RCA PRO808 Owner’s Manual
/"n In r '-/-'17
ILJL Jtlq
nGm'/
Owner's Manual
Product Registration
Please fill out the product registration card and
return it immediately. Returning this card allows us
to contact you if needed.
Keep your sales receipt to obtain warranty parts and
service and lot proof of purchase. Attach it here and
record the serial and model numbers in case you
every need them. The numbers are located on the
bottom Of your camcorder.
AC Adapter/Charger
Before using the AC adapter/charger, read all
instructions and cautionary markings on (1) AC
adapter/charger, (2) battery, and (3) product using
battery.
Caution: To reduce risk of injury, charge only
rechargeable batteries type AV608 or AV8MM.
Other types of batteries may burst causing personal
injury and damage.
Model No. Pro808
Serial No.
Purchase Date:
Purchased From:
2. Extension cord is properly wired and in good
electrical condition, and
3. Wire size below is met:
Minimum Length of Extension
AWG Size Cord (Feet)
18 Equal to or less
than 100
Do not expose the adapter/charger tO moisture of
any kind.
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of.fire, electric shock, or injury to persons..
To reduce risk of damage to electric plug and cord,
pull out the cord with the plug rather than the cord
when disconnecting the adapter/charger from the
wall outlet.
Make sure the cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Use of an improper extension cord could result in a
risk of fire and electric shock. If an extension cord
must be used, make sure that:
1. Pins on the plug of the extension cord are the
same number, size, and shape as those of the plug
on the adapter/charger.
16 Equal to or less
than 150
Do not operate adapter/charger with a damaged cord
or plug. Replace it immediately.
Do not operate adapter/charger if it has received a
sharp blow, been dropped, or otherwise damaged in
any way. Take it to an Authorized RCA Compact
Camcorder Servicenter.
Do not disassemble the adapter/charger. Take it to
an Authorized RCA Compact Camcorder
Servicenter when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock.
To reduce risk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning.
Be sure to save these operating instructions for
future reference.
SAFETY PRECAUTIONS
Your video camcorder's AC adapter/charger will operate on 120-240 volts AC, 50/60 Hz, and has a
polarized plug. Because one blade of the plug is wider than the other, the plug fits in thc wall socket only
one way. Do not defeat the safety feature of this plug. If you need an extension cord, use a polarized
extension cord.
WIDE SLOT, FULLY INSERT.
MISE EN GARDE: POUR PR_VENIR LES CHOCS _LECTRIQUES,
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
INTRODU1RE LA LAME IrA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR
BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. IF YOU SPILL LIQUID ON THE CAMCORDER OR
ADAPTER/CHARGER, DISCONNECT THE AC ADAPTER/CHARGER'S POWER CORD TO PREVENT
POSSIBLE FIRE OR SHOCK HAZARD AND CONSULT AUTHORIZED SERVICE PERSONNEL. MOISTURE
CAN DAMAGE INTERNAL PARTS. REFER ALL SERVICE TO AUTHORIZED RCA COMPACT
CAMCORDER SERVICENTER PERSONNEL ONLY.
CAUTION: READ "IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER" ON THE
PREVIOUS PAGE BEFORE USING THE AC ADAPTER/CHARGER.
CAUTION: MAINTAIN ELECTRICAL SAFETY. POWERLINE-OPERATED EQUIPMENT OR
ACCESSORIES CONNECTED TO THIS UNIT SHOULD BEAR THE UL LISTING MARK OR, IF
PURCHASED IN CANADA, THE CSA CERTIFICATION MARK ON THE ACCESSORIES THEMSELVES
AND SHOULD NOT HAVE BEEN MODIFIED SO AS TO DEFEAT THE SAFETY FEATURES. THIS WILL
HELP AVOID ANY POTENTIAL HAZARD FROM ELECTRIC SHOCK OR FIRE. IF IN DOUBT, CONTACT
QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE CAMCORDER OR
AC ADAPTER/CHARGER TO RAIN OR MOISTURE.
