Red Lion SLX-6RS-1, SLX-6RS-4, SLX-6RS-5, SL-6RS-1, SL-6RS-4 Data Sheet

SL/SLX-6RS-1/4/5 Industrial Ethernet Switch

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

SL

SLX

SL

SLX

6 PORT INDUSTRIAL ETHERNET RING SWITCH

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

The SL/SLX-6RS is a 6 port industrial Ethernet switch
featuring Sixnet’s Real-Time-Ring™ which provides very
fast, fault-tolerant network redundancy and prioritized
message delivery needed in critical real-time systems.

These Rings self-congure and just run, without the
complex conguration steps required by alternative
solutions. This advanced technology delivers reliability
and performance, saves you money, and makes your job

easier.

PRODUCT HIGHLIGHTS

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

SL

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

6 PORT INDUSTRIAL ETHERNET RING SWITCH

SL/SLX-6RS-1/4/5

PRODUCT DATASHEET

The SL/SLX-6RS is a 6 port industrial Ethernet switch
featuring Sixnet’s Real-Time-Ring™ which provides very
fast, fault-tolerant network redundancy and prioritized
message delivery needed in critical real-time systems.

These Rings self-congure and just run, without the
complex conguration steps required by alternative
solutions. This advanced technology delivers reliability
and performance, saves you money, and makes your job

easier.

Sixnet Networking Series

6 Port Industrial Ethernet Ring Switch

n

6 ports including up to 2 ber optic

n

Super-fast, fault-tolerant ring redundancy

n

Pre-congured for true plug & play simplicity

n

Truly industrial hardened design

n

Slim case for DIN rail or direct panel mounting

REAL-TIME FAULT-TOLERANT RINGS

n

Recovery time of 30 mS plus 5 mS per hop!

n

Ideal for deterministic systems and PLCs

n

Real-time Modbus over Ethernet monitoring

REAL-TIME TRAFFIC PRIORITIZATION (QoS)

n

Assure delivery of real-time data

n

Improve network utilization

n

User settable priority assignments

MANAGED SWITCH FEATURES – at a lower cost

n

User congurable port settings

n

Port mirroring for trafc diagnostics

n

Message ltering to prevent broadcast storms

TROUBLE FREE OPERATION

n

Ultra-reliable 1,000,000 + hours MTBF

n

-40 to +85 °C operating range (SLX model)

n

UL/CSA (CUL), CE and Hazloc (Zone 2) rated

n

Dual (redundant) power inputs

n

Industrial surge and spike protection

n

Self-test/alarm output contact

SL

SLX

SLX

SL/SLX-6RS-1/4/5 Industrial Ethernet Switch Specifications

SL/SLX-6RS-1/4/56 PORT INDUSTRIAL ETHERNET RING SWITCH

ENVIRONMENTAL

STANDARDS COMPLIANCE

PHYSICAL

SL/SLX-6RS-1/4/56 PORT INDUSTRIAL ETHERNET RING SWITCH

ORDERING GUIDE

SLX-6RS-1-D1 6 RJ45 ports, metal case, wide temp.

SLX-6RS-4SC-D1 4 RJ45 ports, 2 multimode SC, 4 km

SLX-6RS-4ST-D1 4 RJ45 ports, 2 multimode ST, 4 km

SLX-6RS-5SC-D1 4 RJ45 ports, 2 singlemode SC, 20 km

SLX-6RS-5ST-D1 4 RJ45 ports, 2 singlemode ST, 20 km

SLX-6RS-5SCL-D1 4 RJ45 ports, 2 singlemode SC, 40+ km

SLX-6RS-5STL-D1 4 RJ45 ports, 2 singlemode ST, 40+ km

SL- w/ Lexan case and limited temperature

Setup Wizard Free - Windows conguration tool

ET-PS-024-02 Power supply – AC to 24VDC, 2A

SP-ETH-2 Dual port Ethernet surge & lightning

protector for 10/100 ports

ENVIRONMENTAL

n

Operating temperature:

p

SLX: -40 to +85 °C (cold startup at -40 °C)

p

SL: -40 to +60 °C

n

Storage temperature -40 to +85 °C

n

Humidity (non-condensing) 5 to 95% RH (optional
conformal coating is available)

n

Vibration and shock – IEC60068-2-6, -27

n

Maximum Operating Altitude: 30,000 ft.

