Reece Milli Edge MKII Instructions Manual

MILLI

900

800

1050

950

100

150

50

25

1320

EDGE MKII HEATED TOWEL RAILS
1320 HEIGHT

450

350

900

600

500

1050

750

650

100

150

1320

800

950

Dimensions are nominal measurements only.
Measurements shown in Millimetres.

SPECIFICATIONS

Recommended Use

Materials

Finish

Technology

Element

Options

Power Entry

Voltage

Wattage

Heating Time

Standards

Safety Rating

Additional Features

Options

Domestic Hotel and Commercial

Stainless Steel

Polished Stainless Steel

Dry Element

Electrical Element- (Replaceable)

Hardwired Only

Any Leg

12V

450-58W, 600-81W, 750-103W, 900-136W, 1050-147W

30 Minutes

AS/NZ 60335.2.43

IPX5

Made in Australia

Non Heated Versions available

50

25

To see the complete MILLI range go to
www.reece.com.au/bathrooms

CLEANING RECOMMENDATIONS

We recommend the use of soapy water or approved cleaners.

This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade
people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range
without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at
time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

MILLI

Installation Guide

Milli Edge Mk2 Towel Ladders – Heated

Models: Milli Edge 420, Milli Edge 720, Milli Edge 1020, Milli Edge 1320
Version: 6.00 Standard: (AS/NZS 60335.2.4)

EDGE MKII HEATED TOWEL RAILS
1320 HEIGHT

INSTALLATION INSTRUCTIONS

OVERVIEW

Thank you for choosing AVENIR Bathroom Accessories and for supporting an Australian designed and manufactured product.

PLEASE TAKE NOTE: The installation procedure for Avenir products may be different from other products and may not be common knowledge.
Please read this installation guide carefully. Experience has shown that most issues arise as a result of either our installation procedure not being
followed or the supplied fixings not being used. Please use the supplied fixings as they have been carefully selected and tested to suit the
application. Our warranty covers only manufacturing and workmanship defects, not application suitability or issues with installation.

AVENIR Milli Edge towel ladders are designed to suit stud walls with tiles or masonry walls. Non-masonry walls with no tiles will require a timber
substrate directly behind each point where the ladder is fixed to the wall. In this case follow the procedure below, with the exception that no wall plugs
are required.

SAFETY

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure they do not play with the appliance. This appliance is a low voltage device and can be installed zones 1, 2 or 3 in the
bathroom. This appliance must be installed, serviced and maintained by a qualified electrician.

WARNING: In order to avoid hazards for young children, this appliance should be installed so that the lowest rail is at least 600mm above the floor.

ELECTRICAL

The power to this appliance is supplied by a safety-isolating transformer. Wiring connection points are available on one side the heated towel

ladder through either the top or the bottom mounting legs – In order to make the connection on the opposite side it is necessary to turn the ladder
upside down (the ladder design is symmetrical). Your electrician must install an isolating switch and/or timer in order to control the mains supply to the
safety-isolating transformer.

PRE INSTALLATION REQUIREMENTS

• Provision must be made for a ventilated, serviceable location of the supplied safety-isolating transformer. The supplied 2-core wire must be
installed from the safety-isolating transformer to the installation location of the heated towel ladder (any leg). This wiring should be concealed
inside the wall and should protrude through a hole in the wall surface (minimum 150mm protrusion) at the position of any one of the four
mounting legs of the heated towel ladders’ intended location.

• The heated towel ladder mounting legs covers an area of 20mm x 40mm. It is therefore essential that the hole in the wall surface where the wire
protrudes is no more than 12mm diameter to ensure that the mounting leg covers the hole completely.

• Provision should be made for a timer to control the mains supply to the safety-isolating transformer. If no timer is used (not recommended) then
an isolating switch must be installed by your electrician.

PLEASE TAKE NOTE: USE THE SUPPLIED WIRE – For ladders < 120W a 2 meter length of 15 AWG (1.65mm2) wire is supplied. For ladders >

120W a 2 meter length of 12 AWG (3.3mm2) wire is supplied – Extending this wire will reduce the rail heat.

TOWEL LADDER TEMPERATURE

How hot should my towel ladder be: The temperature of the towel ladder will vary depending on factors like the ambient temperature, how many

towels are covering the rails, and the moisture content of the towels. On a cold day with no towels on the rails, the ladder will feel only lukewarm to the
touch. On a hot day with thick dry towels covering the rails completely, the ladder will be very hot to the touch – to the point where it will feel very
uncomfortable to continue to keep your hand on the rail. Only the horizontal rails are heated.

Towel ladder too cold: Please note that the horizontal heated rails of the ladder have a surface area of more than twice that of conventional heated
towel rails (round or square tubular rails). It is for this reason that if no towel is draped over the heated towel ladder, the rails will cool substantially and
will not remain hot to the touch. Full temperature will only be achieved when there is a towel covering the rails.

Towel ladder too hot: The temperature of the ladder may be reduced using a light dimmer or an Eco Timer connected to the safety-isolating
transformer if required.

USE THE SUPPLIED LOW VOLTAGE WIRE

EXTENDING THIS WIRE WILL RESULT IN REDUCED HEAT

Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference