21011
2.4 GHz Dual Cordless Handset
Call Waiting Caller ID Speakerphone
User’s Guide
We bring good things to life.
EQUIPMENT APPROVAL INFORMATION
Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts
15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence
Number (REN) for the equipment. You must, upon request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these
devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected
to one line should not exceed 5. To be ce rtain of the number of devices you may connect to your line as determined by the REN,
you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
Notes
• This equipment may not be used on coin service provided by the telephone company.
•Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are
on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this
product does not disable your alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualified installer.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall,
where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable
and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In
case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary
discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint
to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations or procedures where
such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate
notice, in writing, to allow you to maintain uninterrupted service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference; and (2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference).
•Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is
connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet,
“How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number 004-000-0 0345-4 when ordering copies.
HEARING AID COMPATIBILITY (HAC)
This telephone system meets FCC standards for Hearing Aid Compatibility.
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
2
TABLE OF CONTENTS
EQUIPMENT APPROVAL INFORMATION........ 2
INTERFERENCE INFORMATION ................... 2
HEARING AID COMPATIBILITY (HAC)........ 2
INTRODUCTION ..................................... 5
HANDSET AND CHARGE CRADLE LAYOUT .. 7
BASE LAYOUT ...................................... 7
BEFORE Y OU BEGIN .............................. 8
PARTS CHECKLIST ............................. 8
TELEPHONE JACK REQUIREMENTS ........ 8
IMPORTANT INSTALLATION INFORMATION .... 9
IMPORTANT INSTALLATION GUIDELINES .. 9
CONNECTING THE AC
(ELECTRICAL) POWER....................... 10
CONNECTING THE TELEPHONE LINE ..... 10
INSTALLING THE PHONE ........................ 10
INSTALLING THE HANDSET BATTERY .....11
WALL MOUNTING THE BASE ............. 12
TELEPHONE SETUP .............................. 12
PROGRAMMABLE FUNCTIONS............. 12
USING THE SOFT KEYS ............. 12
LANGUAGE..................................... 12
DISPLAY CONTRAST ......................... 13
AREA CODE ................................... 15
RINGER TONE ................................. 16
TONE/PULSE .................................. 17
HANDSET REGISTRATION .................. 18
HANDSET DE-REGISTRATION .............. 21
GLOBAL DEREGISTRATION ................. 22
WALKIE TALKIE ............................... 23
TIME OF DAY .................................. 25
DEFAULT ........................................ 26
BASIC OPERATION ............................... 27
SPEAKERPHONE .............................. 27
CHARGE INDICATOR ......................... 27
MAKING A CALL ............................. 28
HANDSET ............................... 28
SPEAKERPHONE ....................... 28
ANSWERING A CALL ........................ 28
HANDSET ............................... 28
SPEAKERPHONE ....................... 28
CALL TIMER.................................... 29
AUTO STANDBY .............................. 29
RINGER VOLUME SWITCH ................. 29
HANDSET ............................... 29
BASE ............................................ 30
FLASH/CALL WAITING ...................... 30
LAST NUMBER REDIAL ..................... 31
HOLD ............................................ 31
EXIT ............................................. 31
PAGING THE HANDSET...................... 32
PAGING FROM THE BASE OR
HANDSET....................................... 32
TRANSFERRING CALLS...................... 33
MUTE ........................................... 34
TEMPORARY TONE DIALING ............... 35
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
CAUTION:
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
3
CORDLESS HANDSET VOLUME
CONTROL ............................ 35
SPEAKERPHONE VOLUME
CONTROL ............................ 35
INTERCOM ...................................... 36
MAKING AN INTERCOM CALL............. 36
RECEIVING AN INTERCOM CALL ... 37
RECEIVING AN EXTERNAL TELEPHONE
CALL DURING AN INTERCOM CALL ..... 37
BETWEEN HANDSETS................ 37
BETWEEN BASE AND HANDSET .. 37
USING INTERCOM OR
CONFERENCE WITH
EXTERNAL CALLS ................. 37
MEMORY ........................................... 39
STORING A NAME AND NUMBER IN
MEMORY ....................................... 39
STORING A REDIAL NUMBER ............. 41
INSERTING A PAUSE IN THE DIALING
SEQUENCE ..................................... 41
REVIEWING, CHANGING OR DELETING
STORED NUMBERS .......................... 41
TO REVIEW: ............................ 41
TO CHANGE:........................... 42
TO DELETE: ............................ 42
DIALING A STORED NUMBER ............. 43
HANDSET ............................... 43
BASE ..................................... 43
CHAIN DIALING FROM MEMORY......... 44
CALLER ID ........................................ 44
RECEIVING AND STORING
CALL RECORDS ............................... 45
REVIEWING CALL RECORDS ............... 45
TRANSFERRING CID RECORDS
MEMORY................................... 46
TO
DIALING A CALLER ID NUMBER ......... 47
DELETING THE CALLER ID RECORD
SHOWING IN THE DISPLAY ................. 48
DELETING ALL CALLER ID RECORDS .. 49
CALLER ID ERRORS ......................... 50
REPLACING THE BATTERY ...................... 51
BATTERY SAFETY PRECAUTIONS ......... 51
HEADSET AND BELT CLIP
INSTALLATION .............................. 52
CONNECTING AN OPTIONAL
HEADSET TO THE HANDSET................ 52
ATTACHING THE BELT CLIP ................ 52
DISPLAY MESSAGES ............................ 53
HANDSET SOUND SIGNALS .................. 54
TROUBLESHOOTING GUIDE ................... 54
GENERAL PRODUCT CARE .................... 57
CAUSES OF POOR RECEPTION ............... 58
SERVICE ............................................ 58
INDEX ............................................... 59
ACCESSORY ORDER FORM ................... 61
LIMITED W ARRANTY ............................ 62
SAVE THESE INSTRUCTIONS
4
INTRODUCTION
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for
future reference.
Congratulations on purchasing this GE Dual Cordless Handset Telephone
System. This system operates in the 2.4 GHz frequency range, and is unique to
conventional cordless telephones. When the base is connected to electrical
power and a telephone line, it can support up to two cordless handsets, and
you can place a fully featured cordless handset anywhere an electrical power
line is available.
Features:
• 2.4 GHz digital technology
• Handset to handset Intercom
• Speakerphone
• 2-way and 3-way Conference/Call Transfer
• Call Waiting and Caller ID Compatible
•Tone/Pulse Dialing
• 50 Name and Number Memory Locations in each handset and the base
This telephone has been designed to be simple to use, however , you can
reach its full potential more quickly by taking a few minutes to read this
instruction book. This telephone is a multifunction product for use with Call
Waiting and Caller ID services available from your local telephone company.
5
Your Caller ID Call Waiting phone allows you to:
•View the name and telephone number of a caller while you are on the
phone (Call Waiting Caller ID).
• Identify callers before you answer the phone.
•View the time and date of each incoming call.
•Record up to 40 Caller ID messages sequentially in each handset and
the base.
• Know who called while you are on the other line or when you were away.
•Screen unwanted calls, eliminate harassment from annoying calls, or to
get prepared before answering a call.
IMPORTANT: Because cordless phones operate on electricity, you should
have at least one phone in your home that isn’t cordless, in case the power in
your home goes out.
IMPORTANT: In order to use all of the features of this telephone, you must
subscribe to two separate services available from your local telephone
company: the standard Name/Number Caller ID Service to know who is
calling when the phone rings and Call Waiting Caller ID Service to know who
is calling while you are on the phone.
INSTALLATION NOTE: Some cordless telephones operate at frequencies
that may cause interference to nearby TVs, microwave ovens, and VCRs. To
minimize or prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV, microwave ovens, or VCR. If such
interference continues, move the cordless telephone farther away from these
appliances. Certain other communications devices may also use the 2.4 GHz
frequency for communication, and, if not properly set, these devices may
interfere with each other and/or your new telephone. Typical devices that may
use the 2.4 GHz frequency for communication include wireless audio/video
senders, wireless computer networks, multi-handset cordless telephone
systems, and some long-range cordless telephone systems.
