap faces up (there are markings on the cap indicating which way is up). This will position the termination cap with proper down slope for draining water. Fasten the cap to the outer wall with the 4 supplied screws.

6. Pull the centre inner and outer ﬂex liner out enough to slip over the ﬂue collars of the ﬁreplace. (You may wish to cut the liner shorter to make it more workable.) Do not bend liner more than 90o. The liners must slip over the collars a minimum of 1-3/8".

7. Apply Mill Pac over the ﬁreplace inner ﬂue collar and slip the inner ﬂex liner down over it and attach with 3 supplied screws.

8. Do the same with the outer ﬂue collar and outer ﬂex liner.

9. Apply a bead of silicone between the thimble and termination and around the outer edge of the terminal at the wall in order to keep the water out.

IMPORTANT: Do not locate termination hood

where excessive snow or ice buildup may

occur. Be sure to check vent termination area after snow falls, and clear to prevent

accidental blockage of venting system. When using snow blowers, make sure snow is not

directed towards vent termination area.

Screws

(3 per

connection)

4" (102mm) dia. flue pipe

with spring spacer

6-7/8" (173mm) dia. air intake

Wall Thimble 2 pieces

(10" (254mm)

Outer Diameter)

ASTROCAP DIMENSIONS (946-523/P)

(294mm)

11”

2” x 4” or 2” x 6”

Termination

Cap

Screws

(4 per

connection)

11”

of hole

(1429mm)

Min.

City Series | 39

Page 40

installation

56-1/4” (1429mm)

Dura-Vent Horizontal terminations

Install the vent system according to the manufacturer's instructions included with the components.

1) Set the unit in its desired location. Check to

determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the unit. Rough in the gas preferably on the right side of the unit and the electrical (junction block is on the left side) on the left.

2) Direct Vent pipe and ﬁttings are designed with special twist-lock connections to connect the venting system to the appliance ﬂue outlet. A twist-lock appliance adaptor is an available option that must be used in conjunction with the Simpson Dura-Vent Direct Vent system.

3) Put a bead of Mill-Pac inside the outer section of the adaptor and on the inner collar. Slip the adapter over the existing inner and outer ﬂue collar and fasten to the outer collar only with the 3 supplied screws (drilling pilot holes will make this easier). Level the ﬁreplace and fasten it to the framing using nails or screws through the nailing strips.

4) Assemble the desired combination of pipe and elbows to the appliance adaptor and twist-lock for a solid connection.

Note: a) Twist-lock procedure: Four indenta-

tions, located on the female ends of pipes and ﬁttings, are designed to slide straight onto the male ends of adjacent pipes and ﬁttings, by orienting the four pipe indentations so they match and slide in to the four entry slots on the male ends, Diagram 1. Push the pipe sections completely together, then twist-lock one section clockwise approximately onequarter turn, until the two sections are fully locked. The female locking lugs will not be visible from the outside, on the Black Pipe or ﬁttings. They may be located by examining the inside of the female ends.

b) Horizontal runs of vent must be supported

every three feet. Wall straps are available for this purpose.

5) Mark the wall for a 10" x 10" square hole. The center of the square hole should line up with the centerline of the horizontal pipe. Cut and frame the 10 inch square hole in the exterior wall where the vent will be terminated. If the wall being penetrated is constructed of noncombustible material, i.e. masonry block or concrete, a 7"(178mm) dia. (7-1/2"(191mm) dia. for ﬂex) hole is acceptable.

Diagram 2

Note:

a) The horizontal run of vent must be level, or

have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a ﬁre.

b) The location of the horizontal vent

termination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. For External Vent Terminal Locations, see the "Exterior Vent Termination Locations" section.

c) Snorkel Terminations: For installations requiring a vertical rise on

the exterior of the building, 14-inch and 36inch tall Snorkel Terminations are available, as well as the standard Riser Vent. Follow the same installation procedures as used for standard Horizontal Termination. NEVER

install the snorkel upside down.

Note: Riser Vent is only for use in above grade terminations.

Diagram 3a

*Diagrams 3 & 4: As speciﬁed in CGA B149 Installation Code. Local codes or regulations may require different clearances.

Below Grade Installation

If the Snorkel Termination must be installed below grade, i.e. basement application, proper drainage must be provided to prevent water from entering the Snorkel Termination. Refer to Diagram 4. Do not attempt to enclose the Snorkel within the wall, or any other type of enclosure.

Diagram 1

NOTE: For best results and optimum performance with each approved venting system, it is highly recommended to apply “Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty.

40 | City Series

Diagram 4

NOTE: For Snorkel terminations in

ABOVE grade installations, follow national or local code requirements.

6) The arrow on the vent cap should be pointing up. Insure that the 1-1/2" clearances to

combustible materials are maintained (Diagram

4). Install the termination cap.

The four wood screws provided should be

replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

Page 41

installation

Dura-Vent Vertical Termination

4" x 6-5/8" venting

(Rigid Vent Systems)

1. Maintain the 1-1/2" clearances (air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafter, or other nearby combustible surfaces. Do not pack air spaces with insulation. Check "Venting" Sections for the maximum vertical rise of the venting system and the maximum horizontal offset limitations.

2. Set the gas appliance in its desired location. Drop a plumb bob down from the ceiling to the position of the appliance ﬂue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, and mark the spot where the vent will penetrate the roof.

3. A ﬁrestop spacer must be installed in the ﬂoor or ceiling of every level. To install the Firestop spacer in a ﬂat ceiling or wall, cut a 10 inch square hole. Frame the hole as shown in Diagram 2 and install the ﬁrestop.

Note: All vertical terminations are vented using 4" x 6-5/8" venting and rigid pipe adaptor #510-994.

Diagram 1

4. Assemble the desired lengths of pipe and elbows. Ensure that all pipes and elbow connections are in the fully twist-locked position and sealed.

5. Cut a hole in the roof centered on the small

drilled hole placed in the roof in Step 2. The hole should be of sufﬁcient size to meet the minimum requirements for clearance to combustibles of 1-1/2". Slip the ﬂashing under the shingles (shingles should overlap half the ﬂashing) as per Diagram 3.

Diagram 3

Diagram 3: The upper half of the ashing is installed under the roong material and not nailed down until the chimney is installed. This allows for small

adjustments.

Diagram 4

Roof Pitch Minimum Vent Height

Feet Meters

ﬂat to 7/12 2 0.61

over 7/12 to 8/12 2 0.61

over 8/12 to 9/12 2 0.61

over 9/12 to 10/12 2.5 0.76

over 10/12 to 11/12 3.25 0.99

over 11/12 to 12/12 4 1.22

over 12/12 to 14/12 5 1.52

over 14/12 to 16/12 6 1.83

over 16/12 to 18/12 7 2.13

over 18/12 to 20/12 7.5 2.29

over 20/12 to 21/12 8 2.44

7. Ensure vent is vertical and secure the base of the ﬂashing to the roof with rooﬁng rails, slide storm collar over the pipe section and seal with a mastic.

8. Install the vertical termination cap by twistlocking it.

Note: Any closets or storage spaces, which

the vent passes through must be

enclosed.

Diagram 2

City Series | 41

6. Continue to assemble pipe lengths.

Note: If an offset is necessary in the attic

to avoid obstructions, it is important to support the vent pipe every 3 feet, to avoid excessive stress on the elbows, and possible separation. Wall straps are available for this purpose.

Galvanized pipe is desirable above the rooﬂine

due to its higher corrosion resistance. Continue to add pipe sections through the ﬂashing until the height of the vent cap meets the minimum height requirements speciﬁed in Dia. 4 or local codes. Note that for steep roof pitches, the vertical height must be increased. A poor draft, or down drafting can result from high wind conditions near big trees or adjoining roof lines, in these cases, increasing the vent height may solve the problem.

Page 42

installation

VERTICAL TERMINATION

4" X 6-7/8" VENTING - VERTICAL FLEX VENT KIT (946-755)

Flashing

Termination Cap

Storm Collar

Roof support

Vertical Termination 4" x 6-7/8" venting

1. Maintain the 1-½” clearance (air space) to combustibles when passing

through ceilings, walls, ﬂ oors, enclosures, attic rafters or other nearby

combustibles. Do not pack air spaces with insulation. Check Venting sections for the maximum vertical rise of the venting system and the

maximum horizontal oﬀ set limitations.

Ensure that you maintain clearances around enclosures, walls, below

or above ﬂ oors, ﬂ oor joists, etc. Each appliance has diﬀ erent clearance requirements (top,sides,bottom). See speci c appliance manual for details.

2. Set the appliance in its desired position. Drop a plumb bob down from

the ceiling/ﬂ oor joist to the position of the appliance ﬂ ue exit and mark

the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next drop a plumb bob from the roof to the hole previously drilled at the ceiling level and mark the spot where the vent will penetrate the roof.

3. Cut a hole in the roof centered on the small hole placed in the roof in the previous steps. The hole should be a minimum of 10-¼ inches. The hole may be round and or square.

4. Slip the ﬂ ashing under the shingles and line up ﬂ ashing so it is centered

to the hole (shingles should overlap half of the ﬂ ashing) as per Diagram

Diagram 1: The upper half of the  ashing is

installed under the roo ng material and not

nailed down until the chimney is installed.

This allows for small adjustments.

Diagram 1

5. A ceiling  restop/ restop spacer must be installed when passing through each ﬂ oor or ceiling level. To install the ceiling  restop/ restop spacer in a ﬂ at ceiling or ﬂ oor joist cut a 10- ¼ inch square hole. Frame the hole as show in Diagram 1 and install the ceiling  restop. Slide the top attic insulation spacer onto the top of the attic insulation shield/ restop - See

Diagram 1a. Secure with 4 screws/nails. If more than one is required, these can be purchased separately.