:CAUTION:-- AVOID oPeRATING !_C)OR CAMCORDER i_DIATELY _ MOVING IT FROM
A COLD LOCATION TO A WARM LOCATION, GIVE THE CAMCORDER I-I/2 TO2 HOURS TO .........
REACH A STABLE TEMPERATURE BEFORE INSERTING A VIDEO CASSETTE, WHEN MOVED
CAUTION
DO NOT OPEN
The symbol of a lightning flash within
to the presence of uninsulated
a triangle is intended to alert the user
"dangerous voltage" within the
product's enclosure and which may be
of sufficient magnitude to constitute a
risk of electric shock.
MISE EN GARDE
!:::i._;i.... NE PAS OUVRIR
An exclamation point within a triangle is
intended to alert the user to the presence
of important operating and maintenance
(service) instructions in the literature
accompanying the product.
CAUTION: FCC REGULATIONS STATE THAT ANY UNAUTHORIZED CHANGES OR MODIFICATIONS
TO THIS EQUIPMENT MAY VOID THE USER'S AUTHORITY TO OPERATE IT.
IMPORTANT SAFEGUARDS
In addition to the careful attention devoted to quality
standards in the manufacture of your video product,
safety is a major factor in the design of every instru-
ment. However, safety is your responsibility too.
Thesepages list important information that wil! help
to assure your enjoyment and proper use of a
camcorder, adapter/charger, and accessory
equipment. Please read them carefully before
operating your video products.
Installation
1. Read and Follow InstructionsmAll the safety
and operating instructions should be read before
the video product is operated. Follow all
operating instructions.
2. Retain Instructions--,-. The safety and operating
instructions should be retained for future
reference.
3. Heed Warnings--Comply with all warnings on
the video product and in the operating
instructions.
4. Polarization--This video product is equipped
with a polarized alternating-current line plug (a
plug having one blade wider than the other). This
plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact your
electrician tO replace your obsolete outlet. To
prevent electric shock, do not use this polarized
plug with an extension cord, receptacle, or other
outlet unless the blades can be fully inserted
without blade exposure. If you need an extension
cord, use one with a polarized plug.
5. Power SourcesmThis video product should be
operated only from the type of power source
indicated on the marking label. If you are not sure
of the type of power supply to your home, consult
your video dealer or local power company. For
video products intended to operate from battery
power, or other sources, refer to the operating
instructions.
6. Overloading--Do not overload wall outlets or
extension cords as this can result in a risk of fire
or electric shock. Overloaded AC outlets,
extension cords, frayed power cords, damaged or
cracked wire insulation, and broken plugs are
dangerous. They may result in a shock or fire
hazard. Periodically examine the cord, and if its
appearance indicates damage or deteriorated
insulation, have it replaced by your service
technician.
7. Power-Cord Protection_Power-supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to
cords at plugs, convenience receptacles, and the
point where they exit from the video product.
°
Ventilation--Slots and openings in the video
products are provided for ventilation to ensure
reliable operation of the video product and to
protect them from overheating. These openings
must not be blocked or covered. The openings
should never be blocked by placing the video
product on a bed, sofa, rug, or other similar
surface. This video product should never be
placed near or over a radiator or heat register.
This video product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
video product manufacturer's instructions have
been followed.
Attachments--Do not use attachments unless
o
recommended by the video product
manufacturer as they may cause hazards.
Caution: Maintain elec_cal Safety
Powerline operated equipment or accessories
connected to this unit should bear the UL
listing mark or CSA certification mark on the
accessory itsel.f and should not be modified so
as to defeat the safety features. This will help
avoid any potential hazard from electrical
shoekor fire. If in doubt, contact qualified
service personnel ...........
10. Water and Moisture---Do not use this video
product near water--for example, near a bath •
tub, wash bowl, kitchen sink or laundry tub, in
a wet basement, or near a swimming pool and
the like.
11. Accessories--Do not plac e this video product
On an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing
serious injury to a child or adult as well as
serious damage to the video product. Use this
video product only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer or sold with the video product.
Any mounting of the product should follow the
manufacturer's instructions and use a mounting
accessory recommended by the manufacturer.
llA A video product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the video product and cart
combination to overturn.
2
IMPORTANT SAFEGUARDS
12.
Outdoor Antenna Grounding--If an outside
antenna or cable system is connected to the
video product, be sure the antenna or cable
system is grounded so as to provide some
protection against voltage surges and built-up
static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984
(Section 54 of Canadian Electrical Code, Part 1)
provides information with respect to proper
grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna-
discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection
to grounding electrodes, and requirements for
the grounding electrode. See example below.
Example of Antenna Grounding
WIRE
ROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC.SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION R10-21)
ELECTRIC S POWER SERVICE GROUNDING
EQUIPMENT . ELECTRODE SYSTEM
13.
Power Lines--An outside antenna system
(NEC ART 250, PART H)
should not be located in the vicinity of overhead
power lines, other electric light or power
circuits, or where it can fall into such power
lines or circuits. When installing an outside
antenna system, extreme care should be taken to
keep from touching or approaching such power
lines or circuits as contact with them might be
fatal. Installing an outdoor antenna can be
hazardous and should be left to a professional
antenna installer.
Use
14.
Cleaning--Unplug this video product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
15.
Object and Liquid Entry--Never push objects
of any kind into this video product through
openings as they may touch dangerous voltage
points or "short-out" parts that could result in a
fire or electric shock. Never spill liquid of any
kind on the video product.
16. Lightning--For added protection for this video
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the video product due to
lightning and power line surges.
Service
17.
Servicing--Do not attempt to service this video
product yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
18.
Conditions Requiring ServiceMUnplug this
video product from the wall outlet and refer
servicing to qualified service personnel under
the following conditions.
A. When the power-supply cord or plug is
damaged.
B. If liquid has been spilled, or objects have
fallen into the video product.
C. If the video product has been exposed to rain
or water.
D. If the video product does not operate
normally by following the operating
instructions. Adjust only those controls that
are covered by the operating instructions.
Improper adjustment of other controls may
result in damage and will often require
extensive work by a qualified technician to
restore the video product to its normal
operation.
E. If the video product has been dropped or the
case has been damaged.
F. When the video product exhibits a distinct
change in performance--this indicates a need
for service.
19.
Replacement PartsEWhen replacement parts
are required, have the service technician verify
that the replacements he uses have the same
safety characteristics as the original parts. Use
of replacements specified by the video product
manufacturer can prevent fire, electric shock, or
other hazards.
20.
Safety Check--Upon completion of any
service or repairs to this video product, ask the
service technician to perform safety checks
recommended by the manufacturer to determine
that the video product is in safe operating
condition.
3
Opti Accessories i: ...... :
onal .........." ..........................................:...........................................................
To order accessories, contact your local dealer, call
toll-free, or use the order form on the next page.
AC025A Soft Carrying Case
Custom compact soft
case designed
especially to provide
protection and utility
for your RCA 8ram
camcorder and most
accessories. Rugged
fabric lined with soft
non-abrasive material and generous padding. Has
three outside pockets with storage for lens filters,
adapters, batteries, and tapes.
Rechargeable Batteries
These rechargeable
nickel-cadmium
batteries are
specifically designed
for long life. The
AV608 can power
AV608
AVSMM up to two hours (depending on how much
you use zoom and pause). Both can be recharged
with the AC adapter/charger that came with your
camcorder.
DCC05 Car Cord Adapter/Charger
the vehicle's cigarette lighter socket. It will also
charge the AV608 battery supplied with the
camcorder or the AV8MM long play battery. The
DCC05 is specially designed to convert power from
a 24-volt or 12-volt battery to a 6-volt output.
