RDL D-RC2, D-RC2M, D-RC3, D-RC3M, DS-RC3 Datasheet

Models DS-RC2 and D-RC2

Remote Audio Mixing Control

DS-RC2

D-RC2

Models DS-RC3 and D-RC3

Remote Audio Mixing Control

Models DS-RC2M and D-RC2M

Remote Audio Mixing Control with Muting

DS-RC2M

D-RC2M

Models DS-RC3M and D-RC3M

Remote Audio Mixing Control with Muting

DS-RC3

 Remote Audio Mixing Control Panel
 Single-Turn Rotary Controls
 Single Control Location
 Available in RDL White or Stainless Steel

APPLICATION: The D-RC type remote audio mixing controls provide user-accessible volume knobs for two or three sources. Each
control is available with level controls only, or with level controls plus a muting button for each channel. They function exactly as a
mixer without the need to send audio to and from the remote location. A rear-panel RJ45 jack provides the connection for standard
twisted-pair wiring between the remote control and an RDL remote-controlled mixer. The cable sends the knob position and muting
status data to the mixer. All audio signals remain local to the mixer which uses VCA technology to set the mixer levels. A long life
10 kΩ potentiometer is used in the control for setting the VCA voltage. Muting models provide a MUTE button for each mixer
channel that alternately mutes or un-mutes the audio. An LED MUTE indicator glows red when the signal is muted and turns green
when the audio channel is active. Each model is offered in a standard RDL white front panel or in stainless steel with custom
lettering available. These finishes match other RDL remote selectors and jack plates for a visually appealing installation of multiple
controls.

RDL  659 N. 6th St.  Prescott, AZ., USA 86301  [phone]  FAX [phone]  www.rdlnet.com

D-RC3

 Direct Control of RDL Mixers with an RJ45 Remote Control Port
 Standard Twisted-Pair Interconnection to Mixer
 Mute Button Toggles Output On and Off (Muting Models)
 Red/Green On/Off Mute Indicator (Muting Models)

DS-RC3M D-RC3M

ACCESSORIES
Models DS-RC2, D-RC2, DS-RC2M, D-RC2M
Models DS-RC3, D-RC3, DS-RC3M, D-RC3M

Remote Audio Mixing Controls

Installation/Operation

Declaration of Conformity available from rdlnet.com.

Sole EMC specifications provided on product package.

Specifications are subject to change without notice.

Note: If an RC2 two-channel control is connected to an RDL 3-input
mixer, the remote control will adjust mixer inputs 1 and 2. The level
for mixer input 3 will set at the mixer.

TYPICAL PERFORMANCE

Compatibility: RDL remote controlled mixers (light blue color-coded control jack)
Control connector: RJ45
Mute button (muting models): Momentary, one per channel
Indicator (muting models): Red = Muted; Green = Active
Mounting: Mounts in standard US electrical box; cover plate available separately

Dimensions: Height: 4.1 in. 10.4 cm; Depth: 1.44 in. 3.7 cm (without knob)
Depth: 2 in. 5 cm (with knob); Width: 1.7 in. 4.33 cm

Radio Design Labs Technical Support Centers

U.S.A. [phone], [phone]; Fax: [phone]

891-5400A

Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287

NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rule. These limits ar e designed to
provide reasonable protection against harmful interfer ence
in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications .
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or televis ion reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the
interference by one or more of the following measures:

 Reorient or relocate the receiving antenna
 Increase the separation between the equipment

and receiver

 Connect the equipment into an outlet on a circuit

different from that which the receiver is
connected.

 Consult the dealer or an experienced radio/TV

technician for help.