Regency B36XTCE User Manual

Download

Regency Bellavista

B36XTCE

Gas Fireplace

™

Owners &

Installation Manual

MODEL: B36XTCE

Medium DV Gas Fireplace

WARNING: If the information in these instructions are not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

FOR YOUR SAFETY Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Bellavista

B36XTCE Video

www.regency-ﬁ re.com

FOR YOUR SAFETY What to do if you smell gas: Do not try to light any appliance Do not touch any electrical switch:

do not use any phone in your building.

Immediately call your gas supplier

from a neighbour's phone. Follow the gas supplier's instructions.

If you cannot reach your gas

supplier, call the ﬁ re department.

919-154

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

10/30/13

To the New Owner:

Congratulations!

Y ou are the owner of a state-of-the-art Gas Fireplace by REGENCY

. The Bellavista™ B36XTCE has been designed to provide you with all the warmth and charm of a wood ﬁ replace at the ﬂ ick of a switch. The Bellavista™ B36XTCE has been approved by Warnock Hersey/Intertek for both safety and efﬁ ciency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.

Bellavista B36XTCE

Bellavista B36XT

Gas Fireplace Beneﬁ ts

Regency B36XTCE Gas Fireplace

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency® product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2009 / CSA 2.33-2009 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN / CGA 2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local codes.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.

Ensure that structural members are not cut or weakened during installation.

Regency B36XTCE Gas Fireplace

TABLE OF CONTENTS

SAFETY LABEL

Copy of Safety Decal .....................................................5

REQUIREMENTS

MA Code - CO Detector.................................................6

DIMENSIONS

Unit Dimensions ............................................................7

INSTALLATION

Important Message ......................................................8

Before You Start ............................................................8

General Safety Information............................................8

Installation Checklist .....................................................9

Locating Your Gas Fireplace .........................................9

Clearances ..................................................................10

Mantel Clearances.......................................................11

Mantel Leg Clearances................................................12

Non- Combustible Requirements: ...............................12

Framing ......................................................................13

Framing & Finishing.....................................................14

Tile Finish ............................................................14

Clean Finish .........................................................14

Unit Assembly Prior to Installation ...............................16

Top Standoff Assembly ........................................16

Nailing strips ........................................................16

Venting Introduction .....................................................18

Vent Restrictor, Bafﬂ e & Heat Deﬂ ector Installation ....19

Exterior Vent Termination Requirements .....................20

4" X 6-5/8" Rigid Pipe .................................................21

5" X 8" Rigid Pipe ......................................................23

AstroCap XL & Rigid REAR VENT KIT for CORNER

INST ALLATIONS .........................................................28

RIGID PIPE 5" x 8" ..............................................28

venting arrangements For Horizontal TerminationS

RIGID PIPE 4" x 6-5/8" ........................................29

Horizontal terminations ................................................31

Two (2) 90o Elbows (Rigid Pipe 4" x 6 - 5/8") ..............31

Horizontal terminations ................................................31

Three (3) 90o Elbows (Rigid Pipe 4" x 6 - 5/8") ............31

venting arrangements For Vertical TerminationS .32

RIGID PIPE 4" x 6-5/8" ........................................32

Vertical terminations ...................................................33

Three (3) 90o Elbows (Rigid Pipe 4" x 6 - 5/8") ............33

venting arrangements ..........................................34

With Co-linear Flex System .................................34

Vertical Terminations ...........................................35

Co-linear Flex System Into Masonry Fireplaces .35

Unit Installation with Horizontal Termination ...............36

4" x 6-5/8" or 5" x 8" Venting ......................................36

Unit Installation with Horizontal Termination ...............37

Unit installation with Vertical Termination ....................38

Gas Line Installation ....................................................38

Pilot Adjustment ...........................................................39

High Elevation .............................................................39

886 S.I.T. Valve Description .........................................39

Gas Pipe Pressure Testing ..........................................39

Conversion from NG to LP ..........................................40

Brick panel installation .................................................42

Optional black enamel panel installation .....................43

Log set installation .......................................................44

Optional Fan installation ..............................................47

AC power adaptor installation (for sureﬁ re systems) ...48

GT Remote installation ................................................49

Optional Wall Thermostat ...........................................50

Optional Remote Control .............................................50

Optional Wall Switch ....................................................50

GTM Remote installation .............................................51

GTMF Remote installation ...........................................53

Aeration Adjustment ....................................................56

Wiring diagram ............................................................56

PROFLAME SYSTEM WIRING diagram .....................56

Optional accent light Installation ..................................58

Mesh guard Installation ...............................................61

Flush glass door Installation ........................................62

OPERATING INSTRUCTIONS

Operating Instructions .................................................63

First Fire ......................................................................63

Lighting Procedure ......................................................63

Shutdown Procedure ...................................................63

Normal Operating Sounds of Gas Appliances .............63

Copy of Lighting Plate Instructions ..............................64

Maintenance Instructions.............................................65

Log Replacement ........................................................65

Bulb Replacement .......................................................65

Removing Valve ...........................................................66

Installing Valve .............................................................66

PARTS LIST

Main Assembly ............................................................67

Burner Assembly .........................................................69

WARRANTY

The Warranty: Limited Lifetime ...................................71

Regency B36XTCE Gas Fireplace

This is a copy of the label that accompanies each Bellavista™ B36XTCE Direct Vent Gas Fireplace. We have printed a copy of the contents here for your review.

NOTE: Regency

units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.

SAFETY LABEL

COPY OF SAFETY DECAL

Duplicate S/N

Listed:

VENTED GAS FIREPLACE HEATER /

4001172

Certified for/Certifi e pour: Tested to:

ANSI Z21.88-2009/CSA 2.33-2009

MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.

CAN/CGA-2.17-M91(R2009)

NATURAL GAS: Model B36XTCE-NG

WC/C.E.

Minimum supply pressure Manifold pressure high Manifold pressure low Orifice size Minimum input Maximum input Altitude

5.0" (1.25 kPa) WC/C.E.

3.5" (0.87 kPa) WC/C.E.

1.6" (0.40 kPa)

#35 DMS 21,500 Btu/h (6.3 kW) 31 ,000 Btu/h (9.09 kW) 0-4500 ft/pi (0-1372 m)

PROPANE GAS: Model B36XTCE-LP

Minimum supply pressure Manifold pressure high Manifold pressure low Orifice size Minimum input Maximum input Altitude

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1. This appliancemust beinstalled in accordancewith theStandard CAN/CSAZ240 MH, MobileHousing, inCanada, or withthe Manufactured Home Constructionand SafetyStandard,Title24 CFR, Part3280, inthe United States,or whensuch a standardis notapplicable,ANSI/NCSBCS A225.1/NFPA501A, Manufactured Home InstallationsStandard orANSI A119.2 ou NFPA501C Standard for RecreationalVehicles This appliance is only foruse with the type of gas indicated on therating plateand may be installed inan aftermarket, permanently located, manufactured (mobile) home where notprohibited bylocal codes. See owner's manualfor details.This appliance is notconvertible foruse with othergases, unlessa certified kitis used.(Kit #576-972).

Fan Part# 576-917. Installer l'appareilselon lescodes ou règlementslocaux, ou,en l'absence detels règlements,selon les codesd'installation ANSIZ223.1, NationalFuel Gas Codeou CSA-B149.1en vigueur. Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCSA225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSIA119.2 ou NFPA 501C Standard for Recreational Vehicles. Cet appareildoit êtreutilize uniquement avec le typede gazindiqué surla plaque signalétique. Cet appareilpeut êtreinstallé dans une maison préfabriquée ou mobile(É.-U. seulement)installée à demeure si les règlements locauxle permettent.Voir lanotice de l'utilisateurpour plusde renseignements. Cetappareil nepeut pas êtreutilisé avecd'autres gaz saufsi unetrousse de conversioncertifiée estfournie.

This ventedgas fireplaceheater is notfor usewith air filters. Ne pasutiliser defiltre à airavec cefoyer au gazà évacuation. FOR USEWITH GLASSDOORS CERTIFIED WITHTHE APPLIANCEONLY

Electrical supply/Électrique 115VAC, 1.13 A, 60Hz. NOT FOR USE WITH SOLID FUELS. /

WC/C.E.

11" (2.74 kPa)

WC/C.E.

10" (2..49 kPa)

WC/C.E.

6.4" (1.60 kPa) #51 DMS 25,000 Btu/h (7.33 kW) 31 ,000 Btu/h (9.09 kW) 0-4500 ft/pi (0-1372 m)

NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.

CANADA and U.S.A.

APPAREIL FONCTIONNANT AU NATURAL GAS CONCU POUR ETRE POELE: Mod le B36XTCE-NG

Pression d'allimentation minimum Pression à la tubulure d' chappement lev e Pression à la tubulure d' chappement basse Grandeur de l'injecteur D bit minimum selon D bit maximum selon l'altitude

ÉÉ

CONCU POUR ETRE POELE: Mod le B36XTCE-LP

Pression d'allimentation minimum Pression à la tubulure d' chappement lev e Pression à la tubulure d' chappement basse Grandeur de l'injecteur D bit minimum selon D bit maximum selon l'altitude

FOYER AU GAZ À ÉVACUATION

ééé é

Calorifique

QUIP A L'UISINE POUR GAZ PROPANE

ééé é

Calorifique

POUR UTILISATION UNIQUEMENTAVECLES PORTESEN VERRE CERTIFIÉESAVECL'APPAREIL

FPI Fireplace Products International Ltd. Delta, BC, Canada

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

Minimum Clearances to Combustibles /

Degagement Minimum De Materiaux Combustibles

Ceiling

Floor

DOOR SEAL: Please

check that the door is

properly sealed

(See Instruction Manual for

detailed instructions)

410

Serial No./ No de serie

410

0" Clearance to combustibles from:

Sides, bottom and rear of unit *Top - 3-1/2" (89mm) non-combustible

Wall

material required above unit.

Mantel Clearances from

Fireplace Opening:

(A) Min. 15-1/2" (394mm)

Side Wall Clearance from Fireplace Opening

B) Min. 12” (305mm)

Ceiling from Top of Fireplace Opening:

C) 39” (991mm)

Mantel Depth:

D) Max. 12” (304mm)

Alcove Clearances:

E) Min. Width 84" (2134mm), F) Max. Depth 36" (914mm)

Made in Canada/ Fabrique au Canada

(on one side)

919-153

For the State of Massachusetts, installation and repair must be done by a plumber or gas ﬁ tter licensed in the Commonwealth of Massachusetts.

For the State of Massachusetts, ﬂ exible connectors shall not exceed 36 inches in length.

For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.

The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with battery back up in the same room where the gas appliance is installed.

Regency B36XTCE Gas Fireplace

REQUIREMENTS

5.08: Modifications to NFPA-54, Chapter 10

(2) Revise 10.8.3 by adding the following additional requirements:

(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

MA Code - CO Detector

(for the State of Massachusetts only)

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL

OBSTRUCTIONS".

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:

1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and

2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

Regency B36XTCE Gas Fireplace

23-5/8"

(599mm)

40-5/16"

(1024mm)

33"

(838mm)

40-5/8"

(1032mm)

UNIT DIMENSIONS

14-3/4"

3(375mm)

DIMENSIONS

21-13/16"

(529mm)

29-7/8"

(759mm)

32-7/8"

(759mm)

25-5/8"

(650mm)

4-1/8"

(105mm)

38-1/16"

8-5/8"

41-5/16"

(1049mm)

29-3/4"

(219mm)

(756mm)

(188mm)

3-1/4"

(79mm)

7-7/16"

1-1/2

(38mm)

1-1/4"

(32mm)

35-5/16'

33-1/8"

(840mm)

(895mm)

Regency B36XTCE Gas Fireplace

INSTALLATION

IMPORTANT MESSAGE

SAVE THESE

INSTRUCTIONS

The B36XTCE Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁ rst. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this ﬁ replace is installed in compliance with manufacturers instructions and all applicable codes.

BEFORE YOU ST ART

Safe installation and operation of this appliance requires common sense, however, we are required by the Canadian Safety Standards and ANSI Standards to make you aware of the following:

INSTALLATION AND REPAIR SHOULD BE DONE BY AN AUTHORIZED SERVICE PERSON. THE APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING MATERIAL, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE AND DRAPERIES.

WARNING: FAILURE TO INSTALL THIS APPLIANCE CORRECTLY WILL VOID YOUR WARRANTY AND MAY CAUSE A SERIOUS HOUSE FIRE.

YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN AND OTHERS MAY BE SUSCEPTIBLE TO ACCIDENTAL CONTACT BURNS. A PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL IN THE HOUSE. TO RESTRICT ACCESS TO A FIREPLACE OR STOVE, INSTALL AN ADJUSTABLE SAFETY GATE TO KEEP TODDLERS, YOUNG CHILDREN AND OTHER AT RISK INDIVIDUALS OUT OF THE ROOM AND AWAY FROM HOT SURFACES.

CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT BE PLACED ON OR NEAR THE APPLIANCE.

ANY SAFETY SCREEN, GUARD, OR BARRIER REMOVED FOR SERVICING THE APPLIANCE, MUST BE REPLACED PRIOR TO OPERATING THE APPLIANCE.

IF THE BARRIER BECOMES DAMAGED, THE BARRIER SHALL BE REPLACED WITH THE MANUFACTURER'S BARRIER FOR THIS APPLIANCE.

GENERAL SAFETY

INFORMATION

1) The appliance installation must conform with

local codes or, in the absence of local codes, with the current Canadian or National Gas Codes, CAN1-B149 or ANSI Z223.1 Installation Codes.

2) The appliance when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the current National Electrical Code, ANSI/NFP A 70 or CSA C22.1 Canadian Electrical Code.

7) Any safety glass removed for servicing must be replaced prior to operating the appliance.

8) To prevent injury, do not allow anyone who is unfamiliar with the operation to use the ﬁ replace.

9) Wear gloves and safety glasses for protection while doing required maintenance.

10) Be aware of electrical wiring locations in walls and ceilings when cutting holes for termination.

11) Under no circumstances should this appliance be modiﬁ ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.

12) Installation and any repairs to this appliance should be done by a qualiﬁ ed service person. A professional service person should be called to inspect this appliance annually. Make it a practice to have all of your gas appliances checked annually.

13) Do not slam shut or strike the glass door.

14) Under no circumstances should any solid fuels

(wood, paper, cardboard, coal, etc.) be used in this appliance.

15) The appliance area must be kept clear and free of combustible materials, (gases and other ﬂ ammable vapours and liquids).

