RCA SV 929RX, SV-M24NR, RTS202 E User Manual
User manual
Manual de usuario
RTS202 E
It is important to read this instruction book prior to using your new product for the first time.
Es importante que lea este libro de instrucciones antes de usar su producto nuevo por
primera vez.
EN
EN
For your safety
The AC power plug is polarized (one blade
iswider than the other) and only fits into AC
power outlets one way.
If the plug won’t go into
the outlet completely, turn
the plug over and try to
insert it the other way. If
it still won’t fit, contact
a qualified electrician to
change the outlet, or use a different one.
Do not attempt to bypass this safety feature.
Caution:
To prevent electric shock, match wide blade
of plug to wide slot of power outlet, then
fully insert.
Removing the power plug is the only way to
completely remove power from your product.
Make sure the power plug remains easily
accessible.
Note:
This unit is designed and manufactured
to respond to the Region Management
Information. If the Region number of a
DVD disc does not correspond to the Region
number of this DVD player, this player cannot
play the disc. The Region number for this DVD
player is Region 1.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, whic h can be determ ined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reo r ien t or relo cate t he rece ivin g
antenna.
• In creas e th e sep ar at ion bet we en the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
WARNING:
Changes or modifications to this unit not
expressly approved by the party responsible
for compliance could void the user’s authority
to operate the equipment.
Ventilation
You must adequately ventilate the product.
Make sure there is adequate space around the
unit to provide proper air flow for ventilation.
See diagram.
This product complies with DHHS Rules 21
CFR Subchapter J. Applicable at the date of
manufacture.
videotape of very poor picture quality, or
even impossible.
It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, or rent
copyrighted material without permission.
This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
Important battery information
• Do not mix different types of batter ies
or new and old batteries. Do not use
rechargeable batteries.
• In order to avoid any risk of explosion,
observe the polarities indicated inside
the battery compartment. Replace only
with the type of batteries specified. Do
not dispose of them in a fire or recharge
them.
• If you are not using the remote control
for a long period of time, remove the
batteries.
• Battery shall not be exposed to excessive
heat such as sunshine, fire or the like.
Please respect the environment
and prevailing regulations.
Before you dispose of batteries
or accumulators, ask your dealer
whether they are subject to
special recycling and if they will
accept them for disposal.
Illustrations contained in this document are
for representation only.
Caution
• Th is pr od uct uti liz es a la se r. Use of
controls or adjustments or performance
of procedures other than those specified
herein may result in hazardous radiation
exposure. Do not open covers and do not
repair yourself. Refer servicing to qualified
personnel.
The lightning flash with an arrowhead
symbol, within the equilateral
triangle, is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to cause an electric shock.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in this owner’s manual.
Important Information
FCC Information
This system has earned the
ENERGY STAR.
Caution
Invisible laser radiation when open. Avoid
exposure to beam. Class 1 laser product. This
system must be opened only by qualified
technicians to prevent accidents caused by
the laser beam.
Service information
This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.
Main plug is used as the disconnect device,
it shall remain operable and should not
be obstructed during intended use. To be
completely disconnected the apparatus from
supply mains, the main plug of the apparatus
shall be disconnected from the mains socket
outlet completely.
DVD copy protection
In accordance with the DVD standard, your
DVD player is equipped with a Copy Protection
system, which can be switched on and off
by the DVD disc itself, in order to make any
recording of the relevant DVD disc onto a
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme du NMB-003 du
Canada
WARNING
To reduce the risk of fire or electric shock, do
not expose this product to rain or moisture.
No objects filled with liquids, such a vases,
should be placed on the apparatus.
EN
EN
Please read and save for future
reference
Some of the following information may not
apply to your particular product; however,
as with any electronic product, precautions
should be observed during handling and
use.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
• Do not install near any heat sources such
as radiators,heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
• Do not de feat th e sa fety pu rp ose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
is provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
• Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
• Only use attachments/accessories specied
by the manufacturer.
• Use only wi th the cart, stan d, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
• Unplug this apparatus during lightning
storms or when unused for long periods
of time.
• Ref er all servic ing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
Additional safety information
• Apparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
• Always leave sufcient space around the
product for ventilation. Do not place
product in or on a bed, rug, in a bookcase
or cabinet that may prevent air flow
through vent openings.
• Do not place lighted candles, cigarettes,
cigars, etc. on the product.
• Connect power cord only to AC power
source as marked on the product.
• Care should be taken so that objects do
not fall into the product.
