Rca RP5010, RP5012 User Manual

IMPORTADOR

Comercializadora Thomson de Mexico, S.A. de C.V.

Miguel de Cervantes Saavedra 57

Col. Ampliacion Granada

C.P. 11529 Mexico D.F.

Telefono: (52) 25 81 53 20

R.F.C.: CTM-980723-KS5

0137

US Cover 1/21/02, 10:05 AM2

Thomson multimedia Inc.

10330 N. Meridian St.

Indianapolis, IN 46290

©2002 Thomson multimedia Inc.

Trademark(s) © Registered

Marca(s) © Registrada(s)

Marque(s) © Deposée(s)

55287490 (Rev. 0 EN/E)

www.rca.com

u s e r m a n u a l

D

IG

IT

A

L

V

O

IC

E

R

E

C

O

R

D

E

R

E

R

A

S

E

O

P

T

IO

N

V

O

L

U

M

E

RP5010
RP5012

IT IS IMPORTANT TO READ THIS INSTRUCTION BOOK PRIOR TO USING YOUR NEW PRODUCT FOR THE FIRST TIME.
ES IMPORTANTE LEER ESTE MANUAL ANTES DE USAR POR VEZ PRIMERA SU EQUIPO.

US Cover 1/21/02, 10:05 AM3







CAUTION

RISK OF ELECTRIC SHOCK
DO NOT OPEN

THE LIGHTNING
FLASH AND ARROW­HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.

CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER­SERVICEABLE PARTS IN­SIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.

WARNING:

TO PREVENT FIRE

SHOCK HAZARD,



DO NOT EXPOSE THIS PRODUCT

OR ELECTRICAL

TO RAIN OR MOISTURE.

RP5010 8/9/02, 6:00 PM1

FCC information

FCC Information

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
In accordance with FCC requirements, changes or
modifications not expressly approved by Thomson
multimedia Inc. could void the user’s authority to
operate this product.
This device generates and uses radio frequency
(RF) energy, and if not installed and used properly,
this equipment may cause interference to radio
and television reception.
If this equipment does cause interference to radio
or television reception (which you can determine
by unplugging the unit), try to correct the
interference by one or more of the following
measures:

• Re-orient the receiving antenna (that is, the
antenna for the radio or television that is
“receiving” the interference).

• Move the unit away from the equipment that is
receiving interference.

• Plug the unit into a different wall outlet so that
the unit and the equipment receiving interference
are on different branch circuits.
If these measures do not eliminate the
interference, please consult your dealer or an
experienced radio/television technician for
additional suggestions. Also, the Federal
Communications Commission has prepared a
helpful booklet, “How To Identify and Resolve
Radio TV Interference Problems.” This booklet is
available from the U.S. Government Printing
Office, Washington, DC 20402. Please specify stock
number 004-000-00345-4 when ordering copies.

For Your Records

In the event that service should be required, you
may need both the model number and the serial
number. In the space below, record the date and
place of purchase:

Date of Purchase:

Place of Purchase:

Service Information

This product should be serviced only by those
specially trained in appropriate servicing
techniques. For instructions on how to obtain
service, refer to the warranty included in this
Guide.

• Please respect the environment! Before
throwing any batteries away, consult your
distributor who may be able to take them
back for specific recycling.

EN

RP5010 8/9/02, 6:00 PM2

1

Contents

General controls---------2-3

EN

The display-------------------4
Display messages---------5
Before you begin ---------6
Setting the time-----------7
Basic operation------------8
Recording mode-----------9

Recording quality /
condition--------------------10
Other functions-----------11
Erasing file / folder------12
Advanced operation----13
Troubleshooting tips---14
More information-------15
Warranty----------------16-18

RP5010 8/9/02, 6:00 PM3

General controls

The Front

Built-in
microphone

ERASE:
erases file

MENU: Folder, record
condition, record
quality, AVR, playback
mode, key tone, set
year/day/12/24/time,
key lock on/off

DIGITAL VOICE RECORDER

ERASE

MENU VOLUME

EN

Recording
indicator

external
microphone
jack

VOL UP:
volume up

VOL
DOWN:

volume
down

Built-in
speaker

Note: Auto power off- the unit will turn off
automatically without key activation in 3 minutes.