Emissions from burning wood or gas could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.

3) See general construction and assembly instructions. The appliance and vent should be enclosed.

4) This appliance must be connected to the speciﬁ ed vent and termination cap to the outside of the building envelope. Never vent to another room or inside a building. Make sure that the vent is ﬁ tted as per Venting instructions.

5) Inspect the venting system annually for blockage and any signs of deterioration.

6) Venting terminals shall not be recessed into a wall or siding.

Regency B36XTCE Gas Fireplace

INSTALLATION

CHECKLIST

1) Locate appliance

a) Room location (Refer to "Locating Your

Gas ﬁ replace" section)

b) Clearances to Combustibles (Refer to

"Clearances" section)

c) Mantle Clearances (Refer to "Combustible

Mantel Clearances" section)

d) Framing & Finishing Requirements (Refer

to "Framing & Finishing" section)

e) Venting Requirements (Refer to "V enting"

section)

2) Assemble Top Standoffs and Top Facing Support and Side Nailing Strips (Refer to "Unit Assembly Prior to Installation" Section). NOTE: Must be done before installing unit into place.

3) Install vent (Refer to "Venting" sections).

4) Make gas connections. Test the pilot. Must

be as per Diagram (Refer to "Pilot Adjustment " section).

Convert to propane if desired (Refer to "Gas

Line Installation" and "Conversion Kit from NG to LPG" sections).

5) Make electrical connections to receptacle supplied with unit (recommended).

This includes:

1) Clocking the appliance to ensure the correct

ﬁ ring rate (rate noted on label 31,000 Btu/h, after burning appliance for 15 minutes.

2) If required, adjusting the primary air to ensure that the ﬂ ame does not carbon. First allow the unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that causes sooting or carboning that results in damage is not the responsibility of the manufacturer.

LOCATING YOUR

GAS FIREPLACE

1) When selecting a location for your ﬁ replace,

ensure that the clearances are met.

2) The appliance must be installed on a ﬂ at, solid, continuous surface For example a wood, metal or concrete ﬂ oor or in a raised (on the wall) application. The appliance must be installed on a metal or wood panel extending the full width and depth of the appliance.

3) The B36XTCE Gas Fireplace can be installed in a recessed position or framed out into the room as in A, B, C and D. See Diagram 1.

4) This appliance is Listed for bedroom installations using the standard Remote (millivolt thermostat system). Some areas may have further requirements, check local codes before installation.

5) The B36XTCE Gas Fireplace are approved for alcove installations, see "Clearances" section for details.

6) We recommend that you plan your installation on paper using exact measurements for clearances and floor protection before actually installing this appliance. Have an authorized inspector, dealer, or installer review your plans before installation.

Note: For vent terminations refer to

"Exterior Vent T ermination Locations" section.

6) Install standard and optional features. Refer

to the following sections:

a. Install 4AA batteries into battery pack or

install optional AC power adaptor b. Inner Panels or Brick Panels (Optional) c. Log Set Installation d. Standard Flush Door e. Remote Control f. Wall Switch g. Wall Thermostat h. Fan Installation (Optional) i. Light Installation (Optional)

7) Final check.

Diagram 1

A) Flat on Wall B) Flat on Wall Corner C) Recessed into Wall/Alcove D) Corner

Regency B36XTCE Gas Fireplace

INSTALLATION

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ﬁ res is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this ﬁ replace and vent system be installed only in accordance with these instructions.

The top, back and sides of the ﬁ replace are deﬁ ned by

Caution Requirements

standoffs. The metal ends of the standoff may NOT be

recessed into combustible construction.

B36XTCE Clearance Requirements

Clearance: Dimension Measured From:

A: Mantel Height (min.) 15-1/2" (394mm) Top of Fireplace Opening B: Sidewall 12" (304mm) one side

C: Ceiling 39" (991mm) Top of Fireplace Opening D: Mantel Depth (max.) 12" (304mm) 23-1/2 " (570mm) from

E: Alcove Width 84" (2134mm) Wall to Wall (Minimum) F: Alcove Depth 36" (914mm) Front to Back Wall (Maximum) Notes: 0" No Hearth Required

Fire hazard is an extreme risk

WARNING

if these clearances (air space) to combustible materials are not

adhered to. It is of greatest importance that this ﬁ replace and vent

system be installed only in accordance with these instructions.

Side of Fireplace Opening

only

Top of Fireplace Opening

Minimum Vent Clearances

Close to Ceiling

to Combustibles

Alcove

Horizontal Top 2" (51mm) Horizontal Side 1-1/2 " (38mm) Horizontal Bottom 1-1/2" (38mm) Vertical Vent 1-1/2" (38mm)

Regency B36XTCE Gas Fireplace

INSTALLATION

MANTEL CLEARANCES

Due to the extreme heat this ﬁ replace emits, the mantel clearances are critical. Combustible mantel clearances from top of front facing are shown in

the Diagram on the right.

Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board.

Mantel Clearances

810

12”

Inches

To Floor

Mantel Clearances B36XTCE

From Top of Fireplace Opening

Combustible

7”

Non-combustible

Header

(steel stud)

on edge

3-1/2”

Non-combustible

Standoff

Top of

29-11/16"

(754mm)

Fireplace

Opening

ABCD

23-1/2"

(597mm)

20"

(508mm)

15-1/2"

(394mm)

Note: Ensure the paint that is used on the mantel and the facing is "High Quality" or the paint may discolour.

Regency B36XTCE Gas Fireplace

INSTALLATION

MANTEL LEG CLEARANCES

Top View

Side opening of fireplace

Mantel leg

1-1/2"

Mantel leg

3.5”

6.5"

Allowable mantel leg

projection.

12"

NON- COMBUSTIBLE REQUIREMENTS:

40-5/8"

[1031mm]

Non combustible - supplied w/unit

No Combustible

Materials in this Area

3-1/2"

[89mm]

8-3/8"

[213mm]

[1057mm]

25-5/8"

41-5/8"

NO FACING OR

[651mm]

FINISHING MATERIAL

IN THIS AREA

4-1/8"

[105mm]

32-7/8"

3-7/8"

[98mm]

NOTE: The 3-1/2" x 40-5/8" non combustible material supplied with this unit can be replaced if trying to achieve a clean ﬁ nish. A large piece of non

combustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.

835mm

See framing dimensions on next page.

Regency B36XTCE Gas Fireplace

INSTALLATION

FRAMING

Framing Dimensions Description B36XTCE

L Framing rise from ﬂ oor

M Framing Width 41-1/4"(1048mm) N Framing Height 42" (1067mm) O (Rear Vent) Framing Depth - Rear Vent 23-7/8" (606mm) O (Top Vent) Framing Depth - Top Vent 23-7/8" (606mm) P (Top Vent) Corner Facing Wall Width 53-1/4" (1353mm) P (Rear Vent) Corner Facing Wall Width 57-7/8" (1470mm) AstroCapXL

Q (Top Vent) Corner Facing Wall Width 75-1/4" (1911mm) Q (Rear Vent) Corner Facing Wall Width 81-1/2" (2070mm) AstroCapXL

R (Rear Vent) Framed Chase Ceiling - Rear 41-1/2" (1054mm) R (Top Vent) Framed Chase Ceiling - Top 50-1/2" (1283mm) S (Rear Vent) Vent Centerline Height - Rear 26-1/2" (673mm) S (Top Vent) (5" x 8") Vent Centerline Height - Top 42-1/8" (1070mm) Flex 44-1/4" (1123mm) Rigid S (Top Vent) (4" x 6-5/8") Vent Centerline Height - Top - 49" (1245mm) Rigid T Gas Connection Height 1-1/2" (38mm) U Gas Connection Inset 7-3/8" (187mm) V Gas Connection Width 3-1/4" (82mm) W Non-combustible Height 3-1/2"" (89mm)

0" (when not using a surround)

1" min (when using Mantel)

66-1/8" (1670mm) - other approved caps

93-1/2" (2375mm) - other approved caps

** Important: Framing height requires consideration of the hearth depth. Dimension N = N + the thickness of the installed hearth.

Drywall

Non-combustible

Header

(steel stud

on edge)

(or other

facing)

Non-Combustible

Header

(steel stud) on edge

Non-Combustible Facing

11" (279mm)

dia. Hole through

wall Vent.

Regency B36XTCE Gas Fireplace

Opening for gas

connection

INSTALLATION

FRAMING & FINISHING

1. Frame in the enclosure for the unit with framing material.

Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.

2. For exterior walls, insulate the enclosure to the same degree as the rest of the house; apply vapour barrier and drywall, as per local installation codes. (Do not insulate the ﬁ replace itself.)

WARNING: Failure to insulate and add vapor barriers to the inside of the exterior wall will result in operational and performance problems

including, but not limited to: excessive condensation on glass doors, poor ﬂ ame package, carbon, blue ﬂ ames etc. These are not product related issues.

3. The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances"

section. Combustible materials can be laid against the side and back standoffs and the stove base.

4. Tile Finish Option 1: Drywall may be installed onto the unit as shown below to create a surface to apply ﬁ nishing materials such as tile, slate, etc.

Drywall cannot extend beyond the metal surface of the unit.

5. Tile Finish Option 2: If applying a non-combustible ﬁ nishing material (tile,slate,etc) the material can be installed directly onto the metal surface (clean front) of the unit in the area shown below.

TILE FINISH

Combustible Material

Non-combustible

Finishing Material (ie. tile)

Non-combustible Material (3-1/2" x 40-5/8")

Nailing Strip

-1/2" back from unit face

Supplied with Unit

[651mm]

32-7/8"

835mm

25-5/8"

Ensure finished material is brought to lip

Non-combustible Finishing Material (ie. tile)

1-1/2

Combustible Material

CLEAN FINISH

6. If applying a non-combustible facing it may be installed over the metal surface (clean front) of the unit in the area shown below.

NON-COMBUSTIBLE BOARD - SUPPLIED WITH UNIT

41-5/8"

[1054mm]

Combustible and Non-combustible Facing and Finishing

40-5/8"

[1032mm]

Materials around unit.

WOOD STUD

1/2" DRYWALL

DO NOT EXTEND DRYWALL ONTO METAL SURFACE OF UNIT.

NON-COMBUSTIBLE FACING

FOR CLEAN LOOK (ie. painted finish)

1/2" DRYWALL

Non-combustible Finishing Material

Ensure finished material is brought to lip

Non-combustible Finishing Material

Combustible

Material

Non-combustible Material (3-1/2" x 40-5/8")

Nailing Strip

1-1/2

Combustible Material

(38mm)

Supplied with Unit

-flush with unit

(38mm)

NOTE: The 3-1/2" x 40-5/8" non combustible material supplied with this unit can be replaced if trying to achieve a clean ﬁ nish. A large piece of non com-

bustible material (ie. 4' x 8' x 1/2") can be used to eliminate taped seams on or near unit.

Regency B36XTCE Gas Fireplace

INSTALLATION

7. Non-combustible material (ie. tile, slate, etc) may be brought up to the edge of the glass door of the unit. Minimum clearances must be adhered to, this

will assure ease of glass door removal and access to the lower panel.

NOTE: Non-combustible ﬁ nishing materials may be of any thickness desired.

40-5/8"

[1031mm]

Non combustible - supplied w/unit

No Combustible

Materials in this Area

NO FACING OR

3-1/2"

[89mm]

8-3/8"

[213mm]

[651mm]

25-5/8"

[1057mm]

41-5/8"

FINISHING MATERIAL

IN THIS AREA

4-1/8"

[105mm]

32-7/8"

3-7/8"

[98mm]

Minimum Clearances for Finishing Materials

835mm

IMPORTANT FINISHING DETAIL NOTE:

Before placing unit into ﬁ nal position - it is important to know the total thickness / height of ﬁ nished hearth (tile, carpet, etc.) The base of the ﬁ replace, 4 sided faceplate or mantel should be level or higher than the ﬁ nished hearth height.

Note: All non-combustible facing material should butt up cleanly

Rough edges may be visible from an angle.

To maintain a clean ﬁ nished edge - facing material edges

may be ﬁ nished with a J-style trim or metal cornerbead (both materials available at your local building or hardware store).

No Combustible

Materials in this Area

J Style trim or metal corner bead may be used to finish edges

32-7/8"

835mm

Trim materials

to the ﬂ anges around the ﬁ rebox opening.

[651mm]

25-5/8"

IMPORTANT: Materials used must be NON-COMBUSTIBLE.

Regency B36XTCE Gas Fireplace

INSTALLATION

UNIT ASSEMBLY PRIOR TO INSTALLATION

BEFORE YOU ST ART

The T op Nailing Support, the Side Nailing Strips, the 2 Top Standoffs and the Flue Collar must be correctly positioned and attached before the ﬁ replace is moved into position.

TOP STANDOFF ASSEMBLY

The top standoffs are shipped in a ﬂ at position and must be folded into shape and attached.

STANDOFF SLOT LOCATION

TopView

1) Take each standoff and bend into the correct shape. Bend up at the bend lines until the tab in the standoff and the pre-punched slots on the ﬁ replace top line up. Be sure to use correct slots, they are marked.

NAILING STRIPS

1. There are 8 (eight) side nailing strips and one top nailing strip available on the unit. One set of four (4) are for a clean ﬁ nish installation, the other set are

for a tile ﬁ nish installation as they are set back 1/2" (13mm). The top nailing strip is adjustable to 1/2" (13mm).

2. Bend the required four (4) nailing strips to 90º.

3. Attach top nailing strip with one (1) screw (located at the back of the nailing strip). Adjust to required position, flush or back 1/2" and tighten screw.

Adjustable Top

Nailing Strip

Nailing strip for

Clean Finish (set

ﬂ ush with unit)

Nailing strip for

Tile Finish (set

back 1/2")

B36XT/ B36XTE/ B36XTCE

B36X B36X

B36XT/ B36XTE/ B36XTCE

Nailing strip for

Tile Finish (set

back 1/2")

Nailing strip for

Clean Finish (set

ﬂ ush with unit)

Regency B36XTCE Gas Fireplace

INSTALLATION

Intake Collar Assembly

w/gasket

The unit comes equipped as a rear vent unit. These instructions are to be used, only if the unit is going to be top vented.

Top Collar Assembly Kit

1 Intake Collar Assembly with Gasket 1 Intake Cover Plate with Gasket 1 Top/Rear Exhaust Assembly with Gasket 1 Heat Deﬂ ector 1 Bafﬂ e Plate 29 1/4" x 1/2" Screws (4 spares) 1 Restrictor 1 Intake Collar Gasket (spare) 1 Exhaust Assembly Gasket (spare)

1 Insulation Plate Cover 1 Insulation Filling

1) Remove the door assembly by releasing the adjustable latches and lifting up off the door frame assembly.