6
HANDSET AND CHARGE CRADLE LAYOUT
soft key
Display
format/
conference
button
buttons
handset charge cradle
AC power supply
TALK/callback
button
redial
button
page/int
button
* tone button
BASE LAYOUT
redial button
CID button
volume
button
charge
indicator
page/int. button
e
r
e
n
f
c
n
e
o
c
c
a
l
l
b
format
a
c
k
l
o
v
/
TALK
d
i
c
v
r
e
d
i
a
l
ringerpage
i
n
t
abc
1
3
2
ghi
jkl
4
6
5
pqrs
tuv
7
9
8
tone
oper
#
0
*
soft key buttons
v
v
CID
v
volume
v
charge
page/int.
* tone button
v
h
s
fla
def
mno
wxyz
pause
cid/vol
button
flash
button
ringer
button
# pause button
Display
a
s
l
h
f
g
n
i
e
r
m
r
r
o
e
a
d
f
r
t
i
a
l
c
o
n
f
.
def
abc
1
3
2
mno
ghi
jkl
4
6
5
wxyz
pqrs
tuv
7
9
8
pause
tone
oper
#
0
*
k
c
a
b
l
l
a
c
speaker
speaker/callback button
charge
charge indicator
ringer button
Back Side
flash button
format/
conference
button
# pause button
7
BEFORE YOU BEGIN
PARTS CHECKLIST
Make sure your package includes the items shown here.
a
s
l
h
f
g
n
v
i
e
r
m
r
r
o
e
a
d
f
r
t
i
a
l
c
v
o
n
f
.
CID
def
abc
1
3
2
v
mno
ghi
jkl
4
6
5
volume
v
wxyz
pqrs
tuv
7
9
8
pause
charge
tone
oper
#
0
*
k
page/int.
c
a
b
l
l
a
c
speaker
e
r
e
n
f
c
n
e
o
c
e
r
e
n
f
c
n
e
v
o
c
c
a
l
l
v
b
format
a
c
a
l
c
l
b
k
format
a
c
k
l
o
v
/
l
TALK
o
d
v
i
/
TALK
c
d
v
i
c
v
r
e
d
i
a
l
r
e
d
i
a
l
i
n
1
ghi
4
pqrs
7
tone
*
flash
ringerpage
flash
ringerpage
i
n
t
t
def
abc
1
3
def
2
abc
3
2
mno
ghi
jkl
4
6
mno
5
jkl
6
5
wxyz
pqrs
tuv
7
9
wxyz
8
tuv
9
8
pause
tone
oper
#
pause
0
*
oper
#
0
Base
Telephone line cor d
Mounting pedestal
AC power supply
Dual Handsets
Belt clip
charge
Handset charge cradle
TELEPHONE JACK REQUIREMENTS
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a
modular jack, call your local phone company to find out
how to get one installed.
Handset batteries
Wall plate
Modular
telephone
line jack
8
IMPORTANT INSTALLATION INFORMATION
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
•Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
IMPORTANT INSTALLATION GUIDELINES
• Install telephone near both a telephone (modular) jack and an electrical
power outlet.
•Avoid sources of noise, such as a window by a busy street, and electrical
noise, such motors, microwave ovens, and fluorescent lighting.
•Avoid heat sources, such as heating air ducts, heating appliances,
radiators, and direct sunlight.
•Avoid areas of excessive moisture or extremely low temperature.
•Avoid dusty locations.
•Avoid other cordless telephones or personal computers.
9
INSTALLING THE PHONE
Choose the best location to install your base and handset charge cradle.
Your base and handset charge cradle should be placed on a level surface
such as a desk or table top, or you may mount the base on a wall.
charge
CONNECTING THE AC (ELECTRICAL) POWER
1. Plug the power supply cord into the power jack on the back of the
base and the other end into an electrical outlet. When the handset is
placed on the cradle the charge indicator turns on to indicate the
battery is charging.
CAUTION: Use only the ATLINKS USA, Inc. power supply 5-2562 that
came with this unit. Using other power supplies may damage the unit.
2. Plug the handset charge cradle into an electrical outlet.
CONNECTING THE TELEPHONE LINE
On the base, plug the one end of the telephone line cord into the jack on
the back of the base and the other end into a modular phone jack.
10
INSTALLING THE HANDSET BATTERY
NOTE: You must connect the handset battery before use.
1. Push down on the top of the battery compartment cover (located on the
back of each handset) and remove the cover.
2. Lift the battery pack and connect it's plug to the jack inside the
compartment.
NOTE: It is important to maintain the polarity (black and red wires) to the
jack inside the compartment as shown in the illustration.
3. Close the battery compartment by pushing the cover up until it snaps
into place.
4. Place the handsets in the charging cradles.
Allow handsets to charge for 12 hours prior to first use. If you don’t
properly charge the handsets, battery performance is compromised.
BATTERY
BLACK WIRE
PRESS DOWN
FIRMLY
RED WIRE
11
WALL MOUNTING THE BASE
NOTE: For best results, leave the phone on a flat surface during initial
charging before you hang the phone on the wall.
1. Turn the base over.
2. Attach the wall mounting pedestal by first inserting the tabs on the open
edge of the pedestal into the slots on the lower portion of the bottom of
the base. Then push down and snap the pedestal into place.
3. Slip the mounting holes (on the back of the pedestal) over the wall plate
posts and slide the unit down into place. (Wall plate not included.)
TELEPHONE SETUP
PROGRAMMABLE FUNCTIONS
This system uses a menu structure and soft key function buttons to give
you access to all of the built-in features.
USING THE SOFT KEYS
There are three buttons under the display box which represent several soft
key (programmable) functions. Use the buttons to activate the soft key
icons that appear in the display box. You may program the following items
with the soft keys: Language, Display Contrast, Area Code, Ringer Tone,
Time, Tone/Pulse, Registration, Deregistration, Walkie-Talkie, and Default
Setting.
LANGUAGE
This setting may be made with the handset or the base.
1. Make sure your phone is OFF (not in talk mode).
2. Press the MENU soft key to go to the main menu.
LANGUAGE
AREA CODE
OK
12
EXIT
3. Press cid/vol (up and down arrow) button on the handset or the CID (up
and down arrow) button on the base to scroll to
4. Press the OK soft key and
the display.
5. Use the touch tone pad on your handset to select
or use the cid/vol (up or down arrow) button on the handset or the CID
(up or down arrow) button on the base to move the arrow to your
selection. English is the default setting.
SET LANGUAGE 1ENG 2 FRA 3ESP
LANGUAGE
1ENG, 2FRA
.
shows in
, or
3ESP
,
SET LANGUAGE
1 ENG 2 FRA 3 ESP
OK
6. Press the OK soft key to save your selection, and return to the main
menu. The selected language displays for two seconds.
EXIT
ENGLISH
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu.
LANGUAGE
CONTRAST
OK EXIT
BASE DISPLAY HANDSET DISPLAY
LANGUAGE
AREA CODE
OK EXIT
DISPLAY CONTRAST
This setting may be made with the base only.
13
1. Make sure your base is at the main menu. If your base is not in the
menu mode, press the MENU soft key.
2. Press the CID (up or down arrow) button to scroll to
CONTRAST
.
LANGUAGE
CONTRAST
OK
EXIT
3. Press the OK soft key and
4. Use the touch tone pad on your base to select 1, 2, or 3, or use the CID
(up or down arrow) button to move the arrow to your selection. Contrast
level 1 is the default setting.
SET CONTRAST 1 2 3
shows in the display.
SET CONTRAST
1 2 3
OK
5. Press the OK soft key to save your selection and return to the main
menu. The selected contrast level displays for two seconds.
EXIT
CONTRAST - 2
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu screen.
LANGUAGE
CONTRAST
OK
EXIT
14
AREA CODE
If you enter a 3-digit area code in the area code menu, your local area code
will not appear in Caller ID messages you receive. Instead, you will see
only the local seven digit number. Calls you receive from outside your
local area code will show the full ten-digit number.
This setting may be made with the handset or the base.
1. Make sure your handset or base is at the main menu. If your handset or
base is not in the menu mode, press the MENU soft key.
2. Press the cid/vol (up or down arrow) button on the handset or the CID
(up and down arrow) button on the base to scroll to
AREA CODE
.
