Reely Cyclone245 FPV Instruction Manual

Item No. 1378384

t FPV Quadrocopter Cyclone 245 RtF WiFi

Version 12/15

INSTRUCTION MANUAL

CYCLONE 245 FPV

1

Part name: Upper
housing

Part name: Lower
housing

Part name: Circuit
board

Part name: Landing
skid

Part name: Carbon

bre spindle

Part name: Lithium
Battery

Part name: Rotor

blade

Part name: Bearing

Part name: CW
motor (red and

blue wire)

Part name: CCW

motor (black and
white wire)

Part name: Green light

Part name: Red light

Part name: Tail light
panel

Part name: Main gear

Accessories list (sold separately)

2

Blade x4

WATER GUN

CAMERA

BUBBLE GUN

WIFI FPV

5.8G FPV

Standard Accessories

NO

PART NAME QUANTITY

1

2

3

4

5

6

V686 Instruction Manual

V686 Aircraft

Charger

Li-Po battery

Blade

Remote control

1

1

1

1

4

1

Delivery content

3.7 V 730 mAh

Li-Po battery x 1

Charger x1

WIFI FPV

Optional Parts (sold separately)

MONITOR FPV

3

1. Age recommendation: Not for children under 14 years. This is not a toy.

2. Always operate your model in open spaces away from full-size vehicles, trafc and

people.

3. Always carefully follow the directions and warnings for this and any optional support
equipment ( chargers, rechargeable battery packs, etc.) .

4. Always keep all chemicals, small parts and anything electrical out of the reach of
children.

5. Always avoid water exposure to all equipment not specically designed and protected
for this purpose. Moisture causes damage to electronics.

6. Never place any portion of the model in your mouth as it could cause serious injury or
even death.

7. Never operate your model with low transmitter batteries.

8. Please note that you incur a penalty if you observe strangers with the camera installed

in the product without their knowledge and consent. Observe the provisions and
regulations of the country in which you use this product.

■

Read the ENTIRE instruction manual to become familiar with the features of the product

before operating. Failure to operate the product correctly can result in damage to the
product, personal property and cause serious injury. This is a sophisticated hobby product.
It must be operated with caution and common sense and requires some basic mechanical
ability. Failure to operate this Product in a safe and responsible manner could result in injury
or damage to the product or other property. This product is not intended for use by children
without direct adult supervision. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the
manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or
serious injury.

Warning

Additional Safety Precautions and Warnings

4

■

Thank you for choosing this REELY product. This four-axis aircraft can fly

outdoors, in order to make it easier and easier to control the aircraft, please
carefully read this manual before operating this aircraft, and please keep this
manual for any future adjustments and maintenance of reference you may

wish to make.

■

Before your first flight, please take the time to carefully read this
manual, which contains important flight information, which will help your
first flight to be a great success.

Accessories list ..................................................................................

Standard Accessories .........................................................................

Delivery Content ................................................................................

Optional parts ..................................................................................

Warning ..........................................................................................

Additional Safety Precautions and Warnings .................................................

Introduction ......................................................................................

Table of Contents ...............................................................................

Warning and the guide of using battery .......................................................

Battery Charging ................................................................................

First Flight Preparation CAUTION .............................................................

Binding instruction ..............................................................................

Transmitter Controls ............................................................................

First Flight instruction ..........................................................................

3D Rolling .......................................................................................

One key return to home ........................................................................

CF MODE .......................................................................................

CF mode Calibration ..........................................................................

Trouble shooting Guide .......................................................................

Schematic circuit board .......................................................................

Exploded View .................................................................................

Parts list ........................................................................................

Quadrocopter specications ..................................................................

Introduction

Table of Contents

7
8

9

9

10

10

10

10

11

12

13

13

4

4

5

6

7

1

2

2

3

3

2

4

5

The Battery Charger included

charges the Li-Po battery.

CAUTION: All Instructions and warnings must be followed exactly. Mishandling of Li-Po
batteries can result in a re, personal injury, and/or property damage.

1. By handling, charging or using the included Li-Po battery you assume all risks associated
with lithium batteries.

2. If at any time the battery begins to balloon or swell, discontinue use and disconnect
immediately. Continuing to use, charge or discharge a battery that is ballooning or swelling
can result in re.