Note: This conversion must be done prior to the unit being placed in position.

Exhaust Assembly

w/ gasket

Intake Collar Assembly

w/gasket

Insulation cover

plate

Note: Components shown are installed on unit.

CONVERSION TO TOP VENT

Intake Cover Plate

w/gasket

Insulation ﬁ lling

Adjustable Tension

Latch location

2) From inside the ﬁ rebox, remove the top heat deﬂ ector by removing 2 screws.

Heat Deﬂ ector

Diagram 2

3) From inside the ﬁ rebox, remove the bafﬂ e plate by removing 4 screws

- remove top front screw ﬁ rst. See Diagram 3.

Bafﬂ e Plate

Diagram 3

Regency B36XTCE Gas Fireplace

Diagram 1

4) From the inside of the ﬁ rebox, remove the exhaust assembly by removing the 8 screws. See Diagram 4.

Diagram 4

INSTALLATION

5) From the outside rear of the ﬁ rebox, remove the intake collar assembly. Remove the 4 - 1/4" x 1/2" screws. See Diagram 5.

Diagram 9

Exhaust

Assembly

Intake Collar

Assembly

Diagram 5

6) From the outside top of the ﬁ rebox - remove top insulation cover plate and insulation ﬁ lling - by removing 4 screws. See Diagram 6.

Discard cover plate and insulation ﬁ lling.

Diagram 6

7) From the outside top of the ﬁ rebox - remove the intake cover plate by removing the 4 - 1/4" x 1/2 " screws. See Diagram 7.

9) From the outside top of the ﬁ rebox, install the intake collar assembly . Secure with 4 - 1/4" x 1/2" screws. Ensure all screws are tight, but do not over tighten. All 4 screws must be used.

Exhaust

Assembly

Diagram 10

10) From the outside rear of the ﬁ rebox, install the intake cover plate with 4 - 1/4" x 1/2" screws. Ensure all screws are tight, but do not over tighten. All 4 screws must be used.

Intake Collar

Assembly

Diagram7

Before proceeding to Step 8, inspect condition of all gaskets. DO NOT install parts with damaged gaskets. Replace if necessary

with spare gaskets supplied.

8) From the inside of the ﬁ rebox, place the exhaust assembly into position as shown in Diagram 8 and secure with 8 - 1/4" x 1/2" screws (Diagram 9). Ensure all screws are tight, but do not over tighten.

All 8 screws must be used.

Diagram 8

Diagram 11

11) Set vent restrictor accordingly - see next page.

12) From inside the ﬁ rebox, re-install the bafﬂ e plate and heat

deﬂ ector - reverse steps 2 & 3.

VENTING

INTRODUCTION

The B36XTCE uses the "balanced ﬂ ue" technology Co-Axial sys- tem. The inner liner vents products of combustion to the outside while the outer liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These ﬂ ue pipes must not be connected to any other

appliance.

The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.

Regency B36XTCE Gas Fireplace

INSTALLATION

VENT RESTRICTOR, BAFFLE & HEAT DEFLECTOR INSTALLATION

NOTE: THE VENT RESTRICTOR & BAFFLE MUST BE INSTALLED PRIOR TO OPTIONAL PANEL INSTALLATION.

1) Determine the venting conﬁ guration.

2) Remove top heat deﬂ ector and bafﬂ e plate (reverse of steps 5 & 6).

3) Go to venting arrangements section (in the manual) to determine if

a vent restrictor setting is required.

Note: The vent restrictor does not apply to rear vent applications.

4) Align the vent restrictor plate to the required vent restrictor position

as per the Diagrams shown.

5) Once the vent restrictor plate is in the required position, secure with 2 - 1/4" x 1/2" screws. Ensure all screws are tight, but do not over

tighten. (See Diagram 2).

Diagram 2 Vent restrictor installed on top exhaust assembly

6) From inside the ﬁ rebox, install the bafﬂ e plate with 4 - 1/4" x 1/2 " screws. Ensure all screws are tight, but do not over tighten.

Bafﬂ e Plate

Note: If installing brick/optional panels, see brick/optional panel

instructions before proceeding to next step.

7) From inside the ﬁ rebox, install the top heat deﬂ ector with 2 -

1/4" x 1/2" screws. Ensure all screws are tight, but do not over

tighten.

Heat Deﬂ ector

Diagram 3

Diagram 4

Regency B36XTCE Gas Fireplace

INSTALLATION

EXTERIOR VENT TERMINATION REQUIREMENTS

Minimum Clearance Requirements

A Clearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)

B Clearance to window or door that may be opened 12"(30cm) 9" (23cm)

C Clearance to permanently closed window **

D Vertical clearance to ventilated sofﬁ t located above the terminal within a horizontal distance of 2 feet (61cm)

from the center line of the terminal (check with the local code)

E Clearance to unventilated sofﬁ t 19"(48cm) 19"(48cm)

F Clearance to outside corner: with AstroCap Termination Cap. 13"(33cm) 13"(33cm)

Clearance to outside corner: with all other approved Termination Caps. 13"(33cm) 13"(33cm)

G Clearance to inside corner: with AstroCap Termination Cap 11"(28cm) 11"(28cm)

Clearance to inside corner: with all other approved Termination Caps. 11"(28cm) 11"(28cm)

H Clearance to each side of center line extended above meter/regulator assembly 36"(90cm)

J Clearance to service regulator vent outlet 36"(90cm) *

K Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)

L Clearance to a mechanical air supply inlet #3' (91cm) above if within 10' (3m) horizontally. 72"(1.8m) 36"(90cm)

M Clearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)

N Clearance under veranda, porch, deck, or balcony 12"(30cm)

In accordance with current CSA B149.1, Natural Gas and Propane Installation Code

In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code

┼

A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings

‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂ oor

Clearance in accordance with local installation codes and the requirements of the gas supplier

3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly

3 feet (91cm) above - if within 10 feet (3m) horizontally

Canada

24"(60cm) 24"(60cm)

┼

‡

USA

Regency B36XTCE Gas Fireplace

INSTALLATION

4" X 6-5/8" RIGID PIPE

CROSS REFERENCE CHART ONLY

Components from different Manufacturers may not be mixed. Not all Rigid Pipe components are available directly from FPI.

Description

6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6

6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B

7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A

7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A

9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A N/A

9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A N/A

12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1

12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B

18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18

18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B

24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2

24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B

36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3

36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B

48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4

48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B

60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A

60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A

Simpson

Direct Vent Pro

Selkirk

Direct Temp™

American Metal

Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT

Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB

Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A

Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A

Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A

Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A

Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 N/A

Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 N/A

Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A

Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A

45º Elbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45

45º Elbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B

45º Elbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A

45º Elbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A

90º Elbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90

90º Elbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B

90º Elbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A

90º Elbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A

90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A

Adaptor* N/A N/A N/A 4D90L N/A N/A

Ceiling Support N/A 4DT-CS 4DFSP 4DSP SV4SD TE-4DE45

Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TE-4DE45B

Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM N/A

Offset Support

Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM TE-4DE90

Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF TE-4DE90B

Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF N/A

Trim Plate-Black N/A 4DT-TP 4DFPB 4DCP SV4LA N/A

46DVA-ES (N/A - FPI)

4DT-OS N/A N/A SV4SU N/A

Regency B36XTCE Gas Fireplace

INSTALLATION

Description

Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A

Attic Insulation Shield -

Basic Horizontal Termination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK N/A

Horizontal Termination Kit (B) 46DVA-KHA

Vertical Ter mination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A

High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT

High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT

Horizontal Square Termination Cap See

Vertical Ter mination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 TM-4VT

Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC

Adjustable Flashing 0/12-6/12 46DVA-F6 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA

Adjustable Flashing 6/12-12/12 46DVA-FLA 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB

Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS

Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A

Snorkel Termination 14” 46DVA-SNKL N/A N/A N/A N/A TM-4ST14

Snorkel Termination 36” N/A N/A N/A N/A N/A TM-4ST36

Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS

Simpson

Direct Vent Pro

(Changed Components)

46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT

Selkirk

Direct Temp™

4DT-HKB 4DHTK1 4DHTKB SV-HK N/A

American Metal

Products®

Amerivent Direct

Metal-Fab™

Sure Seal

Security

Secure- Vent®

ICC Excel

Direct

Restrictor Disk N/A N/A N/A N/A N/A TM-4DS

Extended Vertical Ter mination Cap N/A N/A N/A N/A N/A N/A

Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6

Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7

Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8

Chimney Conversion Kit Masonry (USA only)

Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR

Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A

FPI

946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Terminal

510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Terminal

640-530/P Riser Vent Terminal 946-523/P AstroCap Horizontal Cap

946-605 Starter Collar Increaser 4” x 6-5/8” to 5” x 8” 946-206 Vinyl Siding Standoff for AstroCap

Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).

Offset Pipe Selection: Use this table to determine offset pipe lengths.

Pipe Length

(L)

0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com

6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com

9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com

12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com

24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com

36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com

48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)

Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination. Never allow the vent to run downward - this could cause high temperatures and may present a possible ﬁ re hazard.

Run (X) Rise (Y)

46DVA-KMC N/A N/A N/A N/A N/A

4” x 6-5/8” Venting For speciﬁ c instructions on venting components - visit the

manufacturers website listed below.

Regency B36XTCE Gas Fireplace

INSTALLATION

5" X 8" RIGID PIPE

CROSS REFERENCE CHART ONLY

Components from different Manufacturers may not be mixed. Not all Rigid Pipe components are available directly from FPI.

Description

6” Pipe Length-Galvanized 58DVA-06 5DT-6 5D6 TC-5DL6

6” Pipe Length-Black 58DVA-06B 5DT-6B 5D6B TC-5DL6B

9” Pipe Length-Galvanized 58DVA-09 5DT-9 N/A N/A

9” Pipe Length-Black 58DVA-09B 5DT-9B N/A N/A

12” Pipe Length-Galvanized 58DVA-12 5DT-12 5D12 TC-5DL1

12” Pipe Length-Black 58DVA-12B 5DT-12B 5D12B TC-5DL1B

18” Pipe Length-Galvanized 58DVA-18 5DT-18 5D18 TC-5DL18

18” Pipe Length-Black 58DVA-18B - N/A from FPI 5DT-18B 5D18B TC-5DL18B

24” Pipe Length-Galvanized 58DVA-24 5DT-24 5D24 TC-5DL2

24” Pipe Length-Black 58DVA-24B 5DT-24B 5D24B TC-4DL2B

36” Pipe Length-Galvanized 58DVA-36 5DT-36 5D36 TC-5DL3

36” Pipe Length-Black 58DVA-36B 5DT-36B 5D36B TC-5DL3B

48” Pipe Length-Galvanized 58DVA-48 5DT-48 5D48 TC-5DL4

48” Pipe Length-Black 58DVA-48B 5DT-48B 5D48B TC-5DL4B

60” Pipe Length-Galvanized 58DVA-60 N/A N/A N/A

60” Pipe Length-Black 58DVA-60B - N/A from FPI N/A N/A N/A

Adjustable Length 3”-10”-Galvanized N/A N/A 5DAL TC-5DLT

Adjustable Length 3”-10”-Black N/A N/A 5DALB TC-5DLTB

Adjustable Length 11”-14” -Galvanized Disc. - See 58DV-08A 5DT-AJ N/A N/A

Adjustable Length 11”-14” -Black Disc. - See 58DV-08B 5DT-AJB N/A N/A

Extension Pipe 17”-24” -Galvanized Disc. - See 58DV-16A N/A N/A N/A

Extension Pipe 17”-24” -Black Disc. - See 58DV-16AB N/A N/A N/A

Adjustable Length 8-1/2”-Galvanized 58DVA-08A - N/A from FPI N/A N/A N/A

Adjustable Length 8-1/2”-Black 58DVA-08AB N/A N/A N/A

Extension Pipe 16”-Galvanized 58DVA-16A - N/A from FPI N/A N/A N/A

Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A

Simpson

Direct Vent Pro

Selkirk

Direct Temp™

Metal-Fab™

Sure Seal

ICC Excel

Direct

45º Elbow-Galvanized 58DVA-E45 5DT-EL45 5DT-EL45 TE-5DE45

45º Elbow-Black 58DVA-E45B 5DT-EL45B 5DT-EL45B TE-5DE45B

45º Elbow Swivel-Galvanized

45º Elbow Swivel-Black

90º Elbow-Galvanized 58DVA-E90 5DT-EL90S 5DT-EL90S TE-5DE90

90º Elbow-Black 58DVA-E90B 5DT-EL90SB 5DT-EL90SB TE-5DE90B

90º Elbow, Swivel-Galvanized

90º Elbow, Swivel-Black

90º Starter Elbow, Swivel-Galvanized N/A N/A N/A N/A

Adaptor* N/A N/A N/A N/A

Ceiling Support 58DVA-DC 5DT-CS 5DSP TE-5DE45

Cathedral Support Box 58DVA-CS 5DT-CSS 5DRS TE-5DE45B

Wall Support/Band 58DVA-WS 5DT-WS/B 5DWS N/A

Offset Support

Wall Thimble-Black 58DVA-WT 5DT-WT 5DWT TE-5DE90

Wall Thimble Support/Ceiling Support 58DVA-DC

Firestop Spacer 58DVA-FS 5DT-FS 5DFS N/A

Trim Plate-Black 58DAV-WFS 5DT-TP 5DCP N/A

Disc. - See 58DVA-E45

Disc.-See 58DVA-E45B

Disc. - See 46DVA-E45

58DVA-ES - N/A from FPI

- N/A from FPI N/A N/A TE-5DE90B

N/A N/A N/A

5DT-OS N/A N/A

Regency B36XTCE Gas Fireplace

INSTALLATION

Description

Attic Insulation Shield 12” 58DVA-IS N/A from FPI N/A N/A N/A

Basic Horizontal Termination Kit (A) N/A 5DT-HKA N/A N/A

Horizontal Termination Kit (B) 58DVA-KHA 5DT-HKB N/A N/A

Vertical Ter mination Kit 58DVA-VHA 5DT-VKC N/A N/A

High Wind Vertical Cap 58DVA-VCH N/A N/A TM-5VT

High Wind Horizontal Cap N/A N/A N/A TM-5DHT

Horizontal Square Termination Cap N/A 5DT-HHC 5DHT TM-5HT

Vertical Ter mination Cap N/A 5DT-HVC 5DVT TM-5VT

Storm Collar 58DVA-SC 5DT-SC 5DSC TM-SC

Adjustable Flashing 0/12-6/12 58DVA-F6 5DT-AF6 5DF TF-5FA

Adjustable Flashing 6/12-12/12 58DVA-F12 5DT-AF12 5DF1-2 TF-5FB

Vinyl Siding Standoff 58DVA-VSS 5DT-VS 5DVS TM-VSS

Vinyl Siding Shield Plate N/A 5DT-VSP N/A N/A

Snorkel Termination 14” 58DVA-SNK14 N/A N/A TM-5ST14

Snorkel Termination 36” 58DVA-SNK36 (N/A - FPI) N/A N/A TM-5ST36

Restrictor Disk 58DVA-RD N/A N/A TM-5DS

Colinear Flex Connectors N/A N/A N/A N/A

Simpson

Direct Vent Pro

Selkirk

Direct Temp™

Metal-Fab™

Sure Seal

ICC Excel

Direct

FPI

946-604/P Simpson Direct Vent -Vent Guard (Optional) 946-623/P AstroCap XL Horizontal Cap

770-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-506/P Vent Guard (Optional)

946-606 Starter collar reducer 5” x 8” to 4” x 6-5/8” 946-625 Vinyl Siding Standoff - AstroCap XL

Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).

