RDL D-RLC2, DS-RLC2, DB-RLC2 Datasheet

ACCESSORIES

Models D-RLC2, DS-RLC2, DB-RLC2

Remote Level control

i i

DB-RLC2

 Remote Level Control Panel
 Pushbutton UP and DOWN
 10-segment Visual Level Display

The D SERIES-RLC2 is part of the group of versatile wall-mounted products from Radio Design Labs. The standard mounting case can be directly fastened in North
American electrical boxes or in RDL International wall boxes.

DS-RLC2

D-RLC2

 Multiple Control/Indication Locations
 Premium quality Remote Panel
 Professional Aesthetic Appearance

APPLICATION: The D SERIES-RLC2 is the ideal choice where levels are to be controlled from a single, or from multiple

control locations; and visual level indication is desired.

The -RLC2 is designed to directly interface with an ST-RG1 Ramp Generator or RU-VCA2A and RU-VCA6A Digitally Controlled
Audio Attenuators. The -RLC2 has two momentary pushbuttons, UP and DOWN. Pushing each button sends the appropriate
signal back to the RDL control module. When connected to the RU-VCA2A or RU-VCA6A, pushing both buttons on the -RLC2
simultaneously causes the unit to return to a PRESET level.

The -RLC2 panel has a 10-segment LED display, which provides a visual indication of the level setting. The linearity of the display
is tailored to produce indications consistent with the audible level. The appearance of the -RLC2 matches other RDL accessories
such as the -RCS4 remote source selector (used with RDL’s RU-SX4A four input audio selector). The -RLC2 and -RCS4 may be
mounted together in a double wall box to form visually appealing control of both audio source and audio level.

In systems where several control/level indication locations are needed, multiple -RLC2’s may be connected to a single RDL control
module. Wires may be run from the control unit to an -RLC2, then daisy chained on to more -RLC2s. Five conductors are required
for connection to the -RLC2.

The -RLC2 is constructed on a steel frame. The electronics are fully protected within the rear enclosure. Connections are made
through a rear panel detachable terminal block. Pushbuttons are long-life switches mounted to provide protection from excessive
frontal force.

All the -RLC2 features combine to make it the ideal choice for remote-level control in high quality systems. Use the -RLC2
individually with an RDL control module, or combine it side-by-side with other RDL remote accessories as part of a complete
audio/video system.

RDL  659 N. 6th St.  Prescott, AZ., USA 86301  [phone]  FAX [phone]  www.rdlnet.com

ACCESSORIES

Models D-RLC2, DS-RLC2, DB-RLC2

Remote Level Control

Mounting
The D SERIES–RLC2 should be mounted in an RDL WB-1U wall box or equivalent. The ambient operating environment must not exceed 40 degrees C.

Installation/Operation

EN55103-1 E1-E5; EN55103-2 E1-E4; EN60065

Typical Performance reflects product at publication tim e exclusive of EMC
data, if any, supplied with product. Specifications are subject to change
without notice. This product is Professional Apparatus.

TYPICAL PERFORMANCE
Ramp Input: 0 to 10 Vdc
Outputs: UP and DOWN, pushbutton actuated 15 Vdc @ 5 mA
Power Requirement: 24 Vdc @ 75 mA, Ground-referenced
Mounting: Mounts in standard US electrical box,
decorative plate available separately
Dimensions: Height: 4.11 in. (10.4 cm)
Depth: 1.66 in. (4.21 cm)
Width: 1.72 in. (4.37 cm)

891-5585

U.S.A. [phone], [phone]; Fax: [phone]

Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287

Radio Design Labs Technical Support Centers