Caution: Do not use any other car cord with this
camcorder. It may damage the camcorder.
AV8MM
your camcorder up to
one hour, and the
This car cord
adapter/charger enables
you to operate your
camcorder from your car,
truck, or RV .by plugging
the car cord directly into
VDC88 Color Enhancement Light
This uRra compact 15-watt
video light is cordless, light in
weight, and includes a
rechargeable battery. It
inounts on the top of the
camcorder and fits on a standard accessory shoe.
The VDC88 provides excellent soft, lush fill light.
It uses one 15-wat((VDC090) replacement bulb.
The rechargeable battery BP 1000 can be charged
with the VDC085 battery charger.
VCC1000 Video Color Control Center
The VCC1000 is actually two
...._-_>'" _" accessories in one. The color
""-_'__ '_g_--_--£_-control center allows you to
__ adjust the color intensity, tint,
white balance, and sharpness of tapes being dubbed.
This is especially helpful when the original tape was
produced in poor lighting conditions or poor color
settings. The second feature, the character generator,
lets you create titles that can be recorded on your
tapes. This lets you add a professional and/or
personal touch to your home videos.
CRF800 RF Output Adapter
._ This adapter is used with coaxial RF
cable (AH065G or AH066G) to
connect your camcorder to a standard
TV (one without audio/video input
jacks) for playback. If your antenna cable is the flat
twin-lead type attached by two screws, you will also
need a 300-75 ohm transformer such as 193983. If
your TV has 300 ohm VHS screw terminals, you
will need an optional 75-300 ohm transformer such
as AH011.
Coaxial RF Cables
'_-_-_ :_ AH065G (6-ft)
":- AH066G (10-ft)
These RF cables are used with the CRF800 RF
output adapter to connect your camcorder to a
standard TV (one without audio/video input jacks)
for playback.
If your antenna cable is the fiat twin-lead type
attached by two screws, you will also need a 300-75
ohm transformer such as 193983.
If your TV has 300 ohm VHS screw terminals, you
will need an optional 75-300 ohm transformer such
as AH011.
4
193983 Cable Transformer
transfoimer is used
This 300-to-75 ohm
to connect a standard
300-ohm antenna
twin-lead to a standard round 75-
ohm connector.
AH011 Cable Transformer
This 75-to-300
ohm trans-
former is used
to connect a standard 75-ohm
antenna cable, such as AH065G or
AH066G, to the 300-ohm screw
terminals on a TV.
Audio/Video Cables
AH069G (3-ft)
AH070G (5-ft)
These cables are shielded for
connecting A UDIO and VIDEO
jacks. They have RCA-type phono
plugs on each end.
Order Form for Pro808
Description • Part No. Price Qty. Total
Soft Camcorder Case AC025A $ 59.95
Super Lightweight Tripod AC035 $ 69.95
Monopod AC036 $ 39.95
Cable Transformer AH011 $ 1.90
RF Coaxial Cable (6-ft.) AH065G $ 6.99
RF Coaxial Cable (10-ft.) AH066G $ 8.99
Audio/Video Cable (3-ft.) AH069G $ 5.99
Audio/Video Cable (5-ft.) AH070G $ 7.99
Dubbing.Cable(6-ft.) AH075G $ 10.99
Rechargeable Battery AV608 $ 49.95
Rechargeable Battery AV8MM $ 59.95
AC Adapter/Charger CPS08 $189.95
RF Output Adapter CRF800 $ 49.95
Car Cord Adapter/Charger DCC05 $169.95
DC Cable for Adapter/Charger DCC100 $ 14.95
Video Control Center VCC100C $349.90
Color Enhancement Light VDC88 $ 79.95
Replacement Bulb (15 watt)
for VDC88 VDC090 $ 12.95
Extra Battery for VDC88 BP1000 $ 29.95
Charger for BP1000 VDC085 $ 18.95
Cable Transformer 193983 $ 6.95
Replacement Remote Control 217495 $ 49.95
Shoulder Strap 213004 $ 13.95
Audio/Video Cable 217496 $ 7.99
Monaural VCR Dubbing Cable
AH075G (6-ft)
This is a double cable that lets you
connect the AUDIO and VIDEO
jacks of monaural components. It
can be used to connect your
camcorder to a TV monitor
(or VCR). The cable is color coded
and shielded with RCA-type phono
plugs on each end.
All specifications and
descriptions of accessories are
subject to change without notice.
Prices are subject to change without notice.
Total Merchandise ($10 Minimum Order) .......... $
Sales Tax .................................... $
We _ire required by law to collect the appropriate
sales tax for each ihdividual state, county, and
locality to which the merchandise is being sent.
Shipping, Handling, and Insurance ................ $
Total Amount Enclosed ....................... $
Use VISA or MasterCard preferably. Money order
or check must be in U.S. currency only. No COD
or CASH.
• Allow eight weeks for delivery.
• All accessories are subject to availability.
• Where applicable, we will ship a superseding model.
al ! i!i! ii!i!!i!i!iiiiiiiii!iiiiiiiiiiiii!iiiiiiiiiiii iiiii
5.00
5
Accessory Order Form : .......
• __':_"'_ii ...._'_':"_'_'_'_'*:_':'_':_'_:_ii!_iii:'i_i_!!i_!_ii!ii_iiii!iii!iii!i!i?'_!_,_i!ii,!i!!_;_i!,%,i;_i_/,,_!il',,ii!,'i_,,_i,,i_ii_:iii?ili_ii!_iiiiiiii_i!ii_'_,__ii,_!ii!i_!!i!i_!!iiiiiiiiiiii_ili_i!i!i!iiii'_!ii!iii!i,ii!ili!iiiiil,iii!,!i_iiiiil;!!,i.i,_i!i!i_)i2!ilili?_i!!iii!il!!i_iil;_i_ii!iiii_il_i_,_!_
To order accessories, contact your
Charge your order on your VISA
or MasterCard by
filling in below
local Dealer.
If a dealer is not nearby, you can also
follow the directions below to order by
USE YOUR CREDIT CARD
IMI'ORTANT: Copy complctc account ntnnber
from your VISA card
telephone or direct-by-mail.
United States and Canada Orders
To place your order by phone, have your
I lll j7r--I-q7-r--V-1r--T--T'q
Visa or MasterCard ready and call the
toll-free number listed below between
My card expires: f-T'-]
8AM and 8PM Eastern Standard Time.
Use this number only to place an
order for accessory items listed on this
IMPORTANT: Copy complete account number
from your MasterCard
order form.
1 - 800 - 338 •- 0376
IIII Il--l--l-q--q[---I---1---_VT--[---_
Most times your order will be shipped
C°P'N°mb" [ I I II_bo,,eyour expires:
i_alne oll
MasterCard
My card I--T--1 I--T- ]
UPS within 72 hours of receipt. If ever
it is not possible to ship within 30 days,
we will notify you with an update on
your order and an option to cancel.
AUTHORIZED SIGNATURE
Prices arc subject to change without notice.
PLEASE
Nallle:
Street:
City:
State:
Please make surc that both sides of this form have
been filled out completely.
Print or type your name and
address clearly. This will be your
mailing label.
A complete and correct order will
save you days of waiting.
Apt:
Zip:
To place your order by mail, detach and
mail the completed order form with
credit card information, money order, or
check in U.S. currency (made payable to
Thomson Consumer Electronics, Inc.) to
the following address:
RCA Video Accessories
PO Box 8419
Ronks, PA 17573
For more information on these
accessories (or current prices), write
to the following address:
Video Accessories Customer Service
Thomson Consumer Electronics, Inc.
Distributor & Special Products
2000 Clements Bridge Rd
Deptford, NJ 08096-2088
International Orders
¢..)
This offer is valid only in the 50 United
States. For international orders, please
send your request for a price quotation
(not an order) to:
X
International Customer Service
Thomson Consumer Electronics, Inc.
Distributor & Special Products
2000 Ciements Bridge Rd
Deptford, NJ USA 08096-2088
6
AC035 Super I,ightweight Tripod
This tripod's fluid-effect head provides smooth
camera pan and tilt. The quick-release mount makes
it easy to attach or remove the camcorder. The
grooved, tubular 3-section leg design folds down to
23-1/2" when not in use and weighs only 3-1/2 lbs.
Rubber feet allow for sure footing.
AC036 Monopod
This monopod gives a flexible alternative to using a
traditional tripod. It is ideal for all camcorders and
photo cameras. It has a quick release shoe, three-
section leg, handstrap, foot step, and weighs only 35
ounces.
Cautions: Before using a tripod, make sure it is stable enough to hold the camcorder without falling over.
When attaching your camcorder to a tripod or monopod, be careful not to force their screw into the
camcorder's mounting hole.
The tripod or monopod screw should not protrude into the e_eorder more than approximately three-eighth
(318) inch. Forcing the screw could damage the mounting hole on the bottom of the camcorder.
......... : :
7
1. Unpack the camcorder and accessories.
• Save the packing materials and box in case you ever need to ship or store your camcorder.
• The items shown below are packed with your camcorder. If any are missing or appear damaged,
contact your RCA dealer immediately.
1£,% :" l'/
Remote Control Batteries
(Two "AA" 1.5 Volt)
WARNING: NICKEl,
CADMIUM BATTERY
MUST BE DISPOSED
OF PROPERLY.
Camcorder
Model Pro808
• 1
Remote Control
Part No. 217495
AC Adapter/Charger
Part No. CPS081
Q
Clock Battery: 3-Volt Micro
Lithium Cell Battery.
Replace only with - Maxell
No. CR2025 available from
most local drug stores. Use
of another cell may present a
risk of fire or explosion.
8
Shoulder Strap
Part No. 213004
Cautions. Lithium cell batte_. Must be disposed of properly. Never handle
punctured or leaking cells. May cause burns or personal mjt_ry,
Keep out of the hands of children. Can cause death or injury if swaiio_ed. If
swallowed, consult a physician immediately for emergency treatment.
The lithium cell used in this device may explode resulting in a fire or chemical burn
if mistreated. Do not recharge, disassemble, heat above 212°F (100 ° C), or
incinerate.
Never use metallic tweezers to hold the cell, and never short circuit the + and - sides
of the battery.
Rechargeable Battery
Part No. AV608
Caution:
Do not use this
for any other
purpose other than
adapter/charger _
charging the
AV608 or
AV8MM battery
pack or supplying
power to the l)C Connecting Cord Audio/Video Output Cable
camcorder. Part No. DCCI00 Part No. 217496
2. Attach a Power Supply: Adapter/Charger or Charged Battery.
A. Adapter/Charger
I.
Connect one end of the DC power cord
to the DC OUT jack on the adapter/
DC Power
Cord
jack
OUT
Jack
charger and the other end to the DC IN
6.5V jack on the camcorder.
.
Plug in the adapter/charger. The
adapter/charger's POWER indicator
will light.
Details are on page 16.
To AC 100-240V,
50160 Hz
POWER
Indicator
B. Charged Battery*
Match lanes
Slide Battery
3. Attach the shoulder strap.
A. Unfasten one end of the shoulder strap from
the buckle. Leave the buckle on the strap.
1. Make sure the camcorder's POWER
switch is OFF'.
2. Match the lines on the battery and
camcorder.
3. Hold the battery flush against the
camcorder, and slide it in the direction
of the arrow until it locks into place.
* The battery ,nust be charged before it can be used.
Details are on page 17.
C. Thread the strap back into the buckle. Pull on
the strap and make sure it is securely fastened
before using it to support the camcorder.
B. Thread one end of the shoulder strap through
one of the shoulder strap rings.
Shoulder
Strap Rings
D. Repeat steps A-C for the other end of the
shoulder strap.
(continued on next page)
9
Fi
4. Attach lens cap to the lens cap holder.
A. Pull tab on side of the lens cap to remove it
from lens on camcorder.
Tab on
Lens Cap
B. Pull tab end of the lens cap straight out and
rotate it down.
5. Adjust the hand strap.
4
0
C. Attach it to the lens cap holder on the side of
the camcorder.
Lens Cap
on Holder
A. Unsnap the flap and open the adjustment strap.
B. Put your hand in the hand strap.
C. Pull the adjustment strap to tighten.
f
6. Insert a cassette in the camcorder.
OPEN Button
_ Compartment
Cassette
Cover
Cassette
D. Snap the flap closed.
A. Slide the OPEN button, and completely open
the cassette compartment cover.
B. Press the EJECT button to open the cassette
compartment.
nt
C. Insert a cassette with the safety tab facing up
and the tape window facing out.
D. Gently press on the compartment where it is
labeled PUSH until it locks into place.
E. After the cassette compartment is fully
retracted, close the compartment cover.
10
7. Turn on the camcorder and place the ON/POWER SAVE lever ON*.
POWER (CAM/OFbTPLA Y) Switch
\
ON/POWER
SAVE Lever
* If the dew indicator _ appears in the viewfinder, there is excessive moisture in the camcorder.
Remove the cassette from the camcorder, and let it dry naturally.
Viewfinder in Operating
Position (PULL out here.)
A. Press and hold the small button on the POWER switch
while placing it in CAM (camera).
The position of the POWER switch tells the camcorder
whether you want to record (CAM), play back tapes
(PLAY), or turn off the camcorder's power (OFF).
B.Place the ON/POWER SAVE lever ON. This lever must
be ON for the camcorder to record.
Place the ON/POWER SAVE lever in the POWER SAVE
position during recording breaks to conserve battery
power. The camcorder will enter record-pause.
Eyepiece
Focus
Control
A UTO LOCK Switch
Tally Light
.
Set A UTO LOCK switch to A UTO
LOCK.
.
Adjust viewfinder and eyepiece focus
control.
A. Pull the viewfinder into operating position.
B. If the viewfinder picture is blurry, adjust the
eyepiece focus control for your vision.
Details are on page 23.
Earphone
Jack C)
ON/POWER
SAVE Lever
REC START/STOP
Button (Thumb Trigger)
10. Start and stop recording.
A. Press and release the REC START/STOP
button (thumb trigger) to start and stop
recording. REC appears in the viewfinder
during recording.
B. To monitor the audio being recorded, attach
an optional earphone to the earphone jack.
If you do not record within five minutes, the
camcorder will automatically turn off.
The tally light flashes during record-pause
and turns off when the camcorder is
recording or the ON/POWER SAVE lever is
in POWER SAVE.
11
11. Play back what you have recorded.
A. Press the thumb trigger to stop recording.
B. Place the POWER switch in PLAY.
C. Press the REW button to rewind the tape.
D. Press the PLAY button to play back the tape in the viewfinder.
E. Press the STOP button when you are finished playing back the tape.
Details on viewfinder playback are on page 31.
12. Review the camcorder controls.
POWER (CAM (camera)/OFF/PLA Y) Switch
Accessory Shoe
Remote Control Sensor
Micro[
Tally
Lens
FOCUS ON/OFF Button
Also Still (ll) Button
MANUAL FOCUS + and - Button
Power Zoom Buttons (W and T)
Eyepiece Focus Control
Electronic Viewfinder
(PULL here to extend)
ect Lever
F.FWD. (Fast Forward) Button
REW (Rewind) Button
Clock Cell Compartment
Output Jacks (Yellow Video,
DC, and White Audio)
(Located behind cover)
PLAY Button
12
STOP Button
Also MODE SEL. (Select) Button
AUTO LOCK Switch
Loading...