Offset Pipe Selection: Use this table to determine offset pipe lengths.

Pipe Length

(L)

0” (0mm) 5-11/16” (144mm) 15-5/16” (389mm) Simpson Direct Vent Pro: www.duravent.com

6” (152mm) 8-13/16” (224mm) 18-7/16” (468mm) Selkirk Direct-Temp: www.selkirkcorp.com

9” (229mm) 10-15/16” (278mm) 20-9/16” (522mm) Metal-Fab Sure Seal: www.mtlfab.com

12” (305mm) 13” (330mm) 22-11/16” (576mm) Industrial Chimney Company: www.icc-rsf.com

24” (610mm) 21-7/16” (697mm) 31-1/16” (789mm) Note: Horizontal runs of vent must be level, or have a 1/4”

36” (914mm) 29-13/16” (757mm) 39-7/16” (1002mm)

48” (1219mm) 38-1/4” (972mm) 47-7/8” (1216mm)

5” x 8” Venting For speciﬁ c instructions on venting components - visit the

Run (X) Rise (Y)

manufacturers website listed below.

rise for every 1 foot of run towards the termination. Never allow the vent to run downward - this could cause high temperatures and may present a possible ﬁ re hazard.

Regency B36XTCE Gas Fireplace

INSTALLATION

648

VENTING ARRANGEMENTS FOR HORIZONTAL TERMINATIONS

FLEX VENT OR RIGID PIPE 5" X 8"

The Diagrams show all allowable combinations of vent runs with 5" x 8" venting using the Regency direct vent system or rigid vent system. A vent guard should be used whenever the termination is lower than the speciﬁ ed minimum or as per local codes.

For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum continuous vent length of 3ft (0.9m).

Note: Must use optional rigid pipe adaptor (Part # 770-994) when using Rigid Pipe vent systems.

• Maintain clearance to combustibles.

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

Horizontal (Feet)

Vertical Height (Feet)

Factory Setting - No Restrictor Required

Regency B36XTCE Gas Fireplace

Max. 36”(0.9m)

Flex 42-1/8"(1.0m)

Rigid 44-1/4"(1.1m)

Factory Setting - No Restrictor Required

INSTALLATION

HORIZONTAL TERMINATIONS

FLEX VENT 5" X 8"

These venting systems, in combination with the B36XTCE Direct Vent Gas Fireplace, has been tested and listed as a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations Diagram in "Exterior Vent Termination Locations" section.

Regency® Direct Vent (Flex) System 4 foot Termination Kit (Part# 946-615) includes all the parts needed to install the B36XTCE with a either a top or rear vent.

Note: If top venting this unit, the 5" x 8" venting may only be used if venting to the minimum of 42-1/3" to centerline. No other application is approovred.

FPI Kit # Length Contains: #946-615 4 Feet 1) 8” ﬂ exible liner (Kit length)

2) 5” ﬂ exible liner (Kit length)

3) spring spacers

4) thimble

5) AstroCap termination cap

6) screws

7) tube of Mill Pac

8) plated screws

9) S.S. screws #8 x 1-1/2” drill point

10) vinyl siding standoff

1) 8" dia. ﬂ exible liner (4 ft. length)

2) 5" dia. ﬂ exible liner (4 ft. length)

3) spring spacers (4)

4) thimble

5) AstroCapXL termination cap (1)

6) screws (12)

7) tube of Mill Pac (1)

8) plated screws (8)

9) screws #8 x 1-1/2" Drill Point,

Stainless Steel (4)

10) vinyl siding standoff

Notes:

1) Liner sections should be continuous without any joints or seams.

2) Only Flex pipe purchased from Regency may be used for Flex installations.

3) Regency® Direct Vent System (Flex) is only approved for horizontal terminations.

Note: If longer runs are required - rigid pipe must be used.

Regency B36XTCE Gas Fireplace

Standoff (Optional)

Pipe Length

90 Elbow

Rigid Pipe Adaptor

HORIZONTAL TERMINATIONS

RIGID PIPE 5" X 8"

Vinyl Siding

Horizontal

Termination

Cap

Wall Thimble

Pipe Length

Rigid Pipe Adaptor

INSTALLATION

l S

f (

tio

Horizontal Termination

A Top Vent - No Vertical Rise

• When venting with a 90° elbow directly off the unit, must use 5" X 8" AstroCapXL™ Flex vent or approved Rigid Vent System

• Max. 3 ft. horizontal run

B Rear Vent w/ Horizontal Termination

• Can only use 5" x 8" venting

• Max. 3ft. horizontal run

Regency B36XTCE Gas Fireplace

INSTALLATION

HORIZONTAL TERMINATIONS

ASTROCAP XL & RIGID REAR VENT KIT FOR CORNER INSTALLATIONS

Designed for a minimum vent conﬁguration when using a rear vent application with a horizontal termination in a corner installation.

RIGID PIPE 5" X 8"

Kit 946-612 Includes

1 AstroCap XL 946-623/P

1 Rigid Pipe Adaptor 770-994 1 Vinyl Siding Standoff (Optional) 946-625 1 Wall Thimble 58DVA-WT 1 6" galvanized rigid pipe 58DVA-06 1 8-1/2" galvanized pipe extension 58DVA-08A 1 45º galvanized elbow 58DVA-E45 1 90 ml MillPac 948-128

Standoff

(Optional)

Wall Thimble

Astrocap

3-1/4"

75-1/4"

Placement of the unit into the corner Back top corner of unit to wall 4" Inside corner out along the wall 53" Across the face of the unit, wall to wall 75" Inside corner to front face of the unit 37-1/2"

”

45 elbow

Rigid Pipe Adaptor

Pipe Length

26-1/2” (673mm)

Regency B36XTCE Gas Fireplace

INSTALLATION

10 14 16

18 20

VENTING ARRANGEMENTS FOR HORIZONTAL TERMINATIONS

RIGID PIPE 4" X 6-5/8"

(MUST USE REDUCER PART # 946-606 & 770-994 RIGID PIPE ADAPTOR)

The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o two 45o elbows equal one 90o elbow).

Horizontal (Feet)

Restrictor 2-1/4” Open

Set 1

49"

Vertical Height (Feet)

(1245mm) Minimum Height

• Maintain clearances to combustibles as listed in "Clearances" section

• Horizontal vent must be supported every 3 feet.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

• A wall thimble is mandatory for all horizontal terminations due to high temperatures.

Requirement

No Vent Restrictor

ALL RIGID PIPE SYSTEMS

4" INNER DIAMETER

6-5/8" OUTER DIAMETER

Regency B36XTCE Gas Fireplace

INSTALLATION

Pipe Length

Vertical

Termination

Cap

Storm Collar

Flashing

Ceiling Firestop

Rigid Pipe Adaptor

Pipe

Length

Pipe Length

90 Elbow

Astrocap

(946-523/P)

Wall Thimble

Vinyl Siding

Standoff (Optional)

Reducer

(4” x 6-5/8” venting)

43”

HORIZONTAL OR VERTICAL TERMINATIONS

RIGID PIPE 4" X 6-5/8"

(MUST USE REDUCER PART # 946-606 & 770-994 RIGID PIPE ADAPTOR)

The minimum components required for a basic horizontal termination using 4" x 6-5/8" are: 1 Rigid Pipe Adaptor (770-994)

1 Reducer (946-606) 1 90o Elbow 1 Wall Thimble 1 Length of pipe to suit wall thickness 1 Horizontal Termination Cap

Wall thickness is measured from the back standoffs to the inside mounting surface of termination cap. For siding other than vinyl furring strips may be used, instead of the vinyl siding standoff, to create a level surface to mount the vent terminal. The Terminal must not be recessed into siding. Measure the wall thickness including furring strips.

If a Vinyl Siding Standoff is required (it must be used with vinyl siding), measure to outside surface of wall without siding and add 2 inches. Note: The 4" x 6-5/8" Regency Flex Kits (946-515 & 946-516) are not approved for use with this ﬁ replace. Only rigid pipe may be used

when 4" x 6-5/8" is used.

ASTROCAP # 946-523/P

DIMENSIONS

11”

(279mm)

11”

(279mm)

WARNING:

Do not combine venting components from different venting systems.

The FPI AstroCap American Metal Products, Security Secure Vent®, AmeriVent Direct Vent, ICC Excel. AstroCapTM is the proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

and FPI Riser Vent terminal are certiﬁ ed for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent,

Exception: However, use of the AstroCapTM and FPI Riser is acceptable with all systems.

This product has been evaluated by Intertek for using a Rigid Pipe Adaptor in conjunction with DuraVent Direct V ent, Selkirk Direct-T emp, Ameri Vent Direct Vent, Security Secure Vent and ICC Excel Venting Systems. Use of these systems with the Rigid Pipe Adaptor is deemed acceptable and does not affect the Intertek WHI listing of components.

Regency B36XTCE Gas Fireplace

TWO (2) 90O ELBOWS (RIGID PIPE 4" X 6 - 5/8")

One 90o elbow = Two 45o elbows.

HORIZONTAL TERMINATIONS

INSTALLATION

Option V H + H1

A) 0' Min. 2' Max. B) 1' Min. 3' Max. C) 2' Min. 4' Max. D) 3' Min. 5' Max. E) 4' Min. 6' Max. F) 5' Min. 7' Max. G) 6' Min. 8' Max

No Vent Restrictor Installed

Lengths do not include elbow indicated. Must use reducer # 946-606 and rigid pipe adaptor #770-994.

With these options, maximum total pipe length is 30 feet with minimum of 6 feet total vertical and maximum 8 feet total horizontal.

Please note minimum 1 foot between 90o elbows is required.

HORIZONTAL TERMINATIONS

THREE (3) 90O ELBOWS (RIGID PIPE 4" X 6 - 5/8")

One 90o elbow = Two 45o elbows.

Option V H V + V1 H + H1

A) 0' Min. 1' Max. 1' Min. 2' Max. B) 1' Min. 2' Max. 3' Min. 3' Max. C) 2' Min. 2' Max. 5' Min. 4' Max. D) 3' Min. 2' Max. 7' Min. 5' Max.

With these options, max. total pipe length is 30 feet with min. of 12 feet total vertical and max. 9 feet total horizontal.

E) 4' Min. 3 Max. 9' Min. 6' Max. F) 5' Min. 4' Max. 10' Min. 7' Max. G) 6' Min. 5' Max. 11' Min. 8' Max.

Please note min. 1 foot between 90 elbows is required.

H) 7' Min. 6' Max. 12' Min. 9' Max.

No Vent Restrictor Installed

Lengths do not include elbow indicated. Must use reducer # 946-606 and rigid pipe adaptor #770-994.

Regency B36XTCE Gas Fireplace

INSTALLATION

204 10

VENTING ARRANGEMENTS FOR VERTICAL TERMINATIONS

RIGID PIPE 4" X 6-5/8"

(MUST USE REDUCER PART # 946-606 & 770-994 RIGID PIPE ADAPTOR)

The shaded area in the Diagram shows all allowable combinations of straight vertical and offset to vertical terminations, using two 90o elbows, with Rigid Pipe Venting Systems for Propane and Natural Gas. Two 45

Horizontal (Feet)

Restrictor 1-1/16” Open

Set 3

elbows equal to one 90o elbow. Maximum of four 45o elbows allowed.

Maximum: 35.5 ft. (10. m)8

Vertical Height (Feet)

• Vent must be supported at offsets.

• Firestops are required at each ﬂ oor level and whenever passing through a wall.

• Maintain clearances to combustibles as listed in the "Clearances" section.

• Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting to 2-14" opening ,1-5/8"opening and to 1-1/16" opening.

Restrictor 1-5/8” Open

Set 2

No Restrictor

Maximum 10’ Centerline to Centerline

(1.2m)

Min. 49”

Maximum 8’ Centerline to Centerline

8’ (2.4m)

Minimum

Restrictor 2-1/4” Open

Set 1

Maximum: 25 ft. (7.6m)

Note: Must use optional ﬂ ue adapter when using Rigid Pipe (Part # 770-994).

Regency B36XTCE Gas Fireplace

VERTICAL TERMINATIONS

THREE (3) 90O ELBOWS (RIGID PIPE 4" X 6 - 5/8")

INSTALLATION

One 90o elbow = Two 45o elbows.

Option V H + H1 V + V1 A) 0' Min. 2' Max. 2' Min. B) 1' Min. 2' Max. 3' Min. C) 2' Min. 3' Max. 4' Min. D) 3' Min. 4' Max. 6' Min. E) 4' Min. 5' Max. 7' Min. F) 5' Min. 6' Max. 8' Min. G) 6' Min. 7' Max. 9' Min. H) 7' Min. 8' Max. 10' Min.

No Vent Restrictor Installed

Lengths do not include elbow indicated. Must use reducer # 946-606 and rigid pipe adaptor #770-994

With these options, max. total pipe length is 30 feet with min. of 10 feet total vertical and max. 8 feet total horizontal.

Please note min. 1 foot between 90o elbows is required.

Regency B36XTCE Gas Fireplace

INSTALLATION

VENTING ARRANGEMENTS

WITH CO-LINEAR FLEX SYSTEM

THE APPLIANCE MUST NOT BE

CONNECTED TO A CHIMNEY FLUE

SERVING A SEPARATE SOLID FUEL

BURNING APPLIANCE.