11. Secure inner ﬂ ex pipe to pipe adaptor by using Mill-Pac over the adaptor.

Slide the inner pipe over adaptor and secure with 3 screws.

12. Repeat Step 11 to secure outer ﬂ ex.

13. Slide the  nished length up towards the ﬂ ashing ensuring the length of

pipe is a minimum of 2 feet measured from the top of the roof. Level the chimney and secure using the roof support provided with kit to bottom side of the roof as shown using a minimum of 2 screws per side- see Diagram 3b. See Diagram 4 for roof pitch and height requirements. See

Diagram 3a for securing method if 2 ft. is insuﬃ cient and additional lengths

are required, this may be purchased separately. See Simpson Duravent components list in the instruction manual for part numbers.

Termination Cap

Storm Collar

Flashing

Roof Support / Brace

Ceiling Firestop

Flex Pipe

Support to prevent sagging

Elbow Support

Termination Cap

Storm Collar

Flashing

Roof Support

Ceiling Firestop

Enclosure

Ceiling Firestop

Flex Pipe

Diagram 3 Diagram 3a

Termination Cap

Storm Collar

Flashing

Note: The ceiling  restop/ restop spacer may be cut down to size if this

shield is too high for the application.

-1/4

Diagram 2

Ceiling ﬁrestop

Firestop spacer to prevent

debris from falling into the

ceiling  restop

Ceiling firestop

Enclosure

Diagram 2a

Ceiling firestop

6. Determine the overall height of the chimney from the top of the appliance

to the underside of the ﬂ ashing. If required cut the ﬂ exible inner and outer

pipe to the desired length up to a maximum of 20 feet.

7. Put a bead of Mill-Pac around the 4 inch collar on the appliance and slide

the inner ﬂ ex pipe over the inner collar of the appliance and secure with

a minimum of 3 screws.

8. Install 4 inch spacers around 4 inch ﬂ ex.

9. Repeat Step 7 to install the outer pipe to the outer collar of the appliance

Note: If an oﬀ set is necessary in the attic or ﬂ oor joists it is important to

support the vent pipe every 3 feet to avoid excessive stress and sagging of the vent pipe. Wall straps are provided (3 in total) for this purpose. All round/plumbers strapping may also be used if further supports are required.

10. Attach the rigid pipe section to the adaptor by using Mill-Pac on the inner/ outer pipe. Use 3 screws to secure outer pipe.

Roof support

Diagram 3b

Diagram 4

Roof Pitch Minimum Vent Height

Feet Meters

ﬂ at to 7/12 2 0.61

over 7/12 to 8/12 2 0.61

over 8/12 to 9/12 2 0.61

over 9/12 to 10/12 2.5 0.76

over 10/12 to 11/12 3.25 0.99

over 11/12 to 12/12 4 1.22

over 12/12 to 14/12 5 1.52

over 14/12 to 16/12 6 1.83

over 16/12 to 18/12 7 2.13

over 18/12 to 20/12 7.5 2.29

over 20/12 to 21/12 8 2.44

14. Put a bead of caulking on the exterior between the outer pipe and ﬂ ashing

to prevent water from penetrating the chimney system.

15. Slide storm collar over pipe length until it reaches the ﬂ ashing.

16. Install termination cap by twist locking it.

17. Secure the ﬂ ashing to the roof using screws

Note: Any closets or storage spaces which the vent passes through must

be enclosed.

42 | City Series

Page 43

VERTICAL FLUE EXTENSION KIT (PART # 946-756)

919-698

08.10.16

-1/4

Ceiling ﬁrestop

Diagram 1

Diagram 1a

Enclosure

Ceiling firestop

Flashing

Termination Cap

Storm Collar

Roof support

Ceiling firestop

Flashing

Termination Cap

Storm Collar

Roof support

Firestop spacer to prevent

debris from falling into the ceiling

restop

A ceiling restop/restop spacer must be installed when passing through each oor or ceiling level. To install the ceiling restop/restop spacer in a at ceiling or oor joist cut a 10- ¼ inch square hole. Frame the hole as show in Diagram 1 and install the ceiling restop. Slide the top attic insula- tion spacer onto the top of the attic insulation shield/restop - See Diagram 1a. Secure with 4 screws/nails. If more than one is required, these can be purchased separately.

Note: The ceiling restop/restop spacer may be cut down to size if this shield

is too high for the application

CEILING FIRESTOP/FIRESTOP SPACER ( PART # 946-757)

The ceiling restop/restop spacer may be cut down to size if this shield

CEILING FIRESTOP/FIRESTOP SPACER ( PART # 946-757)

Vertical ﬂue extension kit (part #946-756)

20 foot Flex pipe Extension

(Used in conjunction with the 946-755 Vertical Flex kit and 948-367/P ex to ex adaptor).

1. Stretch out both inner 4" (100 mm) and outer 6 7/8" (175mm) pipe up to a maximum of 20 feet.

Note :The inner and outer pipes may be cut if only a short length is required.

2. Install spring spacers around 4" (100 mm) inner pipe as shown.

Slide outer ex pipe over and all the way down the 4" pipe.

3. Apply a bead of Mill Pac around the perimeter of the 4" (100mm) inner collar of the ex adapter and slip the 4" (100mm) inner ex pipe from the Vertical termination kit over the ex adapter ensuring that the inner ex pipe overlaps the collar by at least 1-3/8" (35mm). Fasten with 3 screws.

4. Apply a bead of Mill Pac around the perimeter of the 6-7/8" (175mm) outer collar of the ue adapter and slip it over the 6-7/8" (175 mm) outer ex pipe from the vertical termination kit ensuring that the outer ex pipe overlaps the collar by at least 1-3/8" (35mm). Fasten with the 3 screws.

5. Repeat steps to secure the other end of the ex adapter using the ex kit.

6. See Vertical Vent installation instructions for installation of the complete vent system.

4" (100mm) inner pipe

6-7/8" (175mm)

outer ex pipe

20ft

installation

20ft.

10 spring spacers

ex adaptor

3 wall straps

Note: If an o󰀨set is necessary in the attic or oor joists it is important to support the vent pipe every 3 feet to avoid excessive stress and sagging of the vent pipe. Wall straps are provided (3 in total) for this purpose.

All round/plumbers strapping may also be used if further supports are required.

Ceiling Firestop / ﬁrestop spacer (part #946-757)

A ceiling restop/restop spacer must be installed when passing through each oor or ceiling level. To install the ceiling restop/restop spacer in a at ceiling or oor joist cut a 10- ¼ inch square hole. Frame the hole as show in Diagram 1 and install the ceiling restop. Slide the top attic insulation spacer onto the top of the attic insulation shield/restop - See Diagram 1a. Secure with 4 screws/nails. If more than one is required, these can be purchased separately.

Note:

is too high for the application

-1/4

Ceiling ﬁrestop

Firestop spacer to prevent

Diagram 1

debris from falling into the ceiling

restop

Enclosure

City Series | 43

Ceiling firestop

Page 44

installation

CC40LE/CC40RE NG SYSTEM DATA

Min. Supply Pressure

Manifold Pressure 3.8" WC (0.94 kpa)

Orice Size #42 DMS

Maximum Input 28,500 Btu/h

Minimum Input 15,500 Btu/h

5" WC (1.25 kpa)

(8.33 kW)

(4.54 KW)

CC40LE/CC40RE LP SYSTEM DATA

Min. Supply Pressure 11" WC (2.73 kpa)

Manifold Pressure 10.5" WC (2.62 kpa)

Orice Size #53 DMS

Maximum Input 28,500 Btu/h

Minimum Input 15,500 Btu/h

(8.35 kW)

(4.54 KW)

High Elevation

This unit is approved for altitude 0 to 4500 ft. (CAN1

2.17-M91).

Gas Line Installation

Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or ﬂex connectors use only approved ﬁttings. Always provide a union so that gas lines can be easily disconnected for servicing. Flare nuts for copper lines and ﬂex connectors are usually considered to meet this requirement.

NOTE: A shutoff / dante valve should be supplied in or near the unit (or as per local codes) for ease of servicing this appliance.

IMPORTANT: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open ﬂame for leak testing.

Pilot Adjustment

Periodically check the pilot ﬂames. Correct ﬂame pattern has two strong blue ﬂames: 1 ﬂowing around the ﬂame sensor and 1 ﬂowing across the burner (it does not have to be touching the burner).

Burner

Flame Sensor

Pilot

Ignitor

Note: If you have an incorrect flame

pattern, contact your Regency® dealer for further instructions.

Incorrect ﬂame pattern will have small, probably yellow ﬂames, not coming into proper contact with the rear burner or ﬂame sensor.

Gas Pipe Pressure Testing

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1 Make sure the unit is in the "OFF" position.

2. Loosen the "IN" and/or "OUT" pressure tap(s), turning counterclockwise with a

1/8" wide ﬂat screwdriver.

3. Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4. Turn the unit on with the remote or wall switch

5. The pressure check should be carried out with the unit burning and the setting should be within the limits speciﬁed on the safety label.

885 S.I.T. Valve Description

1) 6 Stage ﬂame adjustment

2) Pilot adjustment

3) Outlet Pressure Tap

4) Inlet Pressure Tap

5) Pilot Outlet

6) Main Gas Outlet

7) Main Gas Inlet

44 | City Series

6. When ﬁnished reading manometer, turn off the unit, disconnect the hose and tighten the screw (clockwise) with a 1/8" ﬂat screwdriver.

Note: Screw should be snug, but do not over tighten.

