Raypak 206A, 266, 266A, 336A, 399 User Manual

...

Download

INSTALLATION AND OPERATION MANUAL

Gas-Fired Pool and Spa Heater

Brass ASME and Polymer Atmospheric Heat Exchanger Models 206A, 266, 266A, 336A, 399, and 406A

WARNING: If the information in the instructions is not followed exactly, a re or explosion may result

causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids or other combustible materials in the vicinity of this or any other appliance. To do so may result in an explosion or fire.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

This manual should be maintained in legible condition and kept adjacent to the heater or in a safe place for future reference.

Catalog No. 6000.59AJ

E󰀨ective: 03-02-20 Replaces: 12-16-19 P/N 241236 Rev. 36

QUICK START GUIDE

CLEARANCES

 Space required: See page 12.

 Minimum and service clearances: See page 7 for

clearances table. Note that local codes prevail.

PIPING

 Pressure relief valve: See page 20 for recommended

PRV orientation.

 Flow rates: See page 17 for ow rate values.

GAS

 Distance to regulator (pipe lengths) and gas inlet

sizes: See page 17.

 Required pressure for Natural Gas:

Min = 6" WC, Max = 10.5" WC

 Required pressure for Propane Gas:

Min = 12" WC, Max = 13" WC

 Sediment trap is required for all installations.

See page 15.

WATER CHEMISTRY

 Water chemistry requirements: See page 5.

POWER

 Supply voltage: See page 23 for acceptable input

voltages.

VENTING

 Materials: See pages 11 and 14.

 D-2 Power Vent Kit: See page 14.

 Indoor Stack: See page 11.

CONTROLS INTERFACE

 Wiring diagrams: See page 24 and 25.

 User interface: See pages 26 and 27.

 Remote operation: See page 30.

Revision 36 reects the following changes:

Removed from illustration items 19-M and 20-M on page 46. Updated parts list items 9-C with service kit 018304F on page 48. Added item 1-M service kit 018297F on page 49. Updated items 11-HM, 28-HM and 6-M on page 49. Removed items 19-M and 20-M on page 49. Updated items 4-S and 9-S on page 50.

CONTENTS

1. WARNINGS ............................................................. 4

Pay Attention to These Terms ................................. 4

2. WATER CHEMISTRY ............................................. 5

Automatic Chlorinators and Chemical Feeders....... 5

3. BEFORE INSTALLATION ...................................... 6

Receiving equipment............................................... 6

Rating and certications .......................................... 6

Elevation ................................................................. 6

Ambient Temperature Rating .................................. 6

4. INSTALLATION ....................................................... 7

Installation Codes.................................................... 7

Clearances .............................................................. 7

Outdoor Heater Installation ..................................... 8

Combustion and Ventilation Air ............................. 11

Vent Piping ............................................................ 14

D-2 Power Vent Kit ................................................ 14

Gas Supply Connections....................................... 15

Flow Rate .............................................................. 17

ProTek Shield Assembly........................................ 18

Unitherm Governor Operation ............................... 19

Internal Automatic Bypass Valve ........................... 19

External Auxiliary Bypass Valve ............................ 19

Auxiliary Bypass Valve Adjustment .......................20

Pressure Relief Valve Installation .......................... 20

Heat Exchanger Reversal ..................................... 20

Plumbing Diagrams ............................................... 21

6. WIRING DIAGRAM - MILLIVOLT ....................... 24

7. WIRING DIAGRAM - DIGITAL ............................ 25

8. CONTROLS ........................................................... 26

Control Panel Removal ......................................... 26

Control Adjustments - Millivolt Models ..................26

Control Adjustments – Digital Models ...................27

Operation .............................................................. 27

Status and Diagnostics ......................................... 29

Remote Control Wiring - Digital Models Only........ 30

9. OPERATING INSTRUCTIONS ............................ 36

Before Start-Up ..................................................... 36

Start-Up Procedures ............................................. 36

Visual inspection ...................................................36

Water Pressure Switch .......................................... 36

10. MAINTENANCE AND CARE ............................... 39

Cold Weather Operation .......................................39

11. TROUBLESHOOTING ......................................... 40

Millivolt - Flow Chart .............................................. 41

Digital - Flow Chart................................................ 42

Control Logic - Flow Chart - Digital ....................... 43

12. REPLACEMENT PARTS ..................................... 44

13. ILLUSTRATED PARTS LIST .............................. 45

5. ELECTRICAL WIRING ......................................... 22

Millivolt Models ("M" su󰀩x) ................................... 22

Digital Models ("E" su󰀩x) ...................................... 22

Electrical Power Draw ........................................... 23

Transformer Wiring ...............................................23

NOTE: ProTek Shield Adapter and assembly shown for ASME models in Figures, but not available until March 2020.

1. WARNINGS

Pay Attention to These Terms

DANGER

WARNING

CAUTION

NOTE

DANGER: Failure to install the drafthood on indoor

installation and properly vent the heater to the outdoors as outlined in the venting section of this manual can result in unsafe operation of the heater. To avoid the risk

of re, explosion, or asphyxiation from carbon monoxide,

never operate this heater unless it is properly vented and has an adequate air supply for proper operation. Be sure to inspect the vent system for proper installation at initial start-up, and at least annually thereafter. Refer to the venting section of this manual for more information regarding vent system inspections.

Indicates the presence of immediate hazards which will cause severe personal injury, death or substantial property damage if ignored.

Indicates the presence of hazards or unsafe practices which could cause severe personal injury, death or substantial property damage if ignored.

Indicates the presence of hazards or unsafe practices which could cause minor personal injury or product or property damage if ignored.

CAUTION used without the warning alert symbol indicates a potentially hazardous condition which could cause minor personal injury or product or property damage if ignored.

Indicates special instructions on installation, operation, or maintenance which are important but not related to personal injury hazards.

WARNING: Improper installation, adjustment,

alteration, service, or maintenance can cause property damage, personal injury or loss of life. Installation

and service must be performed by a qualied installer,

service agency, or the gas supplier.

WARNING: Gasoline, as well as other ammable

materials and liquids (adhesives, solvents, etc.), and the vapors they produce, are extremely dangerous. Do

not handle, use, or store gasoline or other ammable or

combustible materials in the vicinity of a heater.

WARNING: To minimize the possibility of improper

operation, serious personal injury, re, or damage to the heater:

• Always keep the area around the heater free of

combustible materials, gasoline, and other ammable

liquids and vapors.

• Heater should never be covered or have any blockage

to the ow of fresh air to the heater.

WARNING: This unit contains refractory ceramic

ber (RCF) insulation in the combustion chamber. RCF,

as manufactured, does not contain respirable crystalline silica. However, following sustained exposure to very high temperatures [>2192°F (1200°C)], the RCF can transform into crystalline silica (cristabolite). The International Agency for Research on Cancer (IARC) has

classied the inhalation of crystalline silica (cristabolite)

as carcinogenic to humans.

When removing the burners or heat exchangers, take precautions to avoid creating airborne dust and avoid

inhaling airborne bers. When cleaning spills, use wet sweeping or High E󰀩ciency Particulate Air (HEPA) ltered vacuum to minimize airborne dust. Use feasible

engineering controls such as local exhaust ventilation or dust collecting systems to minimize airborne dust. Wear appropriate personal protective equipment including gloves, safety glasses with side shields, and

appropriate NIOSH certied respiratory protection, to avoid inhalation of airborne dust and airborne ber

particles.

WARNING: Both natural gas and propane have

an odorant added to aid in detecting a gas leak. Some people may not physically be able to smell or recognize this odorant. If you are unsure or unfamiliar with the smell of natural gas or propane, ask your local gas supplier. Other conditions, such as “odorant fade,” which causes the odorant to diminish in intensity, can

also hide, camouage, or otherwise make detecting a gas leak by smell more di󰀩cult.

WARNING: UL-recognized fuel gas detectors are

recommended in all enclosed propane and natural gas applications wherein there is a potential for an explosive mixture of fuel gas to accumulate and their installation should be in accordance with the detector manufacturer’s recommendations and/or local laws, rules, regulations, or customs.

WARNING: Do not install within 3 feet (0.9 m) of

a heat pump or an outdoor condensing unit. Strong air intake from this type of equipment can disturb the combustion process and cause damage or personal injury.

WARNING: The heater shall not be located in an

area where water sprinklers, or other devices, may cause water to spray through the cabinet louvers and into the heater. This could cause internal rusting or damage electrical components, and void the warranty.

CAUTION: Elevated water temperature can be

hazardous. The U.S. Consumer Product Safety

Commission has these guidelines:

1. Spa water temperatures should never exceed 104°F (40°C). A temperature of 100°F (38°C) is considered safe for a healthy adult. Special caution is suggested for young children.

2. Drinking of alcoholic beverages before or during spa or hot tub use can cause drowsiness which could lead to unconsciousness and subsequently result in drowning.

3. Pregnant Women Beware! Soaking in water over

102°F (39°C) can cause fetal damage during the rst

three months of pregnancy resulting in the birth of a brain-damaged or deformed child. Pregnant women should stick to the 100°F (38°C) maximum rule.

4. Before entering the spa or hot tub, users should check the water temperature with an accurate thermometer; spa or hot tub thermostats may err in regulating water temperatures by as much as 4°F (2.2°C).

5. Persons with a medical history of heart disease, circulatory problems, diabetes, or blood pressure problems should obtain a physician’s advice before using pools or hot tubs.

6. Persons taking medications which induce drowsiness, such as tranquilizers, antihistamines, or anticoagulants, should not use spas or hot tubs.

CAUTION: Propane gas is heavier than air and will

settle on the ground. Since propane can accumulate in

conned areas, extra care should be exercised when

lighting propane heaters.

2. WATER CHEMISTRY

NOTE: Corrosive water voids all warranties.

Chemical imbalance can cause severe damage to your heater and associated equipment. Maintain your water chemistry according to Table A. If the mineral content and dissolved solids in the water become too high, scale forms inside the heat exchanger tubes, reducing heater e󰀩ciency and damaging the heater. If the pH drops below

7.2, this will cause corrosion of the heat exchanger and

severely damage the heater. Heat exchanger damage

resulting from chemical imbalance is not covered by the warranty.