This appliance is designed to be attached to two 3" (76mm) co-linear aluminium ﬂ ex running the full length of the chimney. See the Venting Arrangements on next page for minimum and maximum heights.

Required Parts:

Part # Description

946-529 Co-linear DV Vertical Termination Cap 948-305 3" Flex - 35 ft. 946-563 Co-Axial to Co-Linear Adapter Kit which contains the following: Co-linear Flex Adapter Outer Pipe Inner Pipe Adapter 770-994 Rigid Pipe Adaptor 946-606 Vent Reducer

Alternate Approved Caps

Masonry chimneys may take various contours which the ﬂ exible liner will accommodate. However, keep the ﬂ exible liner as straight as possible, avoid unnecessary bending.

The Air Intake pipe must be attached to the inlet air collar of the termination cap.

Co-linear DV

Vertical Termination

Cap # 946-529

A maximum

of two certified

joiner kits

may be used

per length.

Flex Liner

#948-305 (35 ft)

Exhaust

Flue

46dva-VC Vertical Termination Cap 46dva-VCH High Wind Cap 46dva-GK

NOTE: See detailed venting arrangements,

vertical terminations, co-linear ﬂ ex system

into masonry ﬁ replaces in this manual.

3" Co-linear Adapter with ﬂ ashing

Reducer #946-606

(4 x 6-5/8 venting)

Rigid Pipe Adapter

# 770-994

Outer

Pipe with Kit# 946-563

Pipe Length

90 Degree

Elbow

Air Intake

Co-Linear

Flex

Adapter

with Kit#

946-563

Inner Pipe

Adapter with Kit# 946-563

Regency B36XTCE Gas Fireplace

INSTALLATION

VERTICAL TERMINATIONS

CO-LINEAR FLEX SYSTEM INTO MASONRY FIREPLACES

FOR BOTH RESIDENTIAL & MANUFACTURED HOMES

Regency B36XTCE Gas Fireplace

The shaded area in the Diagrams show the allowable vertical terminations.

INSTALLATION

UNIT INSTALLATION

WITH HORIZONTAL

TERMINATION

4" X 6-5/8" OR 5" X 8"

VENTING

(Rigid Vent Systems)

Minimum Vent Clearances

to Combustibles

* Clearances noted below must be maintained; except when passing through a wall, ceiling or at the termination where the use of a ﬁ restop or wall thimble reduces clearance to 1-1/2" (38mm).

Horizontal Top* 2" (51mm)* Horizontal Side 1-1/2 " (38mm) Horizontal Bottom 1-1/2" (38mm) Vertical Vent 1-1/2" (38mm)

Below are the recommended framing dimensions (inside measurements) for the 4" x 6-5/8" and 5" x 8" rigid vent terminations for use with a ﬁ restop or wall thimble.

Recommended Framed Opening

Size

Vent Size Framing Size

4" x 6 - 5/8" 10" x 10"

5" x 8" 11" x 11"

Install the vent system according to the manufacturer's instructions included with the components.

1) Set the unit in its desired location. Check to determine if wall studs or roof rafters are in the way when the venting system is attached. If this is the case, you may want to adjust the location of the unit. Rough in the gas preferably on the right side of the unit and the electrical (junction block is on the left side) on the left.

2) Direct Vent pipe and ﬁ ttings are designed with special twist-lock connections to connect the venting system to the appliance ﬂ ue outlet. A twist-lock appliance adaptor is required.

3) In conjunction with the Approved Vent system, install the adaptor after the unit is set in its desired location. Put a bead of high temperature silicone inside the outer section of the adapter and a bead of Mill Pack on the inner collar. Slip the adapter over the existing inner and outer ﬂ ue collar. Fasten to the outer collar only with the 3 supplied screws (drilling pilot holes will make this easier).

4) Level the ﬁ replace and fasten it to the framing using nails or screws through the top and side nailing strips.

Diagram 1

5) Assemble the desired combination of pipe and elbows to the appliance adaptor and twist-lock for a solid connection.

Note: For best results and optimum

performance with each approved venting system, it is highly recommended to apply “Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty. Silicone (red RTV) is optional.

Horizontal runs of vent must be supported every 3 feet (0.9meter). Wall straps are available for this purpose.

6) Mark the wall for a square hole.-see chart to

left for size. The center of the square hole should line up with the center-line of the horizontal pipe. Cut and frame the square hole in the exterior wall where the vent will be terminated. See Diagram 2 for center line requirements.

If the wall being penetrated is constructed of

non-combustible material, i.e. masonry block or concrete, an 8" (203mm) diameter hole is acceptable.

Note: a) The horizontal run of vent must be level,

or have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present the possibility of a ﬁ re.

b) The location of the horizontal vent

termination on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed. See "Exterior Vent Termination Locations" section for more details.

center

of hole

49” (1245mm)

44-1/4” (1124mm)

Rear Vent

Diagram 2

Min. height (5” x 8”)

26-1/2” (673mm)

Min. height (4” x 6-5/8”)

7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5). Install the termination cap.

Note: If installing termination on a vinyl

siding covered wall, a vinyl siding standoff or furring strips must be used to ensure that the termination is not recessed into the siding.

Diagram 5

The four wood screws provided should be re-

placed with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

8) Before connecting the horizontal run of vent pipe to the vent termination, slide the Wall Thimble over the vent pipe. The wall thimble is required for all horizontal terminations.

9) Slide the appliance and vent assembly towards the wall carefully inserting the vent pipe into the vent cap assembly. It is important that the vent pipe extends into the vent cap sufﬁ cient distance so as to result in a minimum pipe overlap of 1-1/4 inches (32mm). Secure the connection between the vent pipe and the vent cap.

10) Install wall thimble in the center of the framed hole and attach with wood screws (Diagram

7).

Diagram 7

ASTROCAP # 946-523/P

DIMENSIONS

11”

(279mm)

11”

(279mm)

Regency B36XTCE Gas Fireplace

INSTALLATION

UNIT INSTALLATION

WITH HORIZONTAL

TERMINATION

5" X 8" VENTING

(Flex Vent Systems)

Minimum Vent Clearances

to Combustibles

* Clearances noted below must be maintained; except when passing through a wall, ceiling or at the termination where the use of a ﬁ restop or wall thimble reduces clearance to 1-1/2" (38mm).

Horizontal Top 2" (51mm) Horizontal Side 1-1/2 " (38mm) Horizontal Bottom 1-1/2" (38mm) Vertical Vent 1-1/2" (38mm)

Below are the recommended framing dimensions (inside measurements) for the 4" x 6-5/8" and 5" x 8" rigid vent terminations for use with a ﬁ restop or wall thimble.

Recommended Framed Opening

Size

Vent Size Framing Size

5" x 8" 11" x 11"

NOTE: Horizontal sections must be sup-

ported at intervals not exceeding 3 feet (0.9 meter). (Flame picture and performance will be affected by sags in the liner).

4) Separate the 2 halves of the wall thimble and

securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom. Fasten the other thimble half to the inside wall. The thimble halves slip inside each other and can be adjusted for 2 x 4 or 2 x 6 walls.

5) Slip the assembled liner and termination assembly through the thimble making sure the termination cap faces up (there are markings on the cap that show which wayis up). This will position the termination cap with proper down slope for draining water. Fasten the cap to the outer wall with the 4 supplied screws.

6) Pull the centre inner and outer ﬂ ex liner out enough to slip over the ﬂ ue collars of the ﬁ replace. (You may wish to cut the liner shorter to make it more workable.) Do not bend liner more than 90

slip over the collars a minimum of 1-3/8".

7) Apply Mill Pac over the ﬁ replace inner ﬂ ue collar and slip the inner ﬂ ex liner down over it and attach with 3 supplied screws.

. The liners must

ASTROCAPXL

DIMENSIONS (946-623/P)

center

of hole

1) Locate the unit in the framing, rough in the gas (preferably on the right side of the unit). Locate the centerline of the termination and mark wall accordingly. Cut an square hole in the wall - see chart (inside dimension).

Note: If installing termination on a siding

covered wall, a vinyl siding standoff or vinyl furring strips must be used to ensure that the termination is not recessed into the siding.

2) Level the ﬁ replace and fasten it to the fram-

ing using nails or screws through the nailing strips.

3) Assemble the vent assembly by applying Mill Pac to the inner ﬂ ue collar of the termi- nation and slipping the inner ﬂ ex liner over it at least 1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill Pac or high temperature silicone to the outer ﬂ ex pipe and slip it over the outer ﬂ ue collar of the vent terminal at least 1-3/8"(35mm) and fasten with the 3 screws.

8) Do the same with the outer ﬂ ue collar and outer ﬂ ex liner.

9) Apply a bead of silicone between the thimble and termination and around the outer edge of the terminal at the wall in order to keep the water out.

IMPORTANT: Do not locate termination hood where excessive snow or ice buildup may occur. Be sure to check vent termination area after snow falls, and clear to prevent accidental blockage of venting system. When using snow blowers, make sure snow is not directed towards vent termination area.

5” dia. flue pipe with spring spacer

Screws

8" dia. air intake

Wall Thimble

Rear Vent

Min. height (Flex)

42-1/8” (1070mm)

26-1/2” (673mm)

2”x4”or2”x6”

AstroCap XL

Termination Cap

Screws

Vinyl Siding

Regency B36XTCE Gas Fireplace

INSTALLATION

UNIT INSTALLATION

WITH VERTICAL

TERMINATION

4" X 6-5/8" VENTING

(Rigid Vent Systems)

4) Assemble the desired lengths of pipe and elbows. Ensure that all pipes and elbow connections are in the fully twist-locked position and sealed.

Diagram 4

(MUST USE REDUCER

#946-606 AND RIGID PIPE ADAPTOR

#770-994)

1) Maintain the 1-1/2" clearances

(air spaces) to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafter, or other nearby combustible surfaces. Do not pack air spaces with insulation. Check "Venting" Sections for the maximum vertical rise of the venting system and the maximum horizontal offset limitations.

2) Set the gas appliance in its desired location. Drop a plumb bob down from the ceiling to the position of the appliance ﬂ ue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, and mark the spot where the vent will penetrate the roof.

3) A Firestop spacer must be installed in the ﬂ oor or ceiling of every level. To install the Firestop spacer in a ﬂ at ceiling or wall, cut a 10 inch square hole. Frame the hole as shown in Diagram 2 and install the ﬁ restop.

Note: All vertical terminations are vented using 4" x 6-5/8" venting and reducer #946-606 and rigid pipe adaptor #770-994.

Diagram 2

Diagram 1

NOTE: For best results and optimum performance with each approved venting system, it is highly recommended to apply “Mill-Pac” sealant (supplied) to every inner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty. Silicone (red RTV) is optional.

5) Cut a hole in the roof centered on the small

drilled hole placed in the roof in Step 2. The hole should be of sufﬁ cient size to meet the minimum requirements for clearance to combustibles of 1-1/2". Slip the ﬂ ashing under the shingles (shingles should overlap half the ﬂ ashing) as per Diagram 3.

Diagram 3: The upper half of the ﬂ ashing is installed under the rooﬁ ng material and not

nailed down until the chimney is installed. This

allows for small adjustments.

6) Continue to assemble pipe lengths.

Note: If an offset is necessary in the attic to

avoid obstructions, it is important to support the vent pipe every 3 feet, to avoid excessive stress on the elbows, and possible separation. Wall straps are available for this purpose.

Galvanized pipe is desirable above the rooﬂ ine

due to its higher corrosion resistance. Continue to add pipe sections through the ﬂ ashing until the height of the vent cap meets the minimum height requirements speciﬁ ed in Dia. 4 or local codes. Note that for steep roof pitches, the vertical height must be increased. A poor draft, or down drafting can result from high wind conditions near big trees or adjoining roof lines, in these cases, increasing the vent height may solve the problem.

7) Ensure vent is vertical and secure the base

Roof Pitch Minimum Vent Height Feet Meters ﬂ at to 7/12 2 0.61 over 7/12 to 8/12 2 0.61 over 8/12 to 9/12 2 0.61 over 9/12 to 10/12 2.5 0.76 over 10/12 to 11/12 3.25 0.99 over 11/12 to 12/12 4 1.22 over 12/12 to 14/12 5 1.52 over 14/12 to 16/12 6 1.83 over 16/12 to 18/12 7 2.13 over 18/12 to 20/12 7.5 2.29 over 20/12 to 21/12 8 2.44

of the ﬂ ashing to the roof with rooﬁ ng rails, slide storm collar over the pipe section and seal with a mastic.

8) Install the vertical termination cap by twistlocking it.

Note: Any closets or storage spaces, which

the vent passes through must be enclosed.

GAS LINE

INSTALLATION

The gas line is brought through the right side of the appliance. The gas valve is situated on the right hand side of the unit and the gas inlet is on the right hand side of the valve.

The gas line connection may be made of rigid pipe, copper pipe or an approved ﬂ ex connector . (If you are using rigid pipe, ensure that the valve can be removed for servicing.) Since some municipalities have additional local codes it is always best to consult with your local authorities and the CAN/CGA B149 installation code.

For USA installations follow local codes and/ or the current National Fuel Gas Code, ANSI Z223.1.

When using copper or ﬂ ex connectors use only approved ﬁ ttings. Always provide a union so that gas lines can be easily disconnected for servicing. Flare nuts for copper lines and ﬂ ex connectors are usually considered to meet this requirement.

Important: Always check for gas leaks with a soap and water solution or gas leak detector. Do not use open ﬂ ame for leak testing.

Regency B36XTCE Gas Fireplace

INSTALLATION

PILOT ADJUSTMENT

Periodically check the pilot ﬂ ames. Correct ﬂ ame pattern has three strong blue ﬂ ames: 1 ﬂ owing around the thermopile, 1 around the thermocouple and 1 ﬂ owing across the burner (it does not have to be touching the burner).

Note: If you have an incorrect ﬂ ame pattern, contact your FPI dealer for further instructions.

Incorrect ﬂ ame pattern will have small, probably yellow ﬂ ames, not coming into proper contact with the rear burner or thermopile or thermocouple.

B36XTCE -NG System Data

For 0 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: #35 Max. Input Rating 31,000 Btu/h

Min. Input Rating 21,500 Btu/h Supply Pressure min.5.0" w.c.

Manifold Pressure (High) 3.5"+/- 0.2" w.c.

Manifold Pressure (Low) 1.6"+/- 0.2" w.c.

