RC Logger 89134RC Operating instructions
Operating instructions
RC Logger Datalink
No. 89134RC
INTRODUCTION
The datalink facilitates data transfer between the RC Logger EYEControl app and
RC Logger quadcopters (e.g. NovaX 350) when the mobile device running the app and the
quadcopter are out of range (this range is limited by Bluetooth
The datalink attaches to the R8 Radio System (89102RC) that sends and receives data
destined for the EYEControl app.
Various live data can be transmitted, including telemetry data and task points. You can,
for instance, determine new task points in the app and commit the new settings to the
quadcopter in ight.
The datalink has a built-in rechargeable battery.
Important note:
The NovaX 350 must run at least NovaX rmware version 2.0 (NovaX 2.0). For other
RC Logger quadcopters, refer to latest information on www.rclogger.com.
Detailed instructions on how you can update your quadcopter to the latest rmware
is available from www.rclogger.com.
®
).
» is visibly damaged,
» is no longer working properly,
» has been stored for extended periods in poor ambient conditions or
» has been subjected to any serious transport-related stresses.
> Please handle the product carefully. Jolts, impacts or a fall even from a low height can
damage the product.
Signal
> Large objects, walls, pillars, etc. may reduce the signal quality, which may result in
signal loss or transmission failure.
> High voltage power lines or communication broadcasting towers may inuence the
quality of the signal and lead to signal loss. Keep sufcient distance.
Before commissioning
> Before every ight, check the functional reliability of the product. Watch out for any
visible damage such as defective plug connections or product damage.
> Before you y, make sure the battery has sufcient capacity. Recharge if necessary.
> Test the product functionality before take-off.
During operation
Important note:
When you make use of the autonomous ying feature provided by the app, ensure
that you are able to intercept immediately with the transmitter in case of unintended
behaviour.
INTENDED USE
Please download the latest version of the operating
instructions from our website at www.rclogger.com. Navigate
to the product page and open the ”Downloads” tab. Click on
”Operating instructions” to start the download.
Make this product available to third parties only together
with its
operating
The product must not become damp or wet.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting, re,
electric shock etc. Read the instructions carefully and keep them. Make this product
available to third parties only together with its instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
instructions.
DELIVERY CONTENT
> Datalink
> Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially
observe the safety information. If you do not follow the
safety instructions and information on proper handling in
these instructions, we assume no liability for any resulting
personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
> Do not take any risks when operating the model. Your own safety and that of your
environment is solely down to you being responsible when dealing with the model.
> Use the product only if your ability to respond is unrestricted. The inuence of tiredness,
alcohol or medication can cause incorrect responses.
> Never remove the product from the transmitter when it is in use.
Batteries
> The battery is built-in. Do not try to remove it.
> Batteries must not be dismantled, short-circuited or thrown into re. There is a risk of
explosion!
> Caution: Risk of explosion if battery is replaced by an incorrect type.
> Dispose of used batteries according to the instructions.
INSTALLATION
1. Turn the transmitter off.
2. Plug the datalink into the trainer port at the back of the transmitter. Make sure it sits
rmly. See above images.
INDICATOR LIGHTS
General
> The product is not a toy. Keep it out of the reach of children and pets.
> Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
> Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
> Do not use the product in rain.
> Do not place the product under any mechanical stress.
> If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if the
product:
Status ‘Charge Status’ ‘Low Battery’ ‘Bluetooth’
Turned off Off Off Off
Pairing mode status-dependent Alternate Red / Blue ash
Connected status-dependent status-dependent Blue double ash
Not connected status-dependent status-dependent Blue single ash
Low Battery warning status-dependent Red double ash status-dependent
Charging Red status-dependent status-dependent
Fully Charged Green status-dependent status-dependent
TRANSMISSION DISTANCES
The transmission distance is limited by the technology used for each link. Study below
diagram and observe the distances when operating the datalink.
