RED DSMC FAN 2.0 Upgrade Instructions

DSMC FAN 2.0

UPGRADE INSTRUCTIONS

DSMCFAN 2.0 UPGRADEKIT

RED.COM

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

TABLE OF CONTENTS

Table of Contents 2

Disclaimer 3
Copyright Notice 3
Trademark Disclaimer 3
Compliance Statements 3
Safety Instructions 5

CHAPTER 1: Fan Upgrade Overview 7

Introduction 7
DSMC Fan 2.0 Upgrade Kit Components 7
Additional Resources 8

CHAPTER 2: Upgrade Bottom Fan 9

Required Tools 9
Remove Current Bottom Fan 9
Install 2.0 Bottom Fan 11

CHAPTER 3: Install Top Fan 15

Top Fan Compatibility 15
Install Top Fan with Top Vent Scoop 16
Install Top Fan with DSMC Tactical Top Plate 21

CHAPTER 4: Configure Firmware 27

Upgrade Firmware 27
Perform Hardware Rediscover 27
Adjust Fan Settings 28

C O PYR I G H T © 20 1 9 RE D . C O M , LLC 955-001 2 , REV-N |  2

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

DISCLAIMER

RED® has made every effort to provide clear and accurate
information in this document, which is provided solely for the user’s
information. While thought to be accurate, the information in this
document is provided strictly “as is” and RED will not be held
responsible for issues arising from typographical errors or user’s
interpretation of the language used herein that is different from that
intended by RED. All safety and general information is subject to
change as a result of changes in local, federal or other applicable
laws.

RED reserves the right to revise this document and make changes
from time to time in the content hereof without obligation to notify any
person of such revisions or changes. In no event shall RED, its
employees or authorized agents be liable to you for any damages or
losses, direct or indirect, arising from the use of any technical or
operational information contained in this document.

This document was generated on 1/10/2019. To see earlier versions
of this document, submit a Support ticket at https://support.red.com.

For comments or questions about content in this document, send a
detailed email to [e-mail].

COPYRIGHT NOTICE

COPYRIGHT© 2019 RED.COM, LLC
All trademarks, trade names, logos, icons, images, written material,

code, and product names used in association with the accompanying
product are the copyrights, trademarks, or other intellectual property
owned and controlled exclusively by RED.COM, LLC. For a
comprehensive list, see www.red.com/trademarks.

TRADEMARK DISCLAIMER

All other company, brand and product names are trademarks or
registered trademarks of their respective holders. RED has no
affiliation to, is not associated or sponsored with, and has no express
rights in third-party trademarks. Distagon is a registered trademark of
Carl Zeiss AG. Leica is a regestered trademark of Leica Microsystems
IR GmbH. Nikkor, is a registered trademark of Nikon Corporation.

FEDERAL COMMUNICATIONS COMMISSION (FCC)
STATEMENTS

This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This

equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for

help.

In order to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and
modifications made to the equipment without the approval of
manufacturer could void the users authority to operate this equipment.

NOTE: This device complies with Part 15 of the FCC Rules.
Operations subjected to the following two conditions (1) this device

may not cause harmful interference, and (2) this device must accept
any interference received, including that may cause undesirable
interference.

COMPLIANCE STATEMENTS

INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS

This device complies with Industry Canada license- exempt RSS
standards RSS 139 and RSS 210. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may
cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.
Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du
Canada.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 9 5 5 - 0 0 12, RE V - N | 3

The device shall be used in such a manner that the potential for
human contact is minimized

This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 cm between the radiator
and your body.

CAUTION: Exposure to Radio Frequency
Radiation.

CAUTION: Regulations of the FCC and FAA
prohibit airborne operation of radio- frequency
wireless devices because there signals could
interfere with critical aircraft instruments.

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

INFORMATION

CAUTION: If the device is changed or modified

without permission from RED, the user may void
his or her authority to operate the equipment.

AUSTRALIA AND NEW ZEALAND ST ATEMENTS

RED declares that the radio equipment described in this document
comply with the following international standards.

IEC 60065 - Product Safety
ETSI EN 300 328 - Technical requirement for radio equipment

Products with the CE marking comply with the EMC Directive
(2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by
the Commission of the European Community. Compliance with these
directives implies conformity to the following European Product Family
Standards.

EN 55022 (CISPR 22) – Electromagnetic Interference
EN 55024-1 (CISPR 24) – Electromagnetic Immunity
EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics
EN 61000-3-3 (IEC610000) – Power Line Flicker
EN 60065 (IEC60065) – Product Safety

RED declares digital devices described in this document comply with
the following Australian and New Zealand standards.

AS/NZS CISPR 22 – Electromagnetic Interference
AS/NZS 61000.3.2 – Power Line Harmonics
AS/NZS 61000.3.3 – Power Line Flicker

JAPAN STATEMENTS

This is a Class B product based on the
standard of the Voluntary Control Council
for Interference (VCCI) for information
technology equipment. If this equipment is
used near a radio or television receiver in a
domestic environment, it may cause radio
interference. Install and use the equipment

according to the instruction manual.

EUROPEAN UNION COMPLIANCE STATEMENTS

RED declares that the
radio equipment
described in this
document comply with
the R&TTE Directive
(1999/5/EC) issued by
the Commission of the

European Community.
Compliance with this directive implies conformity to the following

European Norms (in brackets are the equivalent international
standards).

EN 60065 (IEC 60065) – Product Safety
ETSI EN 300 328 Technical requirement for radio equipment
ETSI EN 301 489 General EMC requirements for radio

equipment.

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)

The Waste Electrical and Electronic
Equipment (WEEE) mark applies only to
countries within the European Union (EU)
and Norway. This symbol on the product and
accompanying documents means that used
electrical and electronic products should not
be mixed with general household waste. For
proper treatment, recovery and recycling,
please take this product to designated
collection points where it will be accepted
free of charge. Alternatively, in some

countries you may be able to return your
products to your local retailer upon purchase of an equivalent new
product.

Disposing of this product correctly will help save valuable resources
and prevent any potential negative effects on human health and the
environment, which could otherwise arise from inappropriate waste
handling. Contact your local authority for further details of your
nearest designated collection point. Penalties may be applicable for
incorrect disposal of this waste, in accordance with you national
legislation.

For business users in the European Union, if you wish to discard
electrical and electronic equipment, contact your dealer or supplier
for further information.

USAGE RESTRICTIONS FOR PRODUCTS THAT INCORPORATE
R.C.P.

Products that fall into this category are denoted
by inclusion of the Class 2 identifier symbol
(exclamation mark in a circle) accompanying
the CE Mark on the products regulatory label,
example to the left.



C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 9 5 5 - 0 0 12, RE V - N | 4

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

FRANCE

Usage Restrictions - Geographic Area Where Restriction Applies :
France

For mainland France

2.400 - 2.4835 GHz (Channels 1-16) authorized for indoor use

2.400 - 2.454 GHz (Channels 1-10) authorized for outdoor use

Restrictions d’utilisation - Zone géographique où les restrictions
s’appliquent : France

Pour la France métropolitaine

2.400 - 2.4835 GHz (Canaux 1 à 16) autorisé en usage intérieur

2.400 - 2.454 GHz (Canaux 1 à 10) autorisé en usage extérieur

NORWAY

This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund

Dette gjelder ikke for det geografiske området innenfor en radius av
20 km fra sentrum av Ny-Ålesund

RESPONSIBLE PARTY

RED Digital Cinema
34 Parker
Irvine, CA 92618
USA

SAFETY INSTRUCTIONS

DO NOT use the camera or accessories near water. Avoid
exposing your camera to moisture. The unit is not waterproof, so
contact with water could cause permanent damage to the unit as
well as electric shock and serious injury to the user. DO NOT use
the camera in the rain or under other conditions with high
moisture without appropriate protection, and immediately remove
power source if camera or accessories are exposed to moisture.