B36XTCE - LP System Data

For 0 to 4500 feet altitude

Burner Inlet Oriﬁ ce Sizes: #51 Max. Input Rating 31,000 Btu/h

Min. Input Rating 25,000 Btu/h Supply Pressure min.11.0" w.c.

Manifold Pressure (High) 10"+/- 0.2"w.c.

Manifold Pressure (Low) 6.4"+/- 0.2"w.c.

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig. (3.45 kPa). Disconnect piping from valve at pressures over 1/2 psig.

The manifold pressure is controlled by a regulator built into the gas control, and should be checked at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should be checked using the valve pressure ports on the valve.

1) Make sure the valve is in the "OFF" position.

2) Loosen the "IN" and/or "OUT" pressure

tap(s), turning counterclockwise with a 1/8" wide ﬂ at screwdriver.

3) Attach manometer to "IN" and/or "OUT" pressure tap(s) using a 5/16" ID hose.

4) Light the pilot and turn the valve to "ON" position.

5) The pressure check should be carried out with the unit burning and the setting should be within the limits speciﬁ ed on the safety label.

6) When ﬁ nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" ﬂ at screwdriver. Note: Screw should be snug,

but do not over tighten.

HIGH ELEVATION

This unit is approved in Canada for altitude to 4500 ft. (CAN/CGA-2.17-M91). For Natural Gas installations above 4500 ft. follow current CAN/ CGA-B149.1.

1) Manual high/low adjustment

2) Pilot adjustment

3) Outlet Pressure Tap

4) Inlet Pressure Tap

5) Pilot Outlet

6) Main Gas Outlet

7) Main Gas Inlet

Regency B36XTCE Gas Fireplace

886 S.I.T. VALVE DESCRIPTION

INSTALLATION

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

CONVERSION KIT #576-972 FROM NG TO LP

for B36XTCE using SIT 886 NOVA Gas Valve

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LP Conversion Kit # 576-972

Conversion Kit Contains: Qty. Part # Description

1 904-645 Burner Oriﬁ ce #51 1 904-529 5/32" Allen Key 1 918-590 Decal "Converted to LPG" 1 908-528 Red "LP" label 1 910-037 LP Injector (Pilot

Oriﬁ ce)

1 918-961 Instruction Sheet

Installation of LP Conversion Kit:

1) Shut off the gas and electrical supply.

2) Remove the louvers (and Arch screen

doors if they are installed).

3) Open the ﬂ ush door and remove the

door.

4) Remove the logs and embers (if already

installed).

5) Loosen the 2 screws holding the Burner

Assembly to the ﬁ rebox base. Slide the Burner Assembly to the left to release it from the oriﬁ ce and lift out.

6) Remove the pilot shield by removing 2

screws.

7) Remove the wire clip below the pilot cap.

8) Pull off the pilot cap to expose the pilot

oriﬁ ce.

9) Unscrew the pilot oriﬁ ce with the allen

key; then replace with the LPG pilot oriﬁ ce, provided in the kit.

10) Re-install pilot cap and pilot shield.

11) Remove burner oriﬁ ce with a 1/2"

wrench. Use another wrench to hold on to the elbow behind the oriﬁ ce. Discard oriﬁ ce.

Remove the 2 screws, push Burner Assembly

to the left and lift out.

12) Reinstall new burner oriﬁ ce LPG

stamped #51 and tighten.

13) Reinstall burner assembly.

14) Adjust aeration accordingly.- see

manual for details.

Regency B36XTCE Gas Fireplace

15) Remove Hi/Lo pressure regulator by removing 2 screws as

shown below. Reverse steps to install LP pressure regulator.

16) Attach the label “This unit has been converted to LPG” near or

on top of the serial # decal.

17) Replace yellow “NG” label with red “LPG” label.

18) Reverse steps 3 - 1.

19) Check for gas leaks.

20) Check inlet and outlet pressures.

INSTALLATION

21) Check operation of ﬂ ame control.

Installer Notice:

These instructions must be left

with the appliance.

Regency B36XTCE Gas Fireplace

INSTALLATION

BRICK PANEL INSTALLATION

Dangerous operating conditions may occur if the panels are broken.

1) Unwrap the Brick Panels from the protective wrapping.

2) Ensure that the logs are not in the unit.

Top Panel

Back Panel

Left Panel

3) Remove the heat deﬂ ector (if installed) by removing the 2 screws securing the heat deﬂ ector from the top of the ﬁ rebox.

Handle with care. DO NOT FORCE INTO POSITION.

Right Panel

5) Remove the hex head screw on the upper left side of the ﬁ rebox wall. Position left brick panel in place and secure with the brick panel clip and screw.

Heat deﬂ ector

4) Install the back brick panel ﬁ rst - use caution when clearing the burner assembly and rear log tray so the panel is not damaged.

Note: Ensure that an equal space (gap) is maintained on both the right and left side - when installing the back panel.

Back Panel Installed

6) Slide top brick panel under left and back brick panel, use care not to damage panel.

7) Right brick panel is installed last, follow the same procedure as for left panel (see step 5).

Final Brick Panel Installation

8) Reinstall top heat deﬂ ector (reverse Step 3).

Regency B36XTCE Gas Fireplace

INSTALLATION

OPTIONAL BLACK ENAMEL PANEL INSTALLATION

Black Enamel Panels

• Black Enamel panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time. Claims for damage after installation will not receive consideration.

• Black Enamel panels will discolor a little during normal operation. This is normal and should not be considered a defect.

All hand and ﬁ nger marks MUST be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any ﬁ n-

gerprints before applying heat to the unit. Failure to do this will result in burn stains on panels which you will be unable to remove. Not protected by product warranty.

3) Install the top panel next - slide the panel in over top of the back panel

TOP

- orient the panel so the fold in the metal faces in (see inset A).

RIGHT

1) Remove the heat deﬂ ector by removing the 2 screws securing the heat deﬂ ector to the top of the ﬁ rebox (see Diagram 2).

Heat deﬂ ector

2) Install the back panel ﬁ rst - use care when clearing the burner assembly and rear log tray, so panel is not scratched.

BACK

LEFT

Diagram 1

Diagram 2

Fold

Diagram 4

4) Remove 1 screw (see inset A), position right side panel in ﬁ rebox position panel clip in place and secure with 1 screw (see inset B). Tighten the screw.

Diagram 5

5) Repeat step 4 for left side panel.

Regency B36XTCE Gas Fireplace

Diagram 3

6) Reverse step 1.

Final Installation

Diagram 6

INSTALLATION

LOG SET INSTALLATION

Installation of Optional Panels must be completed before installing the log set.

Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with pilot operation.

Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty.

Log Kit #576-930 contains the following pieces:

A Right Front Log

B Left Front Log

C Top Middle Log

D Top Right Log

E Rear Log

902-156 Lava Rocks

902-179 Vermiculite

946-669 Platinum Embers

(supplied w/packaged manual)

2) Spread vermiculite along the base of the ﬁ rebox.

Vermiculite

3) Place Log E on the rear log support pins with the ﬂ at side to the back.

1) Carefully remove the logs from the packaging and unwrap them. The logs are fragile, handle with care - do not force into position.

4) Place Log B on the front left side of the burner. Position the notch

on the bottom left side of the log into the left side of the grate.

Slide Log B back towards Log E until the ﬂ at surface on Log B rests

up against the tabs on the burner and grate - this maintains a

necessary gap between Logs B & E.

Tabs on

burner &

grate

Notch

Note: See ﬁ nal positioning of Log B on next page.

Regency B36XTCE Gas Fireplace

INSTALLATION

5) Place Log A on the front right side of the burner. Position the notch

on the bottom right side of the log into the right side of the grate.

Slide Log A back towards Log E until the ﬂ at surface on Log A rests

up against the tabs on the burner and grate - this maintains a

necessary gap between Logs A & E.

Note: Use the notch on the bottom of Log A as a guide -see below.

Tabs on

burner &

grate

6) Position Log D with the ﬂ at side toward Log E.

Fit Log D into right peg on Log E.

Right Peg - Log E

7) The notch on the bottom of Log D rests against the knot on Log A (as shown below).

Back of Log A

Regency B36XTCE Gas Fireplace

Notch location on underside

of Log A

(runs from back - front)

INSTALLATION

8) Place the lava rocks on the front of the burner tray in the places shown in the photo.

Separate platinum embers and place on the front of the burner tray in and around the lava rocks. Avoid stacking platinum embers. Platinum embers may be placed over burner ports.

Lava Rocks

9) Position Log C with the ﬂ at side toward Log E.

Fit Log C onto left peg on Log E - the notch on the bottom of Log C rests against the 3rd (from the left) grate post.

Platinum Embers

10) Test ﬁ re to ensure proper light off (make sure ﬂ ame ﬂ ows

smoothly from one end of the burner to the other). If there is any ﬂ ame hesitation, check that area for any blockage of the burner ports.

Notch in log C

Left Peg - Log E

3rd Grate Post

Regency B36XTCE Gas Fireplace

OPTIONAL FAN INSTALLATION

INSTALLATION

Important: 120 Volt AC power is needed for the fan switch and blower. The receptacle box will be installed on the left hand side of the unit and will need to be wired by a qualiﬁ ed electrician prior to fan assembly being installed. The neutral (wider) slot of the polarized receptacle should be at the top.

Unit must be grounded at all times. Do not cut the ground terminal off under any circumstances.

1) Shut the power off.

2) Open the bottom louver. Remove the

standard ﬂ ush door.

3) Attach the red and black wires

to fan motor as shown in diagram 1.

Black wire

Diagram 1

4) Turn the fan base on its side (with the base facing towards you) and then slide the fan in towards the rear of the unit. Turn the fan upright and slip it over the two mounting studs. Take care not to damage the insulation on the fan base. Ensure that the fan blades do not rub against the valve tubing.

Red wire

6) Slide the thermodisc/cover assembly into

the bracket clip on the underside of the ﬁ rebox. Check that no wire will touch the hot surfaces. Diagram 3 and 4.

7) Plug the fan power cord into the rear end of

the receptacle box to provide the maximum clearance from the louvers.

*Ensure that there is no interference with

the wires when the louver is closed and that no wire will touch the hot metal surfaces or sharp edges.

Diagram 3

9) Secure the fan wires and power cord by attaching one of the adhesive backed wire

holder clips (Part #910-199) onto the unit base. Use the second clip to bundle up the wires approximately 4" from the control box.

Diagram 6

TO REMOVE THE FAN

1) Shut the power off.

2) Reverse the above instructions.

Note: The bearings are lubricated for life.

Do not lubricate them. Make sure you vacuum the fan area on a regular basis.

IMPORTANT: These fans collect a lot of dust from within your home. Ensure you maintain these fan motors on a regular basis by vacuuming out the fan blades and housing using a soft brush nozzle.

Diagram 2

5) Connect fan ground cable to ground lug. Refer to wiring diagram.

Electrical

Receptacle

Push Fan down

on mounting pins

Ground Lug

Plug fan power cord

Regency B36XTCE Gas Fireplace

Diagram 4

8) Slide the the Fan control box under the clip on the ﬂ oor of the ﬁ rebox. (See Diagram 5)

Diagram 5

Clip

INSTALLATION

AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEMS)

An optional AC power adaptor may be installed as a constant power source for the SureFire system.

This will avoid battery leakage and power drainage. 4-AA Battery pack may be re-installed into receiver during power outages.

NOTE: For all Gas Fireplaces 120 volt power must be brought to the receptacle box inside the ERWWRPRIWKH¿UHER[(provided with the unit).

All Freestanding Gas Stoves & Gas Inserts will need a receptacle box located outside / near the unit

NOTE: AC power adaptor is not required when using GTMF Remote

IMPORTANT: Recommend removing the 4-AA batteries in the SureFire receiver.

so that the AC Power Adaptor can be plugged in.

INSTALL AC ADAPTOR WITH SUREFIRE WALL SWITCH ONLY - (WITHOUT REMOTE)

1) Locate “DC Supply” tag on wire harness. For location in unit

see remote installation page in owners manual.

2) Connect the male end from AC adaptor to the female end tagged “DC Supply” on wiring harness in unit.

Plug AC adaptor into 120V wall outlet (or into 120V receptacle if

LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[

4) Neatly tuck any loose AC Power Adaptor wires neatly underneath / inside the appliance.

Note: (QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[

(keep wires away from the heat as much as possible).

INSTALL AC ADAPTOR WITH SUREFIRE PROFLAME GT / GTM REMOTE

This method also applies for models, HZ30E - HZ40E - L390E - HZI390E

1) Connect the male end of the AC adaptor to the female end of the

wire adaptor (supplied with AC adaptor) together as shown

Wire adaptor

Locate FCM - COM connector on the Remote wire harness -

see manual for location in unit.

AC adaptor

Plug in wire adaptor to FCM - COM connector - be careful not

WRGDPDJHHQGV7KLVRQO\¿WVRQHZD\'R1RW)RUFHLQZURQJZD\

wire adaptor

4) Plug AC adaptor into 120V wall outlet (or into 120V receptacle if

LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[

5) Neatly tuck any loose AC Power Adaptor wires neatly underneath / inside the appliance.

Note: (QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[

(keep wires away from the heat as much as possible).

FCM - COMAC adaptor

919-063

FCM - COM

Regency B36XTCE Gas Fireplace

03/04/2013

GT REMOTE INSTALLATION

INSTALLATION

1) Shut off the gas supply and disconnect all power to the unit.

2) Remove the louvers, bay door or faceplate if installed.

3) Disconnect battery pack - located on the ﬂ oor of the unit, as shown

below and discard.

4) Remove DFC (digital ﬁ rebox control box) from the ﬂ oor of the unit.

8) Plug in receiver DC supply wire - as shown below.

9) Install 4 - AA batteries into the receiver, ensure correct polarity.

10) Plug receiver wires into the back of the receiver and bundle wires

with the wire clip as shown below.

5) Disconnect wire harness, ground wire and spark wire from DFC.

See attached wiring diagram for details.

6) Identify wires in the GT remote wiring harness. (see wiring diagram.)

7) Connect the TPTH and TH wires - green to green and white to white as shown below. See attached wiring diagram for details.

TPTH

(white)

(green)

Wire Clip

11) Install the heat shield to the receiver with two screws and attach to

the ﬂ oor of the unit with a velcro pad.

Heat Shield

12) Reverse steps 5 and 4.

13) Match the remote control to the receiver - see remote control

instructions.

Regency B36XTCE Gas Fireplace

14) Reverse steps 2 and 1.

15) Check to ensure there are no gas leaks.

INSTALLATION

Optional

WALL THERMOSTAT

A wall thermostat may be installed if desired, connect the wires as per the wiring Diagram. Use table below to determine the maximum wire length.

Note: Preferable if the thermostat is

installed on an interior wall.

Regency® offers an optional programmable thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or UL approved may be used.

CAUTION

Do not wire millivolt

wall thermostat wires

to 120V wire.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

Thermostat (CP-2 System)

Wire Size Max. Length

14 GA. 50 Ft.

16 GA. 32 Ft.

18 GA. 20 Ft.

20 GA. 12 Ft.

22 GA. 9 Ft.

Optional

REMOTE CONTROL

Use the Regency® Remote Control Kit approved for this unit. Use of other systems may void your warranty.

The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate.

1) Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the ﬁ replace to that location. Use Thermostat Wire Table.

2) Connect the two wires to the gas valve.

CAUTION

Do not wire millivolt

remote control wires

to 120V wire.

3) Install 3 AAA alkaline batteries in transmitter

and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation.

Optional

WALL SWITCH

1) Run the supplied 10' of wire through the

right or left side gas inlet opening. Be careful not to damage wire.

Note: We recommend a maximum of 10'

of wire but if you wish to go with a longer run, use the Thermostat Wire Table.

2) Connect the wire to a wall switch and install

into the receptacle box. Also attach wires to the valve.

CAUTION

Do not wire millivolt

wall switch wire

to 120V wire.

Regency B36XTCE Gas Fireplace

GTM REMOTE INSTALLATION

INSTALLATION

1) Shut off the gas supply and disconnect all power to the unit.

2) Remove the louvers, bay door or faceplate if installed.

3) Disconnect battery pack - located on the ﬂ oor of the unit, as shown

below and discard.

4) Remove DFC (digital ﬁ rebox control box) from the ﬂ oor of the unit.

6) Identify wires in the GTM/GTMF remote wiring harness.

(see wiring diagram.)

7) Connect the TPTH and TH wires - green to green and white to white as shown below.

TPTH

8) Plug in receiver DC supply wire - as shown below.

5) Disconnect wire harness, ground wire and spark wire from DFC.

DFC

9) Remove the hi/lo knob if installed by removing 2 screws as shown below.

Regency B36XTCE Gas Fireplace

INSTALLATION

10) Install the stepper motor in the same location the hi/lo knob was removed from - with 2 screws as shown below.

11) Remove the receiver if installed - unplug the motor wire from the

back of the receiver - as shown below.

15) Install 4-AA batteries into the receiver.

16) Bundle all wires together and clip with supplied wire clip - as

shown below.

17) Install the heat shield to the receiver with two screws and attach

to the ﬂ oor of the unit with a velcro pad - also peel off paper on back side of wire clip and place wires conveniently in appliance.

12) Reattach wires from step 5.

13) Plug the stepper motor into the ‘motor wire as shown below.

Motor wire

14) To unattach these wires - un-clip from the wires on the stepper

motor side as shown below.

Press down this tab

Heat shield

18) Match the remote control to the receiver - see remote control instructions.

19) Reverse steps 2 and 1.

20) Check to ensure there are no gas leaks.

Regency B36XTCE Gas Fireplace

GTMF REMOTE INSTALLATION

INSTALLATION

1) Shut off the gas supply and disconnect all power to the unit.

2) Remove the louvers, bay door or faceplate, if installed.

3) Disconnect battery pack - located on the ﬂ oor of the unit, as shown

below and discard.

4) Identify wires in the GTM/GTMF remote wiring harness. (see wiring diagram.)

5) Remove DFC (digital ﬁ rebox control box) from the ﬂ oor of the unit.

7) Connect the TPTH and TH wires - green to green and white to

white as shown below.

TPTH

8) Plug in receiver DC supply wire - as shown below.

6) Disconnect wire harness, ground wire and spark wire from DFC.

DFC

9) Remove the hi/lo knob by removing 2 screws as shown below.

10) Install the stepper motor in the same location the hi/lo knob was

removed from - with 2 screws as shown below.

Regency B36XTCE Gas Fireplace

INSTALLATION

11) Install 4 - AA batteries into the receiver.

12) Plug ‘motor’ wires into the back of the receiver and bundle wires

with the wire clip - as shown below.

14) Reinstall the DFC box onto the velcro pad on the ﬂ oor of the unit.

15) Install the heat shield to the receiver with two screws and attach

to the ﬂ oor of the unit with a velcro pad.

Heat shield

16) From the wire harness, plug the FCM wire into the fan control

module.

FCM wire

13) Reattach wires from step 5.

Fan Control Module

17) Install the heat shield onto the fan control module - then install onto the velcro pad located on the ﬂ oor of the unit located left of the receiver.

18) Plug fan control module into recepticle located on the left hand

side of the unit.

19) Match the remote control to the receiver - see remote control instructions.

20) Reverse steps 2 and 1.

21) Check to ensure there are no gas leaks..

Regency B36XTCE Gas Fireplace

584 Proflame GT Series

Feature Sheet

111

INSTALLATION

(X) Indicates Included Feature

Note 1 ~ Proﬂ ame Flame Modulator for GTM & GTMF Remote Controls are sold seperately. Choice of NG or LP ﬂ ame modulator (to match unit fuel type). See Regency Retail Price pages for complete details

Note: Regency Proﬂ ame systems include a white and black wall cover & switch.

Regency B36XTCE Gas Fireplace

INSTALLATION

AERA TION ADJUSTMENT

Air shutter rod - located to the left

of the valve assembly.

The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue ﬂ ame or close for a more yellow ﬂ ame.

Minimum Air Shutter Opening:

NG 1/4" LP 3/8"

CAUTION: Carbon will be produced if air shutter

is tightly closed.

Note: Any damage due to carboning

resulting from improperly setting the aeration controls is NOT covered under warranty.

WIRING DIAGRAM

Caution: Ensure that the wires do not touch any hot surfaces and are away from sharp edges.

This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.

(Do not cut the ground terminal off under any circumstances.)

NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit) in case

the fan is installed at a later date.

PROFLAME SYSTEM WIRING DIAGRAM

CONFIGURATION: 886 ON/OFF STAND ALONE

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

SureFire™ Switch

0.886.001

Proflame Valve

Standard Main On/Off Switch or Optional Wall Switch

Note: 4 AA batteries must be installed to operate the burner switch. Do not use a 9 volt battery.

IMPORTANT: If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the

receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve.

Regency B36XTCE Gas Fireplace

Proflame System Configuration 886 GTMF Wire Diagram

PROFLAME SYSTEM WIRING DIAGRAM

GT, GTM, GTMF

Option

PROFLAME REMOTE SERIES

946-690 GT Remote System 946-691* GTM Remote System 946-692* GTMF Remote

INSTALLATION

CONFIGURATION: 886 GTMF

GTM Option

GTMF Option

SureFire™ Switch

* Must also order a 946-693-NG or 946-694 modulator if using the noted remote controls.

Regency B36XTCE Gas Fireplace

INSTALLATION

OPTIONAL ACCENT LIGHT INSTALLATION

B36XT/B36XTE Accent Light Kit # 576-959

1 Light Assembly -includes cable tie/ gasket.

1 910-997 Halogen Bulb

1 940-363 Amber glass

1 910-199 Adhesive wire clip

1 918-821 Instruction Sheet

Important: 120 Volt AC power is required to operate the light. The receptacle box will be installed on the left hand side of the unit and will need to be wired by a qualiﬁ ed electrician prior to the light installation. The neutral (wider) slot of the polarized receptacle should be at the top. A wall mounted switch should also be installed to turn the accent light on and off.

Note: Receptacle Box is switch operated. Refer to wiring diagram in the manual.

1) Shut off electrical supply.

2) Remove the louvers / full screen doors - if installed.

3) Remove the glass door.

4) Remove the logs - if installed.

5) Remove the rear log tray by removing 2 screws (locations shown

below) then lifting out.

8) When light assembly has been fully seated secure in place with 2 screws that were removed from the cover plate

9) From underneath the ﬁ rebox - slide back the protective sheath on the plug wiring to reveal connectors.

Connectors

10) Plug the red light assembly wiring into the blue plug wiring - as shown below.

NOTE: The ground wire will need to be pulled back out of the protective

casing to be able to reach the ground lug. Gently pull the end of the green wire backwards exposing enough wire to reach ground lug.

Protective Sheath

Rear Log Tray

6) Remove the 2 screws securing the cover plate to the ﬁ rebox base. Discard cover plate - keep the 2 screws.

Cover plate

7) From inside the ﬁ rebox - feed the wires from the bottom of the light assembly

- through the opening exposed after the removal of the cover plate.

Light assembly

wiring

11) Slide protective sheath back over connectors until it meets the underside of the ﬁ rebox base - to protect wires. Secure end of sheath with a cable tie.

Cable Tie

Regency B36XTCE Gas Fireplace

INSTALLATION

2) After the wiring has been connected, secure green ground wire to ground lug as shown below.

Ground lug is located on the lower left corner inside the bottom of the unit.

Ground

Lug

15) Install the halogen bulb supplied with the kit.

Important: Use caution - do not touch the bulb during

installation. Use the plastic packaging as a protective covering while installing the bulb.

16) Install a gasket over top of the bulb.

Gasket

17) Install the light diffuser by securing it to the rear log tray with 2 screws - see below.

3) Using the adhesive wire holder, neatly secure the loose wiring to the base of the unit.

Ensure wiring does not come into contact with the fan blades or any sharp metal edges.

Wire Clip

4) Reinstall the rear log tray - secure with 2 screws.

Installed diffuser shown below with 2 options:

a) With amber glass plate - for use with units without panels or with brick panels. Left and right side tabs to be bent down 90

degrees as shown below (Image A).

b) Amber glass plate covered - for use with units using stainless steel / black enamel panels as show below in Image B.

Regency B36XTCE Gas Fireplace

INSTALLATION

18) Reinstall the logs.

19) Reinstall glass door and bottom louver / full screen doors.

20) Plug the light assembly into the receptacle located on the

bottom left side of the unit.

Ground Wire Receptacle

21) Turn on electrical supply - test lights.

BULB REPLACEMENT

1) Follow steps 1- 4 from previous page.

2) Remove 2 screws to remove light diffuser plus gasket.

3) Replace the bulb - do not touch bulb with bare hands, use gloves or bulb

packaging to protect bulb.

Ground

Star washer

4) Reinstall the gasket and light diffuser.

5) Reverse steps 4-1.

LINE VOLTAGE WIRING TO RECEPTACLE IN UNIT

TO MAKE OUTLETS INDEPENDENT OF EACH OTHER

Lockwasher

Fan

ground wire

#8 Ground Lug

(mobile home

Nut

Light

Switch

approved)

Black

Fan

Switch

Red

Break Tab

Copper terminals

Black

120V AC 60 Hz

Receptacle

in Unit

Ground

Neutral

Live

Ground

ON OFF

Rotary Speed

Control

ELECTRICAL WORK MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN

Ground

Do Not Break Tab

on Neutral (silver terminals)

Optional Fan

Green

Black Red Red

To Fan (see above)

Fan

Minimum Convection

Air Temp. Switch

Optional Accent Light

Green

Regency B36XTCE Gas Fireplace

MESH GUARD INSTALLATION

1) Hook mesh guard frame over top of ﬂ ush glass door frame as shown in Diagram 1.

Push bottom part of mesh frame over ﬂ ush glass door frame until tabs snaps into place.

INSTALLATION

2) Install mesh guard and ﬂ ush glass together - following ﬂ ush glass door installation instructions.

Regency B36XTCE Gas Fireplace

INSTALLATION

FLUSH GLASS DOOR INSTALLATION

1) Line up slots on ﬂ ush glass door with tabs in ﬁ rebox. Hook slots on to tabs and lower door slowly (See Diagram 1).

Tabs in Firebox

Diagram 1

2) Lower the ﬂ ush door, then hook the 2 adjustable tension latches - close the latches to secure the ﬂ ush door (See Diagram 2).

Adjustable Tension

Latch location

Note: To remove Flush Glass door reverse Steps 1 and 2.

Diagram 2

Regency B36XTCE Gas Fireplace

OPERATING INSTRUCTIONS

INSTALLATION

OPERATING

INSTRUCTIONS

1) Read and understand these instructions

before operating this appliance.

2) Check to see that all wiring is correct and enclosed to prevent possible shock.

3) Check to ensure there are no gas leaks.

4) Make sure the glass in the glass door frame

is properly positioned. Never operate the appliance with the glass removed.

5) Verify that the venting and cap are unobstructed.

6) The unit should never be turned off, and on again without a minimum of a 60 second wait.

FIRST FIRE

The FIRST FIRE in your heater is part of the paint curing process. To ensure the paint is properly cured, it is recommended you burn your ﬁ replace for at least four (4) hours the ﬁ rst time.

When ﬁ rst operated, the unit will release an odour caused by the curing of the paint and the burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off at this time. Open a few windows to ventilate the room for a couple of hours. The glass may require cleaning.

NOTE: When the glass is cold and the appliance

is lit, it may cause condensation and fog the glass. This condensation is normal and will disappear in a few minutes as the glass heats up.

DO NOT ATTEMPT TO CLEAN THE GLASS WHILE IT IS STILL HOT!

LIGHTING

PROCEDURE

IMPORTANT To ignite or reignite the pilot, you must ﬁ rst remove the glass door.

1) Press and release on ON/OFF button once

on the remote control or ON/OFF switch.

2) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

3) The unit will turn on.

Note: The ﬁ rst try for ignition will last approxi-

mately 60 seconds. If there is no ﬂ ame ignition (rectiﬁ cation) the board will stop sparking for approximately 35 seconds. After wait time , the board will start second try for ignition by sparking for approximately 60 seconds . If there is still no positive ignition the board will go into lock out.

The system will need to be reset as follows:

a) Turn the system off using ON/OFF switch

or press ON/OFF button - if using optional remote.

b) After approximately 2 seconds turn on ON/

OFF switch or press ON/OFF button if using optional remote.

c) Repeat step 2.

SHUTDOWN

PROCEDURE

1) Turn the wall mounted switch or remote to

the "OFF" position.

NORMAL OPERATING

SOUNDS OF

GAS APPLIANCES

It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. Listed below are some examples. All are normal operating sounds and should not be considered as defects in your appliance.

Burner Tray:

The burner tray is positioned directly under the burner and is made of a different gauge material from the rest of the ﬁ rebox and body. Therefore, the varying thicknesses of steel will expand and contract at slightly different rates which can cause "ticking" and "cracking" sounds. Y ou should also be aware that as there are temperature changes within the unit these sounds will likely re-occur. Again, this is normal for steel ﬁ reboxes.