• Do not attempt to disassemble the cabinet.
This product does not contain customer
serviceable components.
If your product operates
on batteries, adhere to the
following precautions:
A. Any battery may leak electrolyte if mixed
with a different battery type, if inserted
incorrectly, or if all batteries are not
replaced at the same time.
B. Any battery may leak electrolyte or explode
if disposed of in fire or an attempt is made
to charge a battery not intended to be
recharged.
C. Discard leaky batteries immediately.
Leaking batteries can cause skin burns or
other personal injury. When discarding
batteries, be sure to dispose of them in
the proper manner, according to your state/
provincial and local regulations.
Important Safety Instructions
Portable Cart Warning
Table of Contents
Connections and Setup ........... 2
Connecting the antennas ...............................2
Connecting AUDIO from external sources
such as TV (Aux-In) .........................................3
Connecting to your TV ...................................4
Connecting the subwoofer ............................5
Positioning the subwoofer ............................5
Other connection options ..............................5
Using of wall mount brackets ........................5
Installing the Sound Bar to the wall ..............5
Overview of Controls ..............6
Front panel controls .......................................6
Remote control functions ..............................7
Using remote control to navigate through
the on-screen menus ......................................7
Playing Discs -
Basic Functions ........................8
Compatible discs .............................................8
Compatible formats .......................................8
Regional coding .............................................8
Operating the Sound Bar ...............................8
Loading a disc .................................................8
Basic playback operations ..............................8
Types of menus ...............................................9
The Info Menu .........................9
Using the Info menu ......................................9
Title/chapter (DVD)/track (audio CD) ...........10
Time display ..................................................10
Audio (DVD) .................................................10
Subtitles (DVD) .............................................10
Camera angle (DVD) .....................................10
Play mode (all discs except JPEG) .................10
Creating a Program List for Program Play
Mode (Audio CDs and DVD discs) ................11
Bookmark (DVD and audio CD) ...................11
Sleep ..............................................................11
Introscan (CD) ...............................................11
JPEG Files ...............................12
Displaying JPEG files .....................................12
Aux-in .....................................12
Connecting auxiliary components ...............12
Selecting Aux-In mode .................................12
Sound output in Aux-In mode .....................12
Radio ...................................... 13
Manual tuning ..............................................13
Storing radio stations ...................................13
Automatic preset programming ..................13
Manual preset ..............................................13
Retrieving preset stations ............................13
The Setup Menu .................... 13
General Setup ...............................................14
Language Setup ...........................................15
Audio Setup ..................................................16
Video Setup ..................................................16
Surround Sound Effects ........17
Additional Information .........17
Troubleshooting ...........................................17
Precautions ...................................................18
Compatible Formats .....................................19
Limited Warranty ..................20
EN
2
EN
3
• Leave enough space around the unit to
allow adequate ventilation: 10 cm/4 inches
on either side and above the top, and 5
cm/2 inches at the rear.
• The humid ity of th e room sh oul d not
exceed 75%. If you have to use the unit
outdoors, do not expose it to rain or
splashing water. The apparatus should not
be exposed to dripping or splashing and
no objects filled with liquids, such as vases,
should be placed on the apparatus.
• Moving the unit from a cold place to a
warm one can cause condensation on
some components inside the unit. Let the
condensation disappear on its own before
turning the unit on again.
• Before moving the unit, make sure the disc
tray is empty.
• Where the mains plug or an appliance
coupler is used as a disconnect device,
the disconnect device shall remain readily
operable.
• Oth e r im p ort a nt u s e a nd cl eani ng
information at the end of the booklet.
Connecting the antennas
The AM and FM antennas connect to the AM
and FM terminals on the system’s back panel.
They must be hooked up in order to receive
clear reception.
AM Loop Antenna
1. Uncoil the AM Antenna wire.
2. Press down on the Antennas tab to open
the terminal.
3. Make sure the white wire on the AM
loop antenna is inserted into the AM loop
terminal and the other wire is inserted into
the ground loop terminal.
Connections and Setup
Remote control and
2xAAA batteries
External AM
loop antenna
Subwoofer
Accessories provided
Wall Mounting Hardware
Wall-mounting hardware included to
facilitate mounting of sound bar on
wall. It’s recommended that mounting be
carried out by a professional. Additional
or alternative parts may be needed for
attachment to specific types of wall
construction.