For your health and the protection of your pool equipment, it is essential that your water be chemically balanced. The following levels must be used as a guide for balanced water.

CAUTION: Free chlorine must not exceed 5 ppm

which can damage the heater and is not covered under warranty.

• Occasional chemical shock dosing of the pool or spa water should not damage the heater providing the water is balanced.

• Automatic chemical dosing devices and salt chlorinators are usually more efficient in heated water, unless controlled, they can lead to excessive chlorine level which can damage your heater.

• Check valve should be installed between the heater outlet and a chlorinator or other chemical dosing device.

• Further advice should be obtained from your pool or spa builder, accredited pool shop, or chemical supplier for the correct levels for your water.

Automatic Chlorinators and Chemical Feeders

All chemicals must be introduced and completely diluted into the pool or spa water before being circulated through the heater. Do not place sanitizing chemicals in the skimmer. High chemical concentrations will result when the pump is not running (e.g. overnight).

Chlorinators must feed downstream of the heater and have an anti-siphoning device to prevent chemical backup into the heater when the pump is shut o󰀨.

See "Plumbing Diagrams" on page 21.

NOTE: High chemical concentrates from feeders and chlorinators that are out of adjustment will cause rapid corrosion to the heat exchanger. Such damage is not covered under the warranty.

Recommended Level(s) Fiberglass Pools Fiberglass Spas Other Pool and Spa Types

Water Temperature 68-88°F (20-31°C) 89-104°F (31-40°C) 68-104°F (20-40°C)

pH 7.3-7.4 7.3-7.4 7.6-7.8

Total Alkalinity (ppm) 120-150 120-150 80-120

Calcium Hardness (ppm) 200-300 150-200 200-400

Salt (ppm) 4500 Maximum 4500 Maximum 4500 Maximum

Free Chlorine (ppm)* 2-3 2-3 2-3

Total Dissolved Solids (ppm) 3000 Maximum** 3000 Maximum** 3000 Maximum**

*Free Chlorine MUST NOT EXCEED 5 ppm! **In saltwater chlorinated pools, the total TDS can be as high as 6000 ppm.

Table A. Pool Water Chemistry

3. BEFORE INSTALLATION

Receiving equipment

The manufacturer recommends that this manual be reviewed thoroughly before installing the pool/spa heater. If there are any questions that this manual does not answer, please contact the factory or your local representative.

On receipt of your equipment visually check for external damage to the carton. If the carton is damaged, a note should be made on the Bill of Lading when signing for the equipment. Remove the heater from the carton. If it is damaged, report the damage to the carrier immediately. Save the carton.

These items are shipped inside a box in the carton with the heater:

Standard Unit (POLYMER HEADERS)

1. “Pagoda” top

2. 2" CPVC union half with "O" rings (2)

3. Plastic pipe finish flange for gas line

4. Bonding lug with mounting screw (Digital) models only)

ASME Unit (BRASS HEADERS)

1. “Pagoda” top

2. 2" CPVC union half with "O" rings (2)

3. Plastic pipe finish flange for gas line

4. Bonding lug with mounting screw (Digital models only)

5. Pressure Relief Valve (PRV)

6. Protek Shield™ Adapter with Protek Shield Assy,

O-ring and wing nut (March 2020 onward)

THE MODEL AND SERIAL NO. CAN ALSO BE FOUND INSIDE THE BEZEL ABOVE THE DISPLAY

Rating and certications

These heaters are design-certied and tested under the latest requirements of the ANSI Z21.56 / CSA 4.7 Standard for Gas-Fired Pool Heaters. All heaters can be used either indoor or outdoors when appropiate venting is installed. The appropriate top designated for each type of use is required. If necessary, the top can be changed at a later date to change from outdoor to indoor or vice versa.

All brass header units have heat exchangers which are ASME-certied (BPV Section IV part HLW) and are registered with National Board.

Elevation

Rated inputs are suitable for up to 2,000 ft (610 m) elevation. For elevations above 2,000 ft (610 m), reduce input 4% for each 1,000 ft (305 m) above sea level, as high elevation reduces combustion performance.

Ambient Temperature Rating

Heater Components

Millivolt Heater with Honeywell Gas Valve 32°F to 175°F (0°C to 79°C)

Millivolt Heater with Robertshaw Gas Valve 0°F to 175°F (-18°C to 79°C)

Electronic Ignition Heater* -32°F to 175°F (-35°C to 79°C)

*Requires 120 or 240VAC, 1 Ph, 60 Hz Power Supply

MODEL AND SERIAL NO. LOCATED ON RATING PLATE

Figure 1. Rating Plate Location

F10640-1

Be sure that you receive the number of packages indicated on the Bill of Lading.

4. INSTALLATION

WARNING: This unit contains refractory ceramic

ber (RCF) insulation in the combustion chamber. RCF,

as manufactured, does not contain respirable crystalline silica. However, following sustained exposure to very high temperatures (>2192°F), the RCF can transform into crystalline silica (cristabolite). The International

Agency for Research on Cancer (IARC) has classied

the inhalation of crystalline silica (cristabolite) as carcinogenic to humans.

When removing the burners or heat exchangers, take precautions to avoid creating airborne dust and avoid

inhaling airborne bers. When cleaning spills, use wet sweeping or High E󰀩ciency Particulate Air (HEPA) ltered vacuum to minimize airborne dust. Use feasible

appropriate NIOSH certied respiratory protection, to avoid inhalation of airborne dust and airborne ber

particles.

IMPORTANT NOTICE: These instructions are intended

only for the use by qualied personnel, specically

trained and experienced in the installation of this type of heating equipment and related system components. Installation and service personnel may be required by some states to be licensed. If your state is such, be sure your contractor bears the appropriate license. Persons

not qualied shall not attempt to x the equipment nor

attempt repairs according to these instructions.

WARNING: Improper installation, adjustment,

alteration, service or maintenance may damage the equipment, create a hazard resulting in asphyxiation,

explosion or re, and will void the warranty.

NOTE: The heater should not be located in an area where possible water leakage will result in damage to the area adjacent to the heater or to the structure. When such locations cannot be avoided, it is recommended that a suitable drain pan, with adequate drainage, be installed under the heater. The pan must not restrict

combustion air ow.

Installation Codes

Installation must be in accordance with local codes, or, in the absence of local codes, with the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA54 and National Electrical Code, ANSI/NFPA 70, and for Canada, the latest edition of CAN/CSA-B149 Installation Codes, and Canadian Electrical Code, CSA C22.1 Part 1 and Part 2.

Clearances

All Heaters

For indoor and outdoor clearances from combustible surfaces, see the chart below.

Location Indoor Installation

Top * 30" (762 mm) Drafthood

Front Alcove (Open)

Vent 6" (152 mm)

Floor ** 0"

Back 6" (152 mm)

Right Side 12" (305 mm) Water Side

Left Side 6" (152 mm) Opposite Water Side

Location Outdoor Installation

Top * Unobstructed (Outdoor Stack)

Top *** 36" (914 mm) (Stackless Top)

Floor 0"

Back 6" (152 mm)

Right Side 12" (305 mm) Water Side

Left Side 6" (152 mm) Opposite Water Side

* Clearance from top of vent terminal ** Do not install on carpeting *** Clearance from top of heater

Table B. Minimum Clearances from Combustible Surfaces

When installed according to the listed minimum clearances from combustible construction, the pool heater can still be serviced without removing permanent construction around the heater.

However for ease of servicing, we recommend a clearance of at least 24" (610 mm) in the front, and at least 18" (457 mm) on the water connection side. This will enable the heater to be serviced in its installed location, that is, without movement or removal of the heater.

Description Location

Back 9 (229)

a. 3-1/2" (89 mm) thick

masonry walls without ventilated air space

b. 1/2" (13 mm)insulation

board over 1" (25 mm) glass ber or mineral wool batts

c. 0.024 sheet metal over

1" (25 mm) glass ber or mineral wool batts reinforced with wire on rear face with ventilated air space

d. 3-1/2" (89 mm) thick

masonry wall with ventilated air space

e. 0.024 sheet metal with

ventilated air space

f. 1/2" (13 mm) thick

insulation board with ventilated air space

g. 0.024 sheet metal with

ventilated air space over

0.024 sheet metal with ventilated air space.

h. 1" (25 mm) glass ber

or mineral wool batts sandwiched between two sheets 0.024 sheet metal with ventilated air space

Derived from National Fuel Gas Code, Table 10.2.3

Table C. Reduction of Clearances to Protected Surfaces

Right 9 (229) Left 9 (229) Vent 5 (127) Indoor Top 39 (991) Outdoor Top Unobstructed Back 6 (152) Right 6 (152) Left 6 (152) Vent 3 (76) Indoor Top 30 (762) Outdoor Top Unobstructed Back 4 (102) Right 4 (102) Left 4 (102) Vent 3 (76) Indoor Top 24 (610) Outdoor Top Unobstructed Back 6 (152) Right 6 (152) Left 6 (152) Vent 6 (152) Indoor Top 39 (991) Outdoor Top Unobstructed Back 4 (102) Right 4 (102) Left 4 (102) Vent 2 (51) Indoor Top 24 (610) Outdoor Top Unobstructed Back 4 (102) Right 4 (102) Left 4 (102) Vent 3 (76) Indoor Top 24 (610) Outdoor Top Unobstructed Back 4 (102) Right 4 (102) Left 4 (102) Vent 3 (76) Indoor Top 24 (610) Outdoor Top Unobstructed Back 4 (102) Right 4 (102) Left 4 (102) Vent 3 (76) Indoor Top 24 (610) Outdoor Top Unobstructed

Distance

in. (mm)

Clearances less than these may require removal of the heater to service either the heat exchanger or the burner tray. In either case, the heater must be installed in a manner that will enable the heater to be serviced without removing any structure around the heater.

Flooring

This heater can be installed on combustible ooring. The combustible clearances listed can be reduced by protecting the exposed combustible surfaces as shown in

Table C.

Outdoor Heater Installation

These heaters are design-certied for outdoor installation, when equipped with the approved tops designated for outdoor use.