3. Always store the battery at room temperature in a dry area for best results.

4. Always transport or temporarily store the battery in a temperature range between 5°C
to 48°C. Do not store the battery in the model or prolonged exposure to direct sunlight. If
stored in a high temperature environment, battery can be damaged or even catch re.

5. Never use a Ni-CD or Ni-MH charger. Failure to charge the battery with a compatible
charger may cause re resulting in personal injury and/or property damage.

6. Never exceed the recommended charge rate.

7. Never cover warning labels with hook and loop strips.

Only use the charger supplied by our company. Do not use a 12V power
supply or property damage and Injury could occur.

Warning and the guide of using battery

WARNING:

Notice: When a LiPo battery is discharged below 3.3V, the battery may be damaged

and may no longer accept a charge. Please land the quadrocopter
immediately and recharge the battery.

Always use a charger

compatible with

batteries.

Always charge

Batteries away from

ammable materials.

Never leave charging
Batteries unattended.

Never charge

damaged Batteries.

Never Alter Batteries. Never touch or use

hot Batteries.

CAUTION WARNING WARNING

WARNING

WARNING

WARNING

It has been designed with
safety in mind.

6

1. Before taking the quadrocopter into operation, ensure that the ight

battery is charged completely and the batteries in the transmitter still have
enough voltage.

2. Before powering on remote controller, please keep the joystick for the
pitch function in the bottom position.

3. Please ensure quadrocopter is successful binded before operation. First

connect the ight battery to the quadrocopter electronics plug connection
with protection against polarity reversal. The LED on the quadrocopter
ashes quickly, then switch on the remote control transmitter with the
function switch. This starts the binding process, after which transmitter
and receiver use the same digital code. If binding is completed, the LED
remains lit.

4. Do not take any risks when operating the product! Your own safety and
that of your environment is solely down to you being responsible when
dealing with the model. Improper operation may cause serious injury and
property damage! Therefore make sure to keep a sufciently safe distance
to persons, animals or objects during operation.

Notice: Only use the charger provided
Notice: Never attempt to power the charger from an AC outlet without the use

of a proper AC to DC adapter/ power supply.

3.7V 730mah

Charging line

LED

1-cell 3.7V Variable Rate DC Li-Po Charger

Instruction:

Please only recharge LiPo ight battery with the supplied AC

charger. Connect the battery to charger wire as per below
illustration only.

Battery Charging

First Flight preparation CAUTION

7

Place the quadrocopter on a level surface.

Move the joystick for the pitch function to
the lowest setting and switch the transmit­ter on with the on/off switch. Then push the
joystick all the way forward and then slowly

backward again to switch the transmitter
into operating mode. The transmitter emits

a single signal sound to conrm binding is
complete, and the LED remains lit.

Li-Po

3.7V 730mAh

Remove the ight vehicle battery safely
at the conclusion of the ight. This
should become a post-ight habit to

guard against unforeseeable problems.

Warning: If left connected in the ight

vehicle for a long time, the battery may be
damaged due to over-discharge, or even

become a re hazard.

Turn off the transmitter. If transmitter
is not to be used for a long duration,
please remove the battery for storage.

Warning: If the AA batteries are left
in the transmitter, potential leakage
could occur which may damage the

transmitter, and create re hazards.

If transmitter is not to be

used for a long time, please
remove the battery for

storage.

BINDING OF RADIO TRANSMITTER AND RECEIVER

Step1

Step2

Step3

Step4

Li-Po

3.7V 730mAh

Push the throttle stick
to the lowest position

CAUTION

8

1. Transmitter Control

LCD Display

Power LED

Camera (CF mode press &

hold for 2 seconds)

