RCA 14F512T User Manual
Television User’s Guide
Television
User’s Guide
Changing En ter tain ment. Again.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer
servicing to qualifi ed service personnel.
This symbol indicates that this product incorporates double insulation
between hazardous mains voltage and user accessible parts. When servicing
use only identical replacement parts.
This symbol indicates “dangerous voltage“ inside
the product that presents a risk of electric shock or
personal injury.
WARNING
To reduce the risk of fi re or electric
shock, do not expose this product to
rain or moisture.
The apparatus shall not be exposed
to dripping or splashing and no
objects fi lled with liquids, such as
vases, should be placed on the
apparatus.
This symbol indicates important instructions
accompanying the product.
Refer to the identifi cation/rating label located on the back panel of your product for
its proper operating voltage.
FCC Regulations state that unauthorized changes or modifi cations to this equipment
may void the user’s authority to operate it.
Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Caution: Using video games or any external accessory with fi xed images for
extended periods of time can cause them to be permanently imprinted on the
picture tube (or projection TV picture tubes). ALSO, some network/program logos,
phone numbers, black borders (sides, top and bottom), etc. may cause similar
damage. This damage is not covered by your warranty.
Cable TV Installer: This reminder is provided to call your attention to Article 820-40
of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1)
which provides guidelines for proper grounding and, in par tic u lar, specifi es that the
cable ground shall be connected to the grounding system of the building as close to
the point of cable entry as practical.
Important Stand and Base Safety Information
Choose the location for your TV carefully. Place the TV on a stand or base that is of
adequate size and strength to prevent the TV from being accidentally tipped over,
pushed off, or pulled off. This could cause personal injury and/or damage the TV.
Refer to the Important Safety Instructions on page 2.
Product Registration
Please fi ll out the product registration card (packed separately) and return it immediately. For US customers: Your RCA Consumer
Electronics product may also be registered at www.rca.com/productregistration. Registering this product allows us to contact you
if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and
model numbers in case you need them. These num bers are located on the product.
Model No. _________________ Serial No. _____________________Purchase Date: ________________________
Dealer/Address/Phone: __________________________________________________________________________
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
Read these instructions.
1.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifi ers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or third prong are provided for your safety. When the
provided plug does not fi t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specifi ed by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specifi ed by
13. Unplug this apparatus during lightning storms or when unused for
14. Refer all servicing to qualifi ed service personnel. Servicing is required
15. This product may contain lead and mercury. Disposal of these
16. Damage Requiring Service - The appliance should be serviced by
A. The power supply cord or the plug has been damaged;
the manufacturer or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
long periods of time.
when the apparatus has been damaged in any way, such as if the
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, or if the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
materials may be regulated due to environmental considerations. For
disposal or recycling information, please contact your local authorities
or the Electronic Industries Alliance (www.eiae.org).
qualifi ed service personnel when:
B. Objects have fallen or liquid has been spilled into the appliance;
C. The appliance has been exposed to rain;
D. The appliance does not appear to operate normally or exhibits a
marked change in performance;
E. The appliance has been dropped or the enclosure damaged.
17. Tilt/Stability - All televisions must comply with recommended
international global safety standards for tilt and stability proper ties of
its cabinet design.
• Do not compromise these design standards by applying excessive
pull force to the front, or top, of the cabinet, which could ultimately
overturn the product.
• Also, do not endanger yourself, or children, by placing electronic
equipment/toys on the top of the cabinet. Such items could
unsuspectingly fall from the top of the set and cause product damage
and/or personal injury.
18. Wall or Ceiling Mounting - The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
19. Power Lines - An outdoor antenna should be located away from
power lines.
20. Outdoor Antenna Grounding - If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to provide
some protection against voltage surges and built up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA No. 70-
1984, provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See Figure below.
21. Object and Liquid Entry - Care should be taken so that objects do
not fall and liquids are not spilled into the enclosure through openings.
22. Battery usage CAUTION - To prevent battery leakage that may result
in bodily injury, property damage, or damage to the unit:
• Install all batteries correctly, with + and - aligned as marked on the
unit.
• Do not mix batteries (old and new or carbon and alkaline, etc.).
• Remove batteries when the unit is not used for a long time.
23. Apparatus shall not be exposed to dripping or splashing and no
objects fi lled with liquids, such as vases, shall be placed on the
apparatus.