WARNING: The heater shall not be located in an

WARNING: Do not install within 3' (0.9 m) of a heat

pump or an outdoor condensing unit. Strong air intake from this type of equipment can disturb the combustion process and cause damage or personal injury.

PAGODA TOP INSTALLATION

F10646-1

Figure 2. Heater with Outdoor Stackless Top

4' (1.2 m) Minimum

4' (1.2 m)

Minimum

4' (1.2 m)

Minimum

3' (0.9 m) Minimum

10' (3 m) Minimum

Forced Air Inlet

Figure 3. Minimum Distances to Building Openings from

Where Flue Products Exit the Boiler

1' (0.3 m)

Minimum

Heaters must not be installed under an overhang of less than 3' (0.9 m) from the top of the heater. Three sides must be open in the area under the overhang. Roof water drainage must be diverted away from the heaters installed under overhangs with the use of gutters.

For U.S. installations, the point from where the ue products exit the heater must be a minimum of 4' (1.2 m) below, 4' (1.2 m) horizontally from, or 1' (0.3 m) above any door, window or gravity inlet into any building. The top surface of the heater shall be at least 3' (0.9 m) above any forced air inlet, or intake ducts located within 10' (3 m) horizontally.

For Canadian installations, pool heaters shall not be installed with the top of the vent assembly within 10' (3 m) below, or to either side, of any opening into the building. Refer to the latest revisions of CAN/CSA-B149.

A minimum of 6' (1.8 m) is required from the heater to an inside corner wall for proper outdoor venting.

For installations in Florida and Texas, that must comply with the Florida or Texas Building Code, follow the directions shown in Figure 5 for the installation of hurricane tie-down brackets for all models.

Indoor Heater Installation

The heater is also design-certied for indoor installation when equipped with the approved drafthood.

For Canada, indoor installation is restricted to an enclosure that is not occupied and does not directly communicate with an occupied area. Refer to the latest edition of CAN/ CSA-B149 for specic requirements. Locate heater as close as is practical to a chimney or gas vent. Heater must always be vented to the outside. See section "Vent Piping" on page 14 for details. Minimum allowable space is shown on the nameplate.

WARNING: Indoor heaters require a drafthood that

must be connected to a vent pipe and properly vented to the outside. Failure to follow this procedure can cause

re or fatal carbon monoxide poisoning.

Pagoda Top Installation

1. Insert tabs into keyhole (4 places). See Figure 4, detail A.

2. Snap tabs into keyholes so as not to pull out. See Figure 4, detail B.

DETAIL A DETAIL B

OUTDOOR TOP

(SHIPPED LOOSE WITH HEATER)

Figure 4. Outdoor Top Installation

FLORIDA AND TEXAS BUILDING CODES

WIND SPEED = 150 MPH, 3 SECOND GUST

Min. Edge

Model

in. (mm)

206A 20 (508)

266/266A 23 (584)

336A 26 (660)

399/406A 29 (737)

2" x 6" x 1/8" Pallet Anchor Bracket (4 Total) (Kit# 011636)

EXPOSURE = C

38"

(965 mm)

F10648

28"

(711 mm)

3" (76 mm)

Min. Conc.

Pad by others

Min. Edge

Distance

(152 mm)

(1)–1/4" x 1-3/4" S.S. Tapcon Bolt & Washer (Field-Supplied) Ea. Pallet Anchor Bracket Use hole closest to unit (4 total)

1/4" x 1-3/4" S.S. Tapcon Bolt and Washer (Field-Supplied) NOTE: Use hole closest to unit with washer overlapping edge of unit.

Distance

(152 mm)

3" (76 mm) Min. Conc.

Pad by others

TOH

F10646-2

(1)–1/4" x 1-3/4" S.S. Tapcon Bolt & Washer (Field-Supplied) Ea. Pallet Anchor Bracket Use hole closest to unit (4 total)

Figure 5. Hurricane Tie-Down Bracket Installation

Outdoor and Indoor Stacks

The outdoor and indoor stacks are optional equipment and do not come standard with the heater. Refer to installation instructions inside box for instructions on how to install outdoor/indoor stack.

Model Outdoor Stack Indoor Stack

206A 009834 009838

266/266A 009835 009839

336A 009836 009840

399/406A 009837 009841

Table D. Outdoor and Indoor Stack Kit Number

OUTDOOR STACK KIT

(1) Outdoor, painted

(1) Adapter plate

(3) Mounting brackets (clips)

(1) Top panel cover

(2) 1-foot sections of metal tape

(3) Screws

(1) Instructions

Clips

Combustion and Ventilation Air

Indoor Units Only

The heater must have both combustion and ventilation air. The minimum requirements are listed in the latest edition of the National Fuel Gas Code (U.S. ANSI Z223.1 or Canada CAN/CSA-B149) and any local codes that may have jurisdiction. The most common approach is the "2-opening" method, with combustion air opening no more than 12" from the floor and the ventilation opening no more than 12" from the ceiling. For opening sizes using this method, see below.

All Air from Inside the Building:

Each opening shall have a minimum net free area as noted:

Model Sq. in. (m2)

206A 200 (0.13)

266/266A 266 (0.17)

336A 333 (0.21)

399/406A 399 (0.26)

Table E. Opening Minimum Net Free Requirements -

Indoor Air

All Air from Outdoors:

When air is supplied directly from outside the building, each opening shall have a minimum net free area as noted:

Figure 6. Outdoor Stack Kit Components

NOTE: The outdoor drafthood kit does not require any additional vent pipe for proper operation. This drafthood functions as the vent termination.

INDOOR STACK KIT

(1) Drafthood, unpainted

(1) Adapter plate

(3) Mounting brackets (clips)

(3) Screws

(1) Instructions

Clips

Figure 7. Indoor Stack Kit Components

Model

206A 50 (0.03) 75 (0.05) 100 (0.06)

266/266A 67 (0.04) 101 (0.06) 134 (0.09)

336A 84 (0.05) 126 (0.08) 168 (0.11)

399/406A 100 (0.06) 150 (0.1) 200 (0.13)

Table F. Opening Minimum Net Free Requirements -

CAUTION: Combustion air must not be contaminated

by corrosive chemical fumes which can damage the heater. Such damage will not be covered by the warranty.

Unrestricted

Opening

sq. in. (m2)

Outdoor Air

Typical Screened or

Louvered Opening

sq. in. (m2)

Typical Screened

and Louvered

Opening

sq. in. (m2)

Specications and Dimensions

F10646-4

Amp Draw

120 VAC, 1Ph, 60Hz 240 VAC, 1Ph, 60Hz

4 2

Indoor

Drafthood

38”

(965 mm)

13-1/4”

(337 mm)

gas

connection

Figure 8. Front View

Flue

10"

28"

(254 mm)

8-7/8"

(225 mm)

6-5/8" ASME

(168 mm ASME)

40"

(1016 mm)

Stackless

Outdoor Top

26-5/8”

(676 mm)

28-5/8” ASME

(727 mm ASME)

F10646

32-11/16"

(830 mm) Electrical

Connection

4-3/8"

(111 mm)

(3-3/8" ASME)

(86 mm ASME)

(711 mm)

Figure 9. Side View

*Note: For outdoor stack, use J dimension in the following tables for appropriate size plus 6 inches (152 mm).

Shipping Weights

Standard

Heater

w/Stackless

Top

187 (85)

210 (95)

230

(104)

249

(113)

Heater

Mode

206A

266/266A

336A

399/406A

BTUH

Input (000)

(kw)

199.5

(58.4)

266.0 (77.9)

332.5 (97.4)

399

(116.9)

Residential - Copper Heat Exchanger

(A)

Cabinet

Width

in. (mm)

(508)

(584)

(660)

(737)

(B)

Flue

Dia.

in. (mm)

(152)

(178)

(203)

(229)

(C)

Indoor

Drafthood

in. (mm)

61-5/8 (1565)

(1575)

(1600)

64-9/16

(1640)

in. (mm)

10.0

(254)

11.5

(292)

(330)

14.5

(368)

(D)

(J)*

in. (mm)

11-3/4

(298)

(279)

10-5/8

(270)

12-1/8

(309)

Gas

Conn.

in.

3/4 2

Water Conn.

in.

Table G. Residential - Copper Heater Specications and Dimensions

lbs (kg)

Indoor

Draft-

hood

(6.4)

(7.3)

(8.6)

(9.5)

Residential - Cupronickel Heat Exchanger

Shipping Weights

lbs (kg)

Heater

Mode

P-_206A-EN-X

P-_266A-EN-X

P-_336A-EN-X

P-_406A-EN-X

Heater

Mode

BTUH

Input (000)

(kw)

180.0 (52.7)

240.0 (70.3)

300.0 (87.9)

360.0

(105.5)

Table H. Residential - Cupronickel Heater Specication and Dimensions

Commercial - ASME Copper or Cupronickel Heat Exchanger

BTUH

Input

(000)

(kw)

(A)

Cabinet

Width

in. (mm)

(508)

(584)

(660)

(737)

(A)

Cabinet

Width

in. (mm)

(B)

Flue

Dia.

in. (mm)

(152)

(178)

(203)

(229)

(B)

Flue

Dia.

in. (mm)

(C)

Indoor

Drafthood

in. (mm)

61-5/8 (1565)

(1575)

(1600)

64-9/16

(1640)

(C)

Indoor

Drafthood

in. (mm)

(D)

in.

(mm)

10.0

(254)

11.5

(292)

(330)

14.5

(368)

(D)

in.

(mm)

(J)*

in.

(mm)

11-3/4

(298)

(279)

10-5/8

(270)

12-1/8

(309)

(J)*

in.

(mm)

Gas

Conn.

in.

3/4 2

Gas

Conn.

in.

Water Conn.

in.

Water Conn.

in.

