fl at panel solutions
Wall Mount for LCD, Plasma, and
LED Displays
Installation Manual
MAF85BKR
Fits TVs 37”- 60”
Maximum Load
Capacity – 165 lb (75 kg)
Thank you for choosing the RCA MAF85BKR Universal Flat Panel
TV Wall Mount. This mount can be used for all major brands of
37" - 60" fl at panel TVs, 165 lbs (75 kg) or under. This wall mount
features a 0-15-degree tilt for easy viewing. Before attempting
to mount your television set, please remove all parts from this
package and read the installation instructions carefully.
WARNING: Use of this mount with a TV weighing over 165
lbs. or with a screen larger than 60" could cause the mount
to fail causing property damage and/or personal injury.
CAUTION:
This wall mount is intended for use
only with the maximum weight of
75 kg/165 lbs. Use with heavier
than the maximum weights
indicated may result in instability
causing possible injury. Follow
the installation and operation
instructions carefully.
Safety precautions
Follow these precautions to ensure safe installation and mounting of your fl at panel TV.
1. Read these instructions carefully before you begin.
If you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.
2. The wall or mounting surface must be capable of
supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.
3. Safety gear and proper tools must be used. Failure
to do so can result in injury and/or damage. A
minimum of two people are required for installation.
Do not attempt to install this mount alone under any
circumstances.
4. Follow all instructions and recommendations
regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.
5. For drywall installation, it is essential for the
wall mount plate to be attached to wall studs.
(Use a stud fi nder.)
6. Use the included hardware for mounting purposes.
This hardware has been provided to ensure a safe
and secure mount.
7. Hire a licensed electrician to relocate an electrical
outlet, if needed.
8. Be sure to purchase wires long enough to connect
the TV to the audio and video components in your
installation.
Keep your sales receipt to obtain warranty parts and
service and for proof of purchase. Attach it here and
record the model number. This number is located on
the product.
Model No. ____________________________________
Purchase Date _________________________________
Dealer/Address/Phone _________________________
Preparing to install
Before beginning the installation process, verify that you have all the necessary tools on hand. The following
tools are required for proper installation:
Tools
Phillips Head Screwdriver
Ratchet or Driver with 13 mm (1/2”) Socket
Electric or Portable Drill
3/16” (4.8mm) Drill Bit and Stud Finder for Drywall
Installation
3/8” (10mm) Masonry Bit for Concrete Installation
Package Contents
Wall Plate (x1)
Mount Arm (x2)
Tilt Adjustment Rod (x1)
Safety Bar (x1)
Instruction Manual (x1)
Hardware Kit (x1)
Continues on next page...
Pour des instructions
en français, se
reporter à la page 6.
Para obtener
instrucciones en
español, consulte la
página 11.
Hardware Kit
(A) M8 x 63 Lag Bolt (x6)
(F) M8 x 12 Bolt (x4)
(B) Lag Bolt Washer (x6)
(C) Concrete Anchor (x6)
(D) M6 x 12 Bolt (x4)
(E) M6 x 30 Bolt (x4)
(G) M8 x 30 Bolt (x4)
(H) M6 Washer (x4)
(I) Spacer (x8)
(J) 3/16” Drill bit
Mounting the wall plate
Drywall Installation
Important! For safety reasons, this mount must be secured to at least two wood studs no less than 16”
apart. For displays heavier than 50 kg (110 lbs), three studs are recommended. The studs must be capable of
supporting the combined weight of the mount and display.
1. Use a high quality stud fi nder to locate two or
more adjacent studs where you wish to install
your mount. Mark both edges of each stud to help
identify the exact center.
NOTE: You must use the center of each stud
to avoid cracking or splitting the wood during
installation.
2. Place the wall plate against the wall and level it
using the integrated bubble level.
3. While another
person holds
the wall plate in
position, mark four
or six locations
(two per stud) for
securing the mount
to the wall (see
Fig.1).
4. Set the wall plate aside and drill a 3/16” pilot hole at
each marked location.
5. Place the wall plate back against the wall and
attach it using the lag bolts (A) and lag bolt washers
(B) (see Fig. 2). Do not over-tighten these bolts
and do not release the wall plate until all bolts
are in place. Ensure that the wall plate remains
level after all bolts are secured.
Fig.2
Fig.1
2