WARNING: To reduce the risk of fire or electric
shock, do not expose the camera to rain or
moisture.

DO NOT expose the camera to laser beams, as laser beams may
damage the sensor.

DO NOT expose your camera to excessive vibration or impact
(shock). Be careful not to drop your camera. Internal mechanisms
may be damaged by severe shock. Mechanical alignment of
optical elements may be affected by excessive vibration.

ELECTROMAGNETIC INTERFERENCE: The use of devices using
radio or other communication waves may result in the malfunction
or interference with the unit and/or with audio and video signals.

Clean only using a dry cloth. When cleaning your camera,
remember that it is not waterproof and moisture can damage
electronic circuitry. DO NOT rinse or immerse any element of the
camera, lens or other accessory, keep them dry at all times. DO
NOT use soaps, detergents, ammonia, alkaline cleaners, and
abrasive cleaning compounds or solvents. These substances may
damage lens coatings and electronic circuitry.

Maintain sufficient ventilation—DO NOT block any ventilation
openings or obstruct cooling fan airflow.

CAUTION: Proper camera ventilation requires a
minimum 0.5" (1.25 cm) clearance between the
camera ventilation openings and external
surfaces. Verify that objects that can block the fan
intake and exhaust ports do not impede airflow.
Failure to permit adequate airflow may result in
overheating of the camera, degraded operation
and in extreme situations, damage to the camera.

DO NOT operate or store near any heat sources such as
radiators, heat registers, stoves, or any other apparatus that
produce heat. Store in a protected, level and ventilated place.
Avoid exposure to temperature extremes, damp, severe vibration,
strong magnetic fields, direct sunlight or local heat sources during
storage. Remove any batteries from the camera before storage.
Recommended storage and usage temperatures for your camera,
lenses and other accessories are:

Operating range: 0°C to 40°C (32°F to 104°F)
Storage range: –20°C to 50°C (–4°F to 122°F)

If there are any performance issues with your camera or
accessories when operating within this temperature range, submit
a Support ticket at https://support.red.com.

The DSMC® Side Handle, side SSD modules, rear modules, and
lens mounts are NOT HOT SWAPPABLE, meaning you cannot
remove or install them while the camera is turned on. Before
installing or removing any of these accessories, you MUST turn off
the camera. Failure to do so may result in damage to the
accessory and/or camera BRAIN® that will not be covered under
warranty.

DO NOT bypass the third prong of the grounding-type plug on the
power cord of the DSMC AC Power Adaptor. A grounding-type
plug has two blades and a third “grounding” prong. The third
prong is provided for your safety. A grounding-type plug shall be
connected to an outlet with a protective earthen connection. If the
grounding-type plug does not fit into your outlet, do not attempt to
modify the plug or outlet, consult a qualified electrician.

Protect all power cords from being pinched, walked on or driven
over by a vehicle. Replace any power cords suspected of
sustaining damage due to crushing or other forms physical
damage.

Products marked with this symbol are class 2
devices. These devices are not provided with a
grounding type plug.

CAUTION: The power cord plug for the DSMC
AC Power Adaptor is used as the power
disconnect. To disconnect all power from the
DSMC AC Power Adaptor, unplug the power cord
plug from the wall outlet. During use, the power
cord plug should remain easily accessible at all
times.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 9 5 5 - 0 0 12, RE V - N | 5

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

Lithium-ion batteries may be subject to special handling
requirements pursuant to federal and local laws. Refer to specific
shipping instructions included with your battery regarding proper
transport of your battery. Do not handle your battery if it is
damaged or leaking. Disposal of batteries must be in accordance
with local environmental regulations. For example, California law
requires that all rechargeable batteries must be recycled by an
authorized recycle center. Storing batteries fully charged or in
high temperature conditions may permanently reduce the life of
the battery. Available battery capacity may also be temporarily
lessened after storage in low temperature conditions.