STANDARDS COMPLIANCE

n

Electrical safety – UL508 / CSA C22.2/142; EN61010-1, CE

n

EMC – FCC part 15, ICES-003; EN61000-6-2/4, CE

n

Hazardous locations – ANSI/ISA 12.12.01 / CSA C22.2/213

(Class I, Div. 2); EN60079-15 (Zone 2, Category 3),
CE (ATEX)

n

Maritime – designed for marine and offshore per ABS

n

RoHS and WEEE compliant

PHYSICAL

n

DIN rail or direct panel mounting

n

Case – Aluminum (SLX) or Lexan (SL)

n

Ingress protection

p

SL models: IP30

p

SLX models: IP40

n

Weight – SLX: 0.23 kg (8 oz.); SL: 0.17 kg (6 oz.)

n

Dimensions – see mechanical diagram

SL/SLX-6RS-1/4/56 PORT INDUSTRIAL ETHERNET RING SWITCH

ENVIRONMENTAL

n

Operating temperature:

p

SLX: -40 to +85 °C (cold startup at -40 °C)

p

SL: -40 to +60 °C

n

Storage temperature -40 to +85 °C

n

Humidity (non-condensing) 5 to 95% RH (optional
conformal coating is available)

n

Vibration and shock – IEC60068-2-6, -27

n

Maximum Operating Altitude: 30,000 ft.

STANDARDS COMPLIANCE

n

Electrical safety – UL508 / CSA C22.2/142; EN61010-1, CE

n

EMC – FCC part 15, ICES-003; EN61000-6-2/4, CE

n

Hazardous locations – ANSI/ISA 12.12.01 / CSA C22.2/213

(Class I, Div. 2); EN60079-15 (Zone 2, Category 3),
CE (ATEX)

n

Maritime – designed for marine and offshore per ABS

n

RoHS and WEEE compliant

PHYSICAL

n

DIN rail or direct panel mounting

n

Case – Aluminum (SLX) or Lexan (SL)

n

Ingress protection

p

SL models: IP30

p

SLX models: IP40

n

Weight – SLX: 0.23 kg (8 oz.); SL: 0.17 kg (6 oz.)

n

Dimensions – see mechanical diagram

SL/SLX-6RS-1/4/56 PORT INDUSTRIAL ETHERNET RING SWITCH

n

6 fast Ethernet ports with up to 2 ber

n

Managed, store & forward, wire-speed

n

All IEEE 802.3 Ethernet protocols supported

n

RJ45 ports (shielded) 10/100BaseTX

n

RJ45 port speed auto-negotiation

n

RJ45 MDI/MDIX auto-crossover

n

RJ45 TD and RD auto-polarity

n

Fiber optional on port 5 and 6

n

Fiber optic port speed: 100 Mbps

n

Fiber typical specs (see separate datasheet for details)

p

Multimode, 4 km, 1310 nm, 50-62.5/125 µm

p

Singlemode, 20 km, 1310 nm, 9-10/125 µm

p

Long haul, up to 120 km, 1550 nm, 9-10/125 µm

n

Typical latency (varies on load & settings)

p

@ 10 Mbps: 16 us + frame time

p

@ 100 Mbps: 5 us + frame time

n

Full or half duplex operation congurable per port

n

MAC addresses supported 2048

n

Memory bandwidth 3.2 Gbps

n

Ethernet isolation 1500 VRMS 1 minute

n

IEEE 802.3u (Fast Ethernet 100Mbps for newer devices)

n

IEEE 802.3 (10Mbps Ethernet supports legacy devices)

n

IEEE 802.1p (Priority Queuing – QoS, CoS, ToS/DS)

n

IEEE 802.3x (Full-Duplex with Flow Control)

n

Link loss recovery: 30 mS plus 5 mS per hop

n

Switches in a ring: <50 for best performance

n

Multiple rings supported (congurable)

n

Indicates power & operational status

n

Voltage same as switch input voltage

n

Maximum current output 0.5 Amp

n

Redundant input terminals

n

Reverse polarity protection

n

Input power (typ. with all ports active)

p

4 W (-1 model w/ no ber)

p

6 W (-4/5 model w/ 2 ber)

n

Power input voltage 10-30 VDC

n

Transient protection 15,000 watts peak

n

Spike protection 5,000 watts (10x for 10 uS)

All specications are subject to change.

ORDERING GUIDE

SLX-6RS-1-D1 6 RJ45 ports, metal case, wide temp.

SLX-6RS-4SC-D1 4 RJ45 ports, 2 multimode SC, 4 km

SLX-6RS-4ST-D1 4 RJ45 ports, 2 multimode ST, 4 km

SLX-6RS-5SC-D1 4 RJ45 ports, 2 singlemode SC, 20 km

SLX-6RS-5ST-D1 4 RJ45 ports, 2 singlemode ST, 20 km

SLX-6RS-5SCL-D1 4 RJ45 ports, 2 singlemode SC, 40+ km

SLX-6RS-5STL-D1 4 RJ45 ports, 2 singlemode ST, 40+ km

SL- w/ Lexan case and limited temperature

Setup Wizard Free - Windows conguration tool

ET-PS-024-02 Power supply – AC to 24VDC, 2A

SP-ETH-2 Dual port Ethernet surge & lightning

protector for 10/100 ports

NOTE: The sufx 1 means it is pre-congured for 1 ring on ports 5 & 6.
Contact SIXNET for other pre-conguration options.

ENVIRONMENTAL

n

Operating temperature:

p

SLX: -40 to +85 °C (cold startup at -40 °C)

p

SL: -40 to +60 °C

n

Storage temperature -40 to +85 °C

n

Humidity (non-condensing) 5 to 95% RH (optional
conformal coating is available)

n

Vibration and shock – IEC60068-2-6, -27

n

Maximum Operating Altitude: 30,000 ft.

STANDARDS COMPLIANCE

n

Electrical safety – UL508 / CSA C22.2/142; EN61010-1, CE

n

EMC – FCC part 15, ICES-003; EN61000-6-2/4, CE

n

Hazardous locations – ANSI/ISA 12.12.01 / CSA C22.2/213

(Class I, Div. 2); EN60079-15 (Zone 2, Category 3),
CE (ATEX)

n

Maritime – designed for marine and offshore per ABS

n

RoHS and WEEE compliant

PHYSICAL

n

DIN rail or direct panel mounting

n

Case – Aluminum (SLX) or Lexan (SL)

n

Ingress protection

p

SL models: IP30

p

SLX models: IP40

n

Weight – SLX: 0.23 kg (8 oz.); SL: 0.17 kg (6 oz.)

n

Dimensions – see mechanical diagram

MECHANICAL DRAWING

SL/SLX-6RS-1/4/56 PORT INDUSTRIAL ETHERNET RING SWITCH

All specications are subject to change.

ETHERNET PERFORMANCE

n

6 fast Ethernet ports with up to 2 ber

n

Managed, store & forward, wire-speed

n

All IEEE 802.3 Ethernet protocols supported

n

RJ45 ports (shielded) 10/100BaseTX

n

RJ45 port speed auto-negotiation

n

RJ45 MDI/MDIX auto-crossover

n

RJ45 TD and RD auto-polarity

n

Fiber optional on port 5 and 6

n

Fiber optic port speed: 100 Mbps

n

Fiber typical specs (see separate datasheet for details)

p

Multimode, 4 km, 1310 nm, 50-62.5/125 µm

p

Singlemode, 20 km, 1310 nm, 9-10/125 µm

p

Long haul, up to 120 km, 1550 nm, 9-10/125 µm

n

Typical latency (varies on load & settings)

p

@ 10 Mbps: 16 us + frame time

ETHERNET COMPLIANCE

REAL-TIME-RING™

“OK” ALARM OUTPUT

POWER INPUT

p

@ 100 Mbps: 5 us + frame time

n

Full or half duplex operation congurable per port

n

MAC addresses supported 2048

n

Memory bandwidth 3.2 Gbps

n

Ethernet isolation 1500 VRMS 1 minute

n

IEEE 802.3u (Fast Ethernet 100Mbps for newer devices)

n

IEEE 802.3 (10Mbps Ethernet supports legacy devices)

n

IEEE 802.1p (Priority Queuing – QoS, CoS, ToS/DS)

n

IEEE 802.3x (Full-Duplex with Flow Control)

n

Link loss recovery: 30 mS plus 5 mS per hop

n

Switches in a ring: <50 for best performance

n

Multiple rings supported (congurable)

n

Indicates power & operational status

n

Voltage same as switch input voltage

n

Maximum current output 0.5 Amp

n

Redundant input terminals

n

Reverse polarity protection

n

Input power (typ. with all ports active)

p

4 W (-1 model w/ no ber)

p

6 W (-4/5 model w/ 2 ber)

n

Power input voltage 10-30 VDC

n

Transient protection 15,000 watts peak

n

Spike protection 5,000 watts (10x for 10 uS)

n

Operating temperature:

p

SLX: -40 to +85 °C (cold startup at -40 °C)

p

SL: -40 to +60 °C

n

Storage temperature -40 to +85 °C

n

Humidity (non-condensing) 5 to 95% RH (optional
conformal coating is available)

n

Vibration and shock – IEC60068-2-6, -27

n

Maximum Operating Altitude: 30,000 ft.

n

Electrical safety – UL508 / CSA C22.2/142; EN61010-1, CE

n

EMC – FCC part 15, ICES-003; EN61000-6-2/4, CE

n

Hazardous locations – ANSI/ISA 12.12.01 / CSA C22.2/213

(Class I, Div. 2); EN60079-15 (Zone 2, Category 3),
CE (ATEX)

n

Maritime – designed for marine and offshore per ABS

n

RoHS and WEEE compliant

n

DIN rail or direct panel mounting

n

Case – Aluminum (SLX) or Lexan (SL)

n

Ingress protection

p

SL models: IP30

p

SLX models: IP40

n

Weight – SLX: 0.23 kg (8 oz.); SL: 0.17 kg (6 oz.)

n

Dimensions – see mechanical diagram

ORDERING GUIDE

SLX-6RS-1-D1 6 RJ45 ports, metal case, wide temp.

SLX-6RS-4SC-D1 4 RJ45 ports, 2 multimode SC, 4 km

SLX-6RS-4ST-D1 4 RJ45 ports, 2 multimode ST, 4 km

SLX-6RS-5SC-D1 4 RJ45 ports, 2 singlemode SC, 20 km

SLX-6RS-5ST-D1 4 RJ45 ports, 2 singlemode ST, 20 km

SLX-6RS-5SCL-D1 4 RJ45 ports, 2 singlemode SC, 40+ km

SLX-6RS-5STL-D1 4 RJ45 ports, 2 singlemode ST, 40+ km

SL- w/ Lexan case and limited temperature

Setup Wizard Free - Windows conguration tool

ET-PS-024-02 Power supply – AC to 24VDC, 2A

SP-ETH-2 Dual port Ethernet surge & lightning

NOTE: The sufx 1 means it is pre-congured for 1 ring on ports 5 & 6.

Contact SIXNET for other pre-conguration options.

protector for 10/100 ports

Consult factory for latest info.