LANGUAGE
AREA CODE
OK
HANDSET DISPLAY BASE DISPLAY
3. Press the OK soft key and
is the default setting.
EXIT
SET AREA CODE
AREA CODE
RINGER TONE
OK
- - - shows in the display. - - -
EXIT
SET AREA CODE
- - -
OK
4. Use the touch tone pad on your base or handset to enter your three digit
area code.
5. Press the OK soft key to save your selection and return to the main
menu. The selected area code displays for two seconds.
EXIT
AREA CODE - 317
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu.
15
LANGUAGE
AREA CODE
OK EXIT
HANDSET DISPLAY BASE DISPLAY
AREA CODE
RINGER TONE
OK
EXIT
RINGER TONE
This setting may be made with the handset or the base. You may choose
from six different ringer tones.
1. Make sure your handset or base is in the menu mode. If your handset or
base is not in the menu mode, press the MENU soft key.
2. Press the cid/vol (up or down arrow) button on the handset or the CID
(up and down arrow) button on the base to scroll to
RINGER TONE
.
RINGER TONE
REGISTRATION
OK EXIT
HANDSET DISPLAY BASE DISPLAY
3. Press the OK soft key and
display.
4. Use the touch tone pad on your handset or base to select
the cid/vol (up or down arrow) but ton on the handset or the CID (up or down
arrow) button on the base to mo ve the ar row to your selection. The default
setting is 1.
SET RINGER TONE 1 2 3 4 5 6
AREA CODE
RINGER TONE
OK
1, 2, 3, 4, 5, 6 ,
EXIT
shows in the
or use
SET RINGER TONE
1 2 3 4 5 6
OK
NOTE: When you use the handset or base to set a ringer tone, the ringer tone
plays after you make your selection.
16
EXIT
5. Press the OK soft key to save your selection, and return to the main
menu. The new ringer tone is displayed for two seconds.
RINGER TONE - 2
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu screen.
RINGER TONE
REGISTRATION
OK
HANDSET DISPLAY BASE DISPLAY
EXIT
AREA CODE
RINGER TONE
OK
EXIT
TONE/PULSE
Most telephone systems use tone dialing, however, some may still use
pulse dialing. Depending on your telephone system, set the dialing mode
as follows:
This setting may be made with the base only.
1. Make sure your base is in the menu mode. If your base is not in the
menu mode, press the MENU soft key.
2. Press the CID (up or down arrow) button on the base to scroll to
TONE/PULSE
.
TONE / PULSE
TIME
3. Press the OK soft key and
the display.
OK
SET TONE/PULSE 1TONE 2PULSE
EXIT
shows in
SET TONE / PULSE
1 TONE 2 PULSE
OK
EXIT
17
4. Use the touch tone pad on the base to select
the CID (up or down arrow) button to move the arrow to your selection.
The default setting is 1.
5. Press the OK soft key to save your selection, and return to the main
menu. The dialing mode displays for two seconds.
1TONE
or
2PULSE
, or press
TONE
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu screen.
TONE / PULSE
TIME
OK
NOTE: If you aren’t sure which dialing system you have, set the telephone to
tone dialing and make a test call. If the call connects, the setting is correct. If
the call does not connect, set the telephone to pulse dialing.
EXIT
HANDSET REGISTRATION
This setting may be made with the handset only. During the registration
process, keep your handset near the base. Make sure your handset is at
the main menu. Make sure your phone is OFF (not in talk mode).
1. Make sure your handset is at the main menu. If your handset is not in
the menu mode, press the MENU soft key.
2. Press the cid/vol (up or down arrow) button to scroll to
REGISTRATION
.
RINGER TONE
REGISTRATION
3. Press the OK soft key and
18
OK
REGISTER HANDSET?
EXIT
shows in the display.
4. Press the OK soft key and
the display.
HANDSET NEEDS REGISTRATION
shows in
HANDSET NEEDS
REGISTRATION
OK
5. Press the OK soft key and
the display.
EXIT
HOLD, BASE PAGE WAIT FOR BEEP
REGISTER
HANDSET ?
OK
EXIT
shows in
HOLD BASE PAGE
WAIT FOR BEEP
EXIT
6. Press and hold the page/int button on the base until you hear a long
beep and the handset displays
CONFIRM REGISTRATION?
CONFIRM
REGISTRATION ?
OK EXIT
7. Press the OK soft key on the handset to confirm the registration.
HANDSET # REGISTERED
registration is complete, you may name the handset.
shows in the display.
displays for two seconds. When handset
ENTER NAME
HANDSET 2
REGISTERED
ENTER NAME
OK EXITDEL
19
BILL SMITH
HANDSET 2
MENU DIR
8. Use the touch tone pad to enter the name.
More than one letter is stored in each of the number keys. For example,
to enter the name Bill Smith, press the 2 key twice for the letter B.
Briefly pause and the cursor moves to the next field. Press the 4 key 3
times for the letter I. Briefly pause and the cursor moves to the next
field. Press the 5 key 3 times for the letter L. Briefly pause and the cursor
moves to the next field. Press the 5 key 3 times for the second letter L,
press 1 key to add a space. Press the 7 key 4 times for the letter S.
Briefly pause and the cursor moves to the next field. Press the 6 key
once for the letter M. Briefly pause and the cursor moves to the next
field. Press the 4 key 3 times for the letter I. Briefly pause and the cursor
moves to the next field. Press the 8 key for the letter T. Briefly pause and
the cursor moves to the next field. Press the 4 key twice for the letter H.
ENTER NAME
B
OK EXITDEL
ENTER NAME
BILL SMITH
OK EXITDEL
NOTE: If you make a mistake press the DEL soft key to backspace and erase
the wrong character(s).
9. Press the OK soft key to save the name and return to the main menu.
You will hear a confirmation tone.
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu. Or press and hold the EXIT soft key on the handset to return
to standby mode.
20
HANDSET DE-REGISTRATION
This setting may be made with the handset only. Deregistration cancels a
handset’s registration. If you do not know a handset’s name, you should
deregister the handset according to the steps below. During the deregistration process, keep the handset near the base.
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that handset's
telephone features cannot be used until the handset is re-registered.
1. Make sure your handset is in menu mode. If your handset is not in the
menu mode, press the MENU soft key.
2. Press the cid/vol (up or down arrow) button to move the arrow to
DEREGISTRATION
.
DEREGISTRATION
WALKIE TALKIE
OK EXIT
3. Press the OK soft key and
display.
DE-REGISTER HANDSET?
shows in the
DE - REGISTER
HANDSET 1 ?
OK EXIT
4. Press the OK soft key to de-register the handset, and
BASE
displays until the handset is moved closer to the base.
MOVE NEAR TO
MOVE NEAR
TO BASE
EXIT
21
Then the handset displays
CONFIRM DEREGISTRATION?
CONFIRM
DEREGISTRATION ?
OK
EXIT
5. Press the OK soft key to confirm the deregistration.
DEREGISTERED
followed by
REGISTER HANDSET?
HANDSET #
shows in the display.
HANDSET 1
DEREGISTERED
NOTE: Press the EXIT soft key once to keep the previous setting and return to
the main menu screen.
GLOBAL DEREGISTRATION
If one or more handsets becomes lost, you should de-register all handsets
to ensure proper system operation. Follow the steps below to deregister
both handsets at the same time.
WARNING: It is not recommended that a handset be de-registered unless
absolutely necessary because once a handset is de-registered, that handset's
telephone features cannot be used until the handset is re-registered.
1. Press and hold the base page/int button on the base until the charge
indicator flashes.
2. Press and hold the base page/int button again until the charge indicator
flashes rapidly.
3. Press and release the page/int button on the base. The charge indicator
stops blinking, and the base display shows
DEREGISTERED
registered. Then the base returns to standby mode, and each handset
displays
REGISTER HANDSET?
for five seconds to confirm that all handsets are de-
ALL HANDSET
22
WALKIE TALKIE
This feature allows a pair of handsets to be used like walkie talkies
(electrical power to the base unit is not required for walkie talkie
operation). This setting may be made with the handset only.
1. Make sure your handset is at the main menu. If your handset is not in
the main menu, press the MENU soft key.
2. Press the cid/vol (up or down arrow) button to move the arrow to
WALKIE T ALKIE
.
DEREGISTRATION
WALKIE TALKIE
OK EXIT
3. Press the OK soft key and
display.
WALKIE T ALKIE ENABLE?
shows in the
WALKIE TALKIE
ENABLE ?
OK EXIT
4. Press the OK soft key and
TALKIE HANDSET# shows
WALKIE TALKIE ENABLED
in the display.
followed by
WALKIE
WALKIE TALKIE
ENABLED
NOTE: Both handsets must be in walkie talkie mode to send and receive.
5. Press the page/int button, and then enter the handset number/extension
you want to call. The selected handset is paged. When the page/int
button on the receiving handset is pressed, and the page is answered,
the walkie talkie feature is activated between both handsets. Both
handsets display
WALKIE TALKIE WITH HANDSET #
WALKIE TALKIE
HANDSET 1
.
EXIT
23
WALKIE TALKIE
HANDSET #
EXIT
WALKIE TALKIE
EXTENSION ?
EXIT
PAGING
HANDSET #
EXIT
WALKIE TALKIE
WITH HANDSET #
MUTE
6. When your conversation is finished, both the sending and recei ving
handsets may press the EXIT soft key to disable the walkie talkie feature
and return to the walkie talkie standby mode.
EXIT
WALKIE TALKIE
HANDSET #
WALKIE TALKIE
DISABLED
EXIT
7. Press EXIT key again will disable the walkie talkie and go back to
handset standby mode.
display.
NOTE: When two handsets are in walkie talkie mode, they are isolated from
the base and cannot receive pages or dial out until the walkie talkie is disabled.
WALKIE T ALKIE DISABLED
shows briefly in the
NAME
HANDSET 1
MENU
24
DIR
TIME OF DAY
This setting may be made with the base only.
1. Make sure your base is in the menu mode. If your base is not in the
menu mode, press the MENU soft key.
2. Press the CID (up or down arrow) to scroll to
TIME
.
TONE/PULSE
TIME
OK
EXIT
3. Press the OK soft key and
SET TIME - - : - - AM PM
shows in the display.
SET TIME
_ _ : _ _ AM PM
OK
4. Use the touch tone pad to enter the current time. The arrow
automatically moves to the AM field. Press the CID (up or down arrow)
button to move the arrow to
PM.
The default setting is
EXIT
12:00 AM
.
12;34 PM
5. Press the OK soft key to save your selection and return to the main
menu. The current time displays for two seconds.
TONE/PULSE
TIME
OK
EXIT
25
DEFAULT
As you become familiar with this system, you may prefer to use the
system’s original settings. Follow the steps below to return to the factory
default settings.
1. Make sure your handset or base is in menu mode. If your handset or
base is not in the menu mode, press the MENU soft key.
2. Press the cid/vol (up and down arrow) button on the handset or CID (up and
down arrow) button on the base to move the arrow to
DEFAULT SETTING
.
DEFAULT SETTING
LANGUAGE
OK
EXIT
3. Use the touch tone pad on your handset or base to enter
or use the cid/vol (up or down arrow) button on your handset or the CID
(up or down arrow) button on your base to move the arrow to your
selection.
2NO
is the default setting.
1YES
or
2NO
,
DEFAULT SETTING
1 YES 2NO
OK
NOTE: If you choose YES all settings in the programmable menu return to the
factory default settings.
4. Press the OK soft key to save your selection, and return to the main
menu. The default setting you choose shows on the display for two
seconds.
DEFAULT SETTING
NO
HANDSET & BASE DISPLAY HANDSET & BASE DISPLAY
26
EXIT
DEFAULT SETTING
LANGUAGE
OK
EXIT
NOTE: Press the EXIT soft key once to keep the previous setting and return
to the main menu.
BASIC OPERATION
SPEAKERPHONE
For hands-free operation and convenience, your dual-handset system is
equipped with a speakerphone.
For best speakerphone performance, avoid the following:
• Areas with high background noise. (The microphone might pick up
these sounds.)
• Surfaces affected by vibration.
•Recessed areas such as in a corner, under a cupboard, or next to a
cabinet, which can generate an echo effect.
Note the following guidelines when using the speakerphone:
• The speakerphone works similar to a two-way radio. You can only listen
or talk at one time.
• Stay reasonably close to the phone so that you can be clearly heard by
the person to whom you are talking.
NOTE: Only one-way conversation is possible in speakerphone mode. When
you are speaking, you are transmitting. When you are listening, you are
receiving. You can’t do both at the same time. The phone automatically
switches between transmitting and receiving depending on the level of the
voice or the room noise detected by the speakerphone microphone.
CHARGE INDICATOR
When the charge indicator is lit, the handset is correctly seated in the
cradle and is charging. The indicator flashes when the base is paged, when
the base pages the handset, or when you receive an incoming call.
27
MAKING A CALL
HANDSET
1. Pick up the handset and press the talk/callback button on the handset.
Listen for a dial tone.
2. Dial the desired number, or dial the number first then press the talk/
callback button.
3. When finished, press the talk/callback button again to hang up.
SPEAKERPHONE
1. Press the callback/speaker button on the base. You will hear a dial tone.
2. Dial the number you wish to call. Or, you can dial the number and then
press the speaker/callback button.
3. When finished, press the callback/speaker button to hang up.
ANSWERING A CALL
HANDSET
1. When the phone rings, press the talk/callback button on the handset.
2. When finished, press the talk/callback button again to hang up.
SPEAKERPHONE
1. When the phone rings, press the speaker/callback button to answer a call.
2. When finished press callback/speaker to hang up.
NOTE: If you are using the handset and want to switch to the speakerphone,
press the callback/speaker button. The speakerphone indicator turns on. To
continue using the handset, press the talk/callback button.
28
CALL TIMER
After you press talk/callback on the handset or speaker/callback on the
base, the built-in call timer shows in the display and counts the length of
time of the call in minutes and seconds.
AUTO STANDBY
Placing the handset in the base cradle or handset charge cradle while the
handset is off the hook (during a call) automatically hangs up the handset.
RINGER VOLUME SWITCH
HANDSET
1. Press the ringer button and the current ringer setting shows in the display.
RINGER ON
1 ON 2 OFF
OK
EXIT
2. Use the touch tone pad on your handset to enter
the cid/vol (up and down arrow) to scroll to your selection.
3. Press the OK soft key to save your selection, and you will hear a
confirmation tone and the ringer setting displays for two seconds.
1 ON
or
2 OFF,
or use
RINGER ON
NOTE: If you turn the ringer OFF, the ringer off icon shows in the display.
NAME
HANDSET 1
MENU
DIR
29
BASE
1. Press the ringer button and the current ringer setting shows in the display.
RINGER HIGH
1 HI 2 LOW 3 OFF
OK
EXIT
2. Use the touch tone pad on your handset to enter
use the CID (up and down arrow) to scroll to your selection.
3. Press the OK soft key to save your selection, and the ringer setting
shows in the display for two seconds then returns to standby mode.
1HI, 2LOW
, or
3OFF
, or
RINGER LOW
01:15 PM
NEW CALL 00
MENU
DIR
FLASH/CALL WAITING
If you subscribe to the combined Call Waiting Caller ID service from your local
telephone company, you will receive Caller ID information (if available) on Call
Waiting calls. During a phone call you will hear a beep, which indicates
another call is waiting on the line, and Caller ID information shows in the
handset display. To connect to the waiting call, press the flash button on the
handset and your original call is put on hold. You may switch back and forth
between the two calls by pressing the flash button.
TIP: Don’t press the talk/callback button on the handset or the speaker/
callback button on the base to activate a custom calling service, such as call
waiting, or you’ll hang up the phone.
30
LAST NUMBER REDIAL
To quickly redial the last number you dialed:
1. Press the talk/callback button on the handset or the speaker/callback
button on the base.
2. Press the redial button.
-OR-
3. Press the redial button first then press the talk/callback button or the
speaker/callback button. If you get a busy signal and want to keep
dialing the number, press the redial button to quickly redial the number.
HOLD
Press the HOLD soft key on the handset or base to put a call on hold.
ON HOLD
shows in the handset display.
