RCA J26L637, J26L637L User Manual

LCD Television
User’s Guide
Changing En ter tain ment. Again.
Important Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualifi ed service personnel.
This symbol indicates "dangerous voltage" inside the product that presents a risk of electric shock or personal injury.
WARNING
To reduce the risk of fi re or electric shock, do not expose this product to rain or moisture. This apparatus shall not be exposed to dripping or splashing. No objects fi lled with liquids, such as vases, shall be placed on the apparatus.
This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts. When servicing use only identical replacement parts.
This symbol indicates important instructions accompanying the product.
Refer to the identifi cation/rating label located on the back panel of your product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifi cations to this equipment may void the user’s authority to operate it.
Caution: Using video games or any external accessory with fi xed images for extended periods of time can cause them to be permanently imprinted on the picture tube (or projection TV picture tubes). ALSO, some network/ program logos, phone numbers, black borders (sides, top and bottom), etc. may cause similar damage. This damage is not covered by your warranty.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in par tic u lar, specifi es that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
Product Registration
Please fi ll out the product registration card (packed separately) and return it immediately. For US customers: Your RCA Consumer Electronics product may also be registered at www.rca.com/television. Registering this product allows us to contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These num bers are located on the product.
Model No. _____________________________________________________________
Serial No. ______________________________________________________________
Purchase Date: _________________________________________________________
Dealer/Address/Phone:__________________________________________________
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
15. If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead­in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See following example.
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
ELECTRIC SERVICE EQUIPMENT
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
11. Only use attachments/accessories specifi ed by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
3
Table of Contents
Important Information .....................................................2
IMPORTANT SAFETY INSTRUCTIONS .................................3
Chapter 1: Connections & Setup
Things to Consider Before You Connect ...........................5
Protect Against Power Surges ....................................5
Protect Components from Overheating ....................5
Position Cables Properly to Avoid Audio
Interference .................................................................5
Use Indirect Light ........................................................5
Remote Control ...........................................................5
Check Supplied Parts ...................................................5
Get the Picture ..................................................................6
Getting Digital Channels.............................................6
Getting Regular (Analog) Channels ...........................6
Rear Jack Panel ...................................................................7
Hospital Pendant .........................................................7
Start-up ...............................................................................7
Plug in the TV ..............................................................7
Put Batteries in the Remote........................................7
Turn on the TV .............................................................7
Place All Available Channels Into Memory ................7
Set the Time ................................................................8
The ClonePRO™ .................................................................8
Understanding the Menus ................................................8
Master Menus ..............................................................8
Basic Menus .................................................................8
Using Master and Basic Menus .........................................9
Setting Limits in Master Menus ..................................9
Sound Menu .......................................................................9
Access and Power Options Menu ...................................10
What to Expect .................................................................11
Watching TV ..............................................................11
Changing Channels ...................................................11
Explanation of Jacks ........................................................12
Buttons and Other Jacks on your TV ..............................13
Chapter 2: Using the Remote Control
Types of Remote Controls ...............................................14
Master Remotes .........................................................14
Basic Remotes ............................................................14
ClonePRO™ ................................................................14
Additional Remote Buttons (R130K2) .............................14
ClonePRO™ Remote Buttons ..........................................15
Chapter 3: Using the Menu System
The Basic Menu System ...................................................16
Sound Menu ..............................................................16
Picture Menu .............................................................16
Access and Power Options Menu .............................16
Parental Control Menu .............................................17
Time Menu .................................................................17
Language & CC Menu ...............................................18
Chapter 4: Using the TV's Features
Channel Banner ................................................................19
Parental Controls and V-Chip ..........................................20
How V-Chip Works for USA and Canada .................20
Lock/Unlock Parental Controls..................................20
US V-Chip TV Ratings ................................................21
Blocking Age-Based Ratings .....................................21
Blocking Specifi c Content Themes ...........................22
Blocking Canadian V-Chip Ratings ...........................22
V-Chip Movie Rating Limit ........................................23
Blocking Movie Ratings.............................................23
Block Channels...........................................................23
Block Digital Channels ..............................................23
Front Panel Lock ........................................................23
Lock Time Menu ........................................................24
Blocking Unrated/Exempt Programs ........................24
Future Rating Region ................................................24
Additional Features .........................................................24
Calendar .....................................................................24
Screen Formats ..........................................................25
Chapter 5: Other Information
Frequently Asked Questions (FAQs) ...............................26
Using the ClonePRO™ .....................................................27
Modes of operation ..................................................27
DSCI mode..................................................................27
IR mode ......................................................................28
Cloning a TV ..............................................................29
ClonePro Troubleshooting ........................................29
Troubleshooting ...............................................................30
Mounting Your TV to the Wall ........................................32
V-Chip Rating Explanations .............................................33
US V-Chip Rating System ...........................................33
Canadian English V-Chip Rating System ..................33
Canadian French V-Chip Rating System ...................34
Autotuning .......................................................................35
Limited Warranty .............................................................36
Care and Cleaning ............................................................37
4
Chapter 1: Connections and Setup
Things to Consider Before You Connect
Protect Against Power Surges
• Connect all devices before you plug any of their power cords into the wall outlet or power
strip. NEVER plug your TV into an outlet that is controlled by a wall switch.
• Turn off the TV and/or device(s) before you connect or disconnect any cables.
• Make sure all antennas and cables are properly grounded. Refer to the Important Safety
Instructions at the beginning of the User's Guide.
Protect Devices from Overheating
• Don’t block ventilation holes on any of the devices. Arrange the devices so that air can
circulate freely.
• Don’t stack devices.
• If you place devices in a stand, make sure you allow adequate ventilation.
• If you connect an audio receiver or amplifi er, place it on the top shelf so the heated air from it
won’t fl ow around other devices.
Position Cables Properly to Avoid Audio Interference
• Insert each cable fi rmly into the designated jack.
• If you place devices above the TV, route all cables down the side of the back of the TV instead
of straight down the middle.
• If your antenna uses 300-ohm twin lead cables, do not coil the cables. Also, keep the twin lead
cables away from audio/video cables.
Use Indirect Light
Don’t place the TV where sunlight or room lighting will be directed toward the screen. Use soft or indirect lighting.
Remote Control
You will need a master remote or ClonePRO™ to set up the TV. Contact your RCA Commercial Distributor to purchase these.
Check Supplied Parts
Check that the following parts were packed with your product.
2 AA batteries
Note: If you need to replace your remote, call 1-800-338-0376. A shipping
Remote Control Part # R130K1
Chapter 1 5
Power cord
Graphics contained within this publication are for representation only.
and handling fee, and the appropriate sales tax, will be charged upon ordering. Have your Visa, MasterCard, or Discover Card ready.
Connections and Setup
ANTENNA/CABLE ANALOG INPUT
Coaxial cable
or
Outdoor or Indoor antenna
ANTENNA/CABLE DIGITAL INPUT
Get the Picture
The fi rst part of connecting your TV is to get the picture, also known as the signal. The back panel of your TV allows you to receive analog channels by using the ANTENNA/CABLE ANALOG INPUT and digital channels by using the ANTENNA/CABLE DIGITAL INPUT. See the graphic to the left for these locations.
Getting Digital Channels
What You Need
• Antenna ("rabbit ears") or outdoor antenna with coaxial cable A. Do you have an indoor or outdoor antenna? If not, go to step B. If so, plug the antenna or
coaxial cable from the wall outlet into the ANTENNA/CABLE DIGITAL INPUT to receive free off-air local digital channels.
B. Do you have a set-top box? If not, go to Getting Regular (Analog) Channels. If so, you need to
call your cable company or satellite service provider. They'll use special cables to allow you to view digital channels. To view your regular channels, go to Getting Regular (Analog) Channels
Step B.
What You Need To Know
• Visit www.antennaweb.org to get help deciding what type of antenna to use to receive the local digital channels available to you. By entering where you live, this mapping program tells you what local analog and digital stations are available using a certain antenna.
• When you get to the Channel setup screen in the Initial Setup, make sure you set the options for using a digital signal source. To complete a channel search now, go to page 7.
• When you are ready to watch channels, make sure you are tuned to the Digital Input. Press the ANTENNA button to tune to the Digital Input (look for D at the bottom of your channel
banner. Go to page 11 for more information).
Getting Regular (Analog) Channels
What You Need
• Antenna ("rabbit ears") or outdoor antenna with coaxial cable
OR
Coaxial cable
or
Outdoor or Indoor antenna
6 Chapter 1
• Coaxial cable with cable
A. Do you have an indoor or outdoor antenna? If not, go to step B. If so, plug the antenna or
coaxial cable from the wall outlet into the ANTENNA/CABLE ANALOG INPUT to receive free off-air local analog channels.
B. Do you have cable? If so, plug the coaxial cable from the wall outlet into the ANTENNA/
CABLE ANALOG INPUT to receive your cable channels.
What You Need to Know
• Visit www.antennaweb.org to get help deciding what type of antenna to use to receive the local analog channels available to you. By entering where you live, this mapping program tells you what local analog and digital stations are available using a certain antenna.
• When you get to the Channel setup screen in the Initial Setup, make sure you set the options for using an analog signal source. To complete a channel search now, go to page 7.
• When you are ready to watch channels, make sure you are tuned to the Analog Input. Press the ANTENNA button to tune to the Analog Input (look for A at the bottom of your channel
banner. Go to page 19 for more information).
Rear Jack Panel
Connections and Setup
REAR PANEL
VGA VGA
VGA
AUDIO
COMPONENT IN 1
Pr/Cr Pb/Cb
Y
AUDIO 1
IN
LR
ANTENNA
Hospital Pendant
This specialized remote control is recognized for use in patient beds. It is used to connect to a pillow speaker, nurse­call system, or other device to supply speaker-level audio or
COMPONENT IN 2
Pr/Cr Pb/Cb
Y
AUDIO 2
IN
LR
AUDIO OUT
RL
VIDEO
OUT
DIGITAL
ANTENNA
HDMI/DVI
accept remote control commands. The connector is a (3-wire) phono jack. Some are simple, having one-button operation of the TV; others have enhanced capability for greater control.
DSCI PORTPENDANT
SIDE PANEL
AUDIO
IN
VIDEO
LR
IN
HEADPHONES-VIDEO
Specifi c models and requirements depend on what other devices are in the hospital room, for example, nurse-call systems. See your distributor for more information.
Start-up
Plug in the TV
Plug the end of the power cord into the back of the TV. Plug the other end into a grounded wall outlet. Insert the plug completely into the outlet. Do not plug into an outlet controlled by a light switch.
Put Batteries in the Remote
• Remove the battery compartment cover from the back of the remote by pushing the tab and lifting off the cover.
• Insert two fresh batteries. Make sure the polarities (+ and -) are aligned correctly.
• Replace the cover.
Turn on the TV
Turn on your TV by pressing the Power button on the front of the TV or ON•OFF on the remote control.
Place All Available Channels Into Memory
1. To go to the Setup menu, with the master remote (R130K2), press MENU then select Setup. In this menu you'll be able to set your Signal Type. Next go to Auto Channel Search, the TV will search for all channels viewable through your antenna or cable TV system.
2. Select which channel list you’d like to fi nd channels for (List A is the default).
3. Press the down arrow button to select Start. Press the OK button to start searching. The TV searches for active channels and places them in the channel list.
Note: Video Input Channels (VID, SVID, etc.) must be added to the active channel list separately before they can be accessed. Refer to the Setup menu section at the end of this chapter for more information on the Channel menu and List & Labels.
Chapter 1 7
Connections and Setup
Set the Time
The current time options might not be available to the basic user, depending on how they've been set by the master user. (The Time Confi guration menu isn't available in the basic menu).
To set the time, from the Main menu select Time then Time Confi g. If the current time has not been set, use the arrow and number buttons on the remote control to make changes.
1. From the Main menu, highlight Time and press OK.
2. Time Confi g. is highlighted. Press the right arrow to enter the menu.
3. Time is highlighted. To set the time press the right and left arrow button to add or subtract minutes. Use the number buttons to set the hour. The OK button changes am and pm.
The ClonePRO™
If several TVs need to be programmed with the same menu settings, an optional ClonePRO remote can be used to copy all of the menu settings from one TV into other TVs to reduce installation time. Information can be both downloaded to and uploaded from the ClonePRO using the DSCI port on the TV’s back panel or using the IR sensor. A ClonePRO can be obtained from your RCA commercial distributor. Chapter 2 has information about this remote, see page 15. If you want to set other menu options before using the ClonePRO, continue on in this chapter. You can use the ClonePRO at any time.
Understanding the Menus
This television displays two levels of menus: master and basic.
Master Menus
The master menus are accessible by pressing MENU on the master remote (R130K2). This menu shows all menu options. The person who chooses the settings available to the basic end user is called the “master user.”
Basic Menus
The basic menus are accessible by pressing MENU on a basic remote (R130K1 or other remote) or the front panel. The choices available on the basic menus and control panels will vary depending on limits set by the master user and the input selected. You can turn off the basic menu completely through the Access & Power Options menu. For more information on the effects of master user choices on the basic menu and basic user functionality, continue on in this chapter.
Note: Options set in the master menu are stored in nonvolatile memory. If any options are changed in the basic menu, and then the TV is turned off, the TV defaults to the master menu settings once it’s turned back on.
8 Chapter 1
Connections and Setup
Using Master and Basic Menus
Menus and choice lists use the “point and select” rule to navigate, but control panels use a variety of methods to adjust features on your TV. The following pages detail how to use these controls to customize the functions of your TV.
Press MENU on the remote (master remote for master menu; basic remote for basic menu) or on the front panel (basic menu) to bring up the Main menu.
To select a menu item:
• Navigate with the arrows and then select OK.
• Navigate with the arrows and then select with the right arrow button (unless it's a choice list).
Setting Limits in Master Menus
Some screens in the master menus are not available in the basic menus. There also might be some options you want to make unavailable to the basic user. These next few pages describe these types of menu options. To make all options unavailable, set the basic menus in the Access & Power Options menu to Disabled. For information on basic menu options, go to Chapter 3.
Sound Menu
Initial Volume Sets the TV’s volume to the specifi ed level every time it is turned on.
Note: When the DSCI (Digital Serial Communications Interface) port is used to turn the TV on and off, Initial Volume settings are nonfunctional.
Minimum Volume Re-scales the volume control slider so that the far left position is always the minimum allowable volume (but not necessarily the minimum possible volume).
Maximum Volume Re-scales the volume control slider so that the far right position is always the maximum allowable volume (but not necessarily the maximum possible volume).
Chapter 1 9
Connections and Setup
Access and Power Options Menu
The Access and Power Options menu allows the master user to specify which features and functions basic users will be able to access. Scroll to the feature you want to set. Use the right arrow button to change the setting.
Go Back Takes you to the previous menu.
Remote Confi g. (Confi guration) This feature allows the master user to determine which TVs
the remote operates. Choose from TV1, TV2, TV3, TV1&2, TV1&3, TV2&3, All or Disabled. The default setting is All. If Disabled is chosen, the TV will not respond to the basic remote, except when MENU from the master remote has been pressed.
Note: Although the TV supports TV3, the master remote cannot be programmed for it.
Basic Menus This setting allows you to determine whether the TV's basic menus are accessible. Choose Enabled or Disabled. When the basic menu is disabled, users cannot access menus through the basic remote or front panel.
TV Power This setting allows you to determine whether the TV can be turned on or off with the POWER button on the remote or the front panel. Choose between:
On Always The TV is always on and cannot be turned off; the Sleep Timer, Schedule and
Energy Saver settings are disabled.
Notes: When On Always is being used, KidPass is unavailable.
When the DSCI (Digital Serial Communications Interface) port is used to turn the TV on and off, the On Always setting is overridden.
Switched The TV can be turned on or off; Sleep Timer, Schedule and Energy Saver can be
enabled. This is the default setting.
Energy Saver Setting When enabled, this feature turns the TV off after a specifi ed period of inactivity (no remote or front panel button presses). You can toggle between Disabled, 2-hour, 1-hour, and 30-minute settings. Disabled is the default setting. If TV Power is set to On Always, Energy Saver settings are ignored. A warning message will be displayed prior to the TV shutting off.
Front Panel This setting determines whether the front panel buttons are active (able to be used to control the TV) or not.
Parental Control This feature determines the amount of access basic users have to Parental Controls. Blocking age-based rating and content themes is described in Chapter 3. Choose between:
Basic&Pwd (Password) Basic users are able to enter the Parental Control menu and change
the password. Basic users can watch blocked programming by entering the system password. This is the default setting.
Basic Basic users are able to enter the Parental Control menu but cannot change the
password. Basic users can watch blocked programming by entering the system password.
NoBasic Parental Control does not appear on the basic Main menu. Basic users can watch
blocked programming by entering the system password.
If Parental Controls is set to NoBasic, Movie Rating Access, TV Rating Access, Unrated Program Block, and Channel Block will not be available to basic users, regardless of what those items have been set to individually in the Parental Controls menu.
10 Chapter 1
Connections and Setup
Min Stdby Power When enabled, keeps power consumption levels compliant with Energy Star standards. The TV is shipped with this enabled. When enabled, the DSCI and Hospital Pendant (pillow speaker jack) are disabled when power is turned off.
Legacy Mode When turned on, allows the TV to work with earlier DSCI versions. Off is the default setting.
Info Menu Allows the master user to determine whether the Channel Banner is displayed when the INFO button is pressed on the remote. Page 24 shows this display.
Hospital Mode When turned on, allows the TV to function with the hospital pendant remote. For more information about this remote, go to page 24.
Note: When Remote Confi g. and Front Panel are set to Disabled, the MENU button on the master remote turns on the TV.
What To Expect
Watching TV
Remember: If you have an analog signal connected to your
ANTENNA/CABLE ANALOG INPUT, then look for an A at the bottom of the screen to make sure you're tuned to the Analog input. Press the ANTENNA button if the A isn't appearing.
10 CBS
A
Look for the A at the bottom of the screen to make sure you're on the Analog Input.
10-1 CBS
D
Look for the D at the bottom of the screen to make sure you're on the Digital Input.
Analog video is sent in a 4/3 format, which your TV displays these
channels in a 16/9 format. Press the LEFT/RIGHT ARROW button to view the different formats available. Go to page 24 for more explanation of screen formats.
Remember: If you have a digital signal connected to your
ANTENNA/CABLE DIGITAL INPUT, then look for a D at the bottom of the screen to make sure you're tuned to the Digital input. Press the ANTENNA button if the D isn't appearing.
Most digital video is sent in a 16/9 format which does fi ll your
screen, but sometimes is sent in 4/3 which does not fi ll your screen. It depends on how the station or source device is formatting the video. If there are bars on-screen, press the LEFT/ RIGHT ARROW button to try a different format that may eliminate the bars. Go to page 24 for more explanation of screen formats.
Changing Channels
• Digital channels can have both primary channels (like the analog channel number) and sub-channels. First tune to the Digital Input by pressing the ANTENNA button and look for a D at the bottom of the screen. To tune to a digital channel with a sub-channel, enter the primary channel number, then press the right arrow button. Enter the sub-channel number and press OK.
• Depending upon the type of signals you have connected to your HDTV, you might notice that the channels change slower than you’re used to. This is perfectly normal. Digital cable channels sometimes take longer to tune.
Chapter 1 11
Connections and Setup
Explanation of Jacks (in alphabetical order)
This section describes the jacks on the back panel of your TV. There are several ways to connect devices.
ANTENNA/CABLE ANALOG INPUT Lets you connect a coaxial cable to receive the signal from the antenna, cable, or cable box.
ANTENNA/CABLE DIGITAL INPUT Lets you connect a coaxial cable to receive the signal from the antenna, digital cable, or digital cable box.
AUDIO Use the Audio Out jacks when using the MONITOR OUTPUT Video jack or use these jacks by themselves to connect an audio receiver to the TV for enhanced sound quality. If you use these jacks to receive your sound, you don't need to connect the speakers supplied with the TV. Make sure you set the Audio output correctly in the Advanced Settings Sound menu. Go to page 28 for more information.
L (Audio) Provides left audio connection. The left audio connector is usually white.
R (Audio) Provides right audio connection. The right audio connector is usually red.
COMPONENT INPUTS Lets you connect a device that has component video jacks, such as a DVD player.
CMP1 Y Pb/Cb Pr/Cr (Component Video) Provides optimum picture quality because the
video is separated into three signals. Use three video-grade or component video cables for the connection. When using CMP1 Y Pb/Cb Pr/Cr, make sure you connect left and right audio cables to the CMP1 L and R AUDIO jacks.
CMP1 L AUDIO Provides left audio connection when using the CMP1 video inputs. The left
audio connector is usually white.
CMP1 R AUDIO Provides right audio connection when using the CMP1 video inputs. The right
audio connector is usually red.
CMP2 Y Pb/Cb Pr/Cr (Component Video) Same as described for CMP1 Y Pb/Cb Pr/Cr and
CMP1 Audio above. Make sure you connect the left and right audio cables to the CMP2 L and R AUDIO jacks.
DSCI PORT This port is used to transfer information between a TV and other devices, such as a clone box or interactive system. This port is an eight-pin telephone-type port. When the TV receives a message via the DSCI (digital serial communications interface) port, it will act in accordance with the digital instructions received. For more information on its connection and operation, please contact your distributor or the supplier of the interactive system.
HDMI/DVI Input Lets you connect a device, such as a digital cable box, with an HDMI or a DVI output.
HDMI/DVI INPUT (High-Defi nition Multimedia Interface/Digital Visual Interface) Provides
an uncompressed digital connection that carries both video and audio data by way of an integrated mini-plug cable. Since HDMI technology is based on Digital Visual Interface (DVI), the jack on the back of your TV is also compatible with DVI devices.
L AUDIO (used for DVI only) Provides left audio connection when using the DVI jack. The
left audio connector is usually white.
R AUDIO (used for DVI only) Provides right audio connection when using the DVI jack.
The right audio connector is usually red.
Note: Remember to connect the left and right audio cables because the DVI cable carries only the picture signal, not the sound.
12 Chapter 1
Loading...
+ 26 hidden pages