Page 45

Wiring Diagrams

installation

No electrical power supply is required for the gas control to operate. 120 Volt AC power is needed for the lights. A receptacle box, receptacle and cover are provided and located on the left hand side of the unit, under the outer base panel.

Electrical power must be brought to the appliance by a licensed electrician.

(Do not cut the ground terminal off under any circumstances.)

BLACK

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

BATTERY CONNECTION

BATTERY

HOLDER

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded threeprong receptacle. Do not cut or remove the grounding prong from this plug.

VARIABLE LIGHTS

City Series | 45

Page 46

installation

Inner glass panel (ﬁrebox glass) Installation / removal

Note: glass panels must be installed to operate ﬁreplace

WARNING: GLASS HANDLING

We recommend using the glass vacuum holders supplied by the manufacturer. Lower the glass to rest in a safe place, this is to prevent damage to the glass edges. Extra care must be taken when removing/installing the glass. Breakage or damage to the edge of the glass which occurs as a result of careless handling will not be covered under warranty.

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant surface to place the glass

• Never clean or remove hot glass

Note: The suction cups may leave a round ﬁlm on the glass when used. Ensure that the glass is cleaned using a ﬁreplace glass cleaner prior to operating the appliance.

Important:

Prior to installing the inner glass, ensure that there is no media present in the bottom channel as this can cause damage to the glass. Remove any media from bottom channel prior to installing the glass.

1. Remove outer safety glass panels if previously installed–see instructions in this manual.

2. CC40LE/CC40RE Single sided & CC40LE/CC40RE 3 Sided Units—Re- move outer panels installed in units - see panel removal section in this manual.

Push side glass panel rmly

to back wall until springs are

compressed—

then close

clamps.

4. With the springs compressed, close the 2 clamps at the bottom and 2 clamps at the top, by turning inward, to secure the glass in position. For the 3 sided unit, repeat on the opposite side.

Single sided units–proceed to Step 5.

3. Ensure all 4 clamps on each side are open to allow clearance for the glass. Lift up side panel using supplied vacuum clamp and tilt inward and upward positioning into a top channel and lowering gently into the lower glass channel–slide the side glass panel ﬁrmly towards the back wall until the springs at the back wall are compressed.

Top clamps in

open position

Bottom side clamps in

open position

Bottom

channel

Top clamps in

closed position

Bottom clamps in

closed position

CC40LE/CC40RE shown

46 | City Series

Page 47

installation

5. Ensure all 7 front clamps are in the open position to allow clearance for the glass.

Open clamps prior to placing front glass panel

CC40LE shown

6. Lift up the front panel using the supplied vacuum clamps and position into the lower front channel–ensure the front panel is accurately centered—with the front panel in position—secure in place by closing the 3 lower clamps and 4 upper clamps.

Press glass vacuum clamps in open position ﬁrmly onto surface of glass. Bring handles together to close.

Note: Ensure that the front glass is centered and evenly spaced with side glass (3 sided unit) - open to release glass clamps to remove from surface of glass.

Open clamps to release pressure on the springs

7. Return to the side panel(s), and release the upper and lower clamps. The springs will release and push the glass side panel forward slightly—this will create a seal between the front and side panels. When the junction between the front and side glass panels is sealed, close the clamps to secure the side panel(s) in place.

Open

Handle front panel with supplied vacuum clamps

Closed

8. To remove the glass panels—always remove the side panel(s) (for 3 sided units) before removing the front panel.

9. Reverse steps to remove glass.

City Series | 47

Page 48

installation

Outer safety glass panel (barrier glass) Installation / removal

Note: safety glass panels must be installed to operate ﬁreplace

3. Tilt the top of the glass panel inward and lift up and underneath

WARNING: GLASS HANDLING

• We recommend handling the glass with supplied vacuum

clamps

• When removing glass–prepare a soft, scratch resistant surface to place the glass

• Never clean or remove hot glass

Note: The suction cups may leave a round ﬁlm on the glass when used. Ensure that the glass is cleaned using a ﬁreplace glass cleaner prior to operating the appliance.

Outer glass safety panels to be installed during the initial installation after the unit is in the ﬁnal position.

Note: The outer safety panels come with plastic corners to protect these against damage. These should be kept in place until such time the outer safety panels are installed. Ensure these are removed prior to operating the appliance. Keep the plastic corners in a safe place if ever removing the outer panels for servicing.

the upper front panel of the outside frame. Hook the glass panel onto the pins and also onto the two angle adjustment brackets located on the frame in two locations as shown in the diagram below. Note: The front frame upper panel is shown as transparent to better illustrate the install (this area is not visible when installing glass).

1. Carefully remove glass safety panels from packaging.

Press glass vacuum clamp in open position ﬁrmly onto surface of glass. Bring handles together to close.

Open

NOTE: Inner glass panel shown in image - depicting proper handling of glass.

Closed

Pins on body of unit

Angle adjustment brackets

Note: If the outer safety glass panels do not sit at 90º and angle too far

inward or outward, remove the glass panel and adjust the screw of the panel angle bracket. Turn the panel angle bracket screw in 1/4 increments—reinstall panel to check.

Panel angle bracket—to adjust, turn screw:

Clockwise = bring panel in

2. Using the supplied vacuum clamps, lift the large front glass panel and position it front and centre by manoeuvering up and underneath the front of the unit frame.

48 | City Series

Counter clockwise= bring panel out

Page 49

Outer safety glass panel (barrier glass) Installation / removal

Note: safety glass panels must be installed to operate ﬁreplace.

4. For 3 sided and corner units only: With front panel installed, proceed to install the side panel(s). Identify the left and right side panels before installing. Facing the front of

the unit, the right panel will show an arrow pointing to the front of the unit as shown in the diagram below.

Direction arrow on side

panel bracket, should

point toward front of

unit

Note: After the side panel has been adjusted so it is installed at 90º to the

unit and not ﬂaring in or out, check to ensure there is no gap between the front and side panel. If there is a gap as shown below, slide the side panel to adjust the position and close the gap.

installation

5. Lift up the side panel with the supplied glass clamps (see procedure on previous page). Tilt the side of the glass panel inward and lift up and underneath the upper side panel and hook the 2 outer hooks on to the pins, there is also a panel angle adjustment bracket for the third hook.

Note: The side frame upper panel is shown as transparent to better illustrate the install (this area is not visible when installing glass).

Note: If the outer safety glass side panels angle too far inward or outward,

remove the side glass panel and adjust on the panel angle bracket, see details on previous page.

6. Repeat Steps 4 and 5 to install the opposite side panel.

7. Reverse Steps to remove all panels.

Note: When removing panels, we recommend using the supplied glass clamps.

City Series | 49

Panel angle bracket

Page 50

installation

CITY SERIES

CONVERSION FROM NG TO LP

CV40E/ CB40E using SIT 885 NOVA Gas Valve

LP Conversion Instructions

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION!

WARNING

This conversion kit shall be installed by a qualiﬁ ed service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If these instructions is not followed exactly, a ﬁ re, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualiﬁ ed service agency is responsible for the proper installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked as speciﬁ ed in the manufacturer’s instructions supplied with the kit.

Conversion Kit 656-969 includes:

1 911-191 Stepper Motor LP for 885 SIT

1 904-947 Oriﬁ ce #53

1 910-101 Pilot Oriﬁ ce #35

1 918-590 Decal - Conversion to LP

1 908-528 Label Propane

1 904-529 5/32" long Allen Key

Caution: The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion.

Always let the appliance cool to room temperature before servicing.

1. Remove the outer panels and safety glass — see manual.

6. If unable to access this Cable - undo 2 screws securing the IFC Board and slide out of unit to access cable.

7. Remove and discard 2 Pressure regulator screws (A)using a (T20 or slot screwdriver,) Pressure Regulator (B) and Spring and Diaphragm (C) (see below).

8. Ensure the rubber gasket, which is preﬁ tted as part of the Assembly,

is properly positioned. Install the new Pressure Regulator using the 2x M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that the screw threads are cross threaded or stripped, replace the valve assembly.

Install the enclosed propane identiﬁ cation label to the valve body where it can be easily seen.

Pressure regulator

screws

2. Remove inner ceramic glass — see manual.

3. Remove inner panels — see manual.

4. Remove all media installed on burner (glass, logs or stones, etc).

5. Disconnect the Cable coming from the Pressure Regulator Motor.

50 | City Series

9. Re-attach the Pressure Regulator wire (disconnected in Step 6), and resituate the IFC, secure the screws that fasten the IFC Mounting Brackets.

10. Remove pilot hood by lifting up and off.

Cable from motor

Page 51

CITY SERIES

11. Loosen 4 screws in locations shown below (2 at front and 2 at rear)—slide burner to the left away from the oriﬁ ce and lift out.

front

screw locations

back screw locations

installation

14. Unscrew the pilot oriﬁ ce with the allen key; then replace with the LPG pilot oriﬁ ce and the pilot cap, provided in the kit.

12. Remove burner oriﬁ ce with a 3/8" wrench. Use another wrench to hold on to the elbow behind the oriﬁ ce. Discard oriﬁ ce. Reinstall new burner oriﬁ ce LPG stamped #53 and tighten.

CV40E shown

13. Remove pilot retainer clip with pliers and pull off the pilot cap to expose the pilot oriﬁ ce.

Burner Oriﬁ ce

Location

15. Reinstall pilot cap and pilot retainer clip.

16. Prior to installing burner—adjust aerations settings - to 1/4" for LP. Reinstall burner (see Step 13).

17. Ensure the pilot light is in the correct orientation to the Burner. Reconnect the gas and electrical supply to the appliance. Start the appliance. (see section on Lighting Instructions) Ensure that pilot and burner ignition is completed without delay. Check both your inlet and outlet pressures at full load. With a soapy solution, leak test the entire system. Verify both the correct ﬂ ame and pilot appearance.

