RC Logger 89115RC Operating instructions

Installation instructions

SAFETY INSTRUCTIONS

NovaX Retractable Landing Gear

No. 89115RC

INTENDED USE

Please download the latest version of the installation instructions from our website at www.rclogger.com. Navigate to the product page and open the ”Downloads” tab. Click on ”Operating instructions” to start the download.

Make this product available to third parties only together with its installation instructions.

The retractable landing gear designed for the NovaX 350 offers advantages over the

regular landing gear. For instance, you can y closer to the ground or if using a gimbal

the gear does not obstruct the view. The retractable gear is controlled via an auxiliary

2-position switch on the transmitter. The product must not become damp or wet. For safety and approval purposes (CE), you must not rebuild and/or modify this product.

If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting, re, electric shock etc. Read the instructions carefully and keep them. Make this product

available to third parties only together with its instructions.

DELIVERY CONTENT

> Retractable gear unit > 4x spring (2 spare springs) > 2x sleeve > Allen key > Installation instructions

WHAT YOU NEED

(all are not supplied)

> Philips screw driver (small) > Screwdriver with hex head (size: 2) > Pair of pliers

Read the installation instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in these instructions, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

Consult the »NovaX 350 manual for instructions on how to attach, connect and operate accessories. Mind the max. takeoff weight.

> The product is not a toy. Keep it out of the reach of children and pets. > Do not leave packaging material lying around carelessly. These may become

dangerous playing material for children.

> Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

> Do not use the product in rain. > Do not place the product under any mechanical stress. > If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed if the product:

» is visibly damaged, » is no longer working properly, » has been stored for extended periods in poor ambient conditions or » has been subjected to any serious transport-related stresses.

> Please handle the product carefully. Jolts, impacts or a fall even from a low height can

damage the product.

INSTALLATION

For your safety, remove the propellers and the flight battery before you start installing the retractable landing gear.

Study the installation diagrams on the following pages before you start the installation process.

1. Remove the ight battery from the NovaX 350.

2. Remove the propellers from the NovaX 350.

3. Turn the NovaX 350 upside down and place it on a soft surface.

4. Unpack the retractable legs and lay all parts out.

5. Start by removing the camera platform. [ 1 ]

6. Disconnect the receiver and remove it.

7. Unhook the rubber strap holding the ight battery in place.

8. Remove the 4 screws that hold the centre piece for the landing gear in place. [ 2 ]

9. Lift the centre piece out of the NovaX 350’s body. To do so, push the clamping piece

out from the bottom a little to release the rubber strap. [ 2 ]

10. Remove the dampers from the centre piece. [ 2 ]

11. Install

dampers

the direction. [ 3 ]

12. Insert the new centre piece into the NovaX 350’s body. [ 4 ]

13. Insert and loop the rubber strap by guiding it through the slot in clamping piece. [ 4 ]

14. Push the clamping piece into the slots in the centre piece and bolt the centre piece

down. [ 4 ]

15. Insert a long leg (side with the longer end) on either side into the retract mechanism. [ 5 ]

16. Lock the legs in place by tightening the 4 bolts on each side. [ 5 ]

17. Push a sleeve onto each skid with bolt facing towards bottom of skid and tighten the bolt

on each sleeve. [ 5 ]

18. Push skids onto the legs (red landing rubber pointing to nose of NovaX 350). Make

sure the balls lock in place. [ 5 ]

19. Install a spring on either side. [ 6 ]

20. Mount the receiver again and connect the receiver cables.

21. Replace the camera platform. [ 7 ]

and clamping piece on the new centre piece for the rectractable legs. Mind

ELECTRICAL CONNECTION

22. Remove the canopy from the NovaX 350.

23. Guide the cables of the retract motors along the inside of the battery compartment

towards the nose of the NoxaX 350 then up and along the sides of the two front electronic speed controllers (ESC) to the power board. [ 8 ]

24. Connect the cables of the retract motors to the RETRACT header pins on the power

board on the corresponding sides. Mind the direction of the nose on the connector as

indicated next to the header pin. [ 8 ]

25. If there is a lot of cable slag the canopy cannot be mounted properly. Remove slag by

carefully pulling the cables towards the nose and then locking them by guiding them carefully between the electronic speed controllers of the two front motors. [ 8 ]

26. Secure each cable by means of a cable tie on the NovaX 350’s body. [ 8 ]

27. Replace the canopy.

FUNCTION TEST

If you use the RC Logger R8 Radio System (89102RC) a 2-position switch has been assigned to the rectractable legs during the learning procedure.

If you use your own transmitter, assign a 2-position switch to channel 7 (Ch 7).

28. Turn on the transmitter.

29. Insert the ight battery and establish the power connection.

30. Assign a 2-position switch to channel 7.

» Not applicable to RC Logger R8 Radio System 89102RC.

31. Hold the NovaX 350 up into the air. [ 9 ]

32. Flip the 2-position switch assigned to channel 7 to test retraction and lowering of the

landing gear. [ 9 ]

» RC Logger R8 Radio System 89102RC: Switch ‘SWA’ (Ch 7). Position 1:

Landing gear is lowered. Position 2: Landing gear retracted.

33. Install the propellers again.

34. Installation and test completed. [ 10 ]

TECHNICAL DATA

Working voltage ................................. 4.8 V – 6 V

Working current ................................. max. 900 mA at 4.8 V, max. 1000 mA at 6 V

Signal Input ........................................ PWM (High-pulse width: 800 us – 2200 us)

Servo travel ....................................... approx. 60°

Working temperature ......................... +14 to 122 °F (-10 to +50 °C)

Operating environment ...................... outdoors only (dry weather conditions)

Height ................................................ 258 mm (installed on the NovaX 350)

Width ................................................. max. 455 mm (installed on the NovaX 350)

Weight ............................................... approx. 95 g (excluding carbon ber landing gear)

NOTES

> Do not continuously ip the switch assigned to the retractable landing gear. > It is not possible to stop the gear when being retracted or lowered respectively. In other

words, the landing gear is either fully lowered or retracted and will always complete a

fully cycle (‘fully down’ or ‘fully up’).

> Do not place the NovaX 350 on the ground with landing gear retracted and then lower

the landing gear.

> Do not put weights on the landing gear.

CLEANING AND CARE

> The product does not require any maintenance, do not disassemble it. Maintenance or

repairs may be carried out by a professional only.

> Do not let liquid enter the retract motors. > Clean the exterior of the retract motors using a clean, soft, dry cloth only. > Do not use any aggressive cleaning agents or chemical solutions as these may

damage the housing causing discoloration and/or malfunction.

DISPOSAL

In order to preserve, protect and improve the quality of environment, protect human health and utilise natural resources prudently and rationally, the user

should return unserviceable product to relevant facilities in accordance with statutory regulations. The crossed-out wheeled bin indicates the product needs

to be disposed separately and not as municipal waste.

Consequently you comply with your legal obligations and contribute to environmental

protection!

PRODUCT SUPPORT

Visit http://www.rclogger.com/support or call +852 2559 2662 for product support. Additionally visit our Online Ticket System at http://support.rclogger.com for any RC Logger inquiry.

These installation instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. The installation instructions reect the current technical specications at time of print.

+ 2 hidden pages