WARNING: DO NOT expose the battery to
excessive heat.

WARNING: Danger of explosion if an incorrect
battery is charged with the RED Charger or is
used to power the camera and accessories.
Replace only with the same or equivalent type
battery.

CAUTION: Refer all service and repair to
qualified RED service personnel. To reduce the
risk of electric shock, and damage to the
camera or accessories, DO NOT attempt to
perform any servicing other than any procedures
that are recommended in the operating
instructions.

INDOOR USE ONLY: Products marked with this
symbol are designed for use indoors only.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 9 5 5 - 0 0 12, RE V - N | 6

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

CHAPTER 1:

FAN UPGRADE OVERVIEW

INTRODUCTION

The DSMC® Fan 2.0 Upgrade is available for SCARLET® and REDEPIC® cameras. You may upgrade your BRAIN®
with one (1) or both of the following fans:

DSMC Fan 2.0 (Bottom): Replaces the bottom fan with a more powerful, efficient, and quieter fan that allows you
to run at a low noise level for a longer period of time. The bottom fan is specific to your corresponding camera
model and is distinguished by a SCARLET or EPIC coin and grill.

DSMC Fan 2.0 (Top): Replaces the top fan with a more powerful, efficient, and quieter fan. Provides you with a
quiet, effective cooling solution that allows for extended recording sessions at a low noise level.

RED Digital Cinema® can perform this installation for you, free of charge. Submit a Support ticket at

https://support.red.com.

WARNING: These instructions are provided for use AT YOUR OWN RISK. Failure to comply in full with these
instructions may cause severe damage to your camera and WILL NOT be covered by any RED® warranty plan.
Damage to the BRAIN or other components of the DSMC system caused by improper installation is not covered under
warranty.

WARNING: The top of the BRAIN and top fan may be hot. To prevent accidental contact, RED recommends that you
always operate your BRAIN with a compatible top vent scoop or DSMC Tactical Top Plate 2.0.

NOTE: For EPIC and SCARLET cameras, the DSMC Fan 2.0 (Bottom) and the DSMC Magnesium PL Mount 2.0 are
not natively compatible with each other, since the fan grill prevents the lens mount locking ring from rotating. To use
these devices together, remove the lower tabs from the locking ring using a T8 TORX® driver.

NOTE: Once the upgrade is complete, a firmware update and/or hardware rediscover is required to recognize new
fans. For more information, go to "Configure Firmware" on page27.

NOTE: RED recommends upgrading your camera firmware to v4.0.12 or later to support full control over both top and
bottom fans. The DSMC Fan 2.0 Upgrade is not fully supported by earlier versions of camera firmware.

DSMC FAN 2.0 UPGRADE KIT COMPONENTS

DSMC FAN 2.0 UPGRADE KIT (TOP)

This kit includes the following components:

2.0 Top Fan Assembly
EPIC-X (black) or SCARLET-X® (gray) top vent scoop
T6 TORX driver (short)
T8 TORX driver
Two (2) M2x0.4 x 4 mm cap screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N | 7

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

DSMC FAN 2.0 UPGRADE KIT (BOTTOM)

This kit includes the following components:

2.0 bottom fan assembly
Fan grill
T10 TORX driver
Two (2) M3x0.5 x 6 mm cap screws
One (1) ESD-safe solder stick

DSMC FAN 2.0 UPGRADE KIT (TOP/BOTTOM)

This kit includes the following components:

2.0 Top Fan Assembly
EPIC-X (black) or SCARLET-X (gray) top vent scoop
T6 TORX driver (short)
T8 TORX driver
Two (2) M2x0.4 x 4 mm cap screws (top)

2.0 bottom fan assembly
Fan grill
T10 TORX driver
Two (2) M3x0.5 x 6 mm cap screws (bottom)
One (1) ESD-safe solder stick

NOTE: For EPIC and SCARLET cameras, the DSMC Fan 2.0 (Bottom) and the DSMC Magnesium PL Mount 2.0 are
not natively compatible with each other, since the fan grill prevents the lens mount locking ring from rotating. To use
these devices together, remove the lower tabs from the locking ring using a T8 TORX driver.

