Page 1
Visit our website at
www.reebokhomefitness.com
new products, prizes,
fitness tips, and much more!
Model No. RBBE0405.0
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
USER’S MANUAL
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.reebokservice.com
CAUTION
Read all precautions and instruc
tions in this manual before using
this equipment. Save this manual
for future reference.
-
Page 2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
I
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.
WARNING DECAL PLACEMENT
The decal shown here has
been placed on the weight
bench. If the decal is missing or illegible, please call
the toll-free telephone
number on the front cover
of this manual and order a
free replacement decal.
Apply the decal in the
location shown.
REEBOK and the Vector Logo are registered trademarks and service marks of Reebok. This product is
manufactured and distributed under license from Reebok International.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual and all
arnings on the weight bench before using
w
the weight bench. Use the weight bench only
as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench.
5. Keep hands and feet away from moving parts.
6. Inspect and properly tighten all parts regulary. Replace any worn parts immediately.
l
7. Keep children under 12 and pets away from
the weight bench at all times.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. The weight bench is designed to support a
maximum user weight of 300 pounds. Do not
use more than 110 pounds of weight with the
weight bench. Note: The weight bench does
not include weights.
10. Always make sure that the locking pin is fully
inserted into the pivot bracket and the bench
frame before exercising.
11. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Page 4
BEFORE YOU BEGIN
Thank you for selecting the versatile REEBOK
ADJUSTABLE BODY TONING BENCH weight bench.
The weight bench is designed to help develop the
major muscle groups of the upper body. Whether your
oal is to tone your body, build dramatic muscle size
g
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
reading this manual, see the front cover of this manu-
Seat
®
al. To help us assist you, please note the product
model number and serial number before calling. The
model number is RBBE0405.0. The serial number can
be found on a decal attached to the weight bench (see
he front cover of this manual).
t
To avoid a registration fee for any service needed
under warranty, you must register the weight
bench at www.reebokservice.com/registration.
Before reading further, review the drawing below and
familiarize yourself with the parts that are labeled.
Backrest
Front Leg
Foam Pad
Pivot Bracket
ASSEMBLED DIMENSIONS:
Height: 40 in. / 102 cm
Width: 18 in. / 46 cm
Depth: 52 in. / 132 cm
4
Page 5
ASSEMBLY
Make Things Easier for Yourself
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
To hire an authorized service technician to
assemble the weight bench, call toll-free
1-800-445-2480.
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two people.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1.
Before assembling this product, make sure
that you understand the information in the
box above.
Press two 56mm Round Outer Caps (14) onto the
Front Stabilizer (1).
Attach the Front Stabilizer (1) to the Front Leg (2)
with two M8 x 67mm Carriage Bolts (21) and two
M8 Nylon Locknuts (18). Make sure the indents
in the Stabilizer and the decal on the Front Leg
are in the positions shown. Do not tighten the
Locknuts yet.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly may require the following tools (not
included):
• two adjustable wrenches
• one rubber mallet
• one standard screwdriver
• one Phillips screwdriver
• lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1
2
Name
Decal
18
18
14
1
14
Indents
21
5
Page 6
2. Press two 56mm Round Outer Caps (14) onto the
Rear Stabilizer (5).
Make sure the indents and the decal on the
ear Stabilizer (5) are oriented as shown.
R
Attach the Rear Stabilizer to the Bench Frame (4)
with two M8 x 67mm Carriage Bolts (21) and two
M8 Nylon Locknuts (18). Do not tighten the
Locknuts yet.
2
8
1
4
14
18
5
arning
W
Decal
ndents
I
21
14
3. Attach the Seat Frame (3) to the Bench Frame
(4) with two M8 x 63mm Bolts (25), two M8
Washers (20), and two M8 Nylon Locknuts (18).
Do not tighten the Locknuts yet. Make sure
that the bolt heads rest inside the holes in the
top of the Bench Frame.
4. Attach the Seat Frame (3) to the Front Leg (2)
with two M8 x 71mm Bolts (24), two M8 Washers
(20), and two M8 Nylon Locknuts (18).
Tighten the M8 Nylon Locknuts (18) used in
steps 1, 2, and 4. Then, tighten the M8 Nylon
Locknuts (18) used in step 3.
3
25
4
3
20
18
4
20
18
20
20
24
3
24
Orient a Backrest Frame (7) with the indicated
5.
hole closer to the bottom of the Frame. Attach the
Frame to the Pivot Bracket (6) with two M8 x
43mm Bolts (26), two M8 Washers (20), and two
M8 Nylon Locknuts (18). Do not tighten the
Locknuts yet.
Attach the other Backrest Frame (7) to the
Pivot Bracket (6) in the same manner
.
2
5
7
7
Hole
20
6
20
18
26
6
Page 7
6. Attach the Backrest (9) to the Backrest Frames
(7) with four M6 x 37mm Screws (27) and four M6
ashers (30). M
W
ented as shown. Do not tighten the Screws
et.
y
ake sure the Backrest is ori-
6
9
7
7. Insert the Pivot Bracket (6) through the slot in the
Bench Frame (4).
Grease the M10 x 187mm Bolt (28) with the
included grease packet. Attach the Backrest
Frames (7) to the tube on the Bench Frame (4)
with the Bolt, two M10 Washers (19), and an M10
Nylon Locknut (17).
Locknut; the Backrest Frames must be able to
pivot easily.
Tighten the M8 Nylon Locknuts (18) used in
step 5, and the four M6 x 37mm Screws (27)
used in step 6.
8. Attach the Locking Pin (15) to the Bench Frame
(4) with an M4 Washer (31) and an M4 x 16mm
Self-tapping Screw (22). Insert the Pin through
the Bench Frame and the Pivot Bracket (6).
Do not overtighten the
30
30
27
7
19
Tube
7
6
17
8
30
27
Slot
4
19
28
Grease
30
9. Attach an M8 x 15mm Bolt (29) to the Pivot
Bracket (6) with an M8 Nylon Locknut (18).
4
15
31
6
9
6
18
29
22
7
Page 8
10. Attach the Seat (8) to the Seat Frame (3) with
four M6 x 16mm Screws (23).
10
8
3
11. Insert a Pad Tube (10) into the Front Leg (2).
Slide two Foam Pads (11) onto the ends of the
Pad Tube.
Assemble the other Pad Tube (10) to the Front
Leg (2) in the same manner.
12. Make sure all parts are properly tightened
before the weight bench is used.
11
11
23
23
10
2
10
11
.
8
Page 9
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 10 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
ake sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
M
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
To adjust the Backrest (9), remove the Locking Pin
(15) from the Bench Frame (4). Move the Backrest to
the desired position and reinsert the Locking Pin into
the Bench Frame and an adjustment hole in the Pivot
Bracket (6).
WARNING: Always make sure the
Locking Pin (15) is fully inserted through the
Bench Frame (4) and the Pivot Bracket (6).
9
4
15
6
Adjustment
Holes
9
Page 10
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
o increase the size and strength of your muscles,
T
push them close to their maximum capacity. Your muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of resistance for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of resistance that is
right for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of resistance.
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of resistance and increase the number of repetitions in each set. Complete as many sets of 15 to
20 repetitions as possible without discomfort. Rest for
1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of
resistance.
Weight Loss
To lose weight, use a low amount of resistance and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross T
Cross training is an efficient way to get a complete and
well-balanced fitness program. An example of a balanced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise cycle
or an elliptical exerciser, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of strength training and aerobic exercise will reshape and strengthen your body, plus develop your heart and lungs.
raining
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
s well as the number of repetitions or sets completed,
a
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
-
10
Page 11
Rest for a short period of time after each set. The
O
P
Q
R
S
T
U
V
X
W
N
M
J
G
F
H
I
K
E
C
D
B
A
L
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
ideal resting periods are:
Rest for three minutes after each set for a muscle
•
building workout.
Rest for one minute after each set for a toning work-
•
out.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
ithout strain. Stretching at the end of each workout
w
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to achieving the greatest results is to make exercise a regular
and enjoyable part of your everyday life.
11
Page 12
M10 x 187mm Bolt (28)
M8 x 63mm Bolt (25)
M6 x 37mm Screw (27)
M6 x 16mm Screw (23)
M6 Washer (30)
M10 Nylon Locknut (17)
M8 Nylon Locknut (18)
M4 x 16mm Self-tapping Screw (22)
M8 x 15mm Bolt (29)
M8 Washer (20)
M8 x 67mm Carriage Bolt (21)
M8 x 43mm Bolt (26)
M8 x 71mm Bolt (24)
M4 Washer (31)
M10 Washer (19)
PART IDENTIFICATION CHART
efer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
R
ing is the key number of the part, from the PART LIST.
If a part is not in the parts bag, check to see if it has been pre-attached.
Note: Some small parts may have been pre-attached.
Page 13
PART LIST—Model No. RBBE0405.0 R0605B
Key No. Qty. Description Key No. Qty. Description
1 1 Front Stabilizer
2 1 Front Leg
3
4 1 Bench Frame
5 1 Rear Stabilizer
6 1 Pivot Bracket
7 2 Backrest Frame
8 1 Seat
9 1 Backrest
10 2 Pad Tube
11 4 Foam Pad
12 4 19mm Round Inner Cap
13 1 56mm Round Inner Cap
14 4 56mm Round Outer Cap
15 1 Locking Pin
16 4 25mm Square Inner Cap
17 1 M10 Nylon Locknut
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
1 Seat Frame
18 13 M8 Nylon Locknut
19 2 M10 Washer
0 8 M8 Washer
2
21 4 M8 x 67mm Carriage Bolt
22 1 M4 x 16mm Self-tapping Screw
23 4 M6 x 16mm Screw
24 2 M8 x 71mm Bolt
25 2 M8 x 63mm Bolt
26 4 M8 x 43mm Bolt
27 4 M6 x 37mm Screw
28 1 M10 x 187mm Bolt
29 1 M8 x 15mm Bolt
30 4 M6 Washer
31 1 M4 Washer
# 1 User’s Manual
# 1 Exercise Guide
# 1 Grease Packet
Page 14
18
9
16
6
7
27
26
20
26
20
17
19
16
27
19
28
18
18
8
12
11
10
11
12
10
1111
111111
111111
12
12
14
14
21
18
18
20
13
23
23
3
18
25
4
15
14
14
21
5
22
24
24
4
18
29
1
18
20
20
24
18
2
30
30
30
30
31
EXPLODED DRAWING—Model No. RBBE0405.0 R0605B
Page 15
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
he following information:
t
1. the MODEL NUMBER of the product (RBBE0405.0)
2. the NAME of the product (REEBOK ADJUSTABLE BODY TONING BENCH weight bench)
3. the SERIAL NUMBER of the product (see the front cover of this manual)
4. the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. If the product is shipped to a service center,
freight charges to and from the service center will be the customer’s responsibility. For in-home service, the
customer will be responsible for a minimal trip charge. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center; products used for commercial or rental purposes;
or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
-
-
ou may also have other rights which vary from state to state.
This warranty gives you specific legal rights.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 228203 R0605B Printed in China © 2004 ICON IP, Inc.
Y
Loading...