Pilot Flame:

While the pilot ﬂ ame is on it can make a very slight "whisper" sound.

Gas Control Valve: As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.

Unit Body/Firebox: Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.

Blower Thermodisc:

When this thermally activated switch turns ON it will create a small "clicking" sound. This is the switch contacts closing and is normal.

DO NOT BURN THE UNIT WITHOUT THE GLASS DOOR IN PLACE.

During the ﬁ rst few ﬁ res, a white ﬁ lm may develop on the glass front as part of the curing process. The glass should be cleaned after the unit has cooled down or the ﬁ lm will bake on and become very difﬁ cult to remove. Use a non-abrasive cleaner and DO NOT A TTEMPT TO CLEAN THE GLASS WHILE IT IS HOT.

Regency B36XTCE Gas Fireplace

2) Press "OFF" on the remote control.

6363

OPERATING INSTRUCTIONS

COPY OF LIGHTING PLATE INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

This appliance must be installed in accordance with local codes, if any;

if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier. AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou la mort. Une installation, d'ajustement, de modiﬁ cation, de service ou d'entretien peut provoquer des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémentaires consulter un installateur qualiﬁ é, une agence de service ou fournisseur de gaz.

A) This appliance is equipped with an ignition device which automatically lights the pilot.

Do not try to light the pilot by hand.

B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the ﬂ oor because some gas is heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electric switch, do not use any phone in your building.

- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the ﬁ re department.

C) Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and replace any part of the control system and any gas control which has been underwater.

A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse. Ne tentez pas d’allumer la veilleuse manuellement.

B) AVANT DE FAIRE FONCTIONNER, reniﬂ ez tout autour de l’appareil pour déceler une odeur de gaz. Reniﬂ ez près du plancher, car certains gaz sont pluslourds que l’air et peuvent s’accumuler au niveau du sol. QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil

• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le bâtiment.

• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies

C) N’utilisez pas cet appareil s’il a été plongé dansl’eau, même partiellement. Faites inspecter l’appareil par un tech-

nicien qualiﬁ é et remplacez toute partie du système de contrôle et toute commande qui ont été plongés dans l’eau.

CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface temperatures keep children, clothing and furniture, gasoline and other liquids having ﬂ ammable vapors away. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

1) Turn on ON/OFF switch

2) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.

3) The unit will turn on.

Note: The ﬁ rst attempt to ignition will last approximately 60 seconds. If there is no ﬂ ame ignition (rectiﬁ cation) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the second attempt the board will go into lock out. The system will need to be reset as follows (after going into lock out mode): a) Wait 5 minutes - turn the system off using ON/OFF switch. b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF button if using optional

c) Unit will repeat step 2.

1) Appuyez le bouton ON / OFF

2) Attendre 4 secondes. Le système d’allumage produira des étincelles pendant 60 secondes aﬁ n d’amorcer

3) Les ﬂ ammes s’allumeront. Remarque : Au premier allumage, le système tente d’allumer les ﬂ ammes pendant 60 secondes. Si l’essai est infructueux, le système fait une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectiﬁ cation. Ce délai écoulé, le système tente à nouveau d'allumer les ﬂ ammes en produisant des étincelles pendant 60 secondes. Si les ﬂ ammes ne s’allument toujours pas, le système se met en mode verrouillage. Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) : a) Attendre 5 minutes et éteindre l’appareil en réglant l’interrupteur à la position « OFF »; b) Attendre 2 secondes et rallumer le système à l’aide de l’interrupteur ou de la télécommande. c) L'unité répétera l'étape 2.

1) Turn off ON/OFF switch

2) If service is to be performed - you must disconnect power to the unit, from the battery pack, refer to

Appuyez sur le bouton ON / OFF

2) Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction

remote.

le brûleur principal.

manual.

pour plus de détails.

Natural Gas and Propane Installation Codes, CSA B149.1.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS APPLIANCE

DO NOT REMOVE THIS INSTRUCTION PLATE

918-628b

Regency B36XTCE Gas Fireplace

MAINTENANCE

INSTRUCTIONS

1) Always turn off the gas valve before cleaning.

For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged.

2) Clean appliance and door with a damp cloth (never when unit is hot). Never use an abrasive cleaner. The glass should be cleaned with a gas ﬁ replace glass cleaner. The glass should

be cleaned when it starts looking cloudy.

3) The heater is ﬁ nished in a heat resistant paint and should only be reﬁ nished with heat resistant paint. Regency® uses StoveBright Paint - Metallic Black #6309.

4) Make a periodic check of burner for proper position and condition. Visually check the ﬂ ame of the burner periodically, making sure the ﬂ ames are steady; not lifting or ﬂ oating. If there is a problem, call a qualiﬁ ed service person.

5) The appliance and venting system must be inspected before use, and at least annually, by a qualiﬁ ed ﬁ eld service person, to ensure that the ﬂ ow of combustion and ventilation air is not obstructed.

Note: Never operate the appliance without the

glass properly secured in place.

6) Do not use this appliance if any part has been

under water. Immediately call a qualiﬁ ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

liner, and subsequently dripping out the joints, Continuous condensation can cause corrosion of caps, pipe, and ﬁ ttings. It may be caused by having excessive lateral runs, too many elbows, and exterior portions of the system being exposed to cold weather.

4) Inspect joints, to verify that no pipe sections or ﬁ ttings have been disturbed, and consequently loosened. Also check mechanical supports such as Wall Straps, or plumbers' tape for rigidity.

LOG REPLACEMENT

The unit should never be used with broken logs. Turn off the gas valve and allow the unit to cool before opening door and carefully remove the logs. (The pilot light generates enough heat to burn someone.) If for any reason a log should need replacement, you must use the proper replacement log. The position of these logs must be as shown in the Diagrams under Log Installation.

Note: Improper positioning of logs may create

carbon build-up and will severely alter the unit's performance which is not covered under warranty.

GLASS GASKET

If the glass gasket requires replacement use a tadpole glass gasket (Part # 936-155).

DOOR GLASS

Your Regency® ﬁ replace is supplied with high temperature 5mm-Ceramic glass. If your glass requires cleaning, we recommend using an approved glass cleaner available at all authorized dealers. Do not use abrasive materials.

CAUTION & WARNINGS:

* Do not clean when the glass is hot. * The use of substitute glass will void all product warranties. * Care must be taken to avoid breakage of the glass. * Do not strike or abuse the glass. * Do not operate this ﬁ replace without the glass front or with a cracked or broken glass front. * Wear gloves when removing damaged or broken glass. * Replacement of the glass panels should be done by a licensed or qualiﬁ ed service per son.

GLASS REPLACEMENT

In the event that you break your glass by impact, purchase your replacement from an authorized Regency dealer only. Replacement glass (Part #940-357/P) is shipped already installed into the door frame. Reinstall as per Glass Door Installation in the "Glass Door Removal" section.

BULB REPLACEMENT

1) Follow steps 1- 4 on page 53.

2) Remove 2 screws to remove light diffuser

plus gasket.

7) In the event this appliance has been serviced check that the vent-air system has been properly resealed & reinstalled in accordance with the manufacturer's instructions.

8) Verify operation after servicing.

General Vent Maintenance

Conduct an inspection of the venting system semi-annually. Recommended areas to inspect as follows:

1) Check the Venting System for corrosion in areas that are exposed to the elements. These will appear as rust spots or streaks, and in extreme cases, holes. These components should be replaced immediately.

2) Remove the Cap, and shine a ﬂ ashlight down the Vent. Remove any bird nests, or other foreign material.

3) Check for evidences of excessive condensation, such as water droplets forming in the inner

Regency B36XTCE Gas Fireplace

3) Replace the bulb - do not touch bulb with bare hands, use gloves or bulb packaging to protect bulb.

4) Reverse steps.

MAINTENANCE

REMOVING VALVE

1) Shut off the gas and electrical supply.

2) Remove the louvers

3) Open the ﬂ ush door and remove the door.

4) Remove the logs.

5) Remove the burner/grate assembly by

removing the 2 Phillips head screws.

Diagram 1: Remove the left and right screws.

6) Slide the burner assembly to the left to release it from the oriﬁ ce, then lift it out.

8) Disconnect the inlet gas line. (see Diagram 4)

Diagram 4

9) Disconnect the wall switch wires from the valve. (see Diagram 5)

Diagram 5

10) Remove the 8 Phillips head screws securing

the valve tray assembly in place (Diagram

6) and then lift the entire assembly out (Diagram 7).

Diagram 8

INSTALLING VALVE

1) Place new valve tray into position

2) Reinstall the 8 hold down screws.

3) Hook up the 2 TP and 2 TH wires to the ap-

propriate connections on the valve.

4) Reinstall the rear log tray.

5) Install burner/grate assembly

6) Hook up the gas line and check for gas leaks

with a soap and water solution or a gas leak detector. (Do not use open ﬂ ame for leak testing.)

7) Fire up the unit temporarily

Oriﬁ ce

Diagram 2: Slide burner assembly to the left

and then remove.

7) Remove the 2 screws securing the rear log tray and lift out. Diagram 3

Diagram 3

8) Check the manifold pressure.

9) Reinstall the logs and brick panels as

needed.

10) Reinstall the door and replace the louvers.

11) Fire up the unit again and check for proper

ﬂ ame appearance and glow on logs.

Diagram 6

Diagram 7

Regency B36XTCE Gas Fireplace

MAIN ASSEMBLY

PARTS LIST

Part # Description

1) 576-084F Top Insulation Plate

2) 576-099 Top Insulation

3) 556-524 Flue Collar Outer Assembly

4) 556-095 Flue Collar Gasket

5) 556-097 Exhaust Gasket

6) 556-513 Flue Collar Inner Assembly

7) 556-088F Top Relief Plate

8) 556-094 Relief Gasket - Door Top

9) 576-901 Brick Panel - Standard Brown 576-902 Brick Panel - Standard Red 576-904 Brick Panel - Castle Stone 576-908 Black Enamel Panels

10) 820-389 Thermodisc Bracket

12) 948-165 Adjustable Tension Latch

13) 904-731 Capscrew 1/4 - 20 x 3.5 NC Gr5

14) 940-357/P Ceramic Glass

15) 556-012 Door Frame

16) * Outerbox Assembly

17) * Firebox Assembly

Part # Description

18) 576-917 Fan Assembly

19) 910-215/P Fan Motor (120 Volts) 432-966 Fan Switch Assy (120 Volts)

20) 910-813 Power Cord (120 Volts)

21) 910-330 Fan Speed Control

22) 904-586 Knob - Speed Control

23) 910-142 Thermodisc - Fan Auto ON/OFF

24) 946-000 Round Duct Adaptor

25) 910-367 Box - Plastic Switch Receptacle

26) 910-412 Fan Speed Controller

27) 910-417 Knob - White

28) 910-366 Switch Cover Plate - White

29) 946-006 Grill Plate - White

30) 946-005 Wall Adaptor Plate - White

31) 946-002 Round to Oval Adaptor

32) 946-001 Oval Duct Adaptor

33) 946-007 Angle Bracket

34) 946-517/P Fan Assembly - Heat Wave

35) 946-004 Junction Box

36) 577-929 Mesh Guard

37) 919-154 Manual * Not available as a replacement part.

Regency B36XTCE Gas Fireplace

PARTS LIST

FAN SWITCH ASSEMBLY

MAIN ASSEMBLY

Regency B36XTCE Gas Fireplace

BURNER ASSEMBLY

PARTS LIST

Part # Description

1) 576-077 Rear Log Tray

3) 576-525 B36XTCE Burner Assembly

4) 576-057 B36XTCE Grate Assembly

5) 904-644 Oriﬁ ce # 35 NG 904-645 Oriﬁ ce # 51 LP

6) 910-568 Valve NG/LP SIT High/Low 886

7) * Valve Tray - B36XTCE

Part # Description

9) 576-574E/P Valve Assembly - NG 576-576E/P Valve Assembly - LP

10) 911-006 Pilot Assembly - NG 911-007 Pilot Assembly - LP 911-004 Valve NG 911-005 Valve LP 911-012 Ignition Board (DBC) 911-013 Wiring Harness -Switch 911-018 Battery Holder 911-037 Flame Sensor 911-038 Flame Electrode 911-039 Pilot Hood 910-432 Pilot Tube

Regency B36XTCE Gas Fireplace

NOTES

Regency B36XTCE Gas Fireplace

WARRANTY

Regency® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a Regency® Product. This warranty is not transferable.

The Warranty: Limited Lifetime

The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime Warranty for ﬁ ve (5) years for parts and subsidized labour* and parts only thereafter.

Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for ﬁ ve (5) years and parts only thereafter from date of purchase. External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date of

purchase and parts only thereafter. Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating and

cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks, ie. ﬁ nger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.

Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components, and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.

FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase. Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty. Repair/replacement parts purchased by the consumer from FPI after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item

shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.

Conditions:

Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.

Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of installation. Reported damage after this time will be subject to rejection.

It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect.

The authorized selling dealer is responsible for all in-ﬁ eld service work carried out on your Regency unauthorized service persons or dealers.

At all times FPI reserves the right to inspect product in the ﬁ eld which is claimed to be defective. All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase

date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.

Exclusions:

This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim. At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.

ie. as products evolve, ﬁ eld modiﬁ cations or upgrades will not be performed. FPI will not be liable for travel costs for service work. Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy. Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy. Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy. The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence

or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical systems such as furnaces, fans, clothes dryer, etc.

Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer. FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance. Performance problems due to operator error will not be covered by this warranty policy. Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from FPI, may nullify your warranty on

this product. Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.

* Subsidy according to job scale as predetermined by FPI.

product. FPI will not be liable for results or costs of workmanship from

Regency B36XTCE Gas Fireplace

TUFSƔZ

SƔ

8BSSBOUZƔBOEƔCFƔBVUPNBUJDB

MMZƔFOUFSFEƔUP

www.regency-ﬁ re.com

Reasons to register your product online today!

• View and modify a list of all your registered products.

• Request automatic email notiﬁ cation of new product updates.

• Stay informed about the current promotions, events, and special offers on related products.

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________

7).Ɠ!Ɠ&)2%4!",%

2EGISTERƓONLINEƓATƓ

IUUQSFHFODZGJSFDPNƔ $VTUPNFS$BSFBTQY

4FFƔXFCTJUFƔGPSƔTXFFQTUBLFTƔSVMFT

Bellavista B36XTCE

Printed in Canada

Regency B36XTCE User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual