Reese 61301 User Manual

Installation Instructions





Qty. (4)

Roll Pin



Qty. (4)

Roll Pin

2

Spacer Kit for Sidewinder Turret

DEALER/INSTALLER:

(1) Provide this Manual to end user

END USER:

(1) Read and follow this Manual for Sidewinder Turret Installation.

(2) Save this Manual for Future Reference.

(3) For Sidewinder Arm Installations, Refer to there Installation Manuals.

TM

Part Number:

61301

Turret Shown w/Spacer Kit Installed

(4) Pass on copies of Manual to any other users or owner.

Note: These Instructions Are Only For Installation Of Turret Into Wing Sets.

You Should Refer To The Installation Instructions For Your Sidewinder Arm.

Equipment Required:

Fastener Kit: 61301F

Drill Bits: Not Required

Torque Wrench

Hammer

Qty. (1) Turret 61300 (Formally ST100 & ST200)



Qty. (2) Spacer Plate



INDEX

1. ASSEMBLING SPACERS ON TURRET P. 1

2. GUIDELINES FOR MATCHING WING SET P. 2

3. 5 YEAR LIMITED WARRANTY P. 3

Do Not Exceed Lower of Towing Vehicle Manufacturer’s Rating,

Trailer Manufacturer’s Rating or

Max Gross

Trailer WT (LB)

19,500 LB 3,900 LB

Max Pin

WT (LB)

2

Figure 1

1

Figure 2

Failure to follow all of these instructions may result in death or serious injury!

 2009 Cequent Performance Products

Assembling Spacers

A

AA

WARNING:

Sheet 1 of 3 61301 12/08/2010 Rev. A

3

Position spacer plate (2) onto side of turret (1).
Align holes (A) on spacer plate and turret.
Install roll pin (3) into hole. Tap with hammer
until flush with surface on the outside of turret.
* You must install one spacer plate on each side of

turret. Spacer plates can be used on either side.

* Note: There are two notches in the spacer plates

they must be at the bottom.

Form: F205 Rev A 5-6-05

Installation Instructions

Trailer Forward

Note:

Shown w/Spacer Kit 61301 Installed

Figure 3

Figure 4

Trailer Forward

Sidewinder Turret

TM

Matching Wing Sets

For Wing Set Make and Model Numbers:
Lippert 1716
Lippert 1116
Lippert 0115
Use The Bolt Hole Locations Noted By The “B”
The pattern is a 8.75” horizontal & a 2.5” vertical

Note: Shown w/Spacer Kit 61301 Installed

For Wing Set Make and Model Numbers:
Fabex PB-500 Series
Note: For the 500 series only one row is needed.

(2 Bolts per Side)
Fabex PB-700 Series
Use The Bolt Hole Locations Noted By The “C”
The pattern is a 9.5” horizontal & a 2” vertical

Typical Bolting

Hardware Kit Contains: (8) 5/8-11x2 Gr.8 Bolts / (8) 5/8-11 Gr.8 Nuts / (8) 5/8 HD Flat Washers / (8) 5/8 Conical Lock Washers

Bolts & Flat Washers Are Installed From The Outside, Conical Lock Washers and Nuts On the Inside.
Torque All To 210 ft. lbs.

5/8-11 Gr.8 Nut

5/8 Conical Lock Washer

Typical Wing

5/8 HD Flat Washer

5/8-11x2 Gr.8 Bolt

 2009 Cequent Performance Products

Sheet 2 of 3 61301 12/08/2010 Rev. A

Form: F205 Rev A 5-6-05

Installation Instructions

other warranties, express or implied, including the warranty of merchantability or fitness for a particular purpose. If the

NOTES:

Sidewinder Turret

LIMITED FIVE YEAR WARRANTY

TM

1. Limited Warranty. Cequent Performance Products, Inc. (“We” or “Us”) warrants to the original consumer purchaser only

(“You”) that the product will be free from material defects in both material and workmanship for a period of five years, ordinary
wear and tear excepted; provided that installation and use of the product is in accordance with product instructions. There are no

product does not comply with this limited 5 year warranty, Your sole and exclusive remedy is that We will replace the product
without charge to You and within a reasonable time or, at our option, refund the purchase price. This warranty is not
transferable.

2. Limitations on the Warranty. This limited warranty does not cover: (a) normal wear and tear; (b) damage through abuse,

neglect, misuse, or as a result of any accident or in any other manner; (c) damage from misapplication, overloading, or improper
installation, including welds; (d) improper maintenance and repair; and (e) product alteration in any manner by anyone other than
Us, with the sole exception of alterations made pursuant to product instructions and in a workmanlike manner.

3. Obligations of Purchaser. To make a warranty claim, contact Us at 4774 Anchor Court West, Plymouth, MI, 48170, 1-888-521-

0510, identify the product by model number, and follow the claim instructions that will be provided. Any returned product that is
replaced or refunded by Us becomes our property. You will be responsible for return shipping costs. Please retain your purchase
receipt to verify date of purchase and that You are the original consumer purchaser. The product and the purchase receipt must be
provided to Us in order to process Your warranty claim.

4. Remedy Limits. Repair or replacement is Your sole remedy under this limited warranty or any other warranty related to the

product. We shall not be liable for service or labor charges incurred in removing or replacing a product or any incidental or
consequential damages of any kind.

5. Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s)

stated in the product instructions is at Your own risk.

6. Governing Law. This limited warranty gives You specific legal rights, and You also may have other rights which vary from state

to state. This limited warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of
law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes relating to this
warranty.

Cequent Performance Products - Towing Division

4774 Anchor Court West

Plymouth, MI 48170

 2009 Cequent Performance Products

Sheet 3 of 3 61301 12/08/2010 Rev. A

Form: F205 Rev A 5-6-05