LINE
LINE ON HOLD
TALK 00:10 VOL 2
CONF
Your phone stays on hold until you press the EXIT soft key and release the
line, or press the talk/callback button to return to standby mode. If you
continue the call on a separate extension phone, or other registered
handset your cordless phone releases the line to the extension phone.
If the handset with the call on hold is placed back on the cradle, the holding
call is transferred to the base speakerphone and the handset returns to
standby mode.
TRANS
EXIT
EXIT
Press the EXIT soft key to end an operation, such as HOLD or
TRANSFER. The display shows
returns to the TALK mode.
LINE ACTIVE
for two seconds then
31
LINE ACTIVE
TALK 00:05 VOL 2
MUTE
HOLD
DIR
PAGING THE HANDSET
This feature helps you locate a misplaced handset. To send and receive
pages, all handsets must be registered. If your handsets are not registered
follow the instructions in the Handset Registration section of this manual.
PAGING FROM THE BASE OR HANDSET
Make sure the phone is OFF (not in talk mode).
1. Press the page/int button the handset or base.
PAGING
EXTENSION ?
EXIT
2. Use the touch tone pad on your handset or base to select 1 or 2.
EXTENSION
NOTE: Press the * key to page all registered handsets or press the 0 key to
page the base.
3. The receiving handset or base starts paging.
shows in the display.
PAGING
32
PAGING
HANDSET 2
EXIT
SENDING HANDSET
PAGING FROM
HANDSET 1
RECEIVING HANDSET
When the talk/callback or speaker/callback or page/int on the receiving
handset or base is pressed the page is answered. If the page is not answered
after two minutes,
base and the page is cancelled. The unit returns to standby mode.
NOTE: If name has been assigned to the handset during registration, then the
name will be displayed instead of handset number when paging starts.
NOTE: To cancel the page, press the EXIT soft key or the page/int button.
TRANSFERRING CALLS
This feature lets you transfer calls between handsets or the base in talk
mode.
1. Press the HOLD soft key to put the call on hold.
NO ANSWER
shows in the display of sending handsets or
TALK 00:10 VOL 2
2. Press the TRANS soft key.
TALK 00:10 VOL 2
LINE ON HOLD
EXTENSION ?
MUTE DIR
HOLD
LINE ON HOLD
CONF
TRANS
EXIT
EXIT
33
3. Enter the handset number you want to transfer the call to, and the
receiving handset is paged.
PAGING FROM
HANDSET 2
RECEIVING HANDSET
PAGING/LINE ON HOLD
STEVE
EXIT
SENDING HANDSET
NOTE: If the page isn’t answered, press the EXIT soft key or the page/int
button to cancel the transfer.
When the page/int or talk/callback button is pressed on the receiving
handset, the unit goes into intercom mode. When the talk/callback button
on the sending handset is pressed, the call is transferred.
After you select the station you want to transfer the call to, press the talk/
callback button to hang up your station. If the other station does not take
the call within 30 seconds, the call is transferred back to your station.
MUTE
To have a private, off-line conversation use the mute feature. The party on
the other end of the line cannot hear you, but you can still hear them.
1. While having a phone conversation you may press the MUTE soft key.
MUTE ON
shows in the display.
MUTE ON
TALK 00:10 VOL 2
MUTE DIR
HOLD
34
2. Press the MUTE soft key to cancel mute and return to your phone
conversation.
TALK 00:05 VOL 2
MUTE DIR
HOLD
TEMPORARY TONE DIALING
This feature is useful only if you use pulse dialing service. Temporary tone
dialing enables pulse (rotary) service phone users to access touch-tone
services offered by banks, credit card companies, etc. For example, when
you call your bank you may need to enter your account number. Using the
temporary tone feature allows you to temporarily switch to touch tone
mode so you can enter and send your number.
1. Dial the telephone number and wait for the line to connect.
2. When your call is answered, press the *tone button on your handset
number pad to temporarily change from pulse dialing to tone dialing.
3. Follow the automated instructions to get the information you need.
4. Hang up the handset and the phone automatically returns to pulse
(rotary) dialing mode.
CORDLESS HANDSET VOLUME CONTROL
When the cordless handset is ON (in talk mode) adjust the receiver volume
by pressing the cid/vol (up or down arrow) button on the cordless handset.
There are four volume levels, and each press of the cid/vol (up or down)
button adjusts the receiver volume by one level.
SPEAKERPHONE VOLUME CONTROL
When the speakerphone is ON, adjust the volume by pressing the volume
up or down arrow buttons on the base. When the maximum or minimum
volume level is reached the phone beeps twice.
NOTE: You may also adjust the volume during walkie talkie mode, intercom
mode, and conference mode.
35
INTERCOM
The intercom feature allows you to have an unlimited-duration, two-way
conversation between two handsets or the base and a handset.
MAKING AN INTERCOM CALL
1. Make sure the phone is OFF (not in talk mode).
2. Press the page/int button on the handset or base.
shows in the display.
PAGING EXTENSION
PAGING
EXTENSION ?
EXIT
3. Enter the desired handset number or base (enter 0) you want to
intercom with. The receiving party is paged.
NOTE: To cancel the page, press the page/int button or the EXIT button.
HANDSET 1
PAGING
EXIT
THE SENDING PARTY THE RECEIVING PARTY
4. Wait for the receiving party to answer and activate the intercom feature.
The following displays when the intercom is setup:
INTERCOM
HANDSET 1
MUTE
5. When finished, press the EXIT soft key or the page/int button on either
handset to deactivate the intercom.
36
EXIT
PAGING FROM
HANDSET 2
INTERCOM
HANDSET 2
MUTE
EXIT
NOTE : During the intercom, if a handset is assigned a name, that name is
displayed instead of handset number.
RECEIVING AN INTERCOM CALL
When an intercom call is received, the handset or base beeps. To answer
the intercom call, press the page/int button.
RECEIVING AN EXTERNAL TELEPHONE CALL DURING AN INTERCOM CALL
BETWEEN HANDSETS
If you receive a telephone call during an intercom call, both users are
alerted with a ringing tone. Press the talk/callback button on the handset to
end the intercom. Press the talk/callback button again to take the external
telephone call.
BETWEEN BASE AND HANDSET
If you receive a telephone call during an intercom call, the intercom
between the handset and the base automatically ends and the unit rings.
Press the talk/callback on the handset or the speaker/callback button on the
base to take the external telephone call.
USING INTERCOM OR CONFERENCE WITH EXTERNAL CALLS
During an external telephone call, you may page other handsets and have offline, private intercom conversations between an external caller and the
handsets, or you may have a 3-way conference with external line and another
handset or the base.
1. During an external call, press the HOLD soft key on the handset to place
the external call on hold.
or base display.
LINE ON HOLD
shows in the sending handset
LINE ON HOLD
TALK 00:10 VOL 2
CONF
TRANS
EXIT
37
2. Press the CONF soft key on your handset or base.
EXTENSION?
shows in the display.
LINE ON HOLD
LINE ON HOLD
EXTENSION ?
EXIT
3. Enter the desired handset number to select the base or the handset
number you want to conference with. The receiving party is paged.
PAGING/LINE ON HOLD
HANDSET 2
PAGING FROM
HANDSET 1
EXIT
SENDING HANDSET RECEIVING HANDSET
4. The recei ving handset or base must press the page/int button to answer
the intercom, then both intercom users may speak privately. The
external caller cannot hear the intercom conversation.
LINE ON HOLD/INTERCOM
HANDSET 2
MUTE
SENDING HANDSET RECEIVING HANDSET
5. Either sending or receiving party may press the format/conference
button to start the 3-way conference.
NOTE: Press the EXIT soft key on either handset to cancel the intercom call
and let the sending party continue to talk to the external party. Or the calling
party may press the talk/callback button to transfer the call to the receiving
party who may speak to the external caller independently.
NOTE: A handset or the base can enter conference directly by pressing talk/
callback on the base while the other handset or the base is on an external call.
EXIT
HANDSET 1
MUTE
INTERCOM
EXIT
38
MEMORY
The handset and base each have their own separate memory dialing
storage areas. Fifty 15-character names and 24-digit telephone numbers
can be stored in the handset memory. Fifty 15-character names and 24digit telephone numbers can be stored in the base memory.
STORING A NAME AND NUMBER IN MEMORY
1. Make sure the phone is OFF (not in talk mode).
2. Press the DIR soft key.
NAME
HANDSET 1
MENU DIR
3. Press the desired memory location button (01 through 50) or, use the cid/
vol (up or down arrow) button on handset or CID up or down arrow on the
base to select the memory location. If the memory location is occupied, the
memory location and stored name and number appear in the display. If the
memory location is empty,
EMPTY
shows in the display.
#
MEMO
--
SELECT MEMORY
01-50
EXIT
#
0 3
MEMO
* * EMPTY * *
EDIT
4. Press the EDIT soft key. The display shows
DEL
EXIT
ENTER NAME
#
0 3
MEMO
ENTER NAME
OK DEL
EXIT
.
39
5. Use the touch tone pad on your handset or base to enter a name (up to
15 characters). More than one letter is stored in each of the number
keys. For example, to enter Bill Smith, press the 2 key twice for the letter
B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the
letter L. Wait for 1 second. Press the 5 key 3 times for the second letter L,
and press the 1 key to insert a space between the first and last name.
Press the 7 key 4 times for the letter S; press the 6 key once for the letter
M; press the 4 key 3 times for the letter I; press the 8 key for the letter T;
press the 4 key twice for the letter H.
6. Press the OK soft key to confirm your selection. The display shows
ENTER TEL NUMBR
.
#
0 3
MEMO
ENTER TEL NUMBR
OK DEL
7. Use the touch tone pad on your handset or base to enter the area code
followed by the telephone number (up to 24 digits, including pauses)
and press the OK soft key again to save your selection. The unit beeps to
confirm.
EXIT
NAME
HANDSET 1
MENU
8. To enter another name and number in a different memory location,
please follow step 1 and repeat the process.
40
DIR
STORING A REDIAL NUMBER
1. Make sure the phone is OFF (not in talk mode).
2. Press the DIR soft key.
3. Press any number key (01-50) to store the phone number in that
memory location, or press the cid/vol (up and down arrow) button on
the handset or CID (up and down arrow) button on the base to select the
memory location.
4. Press the EDIT soft key and
5. Use the touch tone pad on your handset or base to enter the name, then
press the OK soft key and
6. Press the redial button to display the redial number.
7. Press the OK soft key again to confirm.
NOTE: If the redial number has more than an 24 digits, the redial number
cannot be stored in memory.
ENTER NAME
ENTER TEL NUMBR
shows in the display.
shows in the display.
INSERTING A PAUSE IN THE DIALING SEQUENCE
If a pause is needed to wait for a dial tone press the # pause button on
the number pad to insert a delay in dialing sequence of a stored
telephone number (for example, after you dial 9 for an outside line, or
wait for a computer access tone.) Each pause counts as one digit in the
dialing sequence.
REVIEWING, CHANGING OR DELETING STORED NUMBERS
TO REVIEW:
1. Make sure the phone is OFF (not in talk mode).
2. Press DIR soft key.
NAME
HANDSET 1
MENU
DIR
41
3. Press the cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base to scroll through the stored numbers.
Or use the touch tone pad on your handset or base to enter the memory
location number.
#
0 3
MEMO
317 - 123 - 4567
PETER CHAN
EDIT
DEL
EXIT
TO CHANGE:
Use the same procedure to change a stored number as you do to store a
number - instead just replace one stored phone number with a different one.
TO DELETE:
1. Make sure the phone is OFF (not in talk mode).
2. Press DIR soft key
3. Press the cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base to scroll to a desired record.
4. When the record shows in the display, press the DEL soft key to mark
the record for deletion. The display shows
DELETE?
#
0 3
MEMO
317 - 123 - 4567
DELETE ?
OK
EXIT
5. Press the OK soft key a second time to delete the record. The display
shows
DELETED
for two seconds. You will hear a confirmation tone.
* * DELETED * *
42
NOTE: If you don’t want to change or delete a number, simply press EXIT
soft key, or wait for one minute to exit the review mode.
DIALING A STORED NUMBER
HANDSET
Make sure the phone is ON by pressing the talk/callback button.
1. Press the DIR soft key.
2. Enter the memory location number (01-50) for the desired memory
location. The number will be dialed automatically.
-OR-
1. Make sure the phone is OFF (not in talk mode).
2. Press the DIR soft key.
3. Press the number key (01-50) for the desired memory location or use the
cid/vol (up or down arrow) button to scroll through memory until the
desired number displays.
4. Press the talk/callback button. The number dials automatically.
BASE
Make sure the phone is ON by pressing the pressing the speaker/callback
button.
1. Press the DIR soft key.
2. Press the number key (01-50) for the desired memory location. The
number dials automatically.
-OR-
Make sure the phone is OFF (not in talk mode)
1. Press the DIR soft key.
2. Press the number key (01-50) for the desired memory location, or use
the CID (up or down arrow) button to scroll through memory until the
desired number displays.
3. Press the speaker/callback button. The number dials automatically.
43
CHAIN DIALING FROM MEMORY
Use this feature to make calls that require a sequence of numbers, such as
a calling card number used for a frequently called long distance number.
The following example shows how you can store each part of the long
dialing sequence and use chain dialing to make a call through a long
distance service:
1. Make sure the phone is ON .
The Number For Memory Location
Long Distance Access Number 7
Authorization Code 8
Frequently called long distance number 9
2. Press DIR soft key and then press 07.
3. When you hear the access tone, press DIR soft key, and then press 08.
4. At the next access tone, press DIR soft key then press 09.
CALLER ID (CID)
Caller ID (CID) is a service available from your local telephone company.
For Caller ID to work on this system, you must subscribe to Caller ID
service. To receive Caller ID information for a Call Waiting call, you must
subscribe to the combined Call Waiting Caller ID service.
44
18:88
AM
88 88 88 88
PM
NEW
REPT
CALL
MEMO
000000000000000
000000000000000
000000000000000
#
When your telephone rings, and you are subscribed to Caller ID Call
Waiting service, you will receive information (if available) transmitted by
your local telephone company. You will also receive Caller ID information
from Call Waiting calls. If you receive an incoming call and you are already
on the phone, a beep indicates the presence of a Call Waiting Call on the
line, and Caller ID information for the Call Waiting call shows on the
display. This information may include the phone number, date and time; or
the name, phone number, and date and time.
RECEIVING AND STORING CALL RECORDS
When you receive a call, Caller ID information is transmitted by the phone
company to your Caller ID telephone between the first and second ring.
The Caller ID information appears on the display while the phone rings,
giving you a chance to monitor the information and decide whether or not
to answer the call.
If you are not at home or cannot answer, your telephone’s Caller ID
memory automatically stores the call number, date, time, phone number,
and name for the 40 most recent calls received so you can see who called
while you were unavailable. Caller ID records are stored sequentially, in
the order they are received. When the 41st call is received, the oldest
Caller ID record is automatically deleted.
You may review the stored information for the most recent 40 calls at any
time. Calls received since your last review show as
NEW
in the display.
REVIEWING CALL RECORDS
As calls are received and stored, the display is updated to let you know
how many calls have been received.
1. Press the cid/vol (up arrow) button to review oldest call and scroll toward
the most recent calls (higher numbers). When you reach the newest call,
the display shows
END OF LIST
.
45
2. Press the cid/vol down arrow button on the handset or CID (down arrow)
button on the base to review the newest call and scroll to older calls (lower
numbers). When you reach the oldest call, the display shows
END OF LIST
.
As you review calls, the display shows you the following information for
each call:
• The telephone number of the caller.
• The number of the call, with regard to the order received.
• The name of the caller, if this service is available in your area.
NOTE: If a name is received which exceeds 15 characters, the extra characters
are removed.
•Time and date the call was received.
•
NEW
appears for all calls that have not been reviewed.
NOTE: Check with your local phone company regarding name service
availability.
TRANSFERRING CID RECORDS TO MEMORY
You may transfer a Caller ID record to your phone ’s memory.
NOTE: It is important that you format CID records correctly before storing in
memory. It is not possible to reformat CID records stored in memory.
1. Use the cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base to scroll to the desired CID record.
2. Press the SAVE soft key.
46
9:58AM 11/24
317 - 123 - 4567
PETER CHAN
SAVE
DEL
NEW
CALL
EXIT
#
01
3. Press the desired memory location button. Example, press the number
01 key to store the record in memory location 1. If the memory location
is occupied and, you want to replace it, you must confirm the
replacement by pressing the OK soft key.
#
--
MEMO
SELECT MEMORY
01-50
EXIT
#
01
MEMO
765-4321
REPLACE MEMO?
OK
NOTE: Press EXIT soft key once to keep previous the setting and return to the
Caller ID menu. Or, press and hold the EXIT soft key on handset to return to
standby mode.
EXIT
DIALING A CALLER ID NUMBER
While reviewing Caller ID records, you may call the caller phone number
showing in the display.
1. Make sure the phone is OFF (not in talk mode).
2. Press cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base until the desired call record is
displayed. Depending on (a) how the incoming phone number was
formatted when it was received, and (b) whether or not you previously
pre-programmed your local area code into memory, you may need to
adjust the format of the incoming caller ’s stored phone number before
dialing it back. The format button lets you change the format of the
displayed number.
47
Available formats include:
Number of digits Explanation Example
Eleven digits long distance code “1 ” 1-317-888-8888
+3- digit area code +7-digit
telephone number.
Ten digits 3-digit area code +7-digit 317-888-8888
telephone number.
Seven digits 7-digit telephone number. 888-8888
NOTE: If the phone company does not supply all ten digits of an incoming
number, you will not be allowed to adjust the format of that number.
3. If the number does not dial as shown, press the format/conference
button on handset or format/conf on the base. Repeat if necessary, until
the correct number of digits show in the display.
4. Press the talk/callback button on the handset or speaker/callback on the
base. The number dials automatically.
NOTE: If the number is corrupted, such as a number in a name or an
alphabetical character in a number, an error tone sounds from the handset or
base and the number cannot be dialed.
DELETING THE CALLER ID RECORD SHOWING IN THE DISPLAY
To delete only the record showing in the display:
1. Make sure the phone is OFF (not in talk mode).
NAME
HANDSET 1
MENU
48
DIR
2. Use the cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base to display the desired Caller ID record.
CALL
NEW
#
9:58AM 11/24
01
12 34567890 1 2 34 5
STEVE
SAVE
DEL
EXIT
3. Press DEL soft key. The display shows
DELETE CALL ID?
DELETE CALL ID?
OK
4. Press OK soft key to erase the record. The display shows
seconds, and confirms the deletion. You will hear a confirmation tone.
EXIT
DELETED
, for two
* *DELETED * *
NOTE: Press EXIT soft key once to return to the CID review menu. Or, press
and hold the EXIT soft key on the handset to return to standby mode.
DELETING ALL CALLER ID RECORDS
To delete all of the Caller ID records in memory:
1. Make sure the phone is OFF (not in talk mode).
NAME
HANDSET 1
MENU
DIR
49
2. Use the cid/vol (up or down arrow) button on the handset or CID (up or
down arrow) button on the base to display any Caller ID record.
CALL
NEW
#
9:58AM 11/24
01
12 34567890 1 2 34 5
NAME
SAVE
3. Press and hold the DEL soft key for two seconds. The display shows
DELETE ALL?
DEL
EXIT
DELETE ALL ?
OK
4. Press the OK soft key to erase all CID records from memory. The display
shows
NO CALLS
. You will hear a confirmation tone.
EXIT
NO CALLS
NOTE: Press the EXIT soft key once to return to the CID review menu. Or,
press and hold the EXIT soft key to return to standby mode.
CALLER ID ERRORS
If there is an error in the transmission of information to your Caller ID
phone,
subscribed to Caller ID service or it is not working properly,
shows in the display.
ERROR
or
INCOMPLETE DATA
shows in the display. If you are not
NO DATA
50
REPLACING THE BATTERY
CAUTION: To reduce the risk of fire or personal injury, use only the
battery 5-2459 that is compatible with this unit.
Make sure the telephone is OFF (not in talk mode)
before you replace battery.
1. Remove the battery compartment cover.
2. Disconnect the cord attached to the battery pack
from the jack inside the battery compartment and
remove the battery pack from the handset.
3. Insert the new battery pack and reconnect the
battery plug.
4. Put the battery compartment cover back on.
5. Place handset in the base to charge. If you don’t
charge the handset battery properly (for 12 hours)
when you first set up the phone and/or when you
install a new battery pack, the battery’s long-term
performance will be compromised.
BATTERY SAFETY PRECAUTIONS
• Do not burn, disassemble, mutilate, or puncture. Like other batteries of
this type, toxic materials could be released which can cause injury.
•Keep batteries out of the reach of children.
•Remove batteries if storing over 30 days.
NOTE: The RBRC seal on the battery used in your ATLINKS
USA, Inc. product indicates that we are participating in a
program to collect and recycle Nickel Cadmium batteries
throughout the United States. Please call 1-800-8-BATTERY for
information or contact your local recycling center.
51
HEADSET AND BELT CLIP INSTALLATION
CONNECTING AN OPTIONAL HEADSET TO THE HANDSET
Each handset may be used with an optional headset for hands free operation.
1. Remove the rubber cap covering the headset jack.
2. Connect the headset to the headset jack on the side of the handset. The
handset receiver and speakerphone microphone are disabled when the
headset is connected.
3. Adjust the headset to rest comfortably on top of your head and over
your ear. Move the microphone to approximately two to three inches
from your mouth.
4. Press the talk/callback button on the handset to answer a call or make
calls with the headset.
5. To return to normal operation, unplug the headset from the jack.
ATTACHING THE BELT CLIP
To attach the belt clip, insert the sides of the belt clip into the slots on each
side of the handset. Snap the ends of the belt clip into place.
52
Headset
jack
Headset
plug
Slot for
belt clip
Slot for
belt clip
DISPLAY MESSAGES
The following indicators show the status of a message or of the unit.
INCOMPLETE DATA Caller information has been interrupted during
transmission or the phone line is excessively noisy.
ENTER NAME Prompt telling you to enter the name in one of the
50 memory locations.
DELETE ALL? Prompt asking if you want to erase all Caller ID
records.
DELETE CALL ID? Prompt asking if you want to erase the current
Caller ID record that is shown on the display.
DELETE? Prompt asking if you want to erase one of the 50
numbers stored in the phone's outgoing memory.
END OF LIST Indicates that there is no additional information in
Caller ID memory.
NEW Indicates call or calls have not been reviewed.
UNKNOWN CALLER The incoming call is from an area not serviced by
Caller ID or the information was not sent
PAGING Someone has pressed the page/int button on the
base or handset.
BLOCKED NUMBER The person is calling from a number that has been
blocked from transmission.
REPT Repeat call message. Indicates that a new call from
the same number was received more than once.
SEARCHING Handset is searching the base.
NO DATA No Caller ID information was received.
OUT OF RANGE Handset is too far away from the base. Move closer to
the base.
53
HANDSET SOUND SIGNALS
Signal Meaning
A long warbling tone (with ringer on) Signals an incoming call
Three short beeps Page signal
One short beep (every 7 seconds) Low battery warning
TROUBLESHOOTING GUIDE
TELEPHONE SOLUTIONS
No dial tone
• Check or repeat installation steps.
• Make sure base power cord is connected to a working electrical outlet.
• Make sure the telephone line cord is connected to the base and the
modular phone jack.
• Connect another phone to the same jack; if there is still no dial tone, the
problem might be your wiring or local service.
• The cordless handset may be out of range of the base. Move closer to
the base.
• Make sure the battery is properly charged (12 hour s).
• Make sure the battery pack is installed correctly.
• Did the handset beep when you pressed the talk/callback button? The
battery may need to be charged.
• Place handset in charge cradle for at least 20 seconds to reset.
54
Dial tone is OK but can’t dial out
• Make sure the TONE/PULSE setting on the handset is set to the type of
phone service you are subscribed to.
Handset/Base does not ring
• Make sure the handset ringer is turned on and the base ringer is
programmed to HIGH.
• The cordless handset may be out of range of the base. Move closer to
the base.
•You may have too many extension phones on your line. Try unplugging
some phones.
• Check for dial tone.
You experience static, noise, or fading in and out
• The cordless handset may be out of range of the base. Move closer to
the base.
•Relocate the base. Make sure base is not plugged into an outlet with
another household appliance.
• Charge the battery.
Unit beeps
• Place the handset in the cradle for 20 seconds. If it still beeps, charge
battery for 12 hours.
• Clean charging contacts on cordless handset and charger with a soft
cloth or an eraser.
•See solutions for “No dial tone”.
•Replace the battery.
55
Charge indicator on the base flashes
•Provided your phone company offers voice message service and you
subscribe to it, the charge indicator on the base flashes when the phone
is not in use to indicate there is a message waiting. It stops flashing
after the message has been reviewed.
Memory Dialing doesn't work
• Did you program the memory location keys correctly?
• Did you follow proper dialing sequence?
Unit locks up and no communication between the base and cordless
handset
• Unplug the AC power supply from the wall outlet and the back of the
base. Remove the handset battery. Wait for 30 seconds and plug the
power adapter back into the base and wall outlet. Reconnect the battery
and charge for 12 hours. Re-register the handset.
CALLER ID SOLUTIONS
No Display
• Charge or replace the battery.
• Make sure that the unit is connected to a non-switched electrical outlet.
Disconnect the AC power supply from the base and reconnect it.
Caller ID Error Message
• The unit displays this message if it detects anything other than valid
Caller ID information during the silent period after the first ring. This
message indicates the presence of
noise on the line.
56
No Caller ID
•You must be subscribed to Caller ID service from your local telephone
company to receive Caller ID records.
BATTERY SOLUTIONS
If you experience any of the following problems, even after fully
recharging the battery, you may need to replace the battery pack:
• Short talk time
•Poor sound quality
• Limited range
• Charge indicator fails to light
GENERAL PRODUCT CARE
To keep your unit working and looking good, follow these guidelines:
•Avoid putting the phone near heating appliances and devices that
generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
•Avoid dropping the handset, as well as other rough treatment to
the phone.
• Clean the phone with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will
damage the finish.
•Retain the original packaging in case you need to ship the phone at a
later date.
•Periodically clean the charge contacts on the handset and base with a
clean pencil eraser.
57
CAUSES OF POOR RECEPTION
• Aluminum siding.
•Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
•You’re too close to appliances such as microwaves, stoves,
computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the house.
• Base is plugged into AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
•You’re out of range of the base.
SERVICE
If trouble is experienced with this equipment, for repair or warranty information,
please contact customer service at 1-800-448-0329. If the equipment is causing
harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
This product may be serviced only by the manufacturer or its authorized
service agents. Changes or modifications not expressly approved by
ATLINKS USA, Inc. could void the user’s authority to operate this product.
For instructions on how to obtain service, refer to the warranty included in
this guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the
date this product was purchased or recei ved as a gift. This information will
be valuable if service should be required during the warranty period.
Purchase date ________________ Name of store ________________________
58
INDEX
A
Accessory Order Form 61
Answering a Call 28
Area Code 15
Auto Standby 29
B
Base Layout 7
Basic Operation 27
Before You Begin 8
C
Call Timer 29
Caller ID 44
Caller ID Errors 50
Causes of Poor Reception 58
Chain Dialing from Memory 44
Connecting an Optional Headset to the
Handset 52
Connecting the AC (Electrical) Power 10
Connecting the Telephone Line 10
Cordless Handset Volume Control 35
D
Default 26
Deleting All Caller ID Records 49
Deleting the Caller ID Record Showing in
the Display 48
Deleting the Current Caller ID Record 48
Dialing a Caller ID Number 47
Dialing a Stored Number 43
Display Contrast 13
Display Messages 53
E
Equipment Approval Information 2
Exit 31
F
Features 5
Flash/Call Waiting 30
G
General Product Care 57
Global Deregistration 22
H
Handset and Charge Cradle Layout 7
Handset De-registration 21
Handset Registration 18
Handset Sound Signals 54
Headset and Belt Clip Installation 52
Hearing Aid Compatibility (HAC) 2
Hold 31
I
Important Installation Guidelines 9
Important Installation Information 9
Inserting a Pause in the Dialing
Sequence 41
Installing the Handset Battery 11
Installing the Phone 10
Intercom 36
Interference Information 2
Introduction 5
L
Language 12
Last Number Redial 31
Limited Warranty 62
59
M
Making a Call 28
Making an Intercom Call 36
Memory 39
Mute 34
P
Paging from the Base or Handset 32
Paging the Handset 32
Parts Checklist 8
Programmable Functions 12
R
Receiving an External Telephone Call
During an Intercom Call 37
Receiving an Intercom Call 37
Receiving and Storing Call Records 45
Replacing the Battery 51
Reviewing Call Records 45
Reviewing, Changing or Deleting Stored
Numbers 41
Ringer Tone 16
Ringer Volume Switch 29
S
Service 58
Speakerphone 27, 28
Speakerphone Volume Control 35
Storing a Name and Number
in Memory 39
Storing a Redial Number 41
T
Telephone Jack Requirements 8
Telephone Setup 12
Temporary Tone Dialing 35
Time of Day 25
Tone/Pulse 17
Transferring Calls 33
Transferring CID Records to Memory 46
Troubleshooting Guide 54
U
Using Intercom or Conference with
External Calls 37
Using the Soft Keys 12
W
Walkie Talkie 23
Wall Mounting the Base 12
60
✂
CUSTOMER: CUT ALONG DOTTED LINE.
ORM
F
TOTAL
$8.75
$18.35
5-2561
5-2562
$36.35
$11.90
5-2425
5-2459
PRICE*
MODEL NUMBER
$5.00
*Prices are subject to change without notice.
Total Merchandise.........................................$_______________
county, and locality to which the merchandise is being sent. Duties will apply for
shipments to Canada.
Sales Tax........................................................$_______________
Use VISA or Master Card or Discover preferably. Money order or check must be in U.S.
We are required by law to collect the appropriate sales tax for each individual state,
currency only. No COD or Cash. All accessories are subject to availability. Where
applicable, we will ship a superseding model.
Shipping/Handling....................................... $_______________
Total Amount Enclosed.................................$_______________
Mail order form and money order or check (in U.S. currency)
made payable to Thomson to:
Thomson
Mail Order Department
P.O. Box 8419
Ronks, PA 17573-8419
Name_______________________________________________________
Address_____________________________________ Apt.____________
City ________________________State________ ZIP_________________
Daytime Phone Number ( )_______________________________
RDER
DESCRIPTION
O
CCESSORY
A
Headset
Belt Clip
AC power adapter
Replacement Handset Battery
To order, call 1-800-338-0376 (for accessories only) or complete this order form.
Copy the number above your
For credit card purchases
Your complete charge card number, its expiration date and your
signature are necessary to process all charge card orders.
Copy your complete account number from your VISA card.
My card expires:
Copy your complete account number from your
Master Card or Discover.
name on the Master Card
My card expires:
____________________________________________________________________
61
Authorized Signature
Please make sure that this form has been filled out completely.
LIMITED WARRANTY
What your warranty covers:
• Defects in materials or workmanship.
For how long after your purchase:
• One year, from date of purchase.
(The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.)
What we will do:
• Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product’s
warranty period.
How you get service:
• Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original carton
and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period, must
be presented to obtain warranty service.” For rental firms, proof of first rental is also required. Also print your name and address and a
description of the defect. Send via standard UPS or its equivalent to:
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
• Pay any charges billed to you by the Exchange Center for service not covered by the warranty.
• Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.
•A new or refurbished unit will be shipped to you freight prepaid.
What your warranty
• Customer instruction. (Your Owner’s Manual provides information regarding operating instructions and user controls. Any additional
information, should be obtained from your dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modified or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
Product Registration:
• Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be
necessary. The return of the card is not required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY
DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A
GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC.
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT
OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED
WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE
APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How state law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your product outside the USA:
• This warranty does not apply. Contact your dealer for warranty information.
Model 21011
16047080 (Rev. 4 Dom E)
02-47
Printed in China
does not
cover:
ATLINKS USA, Inc.
101 West 103rd Street
Indianapolis, IN 46290
© 2002 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Loading...