ADDITIONAL RESOURCES

The following resources offer additional information about RED, the DSMC system, and the RED community:

RED.com: Check the official RED website for the latest information about RED products.
RED Learn Articles: RED offers in-depth technical articles about RED cameras, post-production, and digital

cinematography.
RED Downloads: Go to RED Downloads to download the latest firmware, operation guides, and post-production

software.
DSMC Toolkit: Go to RED Downloads to find the DSMC Toolkit, which offers many helpful tools and resources to

customize and improve your camera workflow.

RED Support: Check the RED SUPPORT site for FAQs, or to file a support ticket.
In-Camera Help: Select the Help button on an in-camera screen to open up the help for that screen.
REDUSER: Discuss all things RED on the REDUSER third-party forum.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 9 5 5 - 0 0 12, RE V - N | 8

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

CHAPTER 2:

UPGRADE BOTTOM FAN

REQUIRED TOOLS

T10 TORX® driver
ESD-safe solder stick (included)

REMOVE CURRENT BOTTOM FAN

1. Turn off the camera.
2. Remove all power sources, accessories, the lens, and the lens mount.
3. Cover the camera opening with a DSMC® Front Body Cap to protect your sensor from dust and foreign particles

during the fan upgrade procedure.
4. Place the BRAIN® on a suitable flat work surface with the front of the BRAIN facing upward.
5. Use a T10 TORX driver to remove the two (2) M3x0.5 x 6 mm cap screws that attach the current fan grill to the

BRAIN.

Figure: Remove Cap Screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N | 9

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

6. Remove the fan grill by rotating it upward, using the ESD-safe solder stick (included) for assistance if necessary.

Figure: Remove Grill

7. Pinch the upper right and lower left corners of the current fan assembly.

Figure: Pinch Fan Corners

NOTE: In the next step, DO NOT pull out the connector, or damage will occur.

8. While continuing to hold the upper right and lower left corners of the current fan assembly, wiggle and pull the fan

assembly back-and-forth until it releases from the BRAIN.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  10

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

9. If the connector on your original fan assembly has a white tab, depress the white tab with the ESD-safe solder

stick and gently pull the cables until the connector is free.
If the connector does not have a white tab, gently pull the cables until the connector is free. Use the ESD-safe

solder stick for assistance if necessary.

Figure: Disconnect Fan

INSTALL 2.0 BOTTOM FAN

NOTE: If any of the fan bumpers fall off of the fan assembly during the installation process, reattach the bumpers and

ensure that they are properly aligned.
1. Identify the new fan assembly.
2. Align the female connectors with the pins in the connector slot and verify the following:

Verify that the blue wire is at the top, and the red wire is at the bottom.
Verify that the connector enters the slot directly, and NOT on its side, so that the female connectors align with

the pins in the connector slot.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  11

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

3. Carefully push the white connector into the appropriate slot on the BRAIN, using the ESD-safe solder stick for

assistance if necessary.
You will hear a click when the connector is successfully attached to the BRAIN.

Figure: Connect Fan

4. Insert the new fan assembly so that the fan bumpers are facing away from the camera, and that the label on the fan

is facing inward toward the camera. Keep the front of the fan assembly tilted forward, and make sure that the
connector cables are under the surface.

NOTE: DO NOT push the fan assembly into the seat all the way. Installing the fan grill secures the fan assembly.

Figure: Insert Fan

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  12

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

5. Install the fan grill by pointing the top of the fan grill downward and sliding both tabs into the slots below the

DSMC Front Body Cap, so that the grill lies flat on top of the fan assembly.