Standard

Heater

w/Stackless

Top

187 (85)

210 (95)

230

(104)

249

(113)

Shipping Weights

lbs (kg)

ASME

Heater

w/Stackless

Top

Indoor

Draft-

hood

(6.4)

(7.3)

(8.6)

(9.5)

Indoor

Draft-

hood

B-_206A-EN-(C or X)

B-_266A-EN-(C or X)

B-_336A-EN-(C or X)

B-_406A-EN-(C or X)

199.5 (58.4)

266.0 (77.9)

332.5 (97.4)

399

(116.9)

(508)

(584)

(660)

(737)

Table I. Commercial - Heater Specifications and Dimensions

(152)

(178)

(203)

(229)

61-5/8 (1565)

(1575)

(1600)

64-9/16

(1640)

10.0

(254)

11.5

(292)

(330)

14.5

(368)

11-3/4

(298)

(279)

10-5/8

(270)

12-1/8

(309)

3/4 2

206 (94)

229

(104)

249

(113)

268

(122)

(6.4)

(7.3)

(8.6)

(9.5)

Vent Piping

WARNING: Indoor heaters require a drafthood that

must be connected to a vent pipe and properly vented to the outside. Failure to follow this procedure can cause

re or fatal carbon monoxide poisoning.

Flue materials must be certied to CATEGORY I or better. Type “B” double-wall or equivalent vent pipe is recommended. A draft of -0.01" to -0.08" WC must be maintained. However single-wall metal vent pipe may be used as specied in the latest edition of the National Flue Gas Code, ANSI Z223.1 (Canada - CAN/CSA-B149).

When properly installed outdoors, only the outdoor stackless top (provided) is required. If installed indoors, a drafthood is required, connected to a CATEGORY I (a heater that operates with a non-positive vent static pressure and a vent gas temperature that avoids excessive condensate production in the vent.) vent per the National Fuel Gas Code and local requirements.

Vent piping the same size as the drafthood outlet is recommended, however, when the total vent height is at least 10 ft (3 m) (drafthood relief opening to vent terminal), the vent pipe size may be reduced by no more than one (1) size as specied in Chapter 13 of the National Fuel Gas Code, ANSI Z223.1 (Canada - CAN/CSA-B149).

As much as possible, avoid long horizontal runs of vent pipe and too many elbows. If installation requires horizontal runs, the vent pipe must have a minimum of 1/4 in. per ft rise (20.8 mm per meter rise) and should be supported at not more than ve foot (1.5 m) intervals.

Plumber's tape, criss-crossed, will serve to space both horizontal and vertical piping. Gas vents supported only by the ashing and extending above the roof more than 5 ft (1.5 m) should be securely guyed or braced to withstand snow and wind loads. We recommend use of insulated vent pipe spacers through the roof and walls.

D-2 Power Vent Kit

Another option for an installation that requires horizontal runs is the D-2 power vent kit option.

Model 120 VAC P/N 240 VAC P/N

206A 010744 009832

266/266A 010744 009832

336A 010745 009833

399/406A 010745 009833

Table J. Power Vent Kit Part Numbers

NOTE: The D-2 Power Vent operates with a positive vent static pressure and with a vent gas temperature that prevents excessive condensate production in the vent, and as such, is a CATEGORY III appliance. For more information consult the D-2 Power Vent manual, Catalog no. 6000.57.1. CATEGORY I vent material such as B-vent must not be used under CATEGORY III conditions.

For protection against rain or blockage by snow, the vent pipe must terminate with a vent cap which complies with the local codes or, in the absence of such codes, to the latest edition of the National Fuel Gas Code, ANSI Z223.1 (Canada - CAN/CSA-B149).

The discharge opening must be a minimum of 2' (0.6 m) vertically from the roof surface and at least 2' (0.6 m) higher than any part of the building within 8' (2.4 m). Vent stack shall be at least 5' (1.5 m) in vertical height above the drafthood outlet. The vent cap location shall have a minimum clearance of 4' (1.2 m) horizontally from, and in no case below, unless a 4' (1.2 m) horizontal distance is maintained, from electric meters, gas meters, regulators and relief equipment.

The weight of the vent stack or chimney must not rest on the heater drafthood. Support must be provided in compliance with applicable codes. The heater top and drafthood must be readily removable for maintenance and inspection. Vent pipe should be adequately supported to maintain proper clearances from combustible construction.

Figure 10. D-2 Power Vent Option

The power vent system is a fan-assisted vent system designed for use on models 206A-406A.

The power vent system, when installed as directed, is capable of operating in applications such as through-thewall venting with reduced horizontal and vertical vent pipe sizes in new and current installations. The unit is factorywired for 240 VAC, with capability of eld-rewiring for 120

VAC.

For more information consult the D-2 Power Vent manual, (Catalog No. 6000.57.1).

2' MIN

8' (2.4 m)

MANUAL SHUT-OFF VALVE (Field supplied)

(76 mm)

(0.6 m)

OR LESS

VENT PIPE

DRAFT HOOD

VENT CAP

2' MIN

(0.6 m)

5' MIN

(1.5 m)

Gas piping must have a sediment trap ahead of the heater gas controls, and a manual shut-o󰀨 valve located outside the heater jacket. All gas piping should be tested after installation in accordance with local codes.

CAUTION: The heater and its manual shut-o󰀨 valve

must be disconnected from the gas supply during any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa). Dissipate test pressure in the gas supply line before reconnecting the heater and

its manual shut o󰀨 valve to gas supply line. FAILURE

TO FOLLOW THIS PROCEDURE MAY DAMAGE THE GAS VALVE. OVER PRESSURIZED GAS VALVES ARE NOT COVERED BY WARRANTY. The heater and its gas connections shall be leak tested before placing the appliance in operation. Use soapy water for leak test. DO

NOT use open ame.

Supply Pressure

CAUTION: Do not use teon tape on gas line pipe

thread. Only sealant tape or a pipe compound rated for use with natural and propane gases is recommended. Apply sparingly only on male pipe ends, leaving the two end threads bare.

Figure 11. Venting Clearances

NOTE: With venting application of two or more heaters, contact the factory.

Gas Supply Connections

3" MIN

Typical

HEATER

GAS INLET

FINISH FLANGE

UNION

(Field supplied)

SEDIMENT TRAP (Field supplied)

HEATER JACKET

GAS VALVE

A minimum of 6 in. WC and a maximum of 10.5 in. WC upstream pressure under load and no-load conditions must be provided for natural gas. A minimum of 12 in. WC and a maximum of 13 in. WC are required for propane gas under load and no-load conditions.

Gas Pressure Regulator

The gas pressure regulator is preset at 4.0 in. WC for natural gas, and 10.5 in. WC. for propane gas. The pressure at the gas valve, taken with a manometer, should be about 4.0 in. WC natural gas and 10.5 in. WC propane gas. If an adjustment is needed, remove seal and turn adjustment screw clockwise counter-clockwise

MANUAL

SHUT-OFF

VALV E

UNION

to decrease pressure.

to increase pressure or

Figure 12. Gas Supply Plumbing

F10640-2

Figure 13. Manual Shut-O󰀨 Valve Installation

Gas Pressure Adjustment Locations

Millivolt Gas Valve

GAS PRESSURE ADJUSTMENT

Figure 14. Robertshaw 7000 (Heater Models 206A - 406A)

Electronic Ignition Gas Valves

GAS PRESSURE ADJUSTMENT

Figure 15. Honeywell VR8340 (Heater Models 206A - 406A)

GAS PRESSURE ADJUSTMENT

Figure 17. Robertshaw 7000 BDER (Heater Models 266A -

336A)

GAS PRESSURE ADJUSTMENT

Figure 16. Robertshaw 7200 (Heater Model 206A)

Figure 18. Robertshaw 7000 DERHC (Heater Model 406A)

Pipe Sizing for Gas Connection

F10638-1

These capacities shown below based on using SCH 40 black iron pipe. For capacities using other materials, consult local code.

Maximum Equivalent Pipe Length (ft) (m)

360

210

140

0.60

1.53

480

(146.3)

320

(97.5)

225

(68.6)

N P

445

(135.6)

290

(88.4)

215

(65.5)

480

(146.3)

Natural Gas 1000 BTU/FT

Specic Gravity @ 0.5 in WC Pressure Drop

Propane Gas 2500 BTU/FT

Specic Gravity @ 0.5 in WC Pressure Drop

3/4" 1" 1-1/4" 1-1/2"

Model

N P N P N P

206A

266/266A

336A

399/406A *

* A 3/4" gas line can be used for up to 5' (1.5 m) maximum length from the gas valve in addition to the sediment trap.

(7.6)

(4.6)

(3.0)

(18.3)

(10.7)

(6.1)

(4.6)

(27.4)

(15.2)

(9.1)

(6.1)

215

(65.5)

125

(38.1)

(24.4)

(16.8)

(109.7)

(64.0)

(42.7)

(29.0)

Table K. Gas Pipe Sizing

Flow Rate

Model Pipe Size Min. GPM (lpm)

206A 1-1/4"–1-1/2"–2" 20 (75) 125 (473)

266/266A 1-1/4"–1-1/2"–2" 25 (95) 125 (473)

336A 1-1/4"–1-1/2"–2" 35 (132) 125 (473)

399/406A 1-1/4"–1-1/2"–2" 40 (151) 125 (473)

* When ow rates exceed maximum GPM an external auxiliary bypass valve is required. See external bypass valve section for details.

Table L. Min/Max Flow Rates

Max. GPM

(lpm)

F10637-1

Figure 20. Brass Header (ASME) Water Flow

Flow GPM

(lpm)

Pressure Drop (Ft. of Head) (m of Head)

206A 266/266A 336A 399/406A

20 (75) 4.0 (1.2)

25 (95) 4.0 (1.2) 4.6 (1.4)

30 (113) 4.0 (1.2) 5.2 (1.6)

35(132) 4.0 (1.2) 5.8 (1.8) 5.2 (1.6)

40 (151) 4.6 (1.4) 5.8 (1.8) 5.2 (1.6) 5.2 (1.6)

50 (189) 4.6 (1.4) 6.3 (1.9) 6.9 (2.1) 6.9 (2.1)

60 (227) 4.6 (1.4) 6.9 (2.1) 6.9 (2.1) 6.9 (2.1)

70 (265) 4.6 (1.4) 8.1 (2.5) 9.2 (2.8) 9.2 (2.8)

80 (303) 4.6 (1.4) 9.2 (2.8) 9.8 (3.0) 9.8 (3.0)

90 (340) 6.9 (2.1) 10.4 (3.2) 10.4 (3.2) 10.4 (3.2)

100 (378) 8.1 (2.5) 11.0 (3.4) 12.1 (3.7) 12.1 (3.7)

110 (416) 10.4 (3.2) 11.5 (3.5) 13.3 (4.0) 13.3 (4.0)

120 (454) 11.0 (3.4) 12.7 (3.9) 17.9 (5.4) 17.9 (5.4)

125 (473) 11.5 (3.5) 13.8 (4.2) 20.2 (6.2) 20.2 (6.2)

Table M. Polymer Heat Exchanger Pressure Drop -

Residential Models - (UG Fully Open)

Figure 19. Polymer Header Water Flow

O-RING

F10715

Flow GPM

(lpm)

Pressure Drop (Ft. of Head) (m of Head)

206A 266A 336A 406A

20 (75) 8.2

30 (113) 9.5 9.5

40 (151) 9.7 9.7 11 13.4

50 (189) 10 9.8 12.2 13.4

60 (227) 11 10.4 13.7 13.5

70 (265) 11.5 10.9 14.3 14

80 (303) 12.6 12 15.5 15

90 (340) 14 13 16.2 16.2

100 (378) 15 14.2 17.5 16.7

HEADER

PROTEK SHIELD ASSEMBLY

Figure 22. Inlet/Outlet Header – Brass

HEADER FLANGE (CPVC)

HEADER FLANGE NUT

(CPVC)

PLUMBING

F10664

Table N. Brass Heat Exchanger Pressure Drop - ASME

Models (UG Closed)

NOTE: Table capacity is based on schedule 40 black iron pipe. For capacity using other material, consult local codes.

Polymer Headers (Residential Models)

Before attaching the 2-inch unions to the inlet/outlet header, make sure the O-rings are properly seated in the grooves. Use Aqualube or equivalent non-petroleumbased lubricant on the O-ring. Hand tighten the unions. Glue PVC piping directly to the unions.

O-RING

HEADER FLANGE (CPVC)

PLUMBING

PROTEK SHIELD ASSY

HEADER FLANGE NUT (CPVC)

F10641

NOTE: Some jurisdictions require the addition of a ow switch on ASME installations. Kit # 015889F for ange

connection or 015890F for NPT connection can be ordered that will allow a standard ASME unit to comply with the code requirements.

ProTek Shield Assembly

This heater is equipped with a ProTek Shield Assembly (located under the inlet connection on polymer headers) and in the ProTek Shield Adapter assembly shipped loose in the accessory carton for eld installation on brass ASME headers.

NOTE: ProTek Shield not available on ASME models until March 2020.

This component provides protection to the heat exchanger against galvanic corrosion, when properly bonded to the heat exchanger. It should be replaced when the weight of the ProTek Shield is reduced to about 40% of the original weight (1.46 #).

Figure 21. Inlet/Outlet Header – Polymer

High temperature CPVC header anges and header ange nuts are provided. If there is any possibility of backsiphoning when the pump stops, it is suggested that a check valve (or valves) also be installed in the system.

Brass Headers (ASME Models)

Heater must be located so that any water leaks will not damage the structure of adjacent area. Before attaching the ProTek Shield Adapter to the inlet connection and the 2-inch unions, make sure the O-rings are properly seated in the grooves. Use Aqualube or equivalent non-petroleumbased lubricant on the O-ring. Hand tighten the unions. Glue PVC piping directly to the unions.

Figure 23. ProTek Shield Assembly

CAUTION: STOP the pool pump before attempting to

remove ProTek Shield Assy. Failure to do so may result in damage to ProTek Shield Assy, loss of pool water, or personal injury.

CAUTION: Do not use tools to remove (twist) the ProTek Shield Assy or the wing nut on the stud of the ProTek Shield Assy. Non-warrantable damage may occur.

Follow the steps below to replace the ProTek Shield Assy:

F10642-2

1. Shut off the pool pump and bleed pressure from the system.

2. Close isolation valves to minimize pool/spa water loss.

3. Remove wing nut from bottom stud on ProTek Shield Assy.

4. Remove bonding wire ring terminal from stud.

5. Rotate ProTek Shield Assy clockwise (by hand) to unscrew it from the assembly.

6. Inspect/replace as necessary and reverse above procedure to reinstall. Hand tighten only! Do not use tools.

Internal Automatic Bypass Valve

In addition to the Unitherm Governor, a built-in automatic bypass valve is provided in the In/Out header. While the Unitherm Governor responds to the changes in water temperature in the heater, the internal bypass valve automatically responds to changes in water pressure in the piping system. Proper amount of water ow is maintained through the heater under varying pressures dictated by the conditions of the pump and lter.

UG/BYPASS ASSY

NOTE: Make sure the O-ring is properly seated in the O-ring groove before installation.

Unitherm Governor Operation

CAUTION: The patented Unitherm Governor is

a thermostatic mixing valve specically designed to

maintain constant heater internal temperature between 105°F (41°C) and 115°F (46°C) despite continually

changing ow rates from the lter and changing pool

temperatures. This narrow range is needed to prevent damaging condensation on the burners which will occur if the heater runs for any length of time below 100°F (38°C). It is also needed to inhibit scale formation in the tubes by maintaining temperatures well below accelerated scaling temperatures.

UG PLUG

UNITHERM GOVERNOR

GASKET

F10725

Figure 24. Unitherm Governor - Polymer

UG/BYPASS ASSY

BYPASS DISC

SPRING "YELLOW" - 206/266 "GREEN" - 336/406

F10642-3

Figure 26. Internal Automatic Bypass Valve - Brass

NOTE: The Unitherm Governor and Bypass Valve Assy are not individually replaced components on ASME units. If either needs to be replaced, the entire UG/ Bypass assy must be replaced. The "yellow" spring is used on models 206A, 266A. The "green" spring is used on models 336A, 406A.

External Auxiliary Bypass Valve

Where Required - An auxiliary bypass valve should be

used when ow rates exceed 125 GPM (473 lpm). Usually a high-performance pump size larger than two horsepower will exceed this ow rate. This valve is required to complement the function of the automatic bypass valve, particularly when starting the heater in winter or early spring when the spa or pool temperature is below 50°F (10°C). It also serves to eliminate needless pressure drop through the heater and accompanying reduction in the ow rate to the spa jets, etc.

FROM HEATER

TO HEATER

UNITHERM GOVERNOR

Figure 25. Unitherm Governor - Brass

FULL PORT

BALL VALVE

OR GLOBE

VALV E

TO POOL/SPA

BYPASS VALVE

Do not use gate valve.

Figure 27. Auxiliary Bypass Valve

FROM POOL/SPA

Auxiliary Bypass Valve Adjustment

To set bypass, with clean lter, adjustment is made by feeling the inlet and outlet pipes at the heater. Outlet pipes should be slightly warmer than inlet and comfortable to the touch. If pipe is hot, close bypass; if cold, open bypass.

Pressure Relief Valve Installation

To conform to local building codes, it may be necessary to install a pressure relief valve. A 3/4" pressure relief valve, having a capacity equal to or greater than to the BTU output of the model to be installed, is recommended for this heater.

A 3/4" NPT connection is provided in the Polymer header for installation of a pressure relief valve. The valve shall be installed in a vertical position. Do not over-tighten. Install pressure relief valve hand tight plus 1/2 turn.

PRESSURE RELIEF VALVE

PRV DISCHARGE CONNECTION

NOTE: To avoid water damage or scalding due to valve operation, drain pipe must be connected to valve outlet and run to a safe place of discharge. Drain pipe must be the same size as the valve discharge connection throughout its entire length and must pitch downward

from the valve. No shut-o󰀨 valve shall be installed

between the relief valve and the drain line. Valve lever should be tripped at least once a year to ensure that waterways are clear.

The heater requires water ow and positive pressure to re and operate properly. It must therefore be installed downstream of the discharge side of the lter pump. See Figure 31 and Figure 32. A typical installation is plumbed as follows:

1. The inlet side of the filter is plumbed directly to the discharge side of the filter pump;

2. The outlet side of the filter is then plumbed to the inlet of the heater; and

3. The outlet of the heater is plumbed to the return line to the pool or spa. The pump, filter and heater are thus plumbed in series (Salt generators and chemical feeders must be downstream of the pool heater).

Plumbing from the heater back to the pool or spa must not have any valves or restriction that could prevent ow when the pump is operating.

IN/OUT HEADER

F10662

Figure 28. Field-Supplied Pressure Relief Valve Polymer

Header (Residential Units)

A 3/4" NPT connection is provided in the header for installation of a 75 PSI (517 kPa) pressure relief valve. The PRV is shipped loose in the accessory carton with the pagoda top. The pressure relief valve shall be installed in a vertical position.

F10663

PRESSURE RELIEF VALVE

CAUTION: An additional source of heated water,

e.g. a solar system, must be connected to the main line ahead of the heater inlet pipe in order for it to act as the primary heat source. If the primary system provides adequate heat to maintain setpoint, the heater will not

re. Be advised that the control panel will then display

sensed water temperatures downstream of the primary heating system, rather than the temperature of the water exiting the pool.

Heater must be located so that any water leaks will not damage the structure of adjacent area. PVC pipe may be glued directly into the headers unions.

Heat Exchanger Reversal

Procedure for Residential Models

1. Remove right and left side access panels. See

Figure 30.

Figure 29. Pressure Relief Valve Brass Header (ASME

Models)

F10652

Figure 30. Access Panels

Plumbing Diagrams

TO REPACE AN ENGINEERED PIPING SYSTEM BY A PROFESSIONAL ENGINEER

Water Connection

THIS DIAGRAM IS A RECOMMENDATION AND IS NOT INTENDED

Figure 31. Single Pool Heater Installation

ISOLATION VALVE

BALL VALVE

PRESSURE RELIEF VALVE

PUMP

UNION

CHECK VALVE

THIS DIAGRAM IS A RECOMMENDATION AND IS NOT INTENDED

TO REPACE AN ENGINEERED PIPING SYSTEM BY A PROFESSIONAL ENGINEER

Figure 32. Multiple Pool Heater Installation

2. Disconnect wires at high limit, AGS (automatic gas

F10667

shut-off), water pressure switch on the in/out header and ProTek Shield bonding wire. See Figure 33.

F10653

Figure 33. Component Wiring Locations - In/out Header

3. Digital Models: Remove the thermostat temperature

sensor by loosening the compression fitting nut. Reroute the sensor to left side of the heater. See Figure 34.

Millivolt Models: Remove the temperature sensor bulb and retainer clip by loosening the compression fitting nut. Re-route the sensor bulb to the left side of the heater. See Figure 35.

5. Reconnect high limit, AGS, water pressure switch wires, and ProTek Shield bonding wire.

6. Digital Models: Insert the temperature sensor into the compression fitting, so that the sensor is flush with the top of the fitting. Tighten 1/2 turn past hand tight.

Millivolt Models: Insert sensor bulb and retainer clip into sensor well.

7. Allow for water flow through the heater and check for leaks.

8. Re-attach access panels to the opposite sides.

For instructions on reversing the heat exchanger connections on ASME models, call your factory representative.

5. ELECTRICAL WIRING

NOTE: If it is necessary to replace any of the original wiring, use 105°C wire or its equivalent, and/or 150°C wire or its equivalent, like the original wiring.

WARNING: Digital heaters are factory-wired for

240 VAC, 1 Ph, 60 Hz power supply. DO NOT attempt to operate at 208 VAC.

F10654

Figure 34. Digital Temperature Sensor Location

Figure 35. Millivolt Temperature Sensor Location

4. Remove (12) nuts holding the inlet/outlet and return headers to the tube sheets. Clean off tube sheet area where the gasket seats. Also clean off the header and the gasket. Apply a non-petroleum-based lubricant to the gasket such as Aqualube. Re-attach the headers to the opposite sides, making sure they are installed in an upright position. Do not over-tighten. Torque should not exceed 7 ft/lb. See Figure 34.

Millivolt Models ("M" su󰀩x)

The Millivolt models are equipped with a self-generating electrical system in which the electrical current is provided by a pilot generator. No external electrical connections are required.

When installing a remote switch, do not exceed 10 ft (3 m) of wiring from the heater. Use 18-gauge stranded wire.

Digital Models ("E" su󰀩x)

The standard eld-wiring connection is on the right side of the heater.

To wire the heater from the left side, follow these steps:

1. Remove the two (2) screws that hold the front door to the heater. Remove and set aside door for better access to wiring.

2. Remove the four (4) screws that hold down the junction box to the sway brace.

3. Remove the transformer cover located on the far right by removing one (1) screw.

4. Remove the two (2) screws that hold down the transformer.

5. Remove the one (1) screw that holds down the ground wires.

6. Disconnect P6 connector from PC board.

7. Remove transformer from its current location and relocate it on the far left side of the heater.

8. Re-route all high-voltage wires and ground wires

(FACTORY MOUNTED

RED

HOT

WHITE

through the left jacket side of heater.

9. Re-install P6 connector, ground wires (SPG), transformer, junction box, front door, and plug right side with the left side’s grommet plug.

NOTE: 7/8" diameter holes not utilized on jacket and

control box can be used for reman switch, auxiliary

control interface or power vent (D-2) wiring.

Electrical Power Draw

CAUTION: Heater must be electrically grounded and

bonded. Bonding lug is provided loose with the heater. Install bonding lug on lower right or left side of jacket as necessary for bonding the heater. Mounting hole is provided on the jacket.

NOTE: Failure to ground the heater electrically could

a󰀨ect the heater’s electronics.

NOTE: See "Time Clock/Fireman’s Switch" on page 31

for further instructions if using a time clock/reman’s

switch.

There should be no connection to the red wire for 120 VAC operation. Attach a wire nut to the red wire.

BLACK

RETURN

SUPPLY

NEUTRAL

SIDE

GROUND

Figure 37. 120 VAC Wire Connection

BLACK

WHITEWHITE

GREENGREEN

HEAT ER 4 WIRES

240 VAC Wiring

For 240 VAC input power to the unit, connect the black wire to the “L1” or hot leg of the power supply. Connect the red wire to the L2 or second hot leg of the power supply.

There should be no connection to the white wire for 240 VAC operation. Attach a wire nut to the white wire.

WARNING: DO NOT attempt to operate the heater

at 208 VAC.

The Electronic Intermittent Ignition Device automatically lights the pilot and main burners upon a call for heat. The heater is supplied with a dual-voltage transformer for 120 VAC or 240 VAC input power hookup.

When operating on 120 VAC power, units draw 4 amps. When operating on 240 VAC power, units draw 2 amps.

OPTION LOCATION LEFT SIDE FIELD WIRING

BONDING LUG (OPTIONAL LOCATION)

Figure 36. Heater Wiring Locations

Transformer Wiring

120 VAC Wiring

F10650

CONTROL BOX

LOCATION)

SWAY BRACE

BONDING LUG (STANDARD LOCATION)

For 120 VAC input power to the unit, connect the black wire to the L1 or hot leg of the power supply. Connect the white wire to the “Ret” or neutral leg of the power supply.

SUPPLY

SIDE

BLACK

HOT

REDRED

BLACK

GREENGREEN

HEAT ER 4 WIRES

Figure 38. 240 VAC Wire Connection

Heater must be electrically grounded and bonded in accordance with local codes, or, in the absence of local codes, with the latest edition of the National Electrical Code, ANSI/NFPA 70. (Canada - Canadian Electrical Code, CSA C22.1, Part 1 and Part 2.)

CAUTION: If the transformer’s primary side is wired

for 120 VAC and 240 VAC is applied, damage to the transformer and PC board may result. Such damages are not covered under manufacturer’s limited warranty.

NOTE: Input power to the heater (120 or 240 VAC) can

be supplied from the load (pump) side of time clock or directly from the GFCI power source. It is preferred

that full-time power be supplied to the heater from the GFCI power source, and that the heater be

controlled by the reman’s switch connection or

using a two or three-wire remote. If using a switched GFCI power source, the heater could display false service indicators on the display panel if the pump is turned o󰀨.

6. WIRING DIAGRAM - MILLIVOLT

7. WIRING DIAGRAM - DIGITAL

8. CONTROLS

KNURLED

CONTROL BEZEL

PRESSURE SWITCH TEMP SENSOR HL1 - HIGH LIMIT HL2 - HIGH LIMIT

UNITHERM GOVERNOR

NOTE: Caution must be used to not damage controls or wiring.

SCREW

F10646-5

Figure 41. Knurled Screw Location

ROLL-OUT SWITCH

GAS VALV E

F10640-2

Figure 39. Location of Controls (View One)

PROTEK SHIELD ASSY

Control Adjustments Millivolt Models

The water temperature is controlled by the heater thermostat on the upper front panel of the heater. The control center contains an On/O󰀨 switch and one thermostat.

The thermostat is tted with a means of limiting the upper temperature just below the maximum level. The knob stop adjustment ring illustrated below is adjustable by loosening the set screw, rotating the knob stop ring to the desired location and re-tightening the set screw.

SPA TEMPERATURE RANGE

POOL TEMPERATURE RANGE

DRAIN PLUG IN REAR HEADER

F10640-3

PILOT

Figure 40. Location of Controls (View Two)

Control Panel Removal

1. Remove screw from front door. Set aside door for serviceability.

2. Remove (4) screws from sides of control panel.

3. Rotate control panel down until panel stops. Do not force.

KNOB STOP RING

SET SCREW

KNOB STOP SHOWN ABOVE IS IN THE SPA TEMPERATURE RANGE.

STAND-BY TEMPERATURE

Figure 42. Control Adjustment – Millivolt Models

Control Adjustments – Digital Models

Program Mode Button (SW1)

The pool heater touchpad, located on the upper front panel of the heater, allows the user to select either POOL or SPA operation, and to adjust the setpoint temperature. The LCD display window indicates the mode (OFF, SPA, POOL) and the actual water temperature. A manual power switch provided below the touchpad turns the control power ON or OFF. See Figure 43.

TEMP ADJUST BUTTONS

MODE BUTTON

Figure 45. Thermostat Program Button (SW1)

TEMP

LCD DISPLAY

Figure 43. Control Adjustment – Digital Models

MODE

ON OFF

Mode Button

The MODE button is used to select POOL or SPA operation. It also allows the user to turn the heater o󰀨 electronically, allowing the LCD to remain energized and to continue showing the actual water temperature.

Temp Buttons

If the heater is in POOL or SPA mode, the desired water temperature (SETPOINT) will be displayed and may be adjusted using the UP or DOWN buttons.

Operation

In the POOL or SPA modes, the actual water temperature is displayed along with the desired water temperature (SETPOINT). When the water temperature is above the setpoint, “Water Temp” will alternate with “No Demand.” When the water temperature is below the setpoint and the heater is ring, “Water Temp” will alternate with “Heating.”

To adjust the setpoint temperature, make sure the control is in the appropriate mode (POOL or SPA) and push the UP or DOWN buttons.

By default, the setpoint range is 50-104°F (10-40°C). See MAX Settings on page 28 to increase the MAX setting, if necessary.

Service Menu and Fault History

To access the Service Menu and fault history, press the Mode and UP buttons simultaneously for 3 to 5 seconds. The heater will continue to operate while in the Service Menu. The rst screen displayed is the Flame Strength indicator, which indicates the pilot ame current using a bar graph and numerical display. A signal of less than 4 bars indicates a weak ame signal and may require service. Refer to the Troubleshooting section for possible causes and corrections.

Figure 46. Flame Strength Indicator

Press the DOWN button. The Supply Voltage screen indicates the voltage supplied to the control board. Normal readings range from 24 to 29 volts.

Figure 47. Supply Voltage Indicator

Press the DOWN button. The Run Time indicates the total hours of operation for the pool heater, as measured by the amount of time that the main gas valve has been powered. The Cycle count indicates the number of on/o󰀨 cycles of the heater, as measured by the number of times the pilot valve has been powered.

Figure 44. Alternating Display During Heating

Figure 48. Run Time/Cycles

Press the DOWN button. The Fault History displays up to ten faults in memory. The order of the faults begins with “Fault Last,” which is the most recent fault, and proceeds through ten most recent messages in chronological order. The second line of the display shows the fault message. If there are no faults in the history bu󰀨er, the second line reads “All Faults Clear.”

Both the POOL and SPA setpoints will revert to 65°F (18°C) and both POOL and SPA maximum temperature settings will be 104°F (40°C). The CONTROL LOCKOUT PIN will be cleared and the control will resume normal operation.

Clear Faults

Refer to step one above to access the program screen. Press the MODE button until CLEAR FAULTS appears on the digital display. Press and hold both UP and DOWN buttons for 5-7 seconds until FAULTS CLEARED appears. This operation resets the Fault History le to “0” and clears all the stored faults.

Figure 49. Fault History Indicator

Program Button

1. Remove the four screws holding the control cover, and swing the panel down so the back side of the board is visible. Locate the Program Mode button (SW1). See Figure 45. Press and hold the button for 5-7 seconds until SET FACTORY DEFAULTS appears on the display. Release the program button.

2. Press the MODE button sequentially until the desired program event is reached. There are 5 different events that can be programmed. They appear in the sequence listed in Figure 50.

Resets board to factory default settings.

Resets faults in the History File.

Change from Fahrenheit to Celsius.

SPA setpoint maximum adjustment.

POOL setpoint maximum adjustment.

Figure 50. Programmable Events

Set Factory Defaults

Refer to step one above to access the program screen. SET FACTORY DEFAULT should appear on the screen. If it does not, press the MODE button until it appears on the digital display. Press and hold both UP and DOWN buttons for 5-7 seconds until DEFAULT SET appears. This operation resets the operating program to its factory default values.

Fahrenheit or Celsius

Refer to step one above to access the program screen. Press the MODE button until FAHRENHEIT or CELSIUS appears on the digital display. The UP or DOWN buttons will select FAHRENHEIT or CELSIUS on the temperature display. Choose the desired temperature scale.

Spa Max Temp – Spa Setpoint Maximum Adjustment

Refer to step one above to access the program screen. Press the MODE button until SPA MAX TEMP appears on the digital display. Using the UP and DOWN buttons will change the Maximum Temperature Setting to your desired value. The control can be set for a maximum of 107°F (42°C).

Pool Max Temp – Pool Setpoint Maximum Adjustment

Refer to step one above access into the program screen. Press the MODE button until POOL MAX TEMP appears on the digital display. Using the UP and DOWN buttons will change the Maximum Temperature Setting to your desired value. The control can be set for a maximum of 107°F (42°C).

Control Lockout

The heater is equipped with a Control Lockout feature to prevent unauthorized tampering or adjustment of the control settings. To lock out the controls, press the DOWN button and MODE button for 5 seconds. Choose a three digit PIN, using the UP and DOWN buttons to select the digits and the MODE button to lock in selections. Conrm your selection and record your PIN.

To unlock the controls, press any button to bring up the ENTER PIN menu. Enter the PIN that was used to lock the control. Note that power cycling will not clear the lockout. Successfully unlocking the control will display “LOCKOUT CLEARED.” Failure to enter the correct PIN will display “INVALID PIN.”

In the event that the user-selected PIN is lost or does not clear the Control Lockout, use the Program Button to SET FACTORY DEFAULTS. This will clear the PIN and allow normal operation and selection of a new PIN if desired.

NOTE: Both the POOL and SPA setpoints will revert back to 65°F (18°C) and the POOL and SPA maximum temperature settings will be 104°F (40°C). These setpoints will need to be readjusted to desired settings.

NOTE: The LCD temperature display may not agree with the temperature reading of your pool or spa thermometer. The heater reads the water temperature at the inlet. Due to the circulation characteristics of any pool or spa, the

water temperature at the inlet to the heater may di󰀨er

from that observed at a given location in the pool or spa.

Status and Diagnostics

The digital models are programmed to display a variety of status and diagnostic messages, depending on the operating conditions.

The following heat status messages are displayed in Pool, Spa, and Remote modes when there are no active fault conditions.

Display Condition

Heating Call for heat established, ame present.

Spark Spark operating.

No Demand Heat demand is satised.

Table O. Heater Status Messages - No Active Faults

The following conditions are displayed in Pool, Spa and Remote modes.

The following conditions are displayed only while there is a demand for heat present.

Display Condition

Water Sw Open Water pressure switch open.

Vent/Field Sw #1

Hi Limit 1 Fault High limit 1 open.

Hi Limit 2 Fault High limit 2 open.

Rollout Sw Open Rollout switch open.

Flow/Field SW #2

Ignition Lockout (Propane Tab Broken)

Ignition Failure (Propane Tab Not Broken)

Ign 6 min Delay (Propane Tab Not Broken)

Table Q. Heater Status Messages - Demand for Heat

Vent spill switch/eld switch #1 open.

Field-supplied ow switch/eld switch #2 open.

Alternating with “No pilot sensed”

- Pilot ame not established within the required time (15 sec or 90 sec).

Alternating with “Main Ign Failure”

- Pilot ame lost during the 8 second trial to ignite the main burner.

Alternating with “No pilot sensed”

- Pilot ame not established within 90 seconds.

Alternating with “Main Ign Failure”

- Pilot ame lost 4 times within the 8 second trial to ignite the main burner. Heater will lockout for 6 minutes before retrying.

Display Condition

Sensor Failure

Sensor Open

Sensor Short

Flame w/o CFH

PV Output Fault

MV Output Fault

LoNox Tab Fault

Internal Fault Board fault, replace board.

EEPROM Fault

Clock/Fireman Sw

Low Temp Lockout

Thermistor temperatures disagree by more than 2°F (1°C).

Thermistor sensor failed open. Below

-20°F (-29°C).

Thermistor sensor failed short. Above 217°F (103°C).

Board is sensing ame when both main and pilot valves are commanded shut.

Pilot gas valve output is not in commanded state.

Main gas valve output is not in commanded state.

Voltage is sensed at the Lo NOx terminal on a non -Lo- NOx heater (Lo NOx tab is intact).

Memory fault, reset set points, replace board if fault does not clear.

Time clock/reman switch circuit is open.

Water temperature below 36°F (2°C).

Table P. Heater Status Messages - Active Faults

Remote Control Installation and Operation

CAUTION: Before installing remote controls to

the digital heaters, read the following: The digital thermostat model is remote-ready in most cases. The digital liquid crystal display (LCD) shows the actual pool temperature, operating status, and service codes. See Figure 51. The touch pad on the control panel allows you to select the desired pool or spa temperature. It also indicates when a remote system is controlling the heater by displaying Remote in the display. When connecting the heater to a remote system, identify whether it is a two- or three-wire remote system. Select the appropriate instruction listed below to properly install the remote to the heater.

Remote Operation (Digital models only)

The heaters are equipped with the ability to work with external remote controls. The supplied 7-pin remote wiring connector supplies power out to either a toggle switch or the switch contacts of a third-party remote. The remote works by either making or breaking the circuit created by the remote wiring. Typically, a remote does not supply power to the heater, it only provides a switching function to turn the heater On or O󰀨. If your remote is supplying

its own voltage to the heater, it will not work with this heater and may damage the digital circuit board.

For operation of the heater using the onboard thermostatic controls with a time clock. See "Time Clock/Fireman’s

Switch" on page 31.

Millivolt models are not designed for operation with remote control sytem.

Activating the Remote

To activate or deactivate the remote function:

1. Press and hold the UP and DOWN arrow buttons for 3 to 5 seconds.

The second line of the display will alternate even when the unit is o󰀨 (“No Demand”).

NOTE: When in remote operation, the keypad mode and temp buttons are disabled.

Figure 52. Remote Control Menu - Activation

Remote Control Wiring Digital Models Only

ATTENTION

OBSERVE PRECAUTIONS

ELECTROSTATIC

SENSITIVE DEVICES

OFF Mode

Heating in the POOL Mode

Heating in the SPA Mode

Remote Mode

Figure 51. Remote Control Menu - Remote Operation

CAUTION: Electrostatic Discharge (ESD) damage

can be caused by direct or indirect contact with the wiring or circuit board. When one walks to the heater area, an electrostatic charge accumulates on the body.

Contact of a nger allows the body to discharge, possibly

causing device damage. This damage can be limited if the service person discharges himself, following ESD preventive/removal practices, and holds on to the heater enclosure for 5 seconds before proceeding.

Important Installation Notes for Remote or External

Wiring Conguration:

• Remote wiring must be run in a separate conduit.

• Remote wiring must not be run parallel to high voltage

lines.

• For runs of under 30' (9 m), remote wiring should have stranded conductors with a minimum of 22 AWG, 600V, cable twisting 1.5" to 2.5" (3.8 to 6.4 cm) lay and jacketed.

• For runs over 30' (9 m), the conductors should be a minimum of 20 AWG, 600V, cable twisting 1.5" to 2.5" (3.8 to 6.4 cm) lay that is shielded and jacketed.

• Maximum cable length is 200' (61 m).

• For both two- and three-wire remote systems, the provided 7-pin wiring connector must be utilized.

NOTE: The remote wires must be connected to the 7-pin connector before the connector is plugged into the board.

2-Wire Remote Control (On-O󰀨)

This application assumes that only one heating function (pool or spa) is required.

1. Turn on power to the heater.

2. For a 2-Wire Remote Control from a remote without its own sensor, push the MODE button to the “POOL” or “SPA” mode and set the desired setpoint (eg. 102 °F (39°C) for Spa).

3. For a 2-Wire Remote Control from a remote with its own sensor, push the MODE button “POOL” or “SPA” mode and set the temperature to the highest setting available on the control. The actual setpoint will be controlled by the remote control.

4. Turn the MODE button to “OFF” and remove power from the heater.

5. On the “Remote Interface Harness”, connect the BLUE wire to one side of the “REMOTE” switch and connect the other side to either the ORANGE/BLACK wire for “SPA” operation or the BLACK/ORANGE wire for “POOL” operation. See Figure 53.

3. Turn the MODE button to “OFF” and remove power from the heater.

BLU - 24VAC

ORN/BLK - To Spa (COMM)

Wire Nut BLK/ORN - To Pool (COMM)

Figure 54. 2-Wire Remote Harness Installation on the P8

Connector of the Board

Pool Common (BLK/ORN)

Spa Common (ORN/BLK)

24VAC HOT (BLU)

Figure 53. 7-Pin Remote Interface Harness

6. Attach wire nut on unused wire to the “Remote Interface Harness.”

7. Install the “7-Pin Remote Interface Harness” to the P8 connector and turn power “ON” to the heater. See Figure 54.

For activation of the remote control, see section on page

30.

3-Wire Remote Control Using Three-

Position Switch (Pool-O󰀨-Spa, or Low-O󰀨-

High)

This application assumes that both heating functions (pool and spa) are required.

1. Turn on power to the heater.

2. Push the MODE button to the “POOL” or “SPA” mode and set the desired temperature for each (eg. 80°F (27°C) for Pool and 102°F (39°C) for Spa).

BLU - 24VAC

ORN/BLK - To Spa (COMM)

BLK/ORN - To Pool (COMM)

Figure 55. 3-Wire Remote Harness Installation on the P8

Connector of the Board

4. On the “Remote Interface Harness” connect the BLUE wire to one side of the “REMOTE” switch and connect the ORANGE/BLACK wire for “SPA” operation and the BLACK/ORANGE wire for the “POOL” operation. See Figure 53.

5. Install the “Remote Interface Harness” to the P8 connector and turn power ON to the heater. See Figure 55.

For activation of the remote control, see section on page

30.

Time Clock/Fireman’s Switch

To operate the heater with a time clock, connect the timer to the reman’s switch connection in the heater’s wiring. The time clock should be of the dual switch type and set to shut o󰀨 the call for heat to the pool heater (chau󰀨e-piscine) 15 to 20 minutes prior to shutting down the pool pump.

For millivolt heaters, the reman's switch connection is a wire nut located in the Violet/Black wiring between the manual toggle switch and the gas valve. heaters, splice into the red/white wire to connect the time clock.

For digital heaters, the reman’s switch connection is located on the 14-pin header connected to the digital control board. Splice into the red wire jumper tagged – Where necessary add “Fireman’s” switch circuit here – to connect the time clock.

The reman’s switch connection on both millivolt and

digital heaters must be a dry contact and must not

supply power to the heater. Powering the reman’s

switch connection externally may damage the heater, and is not covered by warranty.

Millivolt heaters: Do not exceed 15 ft (4.5 m) of total wiring using 14 AWG stranded copper wire rated for 105°C minimum.

Digital heaters: Do not exceed 50 ft (15 m) of total wiring using 18 AWG stranded copper wire rated for 105°C minimum.

NOTE: When using a time clock, the digital heater will

display “Clock/Fireman Sw” when the reman’s switch is open, indicating that the time clock has shut o󰀨 the

call for heat.

8. While the heater is running, check the adjustment by turning the pump off and on several times. The burners should shut off immediately when the pump is turned off. If it does not, repeat the above steps until proper operation is observed.

F10671

Figure 56. Water Pressure Switch Assembly

NOTE: The sheet metal access panel should be in place at all times to protect the water pressure switch from rain and other environmental factors.

MAY REQUIRE ADJUSTMENT

FOR LOWER PRESSURE

Water Pressure Switch

The water ow switch ensures that the heater operates only when the lter pump is in operation. It is located on the In/Out header. It is factory-set at 1.75 PSI for deck-level installations.

Water Pressure Switch Adjustment

When the heater is located below the level of the spa or pool, it may be necessary to adjust the presssure switch to compensate for the no-ow static head. If it is necessary to adjust the water pressure switch, utilize the following procedure:

1. Make sure the pool filter is clean before adjusting the switch.

2. Set the heater control to the OFF mode.

3. Turn the filter pump ON and confirm that the pressure switch is closed (use a multimeter to check). If the pressure switch fails to close, either the switch setting is too high or not enough pressure is being supplied by the filter pump.

4. Turn the heater ON.

5. Manually turn the pressure adjustment knob clockwise until the heater shuts off. (A flat screwdriver may be necessary if knob is too tight.)

6. Slowly turn the adjustment knob counter-clockwise until the heater calls for heat again.

7. Turn an additional 1/2 turn counter-clockwise.

MAY REQUIRE ADJUSTMENT FOR HIGHER PRESSURE

5 ft. (1.52 m) MAX

POOL OR SPA

Figure 57. Pressure Switch Adjustment Requirements

NOTE: If heater is installed outside of the limits shown, a higher pressure rated (11 psi / 76 kPa) switch may be

used. A ow switch, mounted and wired adjacent to the

heater, may be used in place of the factory-mounted pressure switch. See "ILLUSTRATED PARTS LIST" on page 45 for 11 psi / 76 kPa water pressure switch.

Two Speed Pumps

In some cases, the ow on the low-speed is insu󰀩cient to operate the heater. This is apparent when the water pressure switch cannot be further adjusted or if the heater makes banging noises or shuts o󰀨 on high limit. In these cases, the pump must be run at high speed when heating the water.

CAUTION: Do not operate the heater without the

F10669-1

GAS VALVE

function of a properly adjusted water pressure switch

or ow switch.

Flame Roll-Out Safety Switch

Heaters are equipped with a thermal cuto󰀨 device to prevent ame roll-out in the event the heat exchanger becomes blocked. This is a “single-use” type fusible link or thermal fuse, that must be replaced when disabled by an over-temperature condition, caused by excessive restriction in the heat exchanger ue passage.

F10668

Figure 58. Flame Roll-Out Safety Switch

High Limits

The heater is equipped with two high limits.

On polymer headers both are automatic and are located in the inlet/outlet header. Both are set at 135°F (57°C).

On ASME brass header both are located on the inlet/outlet header. HL1 is manual reset and set to open at 160°F (71°C). HL2 is automatic and set to open at 135°F (57°C).

NOTE: An erratic high limit is often characteristic of an internal heat exchanger problem, e.g. scale build-up, defective bypass. Refer to "TROUBLESHOOTING" on page 40.

AUTO RESET

MANUAL RESET (ASME ONLY)

Pilot Safety - Millivolt Models

Heaters equipped with the standing pilot (millivolt system) employs a pilot which act as a safety device to shut down the ow of gas to the main burners and the pilot burner in case the pilot ame is extinguished. The pilot burner must be manually re-lighted to place the heater in operation again. Refer to the lighting instructions provided on the heater label.

Pilot Safety - Digital Models

The heater employs a pilot safety which closes the main gas valve within 8/10ths of a second whenever the pilot ame is interrupted. The pilot ame is automatically lit when the device is powered. The heater performs its own safety check and opens the main valve only after the pilot is proven to be lit.

Burner Tray Removal

1. Shut off main electrical power switch to heater.

2. Shut off gas upstream of heater.

3. Remove front door.

4. Disconnect gas line from gas valve.

5. Remove (2) screws that mount burner tray to unit, and (2) screws that secure gas valve to jacket.

6. Disconnect wires that terminate at gas valve.

7. Disconnect hi-tension wire from PC board.

8. Carefully slide out burner tray assembly.

9. Reverse above procedure to reinstall.

BURNER

HOLD-DOWN

BRACKET

PILOT

GAS

ORIFICE

Figure 59. High Limit Switches

High Limit Removal

1. Shut off main electrical power switch to heater.

2. Remove inlet/outlet sheet metal access panel.

3. Remove defective high limit and replace with the correct new high limit.

4. Replace access panel.

Figure 60. Burner Tray Assembly

Gas Valve Removal

1. Shut off gas supply to the heater. Remove gas piping to gas valve inlet.

2. Disconnect wires, pilot tubing and bleed line, if required.

3. Remove burner tray from heater.

4. Turn vertical gas pipe from manifold slightly and unscrew gas valve.

5. Reverse above procedure to reinstall.

Main Burner And Orice Removal

1. Remove burner tray, following above procedure.

2. Remove screws and burner hold-down bracket.

NOTE: If the heat exchanger is sooted badly, the burner hold-down bracket and spacer can become distorted

from direct-ame impingement and this usually

necessitates replacement of these parts.

3. Lift burners from slotted spacers and slide from orifices. Clean with a wire brush.

4. Orifices usually do not need to be replaced. To clean, run either copper wire or wood toothpick through orifice. Do not enlarge hole. To remove orifice, use a socket wrench and remove from manifold. DO NOT overtighten when reinstalling.

Pilot Removal And Cleaning

1. Disconnect pilot tubing and wires from gas valve.

2. Remove pilot assembly from burner tray.

3. Remove pilot from bracket.

4. Remove pilot orice and air opening, and clean with wire or small brush.

CAUTION! Do not enlarge hole in pilot orice.

5. Reverse above procedure to reinstall.

PILOT

AIR OPENING

ORIFICE

Heat Exchanger Removal

1. Shut water, gas and electricity off, close valves and relieve pressure, then remove relief valve. Remove side access panels.

2. Remove top jacket holding screws.

3. Remove rear top panel.

4. Remove screws mounting the rain shield to the rear panel. Also remove the screws that mount the rain shield to the sway brace. Remove rain shield.

5. Remove the four (4) screws holding down the flue collector. Remove the flue collector.

6. If ProTek Shield Assy is attached to the heater; disconnect flange nuts on Inlet/Outlet header, remove ProTek Shield Assy bonding wire from heat exchanger stud, loosen union at gas pipe and slide heater away from piping.

7. Lift heat exchanger straight up using caution not to damage refractory.

8. Reverse above procedure to reinstall. Make sure the insulation strips are properly replaced on top of the refractory retainer.

Tube Cleaning Procedure

Establish a regular inspection schedule, the frequency depending on the local water conditions and the severity of service. Do not let the tubes clog up solidly. Clean out deposits over 1/16" (1.6 mm) in thickness.

The heater may be cleaned from the return header side, without breaking pipe connections. It is preferable, however, to remove both headers for better visibility through the tubes and to be sure the ground-up lime dust does not get into the system. Note that you do not remove the top panel or the heater exchanger, generally.

After reaming, mount the wire brush in place of the auger and clean out debris remaining in the tubes.

Another method is to remove the heat exchanger, ream tubes and immerse heat exchanger in non-inhibited descale solvent for severe scale build-up.

Figure 61. Millivolt Pilot

Figure 62. Digital Pilot

Extension

Pieces (2)

Figure 63. Tube Cleaning Kit

Auger

with Carbide Tip

Wire Brush

Desooting Procedure

WARNING: Soