RCA 52D0207A, M52D User Manual
Choose Your Connections
Make your connection decision easier by taking a few minutes to review the jacks on your new
TV/DVD. Compare the jacks on the device you want to connect and see if the same jacks are
available on your TV/DVD. en refer to the chart below to determine the best connection to
make.
For more information about connecting your TV/DVD to other devices, refer to OWNER’S
MANUAL. Make sure you read the provided safety information before you connect and
operate your TV/DVD.
Jacks Quality Connects to ... Cable needed (not included)
HDMI
PC MONITOR
COMPONENT
Y
Pb
COMPONENT
Y
Pb
COMPONENT
Y
PC/HDMI
AUDIO
VIDEO
S-VIDEO
L(MONO)
AUDIO
VIDEO
S-VIDEO
L(MONO)
AUDIO
VIDEO
S-VIDEO
VIDEO
L(MONO)
AUDIO
RRPr
VIDEO
L(MONO)
AUDIO
RRPr
VIDEO
Devices with an HDMI™ or a DVI
output, such as Satellite
Receivers and Cable Boxes.
Devices with Y Pb Pr
(component) outputs, such as
Satellite Receivers, Cable Boxes,
PVRs, and DVD Players
Devices with S-Video or Video
(composite) outputs, such as
DVD Players, VCRs, Satellite
Receivers, and Cable Boxes
Audio
DVI
Adapter
Component
Video
Audio
S-Video
Audio
Audio
Pb
L(MONO)
Cable
(wall outlet)
AUDIO
OR
L(MONO)
AUDIO
RRPr
Connect a Signal Source
Connect your TV/DVD to cable or an antenna in order to receive
TV channels. Connect the cables as shown in fig.1 or fig.2.
or
Antenna
Note: If you have regular cable, your TV is able to receive some digital
channels because it has a capability called QAM. QAM is a tuner that
enables reception of unscrambled digital cable content. Check with
your cable provider for information about content availability in your
area. Refer to Step 2, Operate Your TV/DVD, for information on viewing
digital channels.
Video
If you’re connecting a cable box or satellite receiver use the chart
above to help determine which jacks to use for the best
connection. Your cable box or satellite receiver needs to be high
definition if you want to receive high definition programming.
Check with your cable provider for more information.
ANT ANT
Continue to Step 2, Set Up Your TV/DVD, on the back page.
TelevisionTelevision
fig.1 fig.2
OR
RCA and asociated marks are trademarks of THOMSON S.A. used under license to TTE Corporation.
HDMI, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Windows Media™ is a trademark of Microsoft Corporation.
J52D0207A SH
52D0207A_QS.indd 152D0207A_QS.indd 1 6/12/09 1:47:43 PM6/12/09 1:47:43 PM
N
fig.3
TV/DVD
Number
buttons
– (DISPLAY)
SETUP/
TV MENU
SCREEN
SIZE
ENTER
▲/▼/◀/▶
DVD
MENU
PLAY
STOP
INPUT
SELECT
Set Up Your TV/DVD
Operate Your TV/DVD
Make sure you have already connected your TV/DVD to devices and a signal source, plugged in the
TV/DVD, and put batteries in the remote.
Now, turn on the TV/DVD and start the setup. (POWER indicator on the front of the unit changes green.
It may take approx. 10 seconds for a picture to appear on screen.)
Starting setup
e Starting Setup menu (fig.3) appears the first time you turn on the TV.
• Set the on-screen language
(If English is your preferred language, you can skip below and advance to the next step.)
Press ◀ or ▶ until your language is shown.
• Choose the Signal Type (Air/Cable selection)
Press ▲ or ▼ to select “Signal Typel”
(If you connected Cable TV service to your ANT jack, you can skip below and advance to the next step.)
Press ◀ or ▶ to choose “Air” (this is for antenna users).
• Automatic Search
Press ▲ or ▼ to select “Automatic Search”, then press ▶ or ENTER to begin the “Automatic Search”.
e search takes some time as it is looking for analog, digital and digital sub channels. Once the search is
complete, the TV/DVD tunes to a channel.
– For more information, see OWNER’S MANUAL, page 15 –
Using the DVD player
To use the DVD player, press TV/DVD (“DVD” appears at the bottom of the screen). Insert a disc into the side
slot load with disc’s label facing towards you. If necessary, press PLAY to play the disc. To switch back to TV
mode, press TV/DVD.
e DVD player can play DVD discs, Audio CD discs, CD-R/RW discs with mp3, Windows Media-formatted
content, and JPEG files.
Using the Menu System
e SETUP/TV MENU button accesses both the DVD player’s main menu and TV’s menu. To access the
DVD player’s main menu, while a disc is playing first press STOP and then press SETUP/TV MENU. Use ▲
or ▼ to scroll up or down; ◀ or ▶ to scroll left or right; and ENTER to make selections.
A disc is capable of having an on-screen menu that is separate from the DVD player’s main menu. e disc
menu might only contain a list of the titles and chapters, or it may allow you to change features such as
language and playback settings. To access the disc menu, press DVD MENU.
Watching TV
Entering Channel Numbers
Digital channels can have both primary channels (like the analog channel number) and sub channels. If 15 is the
primary channel and 1 is the sub channel the channel looks like 15-1 on screen. To tune to a such channel, press
the first 3 digits, then press the – (DISPLAY) button, followed by the remaining 3 digit, as 0, 1, 5, –, 0, 0, 1,
then press ENTER.
Changing Screen Formats
Your TV allows you to change the format of the picture you’ve viewing by pressing the SCREEN SIZE on the
remote control. Depending on the type of signal you’re viewing, you might not be able to change the format.
Viewing Devices Connected to Your TV/DVD
To view devices connected to your TV/DVD, first make sure you are in TV mode. Press INPUT SELECT.
Choose the input where you connected the device.
Your choices are TV, Video, Component, HDMI, PC or DVD (DVD mode).
Thank you for your purchase. Before making a trip back to the retailer, please visit www.rca.com/television for more information or contact us at 1-800-336-1900 so that we
may assist you in operating the unit, replacing missing parts, and ensuring your satisfaction with the product.
Automatic Search Start
Auto Setup
Language English
Signal Type Cable
: Adjust
: Select
52D0207A_QS.indd 252D0207A_QS.indd 2 6/12/09 1:47:44 PM6/12/09 1:47:44 PM
Loading...