Note to the Cable TV system installer: This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC (Section
54 of the Canadian Electrical Code, Part 1) that provides guidelines for proper grounding and, in particular, specifi es that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
Example of Antenna Grounding
as per NEC - National Electrical Code
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250, PART H)
2
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
Table of Contents
Introduction
Safety/precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Getting Started
Basic Cable TV Connection . . . . . . . . . . . . . . . . . . . . . 4
Basic Antenna Connection . . . . . . . . . . . . . . . . . . . . . . 5
Basic TV to VCR Connection . . . . . . . . . . . . . . . . . . . . 6
Description of Buttons on the TV . . . . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup Menus
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TV/Cable TV (CATV) . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Search (Setting TV Channels) . . . . . . . . . . . . . . 12
Manual Channel Tuning . . . . . . . . . . . . . . . . . . . . . . . 13
Favorite Channel Setting . . . . . . . . . . . . . . . . . . . . . . 14
Adding or Erasing Channels . . . . . . . . . . . . . . . . . . . . 15
On-screen Menus
Picture Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Preset Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
On-Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Off-Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Parental Lock
Understanding Parental Lock . . . . . . . . . . . . . . . . . . . 23
Changing Your Password . . . . . . . . . . . . . . . . . . . . . . 24
Blocking Programming with Movie Ratings . . . . . . . . 25
Blocking Programming with TV Ratings . . . . . . . . . . . 26
Parental Lock Blocking Options . . . . . . . . . . . . . . . . . 27
Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Here are a few of the special features of your new
Color Television.
Automatic Channel Programming: Quick and easy
selection of available stations.
Child Lock (FPA Lock): Locks the buttons on the front
of the TV so it cannot be operated accidentally by young
children.
Closed Captioning: Allows you to read TV program
dialog or voice conversations as on-screen text.
Off-Timer: Turns off the TV at a preset time.
On-Timer: Turns on the TV at a preset time to a
designated TV channel or video source.
On-screen Menus: On-screen text (in English, French, or
Spanish) for setting TV controls.
Parental Lock: Allows you to block the viewing of certain
TV channels if you do not want your children viewing
inappropriate material.
Remote control: Operates your TV and navigates the
menus.
Sleep Timer: Turns off the TV within an amount of time
you specify. 10-120 minutes from the current time.
Picture Preset Mode: Lets you set the picture’s color,
tint, contrast, etc. for various types of programming.
Settings include Bright, Normal, Theater, and Personal,
which set the picture control as you want.
Sound Mode: Lets you set the TV’s sound for the
current programming. Choices include Personal, Theatre,
Concert, or Speech.
Standard broadcast (VHF/UHF) or Cable TV channel
capability.
Stereo Capability: Includes built-in amplifi er twinspeaker system; allows reception of TV programs
broadcast in stereo.
Sound
Sound Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . 29
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Stereo and Second Audio Program . . . . . . . . . . . . . . 32
Others
Notebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . 36
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . .36-37
3
Basic Cable TV Connection
The Cable TV signal into your home may be a single cable (75 ohm ) or may include a Cable Box. In either case, the
connection to the TV is easy.
If your Cable TV signal comes directly via a 75 ohm coaxial cable, using the following steps:
Connect the Cable TV signal to the 75 ohm ANTENNA INPUT jack on the rear of the TV. Screw it down tight.
Plug the TV’s power cord into a power outlet and turn on the TV. Set TV/CATV to CATV as detailed on page 11. Refer
to AUTO SEARCH to set up your available TV channels. Details are on page 12.
If you have a Cable Box, use the following steps:
Connect the Cable TV signal to the IN jack on the Cable Box.
Connect a separate coaxial cable to the OUT jack on the Cable Box and to the 75 OHM ANTENNA INPUT jack on the
rear of the TV.
Plug the TV’s power cord into a power outlet and turn on the TV. Set TV/CATV to CATV as detailed on page 11.
Set the TV to channel 3 or 4 (the same as the channel 3/4 switch on your Cable Box if applicable).
Change channels at the Cable Box.
Helpful Hints
An RF coaxial cable (to connect the Cable Box to the TV)
may be supplied by the Cable
TV company. It is not supplied
with the TV.
You can connect a Satellite
Receiver the same way you
would connect a Cable Box.
Your Cable Box may have
separate Audio and Video Out
jacks instead. If so, use audio
and video cables to connect
the AUDIO/VIDEO OUT jacks
of the Cable Box to the AUDIO/
VIDEO INPUT jacks.
Press the INPUT button on
the remote control to set the
TV to the correct video input
channel. For front inputs
choose FRNT. For rear AV
inputs choose VIDEO.
Your model has an S-Video
input, choose S-VIDEO.
Change the channel at the
Cable Box.
4
Basic Antenna Connection
A combination antenna receives normal broadcast channels (VHF 2-13 AND UHF 14-69). Your connection is easy since
you will connect the antenna to the 75 OHM ANTENNA INPUT jack on the rear of the TV.
If your antenna has a round cable (75 ohm) on the end, then you are ready to connect it to the TV. Go to the next step.
If your antenna has fl at twin-lead wire (300 ohm), you fi rst need to attach the antenna wires to the screws on a 300 to
75 ohm adapter (not supplied with your TV).
Push the round end of the adapter or antenna cable onto the 75 OHM ANTENNA INPUT jack on the rear of the TV. If
the round end of the antenna cable is threaded, screw it down tight.
Plug the TV’s power cord into a power outlet and turn on the TV. Set TV/CATV to TV mode as detailed on page 11.
Refer to AUTO SEARCH to set up your available TV channels. Details are on page 12.
Before plugging the UHF/VHF Rod Antenna into the
ANTENNA INPUT jack, check that the pin is not bent. If
it is bent, straighten the pin as illustrated, then plug the
pin into the jack.
Bent pin
Cable
Plug
(Needs to be straightened)
(Straight pin)
FCC WARNING -This equipment may generate or use radio
frequency energy. Changes or modifi cations to this equipment
may cause harmful interference unless the modifi cations are
expressly approved in the instruction Manual. The user could
lose the authority to operate this equipment if an unauthorized
change or modifi cation is made.
VHF
Antenna
(Not supplied)
VHF/UHF
Combination Antenna
(Not supplied)
*Some cable TV systems use scrambled
signals and require a special converter to
UHF
Antenna
(Not supplied)
VHF/UHF
Combiner
(Not supplied
CATV Box*
or Satellite Box
(Not supplied)
OUT
75-ohm
OR OR
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of
the NEC (Section 54 of the Canadian Electrical Code, Part 1) that provides guidelines for
proper grounding and, in particular, specifi es that the cable ground shall be connected to
the grounding system of the building as close to the point of cable entry as practical.
ANT. IN
Coaxial Cable
receive these channels. Consult your local
cable company.
IN
From Cable System
or Satellite Antenna
75-ohm
Coaxial Cable
From Cable System
CABLE TV / ANTENNA CONNECTIONS
Helpful Hints
If you have separate UHF and
VHF antennas, you need an
optional combiner to connect
the antennas to the TV.
5
Basic TV to VCR Connection
The basic component (VCR, DVD player etc.) to TV connection is described below. For other hookups, refer to your
component’s instruction manual.
Connect the audio cables (white and red) to the AUDIO INPUT jacks on the TV and to the AUDIO OUT jacks on the
VCR (or other component). Match the cable color to the jack color.
If your component has an S-Video jack, connect an S-Video cable to the S-VIDEO jack on the back of the TV to the
S-Video jack on the component. If your component doesn’t have an S-Video jack go to item 3.
Connect a video cable (yellow) to the VIDEO INPUT jack on the TV and to the VIDEO OUT jack on your VCR (or other
component).
Turn on the TV and the other component.
Press the INPUT button on the remote control until the correct video input channel appears in the upper right corner of
the TV screen. When you play material on the VCR, DVD player, etc. that is connected to the AUDIO and VIDEO jacks
it will appear on the TV on the video input channel. (The bottom of page 4 has a complete list.)
INPUT OUTPUT
VIDEO
VIDEO
S-VIDEO
Model 24F512T back panel
75 OHM
ANTENNA
R-AUDIO-L
S-VIDEO
Models 20F511T, 20F512T back panel
INPUT
VIDEO
INPUT
OUTPUT
L(mono)
AUDIO
R
AUDIO
Helpful Hints
Audio and video cables are not supplied
with the TV. Audio cables are usually red
and white. Video cables are usually yellow.
Your VCR may not have Audio and Video
Out jacks, but only an RF or ANTENNA
OUT jack.
Use a coaxial cable to connect the VCR’s
ANTENNA OUT jack to the TV’s 75 OHM
ANTENNA INPUT jack.
75 OHM
ANTENNA
INPUT
L
R
R
AUDIO
L(MONO)
Models 27V512T and 27V513T back panel
VIDEO
Models 20F511T, 20F512T,
24F512T, 27V512T and
27V513T side AV panel (front)
S-Video provides a clearer picture than
the standard video (the yellow jack).
Choose the S-VIDEO channel to view
material playing on equipment connected
to the S-VIDEO jack.
Use either S-VIDEO jack or VIDEO INPUT
jacks. Do not use both at the same time
for the same piece of equipment. This
would interfere with the picture display. If
both are used, S-VIDEO has priority over
the yellow VIDEO INPUT jack.
75 OHM
ANTENNA
INPUT
S-VIDEO
INPUT
VIDEO
L
AUDIO
R
Please note that models 27V512T and
27V513T have only AV inputs.
6
Description of Buttons on the TV
Front View buttons
Front Panel Buttons (Models 20F511T, 20F512T and
24F512T)
If you cannot locate your remote, you can use the
buttons on the front of your TV to operate many of the
TV’s features.
Your button layout and design may differ from above.
Front View
STANDBY (LED INDICATOR) Lights to show AC power
is available.
SENSOR Receives infra-red signals from the remote.
POWER Turns the TV on and off.
TV/VIDEO
MENU VOLUME - VOLUME +
CHANNEL - CHANNEL +
43 2 1
Top View
1. CHANNEL BUTTONS Selects channel numbers. In the
menu system, acts like the up or down arrow buttons.
Use to highlight items.
2. VOLUME BUTTONS Press to decrease/increase the
volume. In the menu system, acts like the right or left
arrow buttons. Press to select highlighted items and
make adjustments.
3. MENU Press to display the main menu. Press for the onscreen display to clear the screen.
4. TV/VIDEO (INPUT) Choose between TV programming
and the AV input.
MENU
VOL
VOL
CH
CH
POWER
Front Panel Buttons (Model 27V512T and 27V513T)
Front View
MENU Brings up the Main menu. Press for the
on-screen display to clear the screen.
VOLUME BUTTONS Press to decrease/increase the
volume. In the menu system, acts like the right or left
arrow buttons. Press to select highlighted items and
make adjustments.
CHANNEL BUTTONS Selects channel numbers. In the
menu system, acts like the up or down arrow buttons. Use to
highlight items.
SENSOR Receives infra-red signals from the remote.
POWER Turns the TV on and off. Lights to show TV is on.
7
Battery Installation
To load batteries into the remote control:
Remove the battery compartment lid
on the rear of the remote. Press in the tab,
then lift off the lid.
Place two AA batteries in the remote. Be
sure the (+) and (-) ends of the batteries line
up correctly (as marked inside the battery
compartment).
Reattach the battery compartment lid.
Effectively Using the Remote Control
Point the remote control toward the remote
sensor on the front of the TV when operating
the TV with the remote control.
Remote Control
8
Remote Control
When operating the remote, point it directly at the front of the TV. Objects
between the remote and the remote sensor can block the signal to the TV.
CALENDAR
Press to display or close the calendar.
CAPS Press to toggle the entry mode between uppercase or lowercase letters.
Details are on page 33.
CHANNEL +/- Buttons Press to select memorized TV channels.
system, acts like the up or down arrow buttons and adjusts menu controls.
In the menu
CC (C.Mute) Press to turn on/off C.Mute function directly. Details are on page 21.
INFO/DEL(ETE) Press to see the current channel number, and sound information
on the TV screen. Press again to display the current time on the screen.
Press to remove a menu from the screen.
In Notebook mode, press to delete unwanted text. Details are on page 33.
INPUT Press to select TV channels or the Audio/Video IN channels. Page 4 has a
complete list.
INSERT In Notebook mode, press to select INS(ERT) or OVR (overwrite). Details are
on page 33.
FAV(ORITE) Press to browse the channels in your Favorite List. Details are on page
14.
GO BACK Press to return to the previously viewed channel.
MENU Press to see the TV’s on-screen menu. Press to go back to the previous
menu or to remove a menu from the screen.
MTS Press to select a sound mode if available with the TV programming: MONO,
STEREO, and SAP. Details are on page 32.
MUTE Press to mute or restore the TV sound. Pressing the volume buttons (VOLUME + or VOL+) also will cancel mute
and restore the sound.
NOTEPAD Press to display or close the NOTEBOOK window.
NUMBER Buttons When the TV/Cable menu option is in the TV position, all channels can be selected by using two
buttons. For example, to select channel 2, press “0” then “2”. You can also just press “2”.
For channels 100 and above, press three number buttons of the channel directly. (You can select channels above 69 only if
you have Cable TV. Make sure TV/CATV is set to CATV. Details are on page 11.)
In Notebook mode, press to enter a letter, a digit or a symbol. Details are on page 33.
OK
Within the on-screen menu, press to select some special function, such as Favorite list, etc.
ON-OFF Press to turn the TV on or off. You also can turn on the TV by pressing the CHANNEL +/- buttons on the front
of the TV.
PRESETS Press to select one of the four preset Picture settings (Bright, Normal, Theater or Personal). Details are on page 17.
SLEEP Press to select a time period (120 minutes to 10 minutes in 10-minute decrements) after which the TV will turn
itself off. Details are on page 22.
SOUND Press to select one of the four sound settings (Theater, Concert, Speech or Personal). Details are on page 29.
VOLUME +/- Buttons Press to adjust the TV sound level.
and adjusts menu controls.
In the menu system, acts like the right or left arrow button
9
Language
You can set the TV’s on-screen menu to
English, French or Spanish.
Press MENU to see the main menu.
Press CH+ or CH- to highlight
Preferences.
Press OK to enter the Preferences
submenu.
Language is highlighted. Press VOL+
or VOL- to select English, Francais
(French), or Espanol (Spanish).
Press MENU repeatedly to exit the menu
or the menu will automatically disappear
within a few seconds if no buttons are
pressed on the remote control.
Main Menu
Picture
Sound
Preferences
Time
Setup
Main Menu
Picture
Sound
Preferences
Time
Setup
Preferences
Language
English
CC C.Mute
Par. Control
FPA Lock Off
Helpful Hints
The language control only
affects the language of the TV
menus. It does not change the
other on-screen text features,
such as Closed Captions.
10
TV/Cable TV (CATV)
It is important for the TV to know what type of
signal-Cable TV (CATV) or a normal antenna
you are using. Choose your signal (Antenna or
Cable):
Press MENU to see the main menu.
Press CH+ or CH- to highlight Setup.
Press OK to enter the Setup submenu.
TV/CATV is highlighted. Press VOL+ or
VOL- to select TV or CATV.
Choose CATV if you have Cable TV
service. (See page 4 for connection
details.) If you do not have Cable TV
service and you connected an antenna
to the TV, choose TV. (See page 5 for
connection details.)
Press MENU repeatedly to exit the
menu or the menu will automatically
disappear within a few seconds if no
buttons are pressed on the remote
control.
Main Menu
Picture
Sound
Preferences
Time
Setup
Main Menu
Picture
Sound
Preferences
Time
Setup
Setup
TV/CATV CATV
Channel 1
Add/Erase Erase
Manual Down
Auto Search
Favorite List
Setup
TV/CATV CATV
Channel 7
Add/Erase Erase
Manual Down
Auto Search
Favorite List
Helpful Hints
When CATV is selected,
channels 1-125 are available.
When TV is selected, only
channels 2-69 are available.
You cannot select the Setup
menu if the TV is set to a video
input channel (FRNT). Press
INPUT repeatedly to get to
regular TV programming.
11
Auto Search (Setting TV Channels)
You can set your TV to receive local TV
channels (from an antenna) or Cable TV
channels (when you have Cable TV service).
Then, use Auto Search to set up channels that
are available for you. This makes it easy for
you to select only the available TV stations
when you press CH+ or CH-. Before you start
Auto Search, make the Antenna or Cable TV
connection described on pages 4 and 5. In the
menu select TV or Cable (CATV) as described
on page 11.
Press MENU to see the main menu.
Press CH+ or CH- to highlight Setup.
Press OK to enter the Setup submenu.
Press CH+ or CH- repeatedly to
highlight Auto Search.
Press VOL+ to start programming TV
channels. Press VOL- if you need to
stop channel programming during the
process.
When channel setup is completed, the TV
will go to its lowest channel.
Main Menu
Picture
Sound
Preferences
Time
Setup
Main Menu
Picture
Sound
Preferences
Time
Setup
Setup
TV/CATV CATV
Channel 1
Add/Erase Erase
Manual Down
Auto Search
Favorite List
Searching
Please Wait
Stop
TV 2
Helpful Hints
Press CH+ or CH- to see
which channels are in the TV’s
memory. You can also select
channels that have not been
memorized using the number
buttons on the remote control.
To delete unwanted channels
from the TV s memory or to
add more channels, see ADD/
ERASE on page 15.
You cannot select the Setup
menu if the TV is set to a video
input channel (FRNT). Press
INPUT repeatedly to get to
regular TV programming.
12
Loading...