RCA L3239E User Manual

fl at panel solutions

Fixed Wall Mount for LCD, Plasma,
and LED Displays

Instruction Manual

Specifi cations

Display Size: 32” to 60”
Maximum Load: 130 lb (60kg)
Mounting Pattern: 600 mm x 400 mm (23.6” x 15.7”) max
Profi le: 1.2” (3.0 cm)

Box contents

Wall Plate (x1)
Mount Arm (x2)
Safety Rod (x1)

Warnings

Instruction Manual (x1)
Hardware Kit (x1)
Template (x1)

MS60BKR

Fits TVs 32”- 60”

Maximum Load

Capacity – 130 lb (60kg)

1. Read these instructions before you begin. If

you are unsure of any part of the process, contact
a professional contractor or installer for assistance.
Improper installation can result in injury or damage.

2. The wall or mounting surface must be capable of

supporting the combined weight of the mount and
the display; if not, the structure must be reinforced.

3. Locate pipes, wires, or any other hazards in the wall

where you wish to install the mount before drilling.

4. Safety gear and proper tools must be used. Failure

to do so can result in injury or damage.

5. Two people are recommended for installation.

Do not attempt to lift a heavy display without
assistance.

6. Follow all instructions and recommendations

regarding adequate ventilation and suitable
locations for mounting your display. Consult the
owner‘s manual for your particular display for more
information.

CAUTION:

This wall mount is intended for use only with the
maximum weight of 60 kg (130 lbs). Use with heavier
than the maximum weights indicated may result in
instability causing possible injury.

Pour des instructions
en français, se
reporter à la page 5.

Para obtener
instrucciones en
español, consulte la
página 9.

Continues on next page...

Tools required

Phillips-Head Screwdriver
Ratchet or Driver with 13 mm (1/2”) Socket
Electric or Portable Drill
5 mm (3/16”) Drill Bit and Stud Finder for Drywall Installation
10 mm (3/8”) Masonry Bit for Concrete Installation
Level

Hardware kit

(A) M8 x 63 Lag Bolt (x2)

(G) M6 x 30 Screw (x4)

(B) Lag Bolt Washer (x2)

(C) Concrete Anchor (x2)

(D) M4 x 12 Screw (x4)

(E) M4 x 20 Screw (x4)

(F) M6 x 12 Screw (x4)

(H) M8 x 12 Screw (x4)

(I) M8 x 30 Screw (x4)

(J) M6 Washer (x4)

(K) Spacer (x8)

Installation

Part 1A – Mounting to the Wall (Drywall)

IMPORTANT! For safety reasons, this mount must be secured to at least two wood studs no less than 16”

apart. The studs must be capable of supporting the combined weight of the mount and display.

1. Use a high quality stud fi nder to locate two adjacent studs where you wish to install your mount. Mark both

edges of each stud to help identify the exact center.

NOTE: You must use the center of each stud to avoid cracking or splitting the wood during installation.

2. Place the mounting template against the wall over the marked studs. Make sure the template is level.

3. Drill two 5 mm (3/16”) pilot holes in the wall using the template as a guide. Drill

one hole per stud (see Fig. 1).

4. Remove the template from the wall and place wall plate against the wall over

the pilot holes.

5. Attach the wall plate to the wall using the lag bolts (A) and lag bolt washers (B)

provided (see Fig. 2). Do not over-tighten these bolts and do not release
the wall plate until both bolts are in place. Ensure that the wall plate

remains level after both bolts are secured.

Fig.1

Fig.2

2