RP5010 8/9/02, 6:00 PM4

2

General controls

EAR

EN

REC: starts/

pauses recording

STOP: stops
playback/
recording. Turns
off the unit.

PLAY: turns the
unit on. Starts/
pauses playback.

FORWARD: skips and
searches forward.
Selects/Browses under
menu mode

REVERSE: skips and
searches backward.
Selects/Browses under
menu mode

Connects
headphones

EA

R

D

C

3V

Connects AC/
DC adapter
(3V)

3

RP5010 8/9/02, 6:00 PM5

The display

The Display

Folder
Number
(1-4)

Current
File
Number

Total
Number of
files in a
folder

Total Remaining
Time for recording

Play/
Record

FOLDER

DICT

REMAIN HQ

SP

DDMM

ONE

ALL

CONF

AVR

EN

Battery level
indicator

Key
Lock

Time/ Date/
recorded time

AM
PM

AM/
PM

Playback mode:
Play one
Play all

Recording
Conditions

Automatic
Voice
Recording

Recording
Qualities

RP5010 8/9/02, 6:00 PM6

4

Display messages

EN

ALL

APPEND

CUT-E

CUT-S

DELETE

MM/DD

12 HOUR

TIME

INSERT

INTRO

OFF

ON

SEN 07

TONE

NO TONE

VOL 15

YEAR

LOCKED

* ( )- You can find the mentioned displays as you set/ operate them.

ALL= Select all (Introductory Play back & Erasing All
Files)

APPEND= Appendix (Adding Appendix)

CUT-E= Cut End (Cutting)

CUT-S= Cut Start (Cutting)

DELETE= Delete (Erasing Selected File & Erasing All files)

MM/DD= Month / day entry mode.

12 HOUR= 12 hour time display mode.

TIME= Time entry mode

INS= Insertion (Inserting New Segments)

INTRO= Introduction (Introductory Playback)

OFF= Off (Automatic Voice Recording)

ON= On (Automatic Voice Recording)

SEN 07= Sensitivity Level (AVR)

TONE= Beeping sound on(Setting Beep Sound)

NO TONE= No beeping sound (Setting Beep Sound)

VOL 15= Volume (Setting Volume)

YEAR= Year (Setting Year)

LOCKED= key locked

5

RP5010 8/9/02, 6:00 PM7

Before you begin

Power supply

This unit can be operated by 2 AAA
batteries or 3V DC power supply.

Installing Batteries
(not included)

1. Slide the battery compartment door
to the bottom and lift up the door to
open.

2. Insert 2 AAA batteries with
polarities matching indications.

3. Replace the battery compartment
door.

Refer to the battery
level indicator on
display for batteries
level. Replace with new
batteries when the
indicator is empty.

Using AC/DC adaptor
(not included)

1. Connect the AC/DC adaptor to the
DC jack on the unit.

2. Connect the AC/DC adaptor to the
wall outlet.

Auto power shut
down

The unit will be automatically turned
off if left idle for 3 minutes.

Using headphones and
external microphone

• When headphones are connected,
sound output from speaker will be
muted.

• When external microphone is
connected, no record can be made
from built-in microphone.

Keys lock

This feature avoids accidental key
activation during recording or
playback.

1. Press and hold MENU button for 2

seconds, LOCKED will be shown on
display. (LOCK icon will lit)

2. Press and hold MENU button for 2

seconds again to unlock keys.

TipsTips

Tips: keys lock function can be

TipsTips

activated in any mode.

Tones

You can activate this feature so that
beep sound can be heard whenever you
press on any button except during
playback and recording.

1. Press MENU button

repeatedly until TONE
shows on display.

2. Press REVERSE or

FORWARD to set beep
sound ON/ OFF.

3. Press MENU to

confirm selection.

6

EN

RP5010 8/9/02, 6:00 PM8

Setting the time

Year/Date/12/24/Time

EN

Setting

With this function, you can always
read on the display the recording date
and time of your recorded messages.
Follow the steps below for time
setting.

You can still use this unit for normal
recording without setting the time.
However, no correct recording date
and time can be referred for your
recorded messages and the display will
keep flashing when the unit is turned
off.

1. Turn on the unit.

2. Press MENU repeatedly to enter
Time setting mode.

3. When “YEAR”
flashes, the digits
of the year blinks
(default is 2002).
Press REVERSE or
FORWARD to
increase/decrease
the number, press MENU to
confirm.

4. Once the year is entered , the digits
in the month
field will blink
(default is 01).
Press REVERSE or
FORWARD to
increase/decrease

the number, press MENU to

confirm.

5. Once the month is entered, the
digits in the day will blink(while the
digits in the month field stop
blinking). Press REVERSE or
FORWARD to increase/decrease the
number, press MENU to confirm.

6. Once the date is
entered, you can
choose between
12/24 hour clock
display by pressing

REVERSE /
FORWARD, then

press MENU to
confirm.

7. Once the time is entered, the digits
in the hour field will blink (default
setting is 12 (12
hour mode) & 0
(24 hour mode).
Press REVERSE or
FORWARD to
increase/decrease
the number, press
MENU to confirm.

TipsTips

Tips: Press

TipsTips

mode.

STOP STOP

STOP to exit to Stop

STOP STOP

7

RP5010 8/9/02, 6:00 PM9

Basic operation

Manual recording

1. In STOP mode, select folder (1-4).

2. Press RECORD to start recording.
(recording time will be displayed once
you press RECORD)

3. To pause recording, you can press
RECORD once, press again to resume
recording.

4. To stop recording, press STOP.

TipsTips

Tips: To view the remaining time for

TipsTips

recording, you may press
recording.

PLAY PLAY

PLAY during

PLAY PLAY

Folder selection

You can select a specific folder (1-4)
for recording. Default is folder 1.
(Refer to page 11 for details)

Recording quality(SP/HQ)

You can select between two recording
qualitieS. Default is SP.
(Refer to Recording quality / condition
section (p.10) for details.)

Recording condition
(DICT/CONF)

You can select between two recording
conditions. Default is DICT.
(Refer to Recording quality / condition
section (p.10) for details.)

Normal Playback

1. In Stop mode, select folder (1-4).

2. Select file by pressing REVERSE or
FORWARD.

3. Press PLAY to start playback.

4. Press PLAY to pause playback, press
again to resume.

5. You can press VOL UP (+) or VOL
DOWN (-) to adjust listening volume.

6. Press and hold REVERSE or
FORWARD to make quick search
within a file.

7. Press REVERSE or FORWARD once
to skip one file forward or backward.

8. Press STOP to stop playback.

Playback mode

You can select to play one file at a
time (Play one) or play all files in the
folder continuously (Play all). Default
is Play one.

Introscan

You can quick scanning the
beginning 3 seconds of each file in a
folder.
(Refer to page 11 for details)

File editing and more...

More advanced editing features for
you convenience.
(Refer to page 12-13 for details)

EN

RP5010 8/9/02, 6:00 PM10

8

Recording mode

Setting Recording

EN

Mode

You can select between two recording
modes - manual recording and AVR
(automatic voice recording).

1. Manual Recording

Please refer to page 8.

2. AVR (Automatic
Voice Recording)

This feature allows the unit to sense
sound and to record only when you
are speaking into the microphone.
When dictation stops for about 3
seconds, recording will stop and then
start again automatically when you
resume dictation.

1. Select destination folder (1-4).

2. Press MENU
three times.

3. Press REVERSE
or FORWARD to
toggle between
AVR on and AVR
off.

4. Press STOP to
exit to STOP mode.

5. Press RECORD to enter AVR mode.

6. During recording,

adjust the sensitivity of
the microphone by
pressing VOL UP and
VOL DOWN, SEN with
sensitivity value shows
on display (e.g.
increase sensitivity value when
recording source is far from the unit or
the recording envionment is quiet.).

7. Start dictation. Recording starts

automatically.

8. Press STOP to end AVR recording.

9. Repeat step 2 and select AVR OFF

for de-selection.

Tips:

• The first syllable or two may be
lost when you start recording
because this ‘sound’ is used to turn
on the AVR feature. It is a good
pratice to make some ‘sounds’ or say
a short word to activate the AVR
before you begin actual dictation.

9

RP5010 8/9/02, 6:01 PM11

Recording quality / condition

Setting Recording
Quality

You can select between two recording
qualities. Default is SP.

Definition

• SP (Standard Play) - allows about 160

min recording on RP5010, 320 min on
RP5012.

• HQ (High Quality) - allows about 60
min recording on RP5010, 120 min on
RP5012.

1. Press MENU
button three times,
(SP or HQ show on
display.)

2. Toggle between
SP and HQ by
pressing REVERSE
or FORWARD.

3. Confirm selection
by pressing MENU
or STOP button.

Setting Recording
Condition

You can select between two recording
conditions. Default is DICT.

Definition

• CONF (Conference) - in a more open

area and recording source is far from
the unit.

• DICT (Dictation) - in a more enclosed

area and recording source is close to
the unit.

1. Press MENU twice

until DICT or CONF
show on display.

2. Select recording

condition by
pressing REVERSE
or FORWARD.

3. Confirm selection

by pressing MENU
button. (You may
press STOP to exit
from further
selection.)

Tips:

• For conferences, to obtain optimum
recording quality, place the recorder with
the microphone freely exposed to the
sound source as close as convenient. A
built-in automatic recording level control
will set record level for optimum
recordings during manual recording. Avoid
recording near unwanted noise sources,
such as air conditioners or fans.

EN

RP5010 8/9/02, 6:01 PM12

10

Other functions

IntroScan

EN

This feature allows playback of the
beginning 3 seconds of each file in a
folder.

1. Select folder (1-4).

2. Press REVERSE or
FORWARD until ALL
shows on display.

3. Press PLAY to start
introductory playback,
INTRO shows on
display.

4. Press PLAY to start
playing desired file.

5. Press STOP to exit
Intro Scan sooner.

Play one / play all

You can choose to play a specific file
or all files in a folder.

1. In STOP mode, press MENU button
repeatedly until ONE appears on
display..

2. Press REVERSE or FORWARD to
toggle between ONE and ALL.

Searching folder

You can select a specific folder (1-4)
for recording. Default is folder 1.

1. Press MENU
button in stop mode.

2. The folder number
will blink on display.

3. Press REVERSE or
FORWARD to select
folder.

4. Press STOP to exit
to stop mode in the
desired folder.

NoteNote

Note: You can record up to 99 files in

NoteNote

one folder, not exceeding 200 files in
total.

11

RP5010 8/9/02, 6:01 PM13

Erasing file / folder

Erasing selected file

You can delete a file by the folowing
steps:

1. Select folder (1-4)

2. Select file.

3. Press ERASE once and DELETE will
blink on the screen.

4. Press and hold ERASE to confirm
deleting. (or press STOP to cancel
erasing file)

TipsTips

Tips: file numbers that come after

TipsTips

erased one will be moved forward by
one automatically.

Erasing all files in a
folder

You can delete all files in a specific
folder by the folowing steps:

1. Turn on the unit.

2. Select folder (1-4).

3. In Stop mode, press

FORWARD

continuously until
“ALL” appears on
display.

4. Press ERASE and
“delete” will blink on
display.

5. Press and hold
ERASE for about 2 seconds, all files in
the selected folder will be erased
completely (or press STOP to cancel
erasing all files).

Erasing All Folders

You can delete all files in all folders by
following steps.

1. Select a folder.

2. Press ERASE once and DELETE will

blink on the screen.

3. Press and hold
RECORD for 2
seconds (Folder/All /
DELETE will flash at
the same time).

4. Press and hold
ERASE for 2 seconds
again to confirm deleting.

EN

RP5010 8/9/02, 6:01 PM14

12

Advanced operation

EN

CAUTION

• The edit function does not operate
when battery power is too low.

• After editing a message, “WAIT” will
be displayed. Do not power off the
device until “WAIT” disappears.

Insert

You can insert new segments into a file
without erasing previously recorded
content.

1. Select folder.

2. Select file for inserting new
segment.

3. Start playback.

4. Press RECORD to
start recording new
segment, “INS” and
elapsed recorded time
will be shown on
display.

5. Press STOP to stop recording.

Append

You can add appendix (e.g.
reminder, supplementary
information) to the end of the file.

13

1. Select folder.

2. Select file for adding appendix.

3. Start playback.

4. Press PLAY to
start playback.

5. During playback,
press MENU once,
“APPEND” will be
shown on display.

6. Press RECORD within 5 seconds to
start recoring appendix.

7. Press STOP to stop recording.

Cut

You can erase unwanted parts from
your recording.

1. Select folder.

2. Select file.

3. Start playback of the file with the
unwanted part.

4. Press ERASE to
mark the start of the
unwanted part, “CUT­S” shows on display.

5. Press ERASE to
mark the endof the
unwanted part, “CUT­E” shows on display.

6. Press ERASE agin
to confirm cutting (or
press STOP to cancel)

Tips: Cutting, inserting new segments
and adding appendix will only update
the recorded time length, without
changing recording time and date.

RP5010 8/9/02, 6:01 PM15

Troubleshooting tips

Unit doesn’t turn on

• Check that batteries are properly
inserted and not exhausted.

• Make sure battery compartment door
is properly closed.

• Make sure LOCK function is not
activated.

Display keeps flashing when unit is
off

• You may not have set the time. Refer
to section on Time Setting.

Cannot record

• Make sure LOCK function is not
activated.

• Make sure memory is not full.

• Check the total files in all folders
not exceeding 200.

• You have recorded 99 files in one
folder. Try record in a new folder.

Cannot show recording date and
time during playback

• You may have not set the date and
time before recording. Refer to section
‘Time Setting’.

No sound from speaker during
playback

• Make sure volume is not set to 0.

• Headphones should not be
connected.

Cannot edit

• Make sure LOCK function is not
activated.

Cannot activate the unit after
pressing on keys

• There may be software problems.

Press and hold RESET to reset the unit.

Recordable time

• You may have set the recording

quality to ‘High Quality’, refer to
section ‘Setting Recording Quality’.

Cannot perform playback

• Make sure you have selected folder

with recorded messages.

• Make sure LOCK function is not

activated.

Cannot erase recorded file(s)

• Make sure you follow each step

under section “Erasing Selected File”
carefully.

becomes shorter

EN

RP5010 8/9/02, 6:01 PM16

14

More information

Precautions for the Unit

EN

• Do not use the unit immediately after
transportation from a cold place to a
warm place; condensation problem
may be resulted.

•Avoid shock to the unit especially
during recording. Recorded data can
be damaged.

• Do not store the unit near fire, places
with high temperature or places with
direct sunlight.

• Do not operate or store unit in places
with frequent static electricity or
electrical noise (e.g. speaker, TV set).

• Clean the unit with a soft cloth or a
damp chamois leather. Never use
solvents.

• The unit must only be opened by
qualified personnel.

• Do not expose this appliance to rain
or moisture.

Precautions for Batteries

• If you do not use the unit for more

than one month, be sure to remove
the batteries to avoid leakage.

• When installing batteries, be sure

that the polarities are correct.
Reversing polarity may cause
personal injury and damage to the
batteries.

• Never mix new batteries with old

ones. Do not mix battery types.

•Discard leaking batteries

immediately. Leaking batteries can
cause skin burns or other personal
injury.

• Do not dispose of in fire.

• Do not charge batteries which are

not intended to be recharged.

15

Precautions for AC power

• Before operating the unit in a new
area for the first time, it is
absolutely necessary to check that
the operating voltage of your unit is
identical to the voltage of your local
power supply.

• Remove the power jack from the
unit if battery power is being used.

• If the unit is not used for a period
of time, remove the plug from the
AC mains.

• AC/DC adapter is for indoor use in
dry rooms only.

Power Supply

•(battery power) AAA x 2,

•(AC/DC power) 3V 200mA.

DC 3V

RP5010 8/9/02, 6:01 PM17

US limited warranty

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year from date of purchase.
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the
rental firm, whichever comes first.

What we will do:

• Provide you with a new, or at our option, a refurbished unit. The exchange unit is under warranty for
the remainder of the original product’s warranty period.

• Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product
is within the warranty period must be presented to obtain warranty service. For rental firms, proof of
first rental is also required.

How to make a warranty claim:

• Properly pack your unit. Include any cables, etc., which were originally provided with the product.
We recommend using the original carton and packing materials.

• Include evidence of purchase date such as the bill of sale. Also print your name and address and a
description of the defect. Send via standard UPS or its equivalent to:

Thomson multimedia Inc.
Product Exchange Center
11721 B Alameda Avenue
Socorro, Texas 79927

• Insure your shipment for of loss or damage. Thomson accepts no liability in case of damage or loss en
route to Thomson.

• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.

• A new or refurbished unit will be shipped to you freight prepaid.

What your warranty does not cover:

• Customer instruction. (Your Owner’s Manual provides information regarding operating Instructions
and user controls. For additional information, ask your dealer.)

• Installation and set-up service adjustments.

• Batteries.

• Damage from misuse or neglect.

• Products which have been modified or incorporated into other products.

• Products purchased or serviced outside the USA.

• Acts of nature, such as but not limited to lightning damage.

EN

RP5010 8/9/02, 6:01 PM18

16

US limited warranty

Limitation of Warranty:

EN

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO
VERBAL OR WRITTEN INFORMATION GIVEN BY THOMSON MULTIMEDIA INC., ITS AGENTS OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY
OF THE CONSUMER. THOMSON MULTIMEDIA INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED
TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply
to you.

• This warranty gives you specific legal rights, and you also may have other rights that vary from state
to state.

If you purchased your product outside the USA:

This warranty does not apply. Contact your dealer for warranty information.

17

RP5010 8/9/02, 6:01 PM19

Canadian limited warranty

Thomson multimedia Ltd. warrants to the purchaser or gift recipient that if any manufacturing defect
becomes apparent in this product within 1 year from the original date of purchase, it will be replaced
free of charge, including return transportation.

This warranty does not include damage to the product resulting from accidents, misuse or leaking
batteries.
Should your product not perform properly during the warranty period, either:

1. Return it to the selling dealer with proof of purchase for replacement,

2. Remove the batteries (where applicable), and pack product complete with accessories in the original
carton (or equivalent). Mail prepaid (with proof of purchase) and insured to:
Thomson multimedia Ltd.
6200 Edwards Blvd.,
Mississauga, Ontario,
L5T 2V7
Canada

The provisions of this written warranty are in addition to and not a modification of or subtraction from
the statutory warranties and other rights and remedies contained in any applicable legislation, and to
the extent that any such provisions purport to disclaim, exclude or limit any such statutory warranties
and other rights and remedies, such provisions shall be deemed to be amended to the extent necessary
to comply therewith.

If you are unable to find a qualified servicer for out of warranty service, you may write to:
Thomson multimedia Inc.
P.O. Box 0944
Indianapolis, Indiana, U.S.A., 46206-0944

Attach your sales receipt to this booklet for future reference. This information is required if service is
needed during the warranty period.

PURCHASE DATE

NAME OF STORE

OR

EN

RP5010 8/9/02, 6:01 PM20

18