FM ANTENNAAM LOOP
GND
Antenna
White
FM Pig-Tail
antenna wire
Composite
Video Cable
Things to consider before you
connect
• Ensur e that the ma ins supp ly in your
house complies with that indicated on the
identification sticker located on the back
of your unit.
• Install your unit horizontally, away from
any source of heat (fireplace) or appliances
creating strong magnetic or electric fields.
The components of this unit are sensitive to
heat. The maximum ambient temperature
should not exceed 35°C/95°F.
Using AUDIO IN (AUX 1) jacks
Connect the AUDIO IN (AUX 1) jacks from
the rear panel of the unit to the AUDIO
OUT jacks on TV, Set Top Box, VCR or other
component.
Using AUDIO IN (AUX 2) jacks
Connect the AUX IN (AUX 2) jacks on the front
panel of the unit to the AUX OUT (AUDIO
OUT) jacks on VCR, TV, Set Top Box or other
component.
• Audio cables (color-coded in red and white) (not included) are required.
• To listen to the audio input from the connected component, press SOURCE on
the main unit or AUX1/2 on the remote control to select AUX 1 or AUX 2 mode.
• Refer to the owner’s manual of
the connected TV as well.
• When using HDMI cable, set
the HDMI Audio to PCM.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing
LLC.
Connecting to your TV
Method 1 (best)
HDMI
• Connect the HDMI OUT jack on the rear
of the unit to the HDMI IN jack on your
TV using a HDMI cable (not included).
• Press the HDMI but ton on the rem ote
control to change output signals as follows:
480p, 720p, 1080i and 1080p.
Connecting AUDIO from external sources such as TV (Aux-In)
EN
4
EN
5
• If your television is a high
definition television with an HDMI
input, we highly recommend you
use use the unit’s HDMI output to get
the highest possible video resolution.
• If your television does not have HDMI
input but does support Progressive
Scan, we recommend you use the
unit’s progressive scan output. Set the
Progressive Scan option in the Video
menu to On.
• If one of the devices is not working,
check that all the cables have been
inserted properly into the jacks.
• If your component has only one input
for audio (mono), connect it to the
left (white L/Mono) audio jack on the
TV and don’t connect the right audio
part of the cable.
Connecting the subwoofer
Press down the tab to open the terminal and
insert the subwoofer speaker wire. Release the
tab to lock wire in the terminal.
Note: It is not recommended
to place the subwoofer near
the TV set.
Positioning the subwoofer
A subwoofer is designed to reproduce
powerful low bass effects (explosions, the
rumble of spaceships, etc.).
It can be placed either vertically or horizontally.
For best effects, allow at least two inches of
clear space over the speaker driver and the
port hole.
Use of Rubber Pads
Attach the included rubber pads to the
subwoofer to avoid mechanical vibration
noise, especially when placing the subwoofer
on a hard surface. Attached the rubber pads
to the corners of the subwoofer for maximum
stability.
Other connection options
There are several ways in which you can
incorporate your unit into an Audio-Video
system. This depends on the sockets and
other appliances you have. Sound and image
quality depend to a large extent on the types
of connections used.
1. Coaxial Digital Audio Input
The coaxial digital audio input is compatible
with Dolby Digital (Surround Sound) and
PCM (Digital Stereo) signals when compatible
components are connected. Typical compatible
devices include HDTVs, DVD players, Cable or
Satellite set top boxes.
2. Subwoofer Audio Out
For your convenience, this product is equipped
with a subwoofer preamp output, allowing you
to connect an optional powered subwoofer
(not supplied), if you so desire. Simply use an
RCA cable to connect a powered subwoofer
to the SUBWOOFER AUDIO OUT jack. If you
connect another powered subwoofer, you
must disconnect the supplied subwoofer
speaker to avoid interference.
Using the wall mount bracket
Use the wall mounting hardwares (supplied) to
secure the brackets into your Sound Bar.
Use the 1:1 Wall Mount Template (supplied)
to drill holes in the wall. If attaching to a wall
constructed of drywall and wooden studs, you
must position the Template to ensure the drill
holes align with the centers of the wooden
studs in the wall.
If your wall is of drywall and stud construction,
we recommend you use the following
hardware (not included):
a. 2 pcs. woodscrews, size #8x2”
b. 2 pcs. washers, size #8
wall
1:1 Wall Mount Template
Washer
drill here
Wood screw
• We recommend that
Wall Mounting be carried out
by a professional. Additional
or alternative parts may be
needed for certain type of
wall constructions.
• Bef or e h a n gin g t o t h e
wall, plea se make all AV
connections.
Method 2 (good)
Component video jacks (Pr, Pb, Y)
• The component video jacks are color-coded
green, blue and red.
• Additional component video cables (not
supplied) are required to provide best
picture quality. They are usually colorcoded green, blue and red.
• Connect the component video OUT jacks on
the unit to the component video IN jacks
on your TV so the video content goes from
the unit to the screen.
Method 3 (basic)
Composite video jack (yellow)
• Th e ba si c vide o jack is co lor -c ode d
yellow.
• Video cable (yellow) for the connection
for good picture quality.
• Connect the video OUT jack on the unit to
the IN jack on your TV so the video content
goes from the unit to the screen.
Installing the Sound Bar to the wall
EN
6
EN
7
Overview of Controls
1
6789 10 11
2345
Front panel controls
1. ON / STANDBY – Turns the unit on and
puts it in standby mode.
2. SOURCE – Selects the input sources. Press
repeatedly to select:
DVD – to watch DVD videos
AUX 1 or AUX 2 – to listen to the audio
input from the connected TV, VCR or Set
Top Box.
TUNER – to listen to the radio
COAXIAL – listen to a connected device
(e.g. Set Top Box) with coaxial digital
audio output to enjoy digital audio sound
from the connected device.
3. Display Lens – display unit’s
information.
4. Volume +/- button – adjusts the
volume.
5. Open/close button – open and closes
the disc tray.
6. Play/pause button – starts/pause playing
a disc.
7. Stop button – stops disc playback.
8. REV button – directly accesses the
previous chapter (DVD) or track (CD).
9. FWD button – directly accesses the next
chapter (DVD) or track (CD).
10. Disc tray
11. AUDIO IN (AUX 2) jacks – connects
audio devices.
HDMI
/
/
Remote control functions
ON•OFF – Turns the unit on and puts it in standby mode.
DVD – Selects the DVD mode.
TUNER – Selects the TUNER and selects between FM/AM.
In FM mode, press and hold TUNER to enter into “Auto
Preset Programming”.
COAXIAL – Selects the coaxial mode.
AUX 1/2 – Selects the Auxiliary input (for listening to audio
input from connected TV, VCR or Set Top Box) at front or
rear panel.
0-9 – Number entry.
CLEAR – Quits the current setting manually from the TV
screen without saving change.
INFO – Accesses the Info menu.
TITLE – Accesses the title menu of DVD discs.
DISC MENU – Accesses the disc menu during playback.
OK – Confirms your selection.
– To navigate through the menus. The left and
right arrows also tune the radio frequency in the tuner
mode. When viewing JPG images, use the left/right arrows
to rotate the images. Up arrow rotates image vertically and
down arrow rotates the image horizontally.
MUTE – Mutes and restores the sound.
SETUP – Enters Setup menu.
RETURN – In DVD mode, returns to the previous menu.
VOL +/- – Adjusts the sound volume.
CH +/
, CH –/ – Directly accesses the next or previous
chapter (DVD) or track (CD). Selects programmed stations
in TUNER mode.
REV – Starts reverse accelerated play or reverse slow
motion.
PLAY – Starts playing a disc.
FWD – Starts forward accelerated play or forward slow
motion.
STOP – Stops playback. Press and hold to open the disc
tray.
PAUSE – Freezes frame, accesses frame advance.
SLOW – Accesses slow motion function.
AUDIO – Accesses the audio function; selects between Stereo
and Mono mode for Tuner (FM).
ANGLE – Accesses the camera angle function for DVD
disc.
ZOOM – Accesses the Zoom function.
SUBTITLE – Selects the subtitle languages or turns subtitle
off (if available).
HDMI – Toggles HDMI video output signals modes (480p,
720p, 1080i or 1080p).
EN
8
EN
9
SUBWOOFER – Selects among subwoofer
output levels (soft/balance/strong/powerful).
RANDOM – Turns on/off random playback on
CDDA/JPEG discs.
REPEAT – Accesses the repeat function.
EQ. LEVEL – Toggles channels for different
channel level settings. Adjusts the value using
buttons.
(DOLBY VIRTUAL SPEAKER) – Change
the surround sound setting between Stereo
and Dolby Virtual Speaker settings.
TUNER +/– – Tunes up and down the radio
frequencies.
MEMORY – Stores a station.
Using remote control to navigate
through the on-screen menus
Use and OK on the remote control
to navigate through the on-screen displays
(the DVD player’s menu, the Info Display that
appears during playback, or a disc’s menu).
Use
on the remote to move through
on-screen menus in the direction of the arrow
button (e.g., to move right, press >). The arrow
buttons are used to highlight an option. Once
highlighted, press OK to select the option that
is highlighted.
Insert 2 “AAA”(“UM-4”/”R03”)
batteries to the remote control
prior to use.
Playing Discs - Basic Functions
Compatible discs
• DVD, DVD-R,DVD-RW
• CD, CD-R, CD-RW
Compatible formats
• DVD, JPEG, CD
Regional coding
Your unit has been designed to process
regional management information stored on
DVD discs. The regional code for your unit is
1. Discs that have a different regional code
will not be played.
Operating the Sound Bar
1. Turn on your television set.
2. Press ON•OFF on the remote or ON/
STANDBY located on the unit’s front panel.
Press DVD on the remote control.
Loading disc
1. Press on the front panel or press and
hold STOP on the remote control to open
the disc tray.
2. Insert a compatible disc into the disc
slot.
3. Press
again to close the disc tray.
Basic playback operations
Playback
Switch the unit and the TV set on.
1. After loading a disc, playback starts
automatically, or the disc menu appears.
If the disc menu appears, select the Play
option to begin playback.
2. Press STOP to stop playback.
Accelerated play
While the disc is playing, press REVERSE or
FORWARD one or more times to vary the
speed and direction of the accelerated play.
Press PLAY to resume normal playback.
Pause
While the disc is playing, press PAUSE once for
freeze frame. Press PLAY to resume normal
playback.
Frame advance
1. Press PAUSE twice. FRAME is displayed.
2. Press FWD to move forward one frame at
a time.
3. Press PLAY to resume normal playback.
Variable slow motion
1. While the disc is playing, press PAUSE once.
PAUSE is displayed.
2. Press REV or FWD a number of times to
vary the speed.
3. Press PLAY to resume normal playback.
Changing chapter/track
While the disc is playing, press the CH+/button to go immediately to the next or
previous chapter, or to the next or previous
track.
Zoom
1. While a disc is playing, press ZOOM until
you reach the zoom size you want. The
ZOOM button toggles through 2x, 3x, 4x
and then zooms out to 1/2x, 1/3x and 1/4x,
then returns to normal playback.
2. Move from one area to another (pan) using
the arrow buttons.
3. To turn ZOOM off, press ZOOM unitil you
get to the ZOOM OFF option.
Types of menus
• Disc menu — The appearance and contents
of this menu varies according to the type
of disc you have inserted. It is separate
from the Setup menu.
• Info menu — The unit’s Info menu appears
at the top of the screen while the disc is
playing. Press INFO on the remote to switch
the Info menu on or off.
• Setup menu — Press SETUP to access this
menu.
When you press STOP, the unit
stores the point where playback
was interrupted. If you press PLAY again,
playback resumes from this point. To stop
playback completely or to start again from
the beginning, press STOP twice. If the unit
is left in STOP mode for more than five
minutes without any user interaction, a
screen saver is activated. At the end of 30
minutes without any user interaction, the
unit switches off automatically.
The Info Menu
Using the Info menu
1. Press INFO on the remote while a disc
is playing to display the Info menu. The
first banner shows title, chapter, and time
display information.
2. Press INFO again for audio language,
subtitles, and camera angle.
3. Press INFO a third time for play mode,
bookmark and sleep timer.
4. Use the right/left arrow buttons on the
remote to select an icon.
5. Use the up/down buttons to scroll through
the options.
INVALID KEY will be displayed
if the function you select is not
available.
DVD Info Display
CD Info Display
EN
10
EN
11
Title/chapter(DVD) /track(audio CD)
To directly access a title, chapter (DVD) or an
audio CD, press INFO, press OK. Select the
Title(TT), Track(TRK) or Chapter(CH) icon and
enter a number directly with the numeric
buttons. Press OK again to confirm.
Time display
To access the Time Display, press INFO on the
remote. Press the up/down buttons repeatedly
to display:
DVD: Chapter elapsed time, Chapter remaining
time, Title elapsed time and Title remaining
time.
Audio CD: Track elapsed time, track remaining
time, disc elapsed time, disc remaining time.
To directly access a location on the disc which
does not correspond to the start of a title
or chapter, press INFO once and press OK,
highlight the Time Display icon using the
arrow buttons, then enter a time with the
number buttons (hh:mm:ss) and press OK.
Audio (DVD)
Some discs have several audio tracks used
for different languages or different audio
formats.
To change the language or audio format
during playback:
1. Press the INFO button twice.
2. Use the left/right arrow buttons to select
the Audio icon, or press the AUDIO button
on the remote control.
3. Choose a language or an audio format
with the up/down arrow buttons.
This option is only available if the disc offers
dialog languages or audio formats. When you
change the dialog language using the Info
menu, it only changes the dialog language
of the disc being played. When you eject the
disc or switch off the unit, the language will
revert to the one you selected in the Language
Setup menu.
Subtitles (DVD)
Subtitles are turned off by default. Turn on
Subtitles as follows:
1. While the disc is playing, press INFO twice,
then select the Subtitles icon using the left/
right arrow buttons.
2. Select a language using the up/down
arrow buttons.
3. To turn subtitles off, select the Off option
or press SUBTITLE on the remote.
When you change the language of the
subtitles using the Info menu, it only applies
to the disc currently being played. When you
eject the disc and switch off the unit, the
subtitles will default to the subtitle language
you selected in the Languages menu (see
page 15). This function may not be available
on all discs.
Camera angle (DVD)
Some discs offer different camera angles for
specific scenes.
1. To change the camera angle, press the
ANGLE button on the remote or press the
INFO button twice and select the Camera
angle icon with the left/right buttons.
2. Choose the angle with the up/down
arrow buttons.
Play mode (all discs except JPEG)
1. While the disc is playing, press the INFO
button twice for a CD and three times for
a DVD.
2. Select the Play Mode icon using the left/
right arrow buttons.
3. Use the up/down arrow buttons to select
an option.
• DVD pla y mod es: standa rd , pro gr am,
A-B repeat, title repeat, chapter repeat.
Program play mode is only available if a
program list has been created (see below).
Repeat mode is only available with discs
that display elapsed time and remaining
time. To repeat a sequence between points
A and B, choose the A-B repeat option, and
then follow the instructions for entering
the two points.
Many discs only have one title.
Time display function may not
be available on all discs.
If the disc was recorded using a
single camera angle, this function
is not available.
• Audio CD play modes: standard, introscan,
random, program, repeat A-B, repeat disc,
repeat track.
4. To stop repeat playback, select the Play
Mode icon and use the up/down arrow
buttons to choose the Standard option.
Creating a Program List for
Program Play Mode
(Audio CDs and DVD discs)
To use program play mode, you must first
create a program list.
1. To create a program list, press the INFO
button twice for CD and three times for
DVD. Highlight the Play Mode option and
press the up arrow to select the Program
option.
2. Press OK. The Program screen is
displayed.
3. The first spot in the list is highlighted. Use
the number buttons on the remote to enter
a track number. As for DVD discs: T stands
for Title while C stands for Chapter.
4. Use the arrow buttons to move to the
next spot in the list. Enter the next track
number.
5. Continue entering tracks until you have
completed your list.
6. Highlight the Play option at the bottom of
the screen and press OK or press PLAY to
start playback. The program list will play
in the order you programmed it.
To stop program play, press STOP or select
Standard from the Play Mode option in the
INFO display.
If you want to cancel the list, repeat steps 1
and 2 to select CLEAR and press OK.
Bookmark (DVD and audio CD)
1. Press INFO twice for CDand three times for
DVD. Select the Bookmark icon with the
left/right buttons, and press OK. A menu
is displayed with five bookmarks.
2. The first bookmark space is highlighted.
Press OK to set the bookmark. The book
mark is saved and is indicated by the
number 1. You can set up to five bookmarks
on a disc.
3. To start playback from a bookmark, press
the PLAY button on the remote.
4. To delete a bookmark, highlight it and
press CLEAR.
Sleep
1. Press INFO twice for CD and three times
for DVD. Select Sleep icon with the left/
right arrow buttons.
2. Select one of the available options using
the OK button: Off, 30, 60, 90 or 120
minutes.
Introscan (CD)
This option plays the first ten seconds of each
track on a CD.
1. Press the INFO button twice, then select
the Playmode icon with the left/right arrow
buttons.
2. Press the up/down arrow buttons to select
the INTRO option and press OK to start
IntroScan.
3. Press STOP to stop Introscan, and press
PLAY to resume normal playback.
This function is only available
with discs whose elapsed time
or remaining time appears in the Info
menu.
This function is not available
in AUX, TUNER and COAXIAL
mode.
Loading...