Reece HENDEN HSSP200, HENDEN HSSP300, HENDEN HSSP420 Installation & Owner's Manual
Single Speed Pump
HSSP200, HSSP300, HSSP420
INSTALLATION &
OWNERS MANUAL
WARNING:
Failure to
follow these
instructions and
comply with
all applicable
codes may
cause serious
bodily injury
and/or property
damage.
The installation
of this product
should be carried
out by a person
knowledgeable
in swimming
pool plumbing
requirements
following the
installation
instructions provided
in this manual.
IMPORTANT
Please read carefully
Please install
and maintain the
products according
to AS 3633, AS/
NZS 60335.2.41,
3000 standard
when the product
is used in Australia.
Please pass these instructions on to the operator of this equipment
Please install
and maintain
the products
according to
EN 60335-2-41
standard
and local
standard when
the product is
used in Europe.
The HSSP200,
HSSP300 and
HSSP420 can be
connected only to a
supply with system
impedance no more
than 0.381 ohm.
In case necessary,
please consult your
supply authority for
system impedance
information.
If the supply
cord of this
product is
damaged
it must be
replaced by
Henden or the
manufacturer,
with genuine
Henden
spares.
Contents
Henden Single Speed Pump
INSTALL ATION
1. BEFORE YOU USE THIS PUMP 4
2. YOUR HENDEN SINGLE SPEED POOL PUMP 4
3. HENDEN SINGLE SPEED POOL PUMP – HYDRAULIC
PERFORMANCE 5
4. LOCATION OF THE PUMP 6
5. WEATHER PROTECTION 6
6. POWER CONNECTION 6
7. TYPICAL INSTALLATION DIAGRAM 7
8. DIMENSIONS 7
9. PIPE CONNECTION 7
OWNERS MANUAL
10. STARTING THE PUMP 8
11. PUMP OPERATION 8
12. EMPTYING THE STRAINER BASKET 8
13. TROUBLE SHOOTING 8
14. REMOVAL OF THE PUMP FROM PIPEWORK 9
15. WATER QUALITY 9
16. HENDEN
™
REPAIR OR REPLACEMENT GUARANTEE 10
HENDEN INSTALLATION & OWNERS MANUAL | 3
Henden Single Speed Pump Installation Manual
INSTALLATION
1. BEFORE YOU USE THIS PUMP:
• Please ensure the pump is installed in a safe
environment
• The pump enclosure has adequate drainage in the
event of leakage
• The pipe-work is correctly sealed and supported
• The pump is primed correctly
• The power supply is correctly connected
• All steps have been taken for safe operation
Appropriate details for all of these items are contained
in the following Installation and Operating Instructions.
Read these in their entirety before switching on this pump.
If you are uncertain as to any of these Installation and
Operating Instructions please contact your Henden after
sales team or the appropriate Reece Irrigation & Pools
branch as listed on the back of this document.
2. YOUR HENDEN SINGLE SPEED
POOL PUMP
Congratulations on your purchase of a quality product
from the Henden range of pool equipment. You
are assured of many years of reliable and efficient
performance from Henden.
The Henden Single Speed pool pump has been designed
to circulate swimming pool water in conditions set out in
the Australian Standard for swimming pool water quality
(AS 3633) or equivalent. They should not be used for any
other purpose without first consulting Henden.
Every Henden Single Speed pool pump is thoroughly
tested against a number of pressures, voltage, current
and mechanical performance parameters. Henden’s
advanced pump manufacturing technology provides
reliable and efficient pumping performance that lasts
and lasts.
THIS APPLIANCE IS NOT TO BE USED BY PERSONS
(INCLUDING CHILDREN) WITH REDUCED PHYSICAL,
SENSORY OR MENTAL CAPABILITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE
BEEN GIVEN SUPERVISION OR INSTRUCTION CHILDREN
BEING SUPERVISED NOT TO PLAY WITH THE APPLIANCE.
THE SUPPLY CORD CANNOT BE REPLACED. IF THE CORD
IS DAMAGED THE APPLIANCE SHOULD BE SCRAPPED.
DO NOT DISPOSE OF ELECTRICAL APPLIANCES
AS UNSORTED MUNICIPAL WASTE, USE SEPARATE
COLLECTION FACILITIES.
CONTACT YOUR LOCAL GOVERNMENT FOR INFORMATION
REGARDING THE COLLECTION SYSTEMS AVAILABLE.
IF ELECTRICAL APPLIANCES ARE DISPOSED OF IN
LANDFILLS OR DUMPS, HAZARDOUS SUBSTANCES CAN
LEAK INTO THE GROUNDWATER AND GET INTO THE FOOD
CHAIN, DAMAGING YOUR HEALTH AND WELL-BEING.
4 | HENDEN INSTALLATION & OWNERS MANUAL
Loading...