Aileron trim

Power Switch

Antenna

Roll

Steering sensitivity

indicator: 80%

X-axis calibration key / Steering
sensitivity indicator: 40%

Throttle trim indicator

Rudder trim indicator

Transimitter battery indicator

Stick modes indicator

Transmitter Control

2. LCD Display

Video

Throttle Control stick

Throttle trim

Rudder trim

Y-axis calibration key / Steering
sensitivity indicator: 60%

Elevator Control stick

Elevator trim

Steering sensitivity indicator: 100%

One key to return home / Light control

Stick modes indicator

Elevator trim indicator

Aileron trim indicator

9

Climb Descend

Nose Yaws Left

Nose Yaws Right

Elevator up Forward

Elevator

down

Throttle up Throttle down

Rudder
Left

Rudder
right

Ailerron left Ailerron right

Left Right

Stable exible, ight routes,

Drift, 3D to roll easily

Once you have mastered all basic controls, then should you proceed and attempt more
difcult maneuvers such as 3D roll. To activate 3D roll function, press top right switch
button, the transmitter will emit a single continuous sound to conrm quadrocopter is in 3D
roll mode. Move the joystick for nick and roll function quickly in the direction in which the
quadrocopter should roll and immediately bring the joystick back to the center position.

Attention: If you do not move the deected joystick back to center position quickly enough,
the quadrcopter may execute 2 rolls in succession and thereby lose considerable altitude.

If quadrocopter is in CF mode, 3D roll cannot be activated.

Throttle

Rudder

Elevator

Aileron

If you are not familiar with the controls of your V636, take a few minutes
to familiarize yourself with them before attempting your rst ight.

First Flight instruction

3D Rolling

Backward

10

Press and hold light control switch button for 2 seconds. Transmitter will emit a single continuous
sound to conrm, rear light will blink quickly at the same time. Quadrocopter begins to return home.

Note: Please note one key return to home will not work if 1.) during start up, stand behind
quadrocopter and that the quadrocopter is not aligned with the green propellers facing forward. 2.)
If you have changed to CF mode during ight.

Press and hold CF mode switch button for 2 seconds. Transmitter will emit a continuous sound to
conrm.
For you to be able to use CF mode correctly, it is necessary for you to always stand behind the
quadrocopter and look in the direction in which you aligned the quadrocopter before the start. The
quadrocopter must be aligned with the two green propellers facing forward.

The quadrocopter has a compass that allows it to detect its direction and that it needs for ight
in CF mode. The compass comes pre-calibrated from the factory, but for each use in a new ight
area, it needs to be recalibrated.

To do this, proceed as follows:

1. As described above, rst start up the transmitter and then the model. The joystick for the
throttle function must be in the lowest position so that the motors do not start running.

2. Place the quadrocopter on a level surface.

3. Press and hold the 40% switch button until the LEDs on quadrocopter begin to ash and thus

indicate the calibration mode.

4. Now turn the quadrocopter, as seen from above, clockwise until the LEDs remain lit.

5. Press and hold the 60% switch button LEDs begin to ash again.

6. Now hold the quadrocopter with the front side (green propeller) vertically on top and turn it

clockwise again until the LEDs remain lit again.

7. The calibration is thereby successfully completed.

One Key return to home

CF MODE

CF mode Calibration

Troubleshooting Guide

Problem Problem cause Solution

1

Receiver status LED blinks
continuously for more than
4 seconds after ight battery
Inserted. No response to control
Input.

Unable to bind to transmitter. Repeat the power up initializing

process. (Refer to P.6:Binding of
radio transmitter and receiver.

2

No response after battery is
connected to quadrocopter.

1. Power to the transmitter and
receiver.

2. Check the transmitter and
receiver voltage.

3. Poor contact on battery
terminals.

1. Turn on transmitter and ensure

ight battery Is Inserted properly.

2. Use fully charged batteries.

3. Re-seat the battery and ensure
good contact between battery
contacts.

3

Motor does not respond to throttle

stick, LED receiver ashes.

Flight battery depleted. Fully charge the battery, or

replace with a fully charged
battery.

4

Main rotor continue to spin after
landing.

Throttle trim accidentally

Increased during ight.

Conrm throttle trim is in centre

or slightly below.

11

Tail LED socket

LED socket (M3)

Motor socket

(M2, M3)

LED socket (M4)

LED socket (M1)

Schematic circuit board

LED socket (M2)

Motor socket

(M4, M1)

5

Main rotor spins but unable
to takeoff.

1.

Rotor blades damaged

2. Flight battery depleted

1. Replace main blades

2. Charge or replace with a fully
charged battery.

6

Strong vibration of
quadrocopter.

1.Rotor deformation 1. Replace the rotor

7

Quadrocopter drifts sideways
despite trim adjustment or
Inconsistent speed during
left/right pirouette.

1. Damaged tall rotors

2. Damaged tail drive motor

Replace the rotor

Replace the main motor

8

Quadrocopter still drifts
forward despite trim
adjustment.

quadrocopter not initialized on a

level surface or correctly aligned

Disconnect the ight battery, center

all control trims and start up the
quadrocopter again

9

Quadrocopter cannot take off
after a crash.

1. Motor fall out

2. Gear loosen

1. Install the motor again

2. Tighten the gear

10

Large deviations headless

mode.

1. quadrocopter not initialized on a
level surface or correctly aligned.

2. CF mode disrupted

1. Start up the quadrocopter again with

correct alignment

2. Re calibrate CF mode (refer section on
CF calibration)

12

Green B

Green A

Black B

Black A

forward

Exploding View

13

NO PART NAME QUANTITY

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Propeller guard

Main rotor blade

Upper housing

Receiver board

Bearing

Battery cover

Battery

Electric motor

LED light

LED light cover

Lower housing

Carbon bre spindle

Tail light plate

Bearing

Tail LED

Landing skid

4

4

1

1

8

1

1

4

4

4

1

4

1

4

1

2

Parts Listing

Quadrocopter specications

Length

Height

Blade length

Battery Specication

Flight time

375 mm

58 mm

136 mm

3.7V 730mAh23C

7-8 min

Live Video Streaming and ight

control via WiFi

This quadrocopter comes with a WiFi camera already pre-installed. The device uses advanced image
compression technology to enable you to stream live video on your smartphone at a distance of 50 to 70

meters using WiFi.

To utilize this powerful Live video streaming feature and also ight control via smartphone , simply
download and install the app by scanning the QR code shown on following page matching to your

smartphone operating system.

Operating instruction:

To stream live video with WiFi camera, please ensure to take camera connector wire and plug it into the
appropriate socket with marking “WiFi” etched on quadrocotper housing. Socket is located adjacent to
camera. Please note, if connector wire is not correctly and securely inserted into the socket, live video
streaming feature will not work and may fail.
Power on your transmitter and the quadrocopter, and then the app on your smartphone.
From the Wi-Fi settings control on your smartphone, search for WiFi network name beginning with
“WiFiUFO” and enable connect ion.
Start the app and then press play on screen. The default app setting allows only for video transmission
but is disabled for ight control capability.
Mount the smartphone holder as per illustration on following page.
Place your smartphone on the smartphone holder, and use onscreen controls as shown below to stream
live video or take photos.
To use your smartphone to control ight of quadrocopter, simply press control switch button to
interchange between transmitter control/ phone control.

App Controls

Steering sensitivity value

View le from folder

Picture Video

Return

Gravity sensor mode

Control switch (transmitter control /
phone control)

Screen rotation

Analog sticks

Rudder trim

Elevator trim

Aileron trim

Phone Holder assembly

WIFI Webcam Phone Holder

(Illustration)

QR code for

IOS

WIFI UFO

QR code for

(GooglePlay Android)

WIFI UFO

(GooglePlay)

Technical specication

Function

Camera

Video encoding format

Video sampling

Image Resolution

Transmitting frequency range

Supports standard

Transmission bit rate

Throughput

Transmission power

54M: 15dBM

11M: 19dBM

Receiver sensitivity

11M:-85dBM@8%PER

6M:-88dBM@10%PER

1M:-90dBM@8%PER

Safety standard

Transmission distance

50 to 150 m (varies depending on surrounding

electromagnetic interference)

Antenna Selection

PCB size 33mm * 22mm * 0.8mm

Supply voltage

Current consumption

Operating temperature

H.264

0.3 megapixel

Specications

rate of 25 to 30 frames per second

VGA (640*840)

2.412-2.484 GHz

support WI-FI 802.11 b / g / n standards

135/54/48/36/24/18/12/9/6 1M ( adaptive )

90Mbps

135M: 15dBM

54/135M:-72dBM@10%PER

WEP/WPA-PSK/WPA2-PSK

IPX 1 generation antenna interface

3-5V

about 800mW

-10°C~+70°C