11. See Gas Pipe Pressure Testing in manual.

City Series

LP SYSTEM DATA

Min. Supply Pressure 11" WC (2.73kpa)

Manifold Pressure - High 10.5" WC (2.62 kpa)

Manifold Pressure - Low 2.9" WC (0.72 kpa)

Oriﬁ ce Size #53 DMS

Maximum Input 28,500 Btu/h (8.35 kW)

Minimum Input 15,500 Btu/h (4.54 KW)

Altitude 0-4500 ft (0-1372m)

Pilot retainer clip

City Series | 51

Installer Notice:

These instructions must be left

with the appliance.

Page 52

installation

CC40RE/CC40LE INNER PANELS

5. Manoeuvre in side panel to the side wall of the unit—secure in place

The CC40RE/CC40LE can be equipped with optional steel inner panels.

CITY SERIES

CC40LE/CC40RE Painted panel installation

Inner Panels - CC40LE/CC40RE

There are 4 outer panels and 3 inner panels.

NOTE: CC40RE shown in diagrams—CC40LE panels install in the same order. Installed panels for the CC40LE will appear as mirror images of diagrams shown below.

Turn off unit and allow to cool to room temperature. Remove the safety glass and ﬁrebox glass — see manual for instructions.

1. Install inner lower base panel.

2. Install panel clips into the slots at the top of the back panel as shown.

with 1 panel clips and 1 screws.

Panel Clip

6. Reverse steps to remove panels.

Outer Panels - CC40LE/CC40RE

CC40RE/CC40LE OUTER PANELS

Note: Install inner safety glass prior to installation of outer panels-see instructions in manual

1. Attach Regency logo to the right hand side of outer front panel. The magnets will be positioned under the outer front base panel to secure the logo. The logo should be about 3 inches from the right hand corner of the outer base. Install outer front and side base panel.

3. Manoeuvre in back panel to the back wall of the unit—secure in place with 2 panel clips and 2 screws.

Panel Clips

4. Install panel clip into the slots at the top of the

side panel as shown.

Location of

Regency Logo

Outer base panel install

2. Install side panels - the side panels are secured in place by existing magnets in the unit.

Outer side panel install

3. Install outer safety glass.

4. Reverse steps to remove panels.

52 | City Series

Page 53

CC40LE/CC40RE glass panel installation

CC40LE/CC40RE GLASS PANEL INSTALLATION

CITY SERIES

installation

1. Turn off unit and allow to cool to room temperature. Remove the outer safety glass and inner ceramic ﬁ rebox glass panels and any media installed — see manual for instructions. CC40RE shown in diagrams.

NOTE: CC40RE shown in diagrams—CC40LE panels install in the same order. Installed panels for the CC40LE will appear as mirror images of diagrams shown below.

2. Identify panels and order of installation.











Y5PQ$PSOFS#SBDLFU$$-

Y5PQ$PSOFS#SBDLFU$$3

Y5PQ#BDL#SBDLFU

Y5PQ4JEF#SBDLFU





4. Slide the supplied bottom corner bracket behind the small panel (1) and the back and side walls, in the orientation shown below.

bottom

corner bracket

656-206

base panel

back bracket

base panel

5. Carefully manoeuvre the back glass panel (2) to the back wall of the ﬁ rebox. Center the glass panel and position bottom of panel into brackets installed in step 4. Place the 2 top back brackets on the top edge of the glass and secure to the unit with one screw on each side once back glass panel is in position.

back wall of unit

bottom

656-218

Y#PUUPN#BDL#SBDLFU

Y#PUUPN$PSOFS#SBDLFU

Glass Panel Parts Layout

3. Install the inner base panel (1) around burner as shown below.

bottom corner

brackets

Top back

bracket

orientation

656-202

Top back

bracket location

656-202

City Series | 53

Page 54

installation

Bottom Side Bracket

CITY SERIES

6. Carefully manoeuver the Side Glass Panel (3) into the side of the ﬁ rebox. Position the bottom of the panel into the Bottom Corner Bracket and secure the top using the Top Side Bracket as shown. Once in position, secure the Top Side Bracket to the side wall with one screw. Slide the appropriate Top Corner Bracket over the corner between the Side and Back glass panels.

656-205

656-203

Use with CC40R

656-203

656-204

Use with CC40L

656-202

9. Install outer side base panel (5) — panel 5 rests on the tab of panel 4.

anel 7

Panel 5

Tab on Panel 4

10. Install outer side panels (6, 7) — both panels are held in position with magnets.

nel 6

7. Reinstall inner ceramic ﬁ rebox glass panels (see manual for instructions).

8. Install front outer base panel (4) Note: there are tabs on panel 4 that should face inward.

Panel 4

Panel 6

Tab

Outer side panels

(6, 7)

11. Install outer safety barrier glass (3 pieces). See manual for instructions.

12. Reverse Step 1 to reassemble unit.

13. Reverse steps to remove panels.

54 | City Series

Page 55

maintenance

CITY LINE

CC40LE/CC40RE enamel panel installation

Black Enamel Panels — Handling Instructions

• Black Enamel panels must be inspected for scratches and dimples prior to installation.

All claims to be recorded at this time. Claims for damage after installation will not receive consideration.

• Black Enamel panels will discolor a little during normal operation. This is normal and should not be considered a defect.

All hand and ﬁ nger marks MUST be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any ﬁ ngerprints before

applying heat to the unit.

Failure to do this will result in burn stain on panels which you will be unable to remove and will not be protected by product warranty.

The CC40RE/CC40LE can be equipped with optional enamel panels. There are 4 outer panels and 3 inner panels.

NOTE: CC40RE shown in diagrams—CC40LE panels install in the same order. Installed panels for the CC40LE will appear as mirror images of diagrams shown below.

Tu rn off unit and allow to cool to room temperature. Remove the safety glass and ﬁ rebox glass — see manual for instructions

CC40RE/CC40LE INNER PANELS

1. Install inner lower base panel.

2. Install panel clips into the slots at the top of the back panel as shown.

3. Manoeuvre in back panel to the back wall of the unit—secure in place with 2 panel clips and 2 screws.

Panel Clips

4. Install panel clip into the slots at the top of the side panel as shown.

5. Manoeuvre in side panel to the side wall of the unit—secure in place with 1 panel clip and 1 screw.

City Series | 55

Panel Clip

6. Reverse steps to remove panels.

Page 56

maintenance

CC40RE/CC40LE OUTER PANELS

CITY LINE

Note: Install inner safety glass prior to installation of outer panels-see instructions in manual

Location of

Regency Logo

Outer base panel install

2. Install side panels - the side panels are secured in place by existing magnets in the unit.

Outer side panel install

3. Install outer safety glass.

4. Reverse steps to remove panels.

56 | City Series

Page 57

installation

Burner and Firebox media options

Spread the media evenly over the burner. Ensure the glass/stones do not overlap excessively as this will affect the ﬂame pattern.

IMPORTANT NOTE:

Only the supplied approved media are to be used with these ﬁreplaces. Use of any other type of glass or stones can alter the unit's performance. Any damage caused by the use of any unapproved glass or stones will not be covered under warranty. When using Ceramic Spa/Volcanic Stones ensure required glass crystals/beads are used as a base. DO NOT overstack Ceramic Spa Stones or Volcanic Stones on burner or in the pilot area. Media must be installed on and around burner only in amounts noted below.

CC40LE/CC40RE Approved Media*

Fireglass (starﬁre, copper or black) On burner 1.5 lbs

Glowing embers/sea wool (supplied with unit) On burner 1 bag

Natural Stones Around burner 1 box = 15lbs

Ivory Natural Stones Around burner 1 box = 15lbs

3/4" Crushed black glass Around burner 3.5lbs

Crushed Iceburg chips Around burner 3.5lbs

Firebeads Around burner 3.5lbs

Spa stones Around burner 2 boxes

Lava Embers Around burner 6 packages

Stone River Pebbles Around burner 2 bags

* Media not supplied with unit - must be purchased separately.

3/4" Crushed black glass + Black Fireglass

Where Used Quantity

Natural / Ivory Stones + Fireglass

Starre Fireglass + Iceburg chips

Fireglass + Firebeads

Lava Embers + Black Fireglass

City Series | 57

Spa Stones + Fireglass

Stone River Pebbles + Fireglass

Page 58

installation

CITY LINE

CITY LINE - LOG INSTALLATION

Optional driftwood Log set Installation

Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with pilot operation.

Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty.

*Dark brown paint is included if touch ups are required.

1 Rear Log

2 Left Log

3 Right Log

4 Left Cross Log

5 Right Cross Log

6Front Left Log Piece

7Front Right Log Piece

Log Brackets (3)

Lava rock (purchased separately from log set)

1.5 lb Black Fireglass (purchased separately from log set)

Glowing wool (supplied with unit)

3/4" Crushed black glass or iceburg chips (purchased separately from log set)

5. Clip on the log guides - position the rear guides by centering over the second and fourth ver tical lines at the back of the burner. The front log guide clips on to the front edge of the burner on the right side as shown below.

Log Guides - location of log guides,

6. Centre Log 1 and rest on installed rear log guides—with pins facing up.

2 rear - 1 front

Log guides

6 7

1. S hut off gas and electrical supply, allow unit to cool to room temperature.

2. Remove safety glass and ﬁ rebox glass (see manual).

3. Carefully remove the logs from the packaging and unwrap them. The logs are fragile, handle with care—never force into position.

4. Install Black Fireglass(1.5lb) and glowing wool on the burner as shown below.

Burner covered with Fireglass and glowing wool

Log 1 in position

7. Position Log 2 on the burner—the longest point of Log 2 should sit level at the left edge of the burner — the other end of the log on a slight diagonal to the front of the ﬁ rebox as shown.

Point of log to edge

of burner

Log 2 in position

58 | City Series

Page 59

installation

CITY LINE

8. Place the split end of Log 3 to the right front corner of the burner—angle the log so that the other end is sitting approximately 1/2" (13mm) from the edge of the burner tray.

Log to corner of

Log 3 placement

9. Place Log 6 and Log 7 on the burner locations shown below.

10. Before placing the next log—spread the optional media evenly

throughout the burner tray as shown.

3/4" Crushed black

glass on burner tray

burner

Rest the other end of Log 4 on the indent in Log 2 as shown below.

Indent Log 2

12. Place Log 5—identify the pin locator and match with the right side pin on Log 1.

Pin in Log 1

NOTE: Ensure the installed optional media doesn't completely block the air ﬂ ow—ensure more than 50% of the airﬂ ow is open (shown with 3/4" crushed black glass).

Do not completely

block air ﬂ ow

11. Place Log 4—identify the pin locator and match with the left side pin on Log 1.

Pin in Log 1

Rest the other end of Log 5 on the indent in Log 3 as shown below.

Add lava rock sparsely around the perimeter of the burner.

City Series | 59

Completed Install

Page 60

installation

CC40LE/CC40RE - Removable drywall guides

(when using 1/2" drywall)

An optional ﬁnishing trim is available to ﬁnish the edges of the installation on the CC40RE/CC40LE unit. Installation is as follows:

1. Remove the outer safety glass and outer front and side panels - see instructions in manual.

2. Loosen 3 screws inside the lower front edge of the unit to release existing lower drywall guide and remove guide.

Note : an offset screwdriver is provided with the appliance for ease of removal/

installation of the lip and ﬁnishing trim.

Lower drywall

guides

Loosen and tighten screws on drywall guide from inside front panel

3. Loosen 2 screws from inside the ﬁrebox to release the existing side drywall guide, remove guide and recycle.

5. Reverse steps to reinstall drywall guides (if applicable). If discarding, please recycle.

4. Loosen 2 screws from inside the ﬁrebox to release the existing side drywall guide, remove guide and recycle.

Loosen 2 screws from inside the rebox to remove the side drywall trim

pieces

60 | City Series

Page 61

operating instructions

First Fire

The FIRST FIRE in your ﬁreplace is part of the paint curing process. To ensure the paint is properly cured, it is recommended you burn your ﬁreplace for at least four (4) hours the ﬁrst time.

When ﬁrst operated, the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours. The glass may require cleaning.

NOTE: When the glass is cold and the

appliance is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS STILL HOT!

DO NOT BURN THE UNIT WITHOUT THE GLASS IN PLACE.

During the ﬁrst few ﬁres, a white ﬁlm may develop on the glass front as part of the curing process. The glass should be cleaned after the unit has cooled down or the ﬁlm will bake on and become very difﬁcult to remove. Use a non-abrasive cleaner and DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS HOT.

Normal Operating Sounds of Gas Appliances

It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. Listed below are some examples. All are normal operating sounds and should not be considered as defects in your appliance.

Burner Tray:

The burner tray is positioned directly under the burner tube(s) media and logs and is made of a different gauge material from the rest of the ﬁrebox and body. Therefore, the varying thicknesses of steel will expand and contract at slightly different rates which can cause "ticking" and "cracking" sounds. You should also be aware that as there are temperature changes within the unit these sounds will likely re-occur. Again, this is normal for steel ﬁreboxes.

Pilot Flame: While the pilot ﬂame is on it can make a very slight "whisper" sound.

Gas Control Valve: As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.

Unit Body/Firebox: Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.

Aeration Adjustment

The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue ﬂame or close for a more yellow ﬂame.

Remove outer safety glass and inner glass panels plus outer and inner base panels - see instructions in this manual.

2. Loosen 4 screws in locations shown below (2 at front and 2 at rear)—slide burner to the left away from the oriﬁce and lift out.

front

screw locations

back screw locations

3. Reverse steps to reinstall burner.

Minimum Air Shutter Opening:

NG Fully closed NG with Logs Fully closed NG with Stones Fully closed

LP 1/4" LP with Logs 1/4" LP with Stones 1/4"

Note: Any damage due to carboning

resulting from improperly setting the aeration controls is NOT covered under warranty.

City Series | 61

Page 62

operating instructions

Lighting Procedure

IMPORTANT: The remote control system supplied with this appliance has

several options for starting/operating the appliance using the battery holder and ON/OFF key on the hand held transmitter.

Prior to operating this appliance, please read the remote control operating

instructions (packaged with remote control) to understand how to operate this remote control system.

1. Ensure the battery holder switch is in the Remote position and / or wall mounted battery holder (if equipped) is in the <REMOTE> position.

2. Press and release the ON/OFF button on the remote handheld transmitter (see Diagram 1). An audible beep should be heard from the receiver. If not using the remote, the unit can also be turned on by sliding the battery holder switch to the <ON> position (if equipped).

ON/OFF Button

Note: The ﬁrst try for ignition will last approximately 60 seconds. If there is no

ﬂame ignition (rectiﬁcation) the board will stop sparking for approximately 35 seconds. After wait time , the board will start second try for ignition by sparking for approximately 60 seconds . If there is still no positive ignition the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off by pressing the ON/OFF button on the remote. b) Wait 5 minutes then repeat from step 2.

Shutdown Procedure

1. Press the ON/OFF button on the remote

2. If service is to be performed, you must disconnect power and shut off gas

to the unit.

Remote shown in Manual Mode on Hi

Diagram 1

3. After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4. The unit will turn on.

* Not offered on all models.

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection

See remote control instructions for details.

62 | City Series

Page 63

Copy of the Lighting Plate Instructions

operating instructions

POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE

FOR YOUR SAFETY READ BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1.

Cet appareil doit être installé conformément aux codes locaux, s’il y a lieu. En l’absence de tels codes, suivre le National Fuel Gas Code, ANSI Z223.1/NFPA 54, ou les Natural Gas and Propane Installation Codes, CSA B149.1.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

AVERTISSEMENT : Quiconque ne respecte pas scrupuleusement les instructions de la présente notice risque de déclencher un incendie ou une explosion pouvant entraîner des dégâts matériels ou des blessures pouvant être mortelles. Tout défaut d'installation, de réglage, de modication, de service ou d'entretien peut entraîner des blessures ou des dommages matériels. Reportez-vous au manuel d'utilisation fourni avec cet équipement. Pour obtenir de l'aide ou des informa-

tions complémentaires, consulter un installateur ou un service d'entretien qualié, ou le fournisseur de gaz.

A) This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

C) Do not use this appliance if any part has been under water. Immediately call a qualied service

technician to inspect the appliance and replace any part of the control system and any gas control which has been underwater.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse. Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT LA MISE EN MARCHE, reniez tout autour de l’appareil pour déceler une odeur de gaz. Reniez au niveau du plancher, car certains gaz

sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne tentez pas d’allumer l’appareil

• Ne touchez à aucun interrupteur; n'utilisez pas de téléphones se trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un téléphone extérieur. Suivez les instructions du fournisseur.

• Si vous ne pouvez pas rejoindre le fournisseur, appelez le service incendie. C) N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement. Faites inspecter l’appareil par un technicien qualié et remplacez

tout élément du système de contrôle ou de commande qui a été plongé dans l’eau.

CAUTION: Hot while in operation. Do not touch. Severe burns may result. Due to high surface temperatures keep

children, clothing and furniture, gasoline and other liquids having ammable vapors away. Keep burner and control

compartment clean. See installation and operating instructions accompanying appliance.

ATTENTION : Surfaces chaudes lorsque l’appareil est en marche. Ne pas toucher. Risque de brûlures graves. En raison des températures élevées, les enfants, les vêtements et le mobilier, le carburant et tout autre liquide aux vapeurs

inammables doivent être tenus éloignés de l’appareil. Nettoyer régulièrement le brûleur et le compartiment des

commandes. Voir les consignes d’installation et d’utilisation fournies avec l’appareil.

LIGHTING INSTRUCTIONS / CONSIGNES D’ALLUMAGE

1) Ensure the Main switch is in the ON position and/or the wall mounted battery holder (if equipped) is in the <REMOTE> position.

2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be heard from the receiver. If not using the remote, the unit can also be turned on by sliding the battery holder switch to the <ON> position (if equipped).

3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

4) The unit will turn on.

Note: The rst attempt to ignition will last approximately 60 seconds. If there is no ame ignition (rectication) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the second attempt the board will go into lock out. The system will need to be reset as follows (after going into lock out mode): a) Wait 5 minutes - turn the system off by pressing the ON/OFF button on the remote. b) After approximately 2 seconds press the ON/OFF button again. c) Unit will repeat step 2.

1) S’assurer que le commutateur principal est en position ON et/ou que le bloc-piles mural (le cas échéant) est en position <REMOTE>.

2) Appuyer sur la touche ON/OFF de la télécommande puis relâcher. Un bip sonore retentira depuis le récepteur. Si vous n'utilisez pas la télécommande, l'appareil peut également être allumé en faisant glisser le commutateur du bloc-piles sur la position <ON> (le cas échéant).

3) Après environ 4 secondes, le système d'allumage produira une étincelle pendant 60 secondes pour allumer le brûleur principal.

4) L'appareil s’allumera.

Remarque : Au premier allumage, le système tente d’allumer les ammes pendant 60 secondes. Si l’essai est infructueux, le système fera une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectication. Ce délai écoulé, le système tente à nouveau d'allumer les ammes en produisant des étincelles pendant 60 secondes. Si les ammes ne s’allument toujours pas, le système se met en mode ver-

rouillage. Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) : a) Attendre 5 minutes et éteindre l’appareil en appuyant sur la touche ON/OFF de la télécommande. b) Attendre 2 secondes et appuyer encore une fois sur la touche ON/OFF.

c) L'appareil répètera l'étape 2.

TO TURN OFF GAS APPLIANCE / POUR ÉTEINDRE UN APPAREIL AU GAZ

1) Press the ON/OFF button on the remote.

2) If service is to be performed–you must disconnect power and shut off gas to the unit.

Appuyer sur la touche ON/OFF de la télécommande.

2) Lors de l'entretien de l'appareil, vous devez débrancher l'alimentation électrique et couper le gaz alimentant l'appareil.

DO NOT REMOVE THIS INSTRUCTION PLATE

NE PAS ENLEVER CETTE ÉTIQUETTE D’INSTRUCTIONS

919-649

City Series | 63

Page 64

maintenance

Maintenance Instructions

1. Always turn off the gas valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged.

2. Clean appliance and door with a damp cloth (never when unit is hot). Never use an abrasive cleaner. The glass should be cleaned with a gas ﬁreplace glass cleaner. The glass should be

cleaned when it starts looking cloudy.

3. The ﬁreplace is ﬁnished in a heat resistant paint and should only be reﬁnished with heat resistant paint. Regency® uses StoveBright Paint - Metallic Black #6309.

4. Make a periodic check of burner for proper position and condition. Visually check the ﬂame of the burner periodically, making sure the ﬂames are steady; not lifting or ﬂoating. If there is a problem, call a qualiﬁed service person.

5. The appliance and venting system must be inspected before use, and at least annually, by a qualiﬁed ﬁeld service person, to ensure that the ﬂow of combustion and ventilation air is not obstructed.

and exterior portions of the system being exposed to cold weather.

4. Inspect joints, to verify that no pipe sections or ﬁttings have been disturbed, and consequently loosened. Also check mechanical supports such as Wall Straps, or plumbers' tape for rigidity.

Log Replacement

The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door and carefully remove the logs. (The pilot light generates enough heat to burn someone.) If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the diagrams under Log Installation.

Note: Improper positioning of logs may

create carbon build-up and will severely alter the unit's performance which is not covered under warranty.

Glass Gasket

If the glass gasket requires replacement use a tadpole glass gasket (Part # 936-220).

Glass replacement

In the event that you break your glass by impact, purchase your replacement from an authorized Regency dealer only. Replacement glass is shipped already installed into the door frame. Reinstall as per Glass Installation in the "Glass Installation" section.

REPLACEMENT GLASS:

CC40LE/CC40RE

Inner Glass Front - Ceramic (Part# 940-436/P) Inner Glass Side - Ceramic (Part# 940-437/P)

CC40LE

Outer Safety Glass Side - Tempered Large #940-486/P Outer Safety Glass Side - Tempered Small # 940-439/P

CC40RE

Outer Safety Glass Side - Tempered Large #940-485/P Outer Safety Glass Side - Tempered Small #940-440/P

Note: Never operate the appliance without

the glass properly secured in place.

6. Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service technician to inspect the appliance and to replace nay part of the control system and any gas control which has been under water.

7. In the event this appliance has been serviced check that the vent-air system has been properly resealed & reinstalled in accordance with the manufacturer's instructions.

8. Verify operation after servicing.

General Vent Maintenance

Conduct an inspection of the venting system semiannually. Recommended areas to inspect as follows:

1. Check the Venting System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These components should be replaced immediately.

2. Remove the Cap, and shine a ﬂashlight down the Vent. Remove any bird nests, or other foreign material.

Glass

Your Regency® ﬁreplace is supplied with high temperature 5mm-Tempered outer glass & 5mmCeramic inner glass. If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials.

CAUTION & WARNINGS:

* Do not clean when the glass is hot. * The use of substitute glass will void all product warranties. * Care must be taken to avoid breakage of the glass. * Do not strike or abuse the glass. * Do not operate this ﬁreplace without the glass front or with a cracked or broken glass front. * Wear gloves when removing damaged or broken glass. * Replacement of the glass panels should be done by a licensed or qualiﬁed service per son.

3. Check for evidences of excessive condensation, such as water droplets forming in the inner liner, and subsequently dripping out the joints, Continuous condensation can cause corrosion of caps, pipe, and ﬁttings. It may be caused by having excessive lateral runs, too many elbows,

64 | City Series

Page 65

Bulb Replacement

maintenance

1. Turn off unit and allow to cool to room temperature.

2. Remove outer safety glass panels and inner panels (ﬁrebox glass)–see instructions in this manual.

3. Loosen 2 outer screws on each side to remove outer light cover — located in the upper inside front of the ﬁrebox and remove.

4. Loosen 2 screws on each side of individual inner light cover and remove.

5. Remove glass cover by using a ﬂat head screwdriver to pry the tab securing the glass assembly in place.

6. Replace bulb and reverse steps to complete procedure.

NOTE: Do not handle bulb with bare hands. Use packaging or a tissue to hold

new bulb when replacing.

Regency Part# 911-208 Oven Lamp Assembly G9 120V/25W Regency Part# 911-072 Replacement Bulb G9 120 Volt/25 watt

City Series | 65

Page 66

maintenance

tooltip

Valve Replacement

Important: Always shut off gas supply/120 volt power prior to servicing the

gas valve.

1. Turn off unit and allow to cool to room temperature.

2. Remove outer enamel or steel panels—see instructions in the panel removal section in this manual

3. Remove outer safety glass panels and inner panels (ﬁrebox glass)–see instructions in this manual.

4. Remove all media and logs (if installed) — set aside.

5. Loosen 4 screws in locations shown below (2 at front and 2 at rear)—slide burner to the left away from the oriﬁce and lift out.

front

screw locations

7. Lift valve tray by out partially and disconnect ﬂexible gas connection on the valve inlet side, remove valve tray- replace with new valve tray.

8. Reverse steps 6-1 to complete.

back screw locations

6. Remove 16 screws in locations shown below.

Remove 16 screws securing valve tray

66 | City Series

Page 67

CC40LE main assembly

parts list

1 656-525 Burner Assembly - NG/LP

2 656-046 Pilot Cover/Shield

4 911-006 Pilot Assembly IPI NG 2 Flame 0.199.050

4 911-007 Pilot Assembly IPI LP 2 Flame

5 911-188 Novasit Valve Only - NG 885 SIT IPI 0.885.009

5 911-189 Novasit Valve Only - LP 885 SIT IPI

6 656-276 IFC Cover/Shield

6A 911-174 IFC Board Complete 584.306

7 656-045 Burner Surround

8 940-486/P Outer Barrier Tempered Glass Assembly - Large

9 940-436/P Flush Inner Ceramic Glass - Large

N/S 656-062 Outer Base Cover Black

10 940-439/P Outer Safety Glass Side - Tempered Small

11 940-437/P Flush Inner Ceramic Glass Small

17 656-574/P Valve Assembly - NG

17 656-576/P Valve Assembly - LP

18 656-033F Bottom Cover Access Plate

18 656-034 Bottom Cover Access Gasket

19 656-309 Removable Drywall Finishing

20 656-124 Removable Drywall Finishing Trim

22 911-190 Stepper Motor NG SIT 0.907.015

22 911-191 Stepper Motor LP SIT 0.907.015

23 656-125 Removable Drywall Vertical Finishing Trim Left/Right

24 656-241F Nailing Strip Side

25 656-247F Nailing Strip Top

N/S 936-219 Gasket 5/8 (09) Sewn Rope Graphite 3/4 PSA 10

(Sold per Foot 10 Feet Required)

N/S 904-943 Bracket Dormont Oriﬁce Mount 10-BZ001-19.5

N/S 936-220 Gasket Tape 2" Wide Graphite Wrap

N/S 656-051 Bafﬂe Cover (Each)

N/S 904-996 Burner Oriﬁce #42 NG (PO512)

N/S 904-947 Burner Oriﬁce #53 LP (PO512)

N/S 910-100 Pilot Oriﬁce SIT - NG #62 977.166

N/S 910-101 Pilot Oriﬁce SIT - LP #35 977.168

N/S 911-037 Flame Sensor 0.915.905

N/S 911-038 Flame Electrode 0.915.020

N/S 910-432 Novasit Pilot Tubing With Nuts

N/S 911-039 Two Way Pilot Hood

N/S 911-137 Pilot Hood Clip

N/S 904-658 Inlet Flex Line Gas SS Steel 24 inch

N/S 904-606 Fitting 90 Street Elbow Extruded

N/S 904-165 Fitting 3/8 Male Flarex Mpt Strt Adaptor

N/S W840470 Pilot Assembly Gasket

N/S 656-040 Valve Assembly Gasket

N/S 656-039 Burner Oriﬁce Mount Gasket

N/S 911-175 Hand Held Remote Control GTMFL SIT 0.584.042

N/S 911-187 Remote Receiver/Battery Holder 584.103

N/S 910-576 Cover Wall Mount White GTM SIT 0.584.803

N/S 911-173 Wire Harness IFC No CPI Switch 584.924

N/S 911-177 Wire 4 Position IFC Fan & Light

N/S 911-181 Wire Harness Battery Box Proﬂame II

N/S 911-192 Power Cord 120 Volts With Connector

N/S 911-193 Connector With Jumper

N/S 911-209 Wire 2 Position IFC to Lights

N/S 910-369 Receptacle Box Low Voltage SC100A

N/S 910-428 Receptacle Duplex White

N/S 910-429 Receptacle Box Duplex Metal

N/S 910-430 Receptacle Cover Duplex Metal

N/S 904-687 Connector Clamp 3/8 CI-804

N/S 948-078 Glass Suction Cup (Each)

N/S 904-790 Magnet Round 1/2 inch (Each)

N/S 904-970 Magnet Cup 1/2 inch (Each)

N/S 948-223 Logo Plate Plastic Regency/Flame Silver

N/S 656-131 Logo Mounting Bracket

N/S 656-017F Restrictor Plate

N/S 656-018 Pressure Relief Base

N/S 656-023 Pressure Relief Base Gasket

N/S 656-019 Pressure Relief Bracket Right

N/S 656-020 Pressure Relief Bracket Left

N/S 656-021F Pressure Relief Door

N/S 656-022 Pressure Relief Door Gasket

N/S 656-075F Rear Standoff (Each)

N/S 911-208 Oven Lamp Assembly G9 120V 25W

N/S 656-086 Light Glass Bracket

N/S 911-072 Replacement Bulb G9 120 Volt/25 watt

N/S 656-087 Light Rear Louver

N/S 656-088 Light Cover Plate

N/S 656-089 Light Deﬂector Shield

N/S 656-085 Gasket Light Cover Gasket

N/S 656-079 Top Glass Clamp Left (Each)

N/S 656-080 Top Glass Clamp Right (Each)

N/S 656-269 Lower Glass Clamp (Each)

N/S 656-052 Lower Glass Clamp Bracket (Each)

N/S 656-617 Pressure Relief Door Frame Assembly/Includes Gasket

Optional Accessories

11 656-926* Inner Panel Glass Black

11 656-927* Inner Panel Black (Painted)

11 656-928* Inner Panel Enamel Black

* Sold only as complete sets

N/S 656-202 Top Rear Panel Clip (Used on the 656-926)

N/S 656-203 Top Corner Bracket (Used on the 656-926)

N/S 656-205 Glass Panel Top Side Bracket (Used on the 656-926)

N/S 656-205 Lower Corner Glass Bracket (Used on the 656-926)

N/S 656-218 Rear Base Panel Bracket (Used on the 656-926)

N/S 656-291 Inner Top Panel Clip (Used on the 656-927)

City Series | 67

Page 68

parts list

N/S 656-059 Inner Top Panel Clip (Used on the 656-928)

N/S 656-930/P Driftwood Log Set

N/S 656-969 Conversion Kit - LP

N/S 656-991 Chase Vent Front Black

N/S 656-995 Adaptor Heat Wave

N/S 946-556 Heatwave Kit

N/S 946-672 Stones - River Pebbles

N/S 946-674 Stones - Ceramic Spa (70 stones)

N/S 946-675 Fireglass Black Reﬂective 1/4in.1Lb Pkg

N/S 946-676 Fireglass Copper 1/4 in. 1Lb Pkg

N/S 946-677 Fireglass Starﬁre 1/4 in. 1Lb Pkg

N/S 946-775 Fireglass Black Reﬂective 1/4in.5Lb Pkg

N/S 946-776 Fireglass Copper 1/4 in. 5Lb Pkg

N/S 946-777 Fireglass Starﬁre 1/4 in. 5Lb Pkg

N/S 946-780 Crushed Glass Coal Black 3/4in. 3.5 Lbs

N/S 946-781 Crushed Glass Iceberg Chips 3/4in. 3.5 Lbs

N/S 946-735 Firebeads Black 1 Lb Pkg

N/S 946-736 Firebeads Sangria Luster 1 Lb Pkg

N/S 946-737 Firebeads Glacier Ice 1 Lb Pkg

N/S 946-738 Firebeads Caramel Luster 1 Lb Pkg

N/S 946-739 Firebeads Black 5 Lb Pkg

N/S 946-740 Firebeads Sangria Luster 5 Lb Pkg

N/S 946-741 Firebeads Glacier Ice 5 Lb Pkg

N/S 946-742 Firebeads Caramel Luster 5 Lb Pkg

N/S 946-710 Stones -Slate/Grey Basalt Natural 15 lbs

N/S 946-711 Stones - Ivory/Tan Basalt Natural 15 lbs

May not be exactly as shown

68 | City Series

Page 69

CC40RE main assembly

parts list

1 656-525 Burner Assembly - NG/LP

2 656-046 Pilot Cover/Shield

4 911-006 Pilot Assembly IPI NG 2 Flame 0.199.050

4 911-007 Pilot Assembly IPI LP 2 Flame

5 911-188 Novasit Valve Only - NG 885 SIT IPI 0.885.009

5 911-189 Novasit Valve Only - LP 885 SIT IPI

6 656-276 IFC Cover/Shield

6A 911-174 IFC Board Complete 584.306

7 656-045 Burner Surround

8 940-486/P Outer Barrier Tempered Glass Assembly - Large

9 940-436/P Flush Inner Ceramic Glass - Large

N/S 656-062 Outer Base Cover Black

10 940-438/P Outer Safety Glass Side - Tempered Small

11 940-437/P Flush Inner Ceramic Glass Small

12 936-219 Gasket 5/8 (09) Sewn Rope Graphite 3/4 PSA 10

(Sold per Foot 10 Feet Required)

N/S 936-220 Gasket Tape 2" Wide Graphite Wrap

17 656-574/P Valve Assembly - NG

17 656-576/P Valve Assembly - LP

18 656-033F Bottom Cover Access Plate

18 656-034 Bottom Cover Access Gasket

19 656-127 Removable Drywall Finishing Trim

20 656-293 Removable Drywall Finishing Trim

22 911-190 Stepper Motor NG SIT 0.907.015

22 911-191 Stepper Motor LP SIT 0.907.015

23 656-125 Removable Drywall Vertical Finishing Trim Left/Right

24 656-241F Nailing Strip Side

25 656-247F Nailing Strip Top

N/S 904-943 Bracket Dormont Oriﬁce Mount 10-BZ001-19.5

N/S 656-051 Bafﬂe Cover (Each)

N/S 904-996 Burner Oriﬁce #42 NG (PO512)

N/S 904-947 Burner Oriﬁce #53 LP (PO512)

N/S 910-100 Pilot Oriﬁce SIT - NG #62 977.166

N/S 910-101 Pilot Oriﬁce SIT - LP #35 977.168

N/S 911-037 Flame Sensor 0.915.905

N/S 911-038 Flame Electrode 0.915.020

N/S 910-432 Novasit Pilot Tubing With Nuts

N/S 911-039 Two Way Pilot Hood

N/S 911-137 Pilot Hood Clip

N/S 904-658 Inlet Flex Line Gas SS Steel 24 inch

N/S 904-606 Fitting 90 Street Elbow Extruded

N/S 904-165 Fitting 3/8 Male Flarex Mpt Strt Adaptor

N/S W840470 Pilot Assembly Gasket

N/S 656-040 Valve Assembly Gasket

N/S 656-039 Burner Oriﬁce Mount Gasket

N/S 911-175 Hand Held Remote Control GTMFL SIT 0.584.042

N/S 911-187 Remote Receiver/Battery Holder 584.103

N/S 910-576 Cover Wall Mount White GTM SIT 0.584.803

City Series | 69

N/S 911-173 Wire Harness IFC No CPI Switch 584.924

N/S 911-177 Wire 4 Position IFC Fan & Light

N/S 911-181 Wire Harness Battery Box Proﬂame II

N/S 911-192 Power Cord 120 Volts With Connector

N/S 911-193 Connector With Jumper

N/S 911-209 Wire 2 Position IFC to Lights

N/S 910-369 Receptacle Box Low Voltage SC100A

N/S 910-428 Receptacle Duplex White

N/S 910-429 Receptacle Box Duplex Metal

N/S 910-430 Receptacle Cover Duplex Metal

N/S 904-687 Connector Clamp 3/8 CI-804

N/S 948-078 Glass Suction Cup (Each)

N/S 904-790 Magnet Round 1/2 inch (Each)

N/S 904-970 Magnet Cup 1/2 inch (Each)

N/S 948-223 Logo Plate Plastic Regency/Flame Silver

N/S 656-131 Logo Mounting Bracket

N/S 656-017F Restrictor Plate

N/S 656-018 Pressure Relief Base

N/S 656-023 Pressure Relief Base Gasket

N/S 656-019 Pressure Relief Bracket Right

N/S 656-020 Pressure Relief Bracket Left

N/S 656-021F Pressure Relief Door

N/S 656-022 Pressure Relief Door Gasket

N/S 656-075F Rear Standoff (Each)

N/S 911-208 Oven Lamp Assembly G9 120V 25W

N/S 656-086 Light Glass Bracket

N/S 911-072 Replacement Bulb G9 120 Volt/25 watt

N/S 656-087 Light Rear Louver

N/S 656-088 Light Cover Plate

N/S 656-089 Light Deﬂector Shield

N/S 656-085 Gasket Light Cover Gasket

N/S 656-079 Top Glass Clamp Left (Each)

N/S 656-080 Top Glass Clamp Right (Each)

N/S 656-269 Lower Glass Clamp (Each)

N/S 656-052 Lower Glass Clamp Bracket (Each)

N/S 656-617 Pressure Relief Door Frame Assembly/Includes Gasket

Optional Accessories

11 656-926* Inner Panel Glass Black

11 656-927* Inner Panel Black (Painted)

11 656-928* Inner Panel Enamel Black

* Sold only as complete sets

N/S 656-202 Top Rear Panel Clip (Used on the 656-926)

N/S 656-203 Top Corner Bracket (Used on the 656-926)

N/S 656-205 Glass Panel Top Side Bracket (Used on the 656-926)

N/S 656-205 Lower Corner Glass Bracket (Used on the 656-926)