Figure: Install Fan Grill

6. Use a T10 TORX driver to install the two (2) M3x0.5 x 6 mm cap screws (included) that attach the fan grill to the

BRAIN. DO NOT FULLY TIGHTEN.

Figure: Install Cap Screws

7. Tighten the M3x0.5 x 6 mm screws evenly. DO NOT exceed 70 in-oz, or damage may occur.

WARNING: DO NOT OVERTIGHTEN.

8. Reattach the lens mount, lens, and any DSMC accessories that you removed from the BRAIN.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  13

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

9. Upgrade your firmware or perform a hardware rediscover to ensure that your camera recognizes the new fan. For

more information, go to "Configure Firmware" on page27.
NOTE: If you need to replace any screws, submit a Support ticket at https://support.red.com.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  14

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

CHAPTER 3:

INSTALL TOP FAN

TOP FAN COMPATIBILITY

The table below describes which top plates are compatible with the top fan. All compatible top plates provide
sufficient clearance for the top fan.

Once again making obsolescence obsolete, RED® provides a replacement top vent scoop in each DSMC® Fan 2.0
Upgrade Kit (Top and Bottom/Top), so that you can install a compatible top plate along with your top fan.

TOPPLATE PART NUMBER COMPATIBLE NOTES

EPIC-X top vent
scoop

SCARLET-X®
top vent scoop

2.0

DSMC®
Tactical Top
Plate 2.0

EPIC-M top
vent scoop

SCARLET-X top
vent scoop

DSMC Tactical
Top Plate

1

125-2057 Yes This top plate currently ships with EPIC-X cameras, and

is included in the DSMC Fan 2.0 Upgrade Kit (Top and
Bottom/Top) — EPIC® as a replacement for
incompatible top plates.

125-2057-02 Yes This top plate is included in the DSMC Fan 2.0

Upgrade Kit (Top and Bottom/Top) — SCARLET® as a
replacement for incompatible top plates.

790-0383 Yes This second generation DSMC Tactical Top Plate is

specially designed to provide extra efficiencies and
clearance for the DSMC Top Fan.

125-2095 No If you have an EPIC-M top vent scoop, install the

replacement EPIC-X top vent scoop included in the
DSMC Fan 2.0 Upgrade Kit (Top and Bottom/Top) —
EPIC when installing the top fan.

125-2100 No If you have a SCARLET-X top vent scoop, install the

replacement SCARLET-X top vent scoop 2.0 included
in the DSMC Fan 2.0 Upgrade Kit (Top and
Bottom/Top) — SCARLET when installing the top fan.

790-0255 No If you currently have an original DSMC Tactical Top

Plate, you can either send in your DSMC Tactical Top
Plate and receive credit toward the purchase of a new
DSMC Tactical Top Plate 2.0, or you can send in your
DSMC Tactical Top Plate for modification by RED free
of charge.

1. Submit a request at https://support.red.com/home if you have an eligible EPIC-M that has not already been sent in for the free upgrade

program. The upgrade program includes mechanical improvements and additional mounting points. The upgrade should be performed before
you install the top fan.

The part number of each top vent scoop is marked on the bottom of the top vent scoop.

NOTE: Any top vent scoop part number that is not listed in the table above is not compatible with the top fan.
NOTE: For more details about the DSMC Tactical Top Plate modification and trade-in options, submit a request at

https://support.red.com/home.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N | 15

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

INSTALL TOP FAN WITH TOP VENT SCOOP

REQUIRED TOOLS

T8 TORX® driver
T6 TORX driver (included)

REMOVE TOP VENT SCOOP

1. Turn off the camera.
2. Remove all power supplies, accessories, and the lens.
3. Place the BRAIN® on a suitable flat work surface with the top of the BRAIN facing upward.
4. Use a T8 TORX driver to remove the four (4) M2.5x0.45 x 6 mm cap screws that attach the top vent scoop to the

BRAIN.