10 m 1000 m
CHARGING THE BATTERY
Battery life: 3 hours
Charging duration: 1 hour
You may charge the battery while using the datalink.
1. Connect a regular micro USB cable to the micro USB port located on the right side of
the datalink.
2. Connect the USB-A connector to a USB power source (5 V/DC, 40 mA).
3. The indicator light Charge Status lights up red.
4. When the battery is fully charged the indicator light Charge Status lights up green.
5. Remove the USB cable.
OPERATION
Auto-off:
If the datalink is not connected to the mobile device within 5 minutes, it turns off
automatically.
Power on
When the datalink is turned off, press and hold the front button for approx. 3 seconds to
turn it on. The Bluetooth indicator light emits single blue ashes.
Power off
When the datalink is turned on, press and hold the front button for approx. 3 seconds to
turn it off. The datalink turns off automatically when not connected for at least 5 minutes.
Pairing
1. Make sure you have the latest version of the EYEControl app installed on your mobile
device and run the RC Logger rmware version FW2.0 or higher on your quadcopter.
2. When the datalink is turned off, press and hold the front button for approx. 6 seconds.
The Low Battery and Bluetooth indicator lights ash alternatively, indicating pairing
mode.
3. Enable Bluetooth on your mobile device and pair the datalink with the mobile device
through the app interface.
4. After approx. 30 seconds, the paired datalink and mobile device is indicated by blue
double ashes of the Bluetooth indicator light. In case of failed pairing, the Bluetooth
indicator light emits blue single ashes. Restart pairing procedure.
CLEANING AND CARE
> The datalink does not require any maintenance, do not disassemble it. Maintenance or
repairs may be carried out by a professional only.
> Do not let liquid enter the datalink.
> Clean the exterior of the datalink using a clean, soft, dry cloth only.
> Do not use any aggressive cleaning agents or chemical solutions as these may
damage the housing causing discoloration and/or malfunction.
DISPOSAL
In order to preserve, protect and improve the quality of environment, protect
human health and utilise natural resources prudently and rationally, the user
should return unserviceable product to relevant facilities in accordance with
statutory regulations. The crossed-out wheeled bin indicates the product needs
to be disposed separately and not as municipal waste.
Consequently you comply with your legal obligations and contribute to environmental
protection!
PRODUCT SUPPORT
Visit http://www.rclogger.com/support or call +852 2559 2662 for product support.
Additionally visit our Online Ticket System at http://support.rclogger.com for any RC
Logger inquiry.
FCC COMPLIANCE STATEMENT
FCC ID: 2AARVRCL-Datalink
Statement according to FCC part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
> This device may not cause harmful interference, and
> This device must accept any interference received, including interference that may
cause undesired operation.
Statement according to FCC part 15.21
Modications not expressly approved by this company could void the user’s authority to
operate the equipment.
TECHNICAL DATA
Battery ..............................LiPo 1S 40 mAh
Charging ...........................5V/DC via USB, 40 mA
Range ............................... Mobile device
Datalink Quadcopter (via transmitter): max. 1000 m
Bluetooth ..........................BLE4.0
Operating environment .....dry weather conditions
Operating temperature .....0 to 45 °C (+32 to +113 °F)
Storage temperature .........-10 to +45 °C (+14 to +113 °F)
Dimensions .......................49 x 32 x 14 mm
Weight ..............................approx. 15 g
Datalink: max. 10 m
FUNCTION TEST
Make sure you test the following items outlined in the below table before take-off:
Test How
Charge status and low battery Turn the datalink on and refer to the table in
section “Indicator lights” on page 1.
Pairing Refer to paragraph “Pairing” on page 2.
Telemetry data and task points - Assign test task points to your quadcopter.
- Conrm reception of telemetry data.
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. The operating instructions reect
the current technical specications at time of print.
© 2016 by CEI Conrad Electronic International (HK) Limited 89134RC_v1_0116_02_m_en_(8)
Loading...