N/S 656-218 Rear Base Panel Bracket (Used on the 656-926)

N/S 656-291 Inner Top Panel Clip (Used on the 656-927)

N/S 656-059 Inner Top Panel Clip (Used on the 656-928)

N/S 656-930/P Driftwood Log Set

Page 70

parts list

N/S 656-969 Conversion Kit - LP

N/S 656-991 Chase Vent Front Black

N/S 656-995 Adaptor Heat Wave

N/S 946-556 Heatwave Kit

N/S 946-672 Stones - River Pebbles

N/S 946-674 Stones - Ceramic Spa (70 stones)

N/S 946-675 Fireglass Black Reﬂective 1/4in.1Lb Pkg

N/S 946-676 Fireglass Copper 1/4 in. 1Lb Pkg

N/S 946-677 Fireglass Starﬁre 1/4 in. 1Lb Pkg

N/S 946-775 Fireglass Black Reﬂective 1/4in.5Lb Pkg

N/S 946-776 Fireglass Copper 1/4 in. 5Lb Pkg

N/S 946-777 Fireglass Starﬁre 1/4 in. 5Lb Pkg

N/S 946-780 Crushed Glass Coal Black 3/4in. 3.5 Lbs

N/S 946-781 Crushed Glass Iceberg Chips 3/4in. 3.5 Lbs

N/S 946-735 Firebeads Black 1 Lb Pkg

N/S 946-736 Firebeads Sangria Luster 1 Lb Pkg

N/S 946-737 Firebeads Glacier Ice 1 Lb Pkg

N/S 946-738 Firebeads Caramel Luster 1 Lb Pkg

N/S 946-739 Firebeads Black 5 Lb Pkg

N/S 946-740 Firebeads Sangria Luster 5 Lb Pkg

N/S 946-741 Firebeads Glacier Ice 5 Lb Pkg

N/S 946-742 Firebeads Caramel Luster 5 Lb Pkg

N/S 946-710 Stones -Slate/Grey Basalt Natural 15 lbs

N/S 946-711 Stones - Ivory/Tan Basalt Natural 15 lbs

May not be exactly as shown

70 | City Series

Page 71

notes

City Series | 71

Page 72

warranty

Indoor Gas Products

Supplier

Labor

Coverage

Warranty Coverage Parts and Labor

Firebox and Heat Exchanger



Steel Burner Tube



Glass Thermal breakage only



All Surrounds/Inlays Finishes



Brick Panels/Log sets/Ceramic Burners

All Castings

Valve assembly and all gas control

Thermocouple, Thermopile)

All Other Electrical

Pack, Remote Control Systems)

Enamel Panels



Venting/Venting Components



All Stainless steel surrounds



All Firebox Media (Crystals,

Ceramic & Spa Stones)

All hardware

 1

Mesh/Glass Safety Barriers

 1

Accent Light Bulbs

 1

Glass (Crazing)

 1

Limited Lifetime Warranty

FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Lifetime Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below.

Some conditions apply (see below).

The policy is not transferable, amendable or negotiable under any circumstances.

Part

Lifetime 5 years 2 years 1 year Warranty (Years)

 3



components, (Pilot assembly, flame sensors, Spark Electrode, Pilot Tubing, Orifices,

 2

components,(Ignition Control Boards, Wiring, Switches, Blowers, Blower Control Module, Battery

Firebeads, Volcanic,

Conditions:

Warranty protects against defect in manufacture or FPI factory assembled components only, unless herein specified otherwise.

Any part(s) found to be defective during the warranty period as outlined above will be repaired or replaced at FPI’s option through an accredited distributor, dealer or pre-approved and assigned agent provided that the defective part is returned to the distributor, dealer or agent for inspection if requested by FPI. Alternatively, FPI may at its own discretion fully discharge all of its obligations under the warranty by refunding the verified purchase price of the product to the original purchaser. The purchase price must be confirmed by the original Bill of Sale.

The authorized selling dealer, or an alternative authorized FPI dealer if pre-approved by FPI, is responsible for all in-field diagnosis and service work related to all warranty claims. FPI is not responsible for results or costs of workmanship of unauthorized FPI dealers or agents in the negligence of their service work.

Revision Date: December 2016 Regency Gas Products Warranty

 2



72 | City Series

Page 73

At all times FPI reserves the right to inspect reported complaints on location in the field claimed to be defective prior to processing or authorizing of any claim. Failure to allow this upon request will void the warranty.

All warranty claims must be submitted by the dealer servicing the claim, including a copy of the Bill of Sale (proof of purchase by you). All claims must be complete and provide full details as requested by FPI to receive consideration for evaluation. Incomplete claims may be rejected.

Unit must be installed according to all manufacturers’ instructions as per the manual.

All Local and National required codes must be met.

The installer is responsible to ensure the unit is operating as designed at the time of installation.

The original purchaser is responsible for annual maintenance of the unit, as outlined in the owner’s manual. As outlined below, the warranty may be voided due to problems caused by lack of maintenance.

Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts

Exclusions:

This Limited Lifetime Warranty does not extend to paint, rust or corrosion of any kind due to a lack of maintenance or improper venting, combustion air provision, corrosive chemicals (i.e. chlorine, salt, air, etc.), door or glass gasketing.

Malfunction, damage or performance based issues as a result of environmental conditions, location, chemical damages, downdrafts, installation error, installation by an unqualified installer, incorrect chimney components (including but not limited to cap size or type), operator error, abuse, misuse, use of improper fuels , lack of regular maintenance and upkeep, acts of God, weather related problems from hurricanes, tornados, earthquakes, floods, lightning strikes/bolts or acts of terrorism or war, which result in malfunction of the appliance are not covered under the terms of this Limited Lifetime Warranty.

FPI has no obligation to enhance or modify any unit once manufactured (i.e. as products evolve, field modifications or upgrades will not be performed on existing appliances).

This warranty does not cover dealer travel costs for diagnostic or service work. All labor rates paid to authorized dealers are subsidized, pre-determined rates. Dealers may charge homeowner for travel and additional time beyond their subsidy.

Any unit showing signs of neglect or misuse will not be covered under the terms of this warranty policy and may void this warranty. This includes units with rusted or corroded fireboxes which have not been reported as rusted or corroded within three (3) months of installation/purchase.

Units which show evidence of being operated while damaged, or with problems known to the purchaser and causing further damages will void this warranty.

Units where the serial no. has been altered, deleted, removed or made illegible will void this warranty.

Minor movement, expansion and contraction of the steel is normal and is not covered under the terms of this warranty.

Freight damages for products or parts are not covered under the terms of the warranty.

Products made or provided by other manufacturers and used in conjunction with the FPI appliance without prior authorization from FPI may void this warranty.

warranty

Revision Date: December 2016 Regency Gas Products Warranty

City Series | 73

Page 74

warranty

Canadian Warrantor:

Canada, V4G 1H4

U.S. Warrantor:

United States, 98231

Limitations of Liability:

The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, FPI MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. IF IMPLIED WARRANTIES CANNOT BE DISCLAIMED, THEN SUCH WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some U.S. states do not allow limitations on how long an implied warranty lasts, or allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

Customers located outside the U.S. should consult their local, provincial or national legal codes for additional terms which may be applicable to this warranty.

How to Obtain Warranty Service:

Customers should contact the authorized selling dealer to obtain warranty service. In the event the authorized selling dealer is unable to provide warranty service, please contact FPI by mail at the address listed below. Please include a brief description of the problem and your address, email and telephone contact information. A representative will contact you to make arrangements for an inspection and/or warranty service.

FPI Fireplace Products International Ltd. 6988 Venture St. Delta, British Columbia

Fireplace Products U.S., Inc. PO Box 2189 PMB 125 Blaine, WA

Or contact the Regency Customer Care Centre at 1-800-442-7432 (phone) / 604-946-4349 (fax)

Product Registration and Customer Support:

Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form at http://www.regency-fire.com/Customer-Care/Warranty-Registration.aspx within ninety (90) days of purchase.

Revision Date: December 2016 Regency Gas Products Warranty

74 | City Series

Page 75

Product Registration and Customer Support:

Warranty Details

Serial Number (required):

Purchase Date (required) (mm/dd/yyyy):

Product Details

Product Model (required):

Dealer Details

Dealer Name (required):

Dealer Address:

Dealer Phone #:

Installer:

Date Installed (mm/dd/yyyy):

Your Contact Details (required)

Name:

Address:

Phone:

Email:

For purchases made in CANADA:

Canada, V4G 1H4

For purchases made in the UNITED STATES:

Fax: 604-946-4349

Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.

For purchases made in CANADA or the UNITED STATES:

http://www.regency-fire.com/Customer-Care/Warranty-Registration.aspx

For purchases made in AUSTRALIA:

http://www.regency-fire.com.au/Customer-Care/Warranty-Registration.aspx

You may also complete the warranty registration form below to register your Regency Fireplace Product and mail and/or fax it back to us, and we will register the warranty for you. It is important you provide us with all the information below in order for us to serve you better.

Warranty Registration Form (or Register online immediately at the above Web Site):

warranty

FPI Fireplace Products International Ltd.

6988 Venture St. Delta, British Columbia

Phone: 604-946-5155

Fireplace Products U.S., Inc. PO Box 2189 PMB 125 Blaine, WA United States, 98231

Phone: 604-946-5155

For fireplace care and tips and answers to most common questions please visit our Customer Care section on our Web Site. Please feel free to contact your selling dealer if you have any questions about your Regency product.

City Series | 75

For purchases made in AUSTRALIA:

Fireplace Products Australia Pty Ltd

1- 3 Conquest Way Hallam, VIC Australia, 3803

Phone: +61 3 9799 7277 Fax: +61 3 9799 7822

Page 76