Figure: Remove Cap Screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  16

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

5. Remove the top vent scoop from the BRAIN.

Figure: Remove Top

6. Use a T6 TORX driver (included) to remove the two (2) M2x0.4 x 4 mm cap screws from the exhaust fan pogo

cover (black plastic slip).

Figure: Remove Cap Screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  17

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

7. Remove the exhaust fan pogo cover.

NOTE: Store the exhaust fan pogo cover and the two (2) M2x0.4 x 4 mm cap screws in a safe place, in case you
want to remove or replace the top fans at a later time.

Figure: Remove Cover

INSTALL TOP FAN AND TOP VENT SCOOP

1. Place the top fan assembly on top of the vent so that the “RED PRO” lettering is facing up and the connector is

facing down.

Figure: Align Top Fan

2. Attach the top fan to the BRAIN by installing two (2) M2x0.4 x 4 mm cap screws (included) with a T6 TORX driver

(included).

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  18

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

3. Tighten the M2x0.4 x 4 mm cap screws evenly. DO NOT exceed 30 in-oz, or damage may occur.

WARNING: DO NOT OVERTIGHTEN.

Figure: Install Top Fan

4. Place the top vent scoop on top of the fan.

Figure: Place Top on Fan

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  19

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

5. Attach the top vent scoop to the BRAIN by installing four (4) M3x0.5 x 6 mm cap screws with a T8 TORX driver.

DO NOT FULLY TIGHTEN.
WARNING: DO NOT OVERTIGHTEN.

Figure: Install Cap Screws

6. Tighten the M3x0.5 x 6 mm cap screws evenly. DO NOT exceed 30 in-oz, or damage may occur.

WARNING: DO NOT OVERTIGHTEN.
7. Reattach any DSMC accessories that you may have removed from the BRAIN.
8. Upgrade your firmware or perform a hardware rediscover to ensure that your camera recognizes the new fan. For

more information, go to "Configure Firmware" on page27.

NOTE: The top fan may not run immediately after turning on the BRAIN, as the top fan runs when the BRAIN

requires additional cooling power.

NOTE: If you need to replace any screws, submit a Support ticket at https://support.red.com.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  20

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

INSTALL TOP FAN WITH DSMC TACTICAL TOP PLATE

REQUIRED TOOLS

T6 TORX driver (included)
3/16" hex key
3 mm hex key

REMOVE DSMC TACTICAL TOP PLATE

1. Turn off the camera.
2. Remove all power supplies, accessories, and the lens.
3. Place the BRAIN on a suitable flat work surface with the top of the BRAIN facing upward.

Figure: Loosen M4x0.7 x 12.5 mm Captive Screws

4. Use a 3/16" hex key to loosen the two (2) 1/4-20 x 12 mm screws.
5. Continue to loosen all screws until the plate can be removed.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  21

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

6. Remove the plate.

Figure: Remove Top Plate

7. Use a T6 TORX driver (included) to remove the two (2) M2x0.4 x 4 mm cap screws from the exhaust fan pogo

cover (black plastic slip).

Figure: Remove Cap Screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  22

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

8. Remove the exhaust fan pogo cover.

NOTE: Store the exhaust fan pogo cover and the two (2) M2x0.4 x 4 mm cap screws in a safe place, in case you

want to remove or replace the top fans at a later time.

Figure: Remove Cover

INSTALL TOP FAN AND DSMC TACTICAL TOP PLATE 2.0

NOTE: The top plate installation instructions below are also applicable to the original DSMC Tactical Top Plate that

was modified by RED to accommodate the top fan.

1. Ensure that the original Tactical Top Plate and exhaust fan pogo cover are already removed from the BRAIN.

For more information on removing the Tactical Top Plate and exhaust fan pogo cover, go to "Remove DSMC

Tactical Top Plate" on page21.

2. Place the BRAIN on a suitable flat work surface with the top of the BRAIN facing upward.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  23

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

3. Place the top fan assembly on top of the vent so that the “RED PRO” lettering is facing up and the connector is

facing down.

Figure: Insert Top Fan

4. Attach the top fan to the BRAIN by installing two (2) M2x0.4 x 4 mm cap screws (included) with a T6 TORX driver

(included). DO NOT FULLY TIGHTEN.

Figure: Install Top Fan

5. Tighten the M2x0.4 x 4 mm cap screws evenly. DO NOT exceed 30 in-oz, or damage may occur.

WARNING: DO NOT OVERTIGHTEN.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  24

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

6. Place the DSMC Tactical Top Plate 2.0 on top of the fan.

Figure: Place Plate on Fan

7. Align the captive screws in the plate with the threaded holes on top of the BRAIN.
8. Use a 3/16" hex key to tighten the two (2) 1/4-20 x 12 mm screws by about two (2) turns. DO NOT FULLY

TIGHTEN.

Figure: Install 1/4-20 x 12 mm Screws

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  25

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

9. Use a 3 mm hex key to tighten the four (4) M4x0.7 x 12 mm captive screws by about two (2) turns. DO NOT FULLY

TIGHTEN.

Figure: Install M4x0.7 x 12.5 mm Captive Screws

10. Fully tighten the 1/4-20 x 12 mm screws. DO NOT OVERTIGHTEN.
11. Tighten the M4x0.7 x 12.5 mm captive screws in a cross pattern. DO NOT OVERTIGHTEN.
12. Reattach any accessories that you removed from the BRAIN.
13. Upgrade your firmware or perform a hardware rediscover to ensure that your camera recognizes the new fan. For

more information, go to "Configure Firmware" on page27.

NOTE: The top fan may not run immediately after turning on the BRAIN, as the top fan runs only when the BRAIN

requires additional cooling power.

NOTE: If you need to replace any screws, submit a Support ticket at https://support.red.com.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  26

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

CHAPTER 4:

CONFIGURE FIRMWARE

RED® recommends that you upgrade your camera firmware to the latest firmware version in order to have full control
over both the top and bottom fans. Camera firmware v4.0.12 and later offers full hardware support for both fans, and
provides more robust and precise fan settings, so that you have full control over the speed and noise level of the fans.
Earlier versions of firmware do not fully support DSMC® 2.0 fans.

UPGRADE FIRMWARE

1. Download the latest firmware file for your camera from www.red.com/downloads.
2. Perform the firmware upgrade on your camera.

NOTE: For more information on upgrading firmware, see the camera operation guides , available at

www.red.com/downloads.

PERFORM HARDWARE REDISCOVER

If you upgraded your firmware before installing the new fans, or if you are not upgrading your firmware, perform a
manual hardware rediscover after you install new fans so that the camera firmware recognizes the new fans.

NOTE: The screenshots below are from firmware v6.0.
1. Turn on the camera.
2. Go to Menu > Settings > Maintenance.
3. Select Rediscover.
4. Select Yes to perform the hardware rediscover.

Wait for the camera to turn off.

Figure: Hardware Rediscover

5. Turn on the camera.

The camera firmware rediscovers all hardware and caches the data for future boot cycles.

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N | 27

DSMC FAN 2.0 UPGRADE INSTRUCTIONS

ADJUST FAN SETTINGS

After installing the 2.0 fans and performing other necessary operations, adjust your fan settings to account for the new
top fan (if applicable), the increased speed of the bottom fan, and the new fan mode settings that are available in
firmware v4.0.12 and later.

NOTE: The screenshots below are from firmware v6.0.
1. Turn on the camera.
2. Navigate to Menu > Settings > Setup > Fan Control.
3. Adjust the fan settings to meet your personal preferences or the needs of your project.

NOTE: For more information on upgrading firmware, see the camera operation guides , available at

www.red.com/downloads.

Figure: Adjust Fan Settings

C O PYR I G H T © 2 0 1 9 R ED. C OM, LLC 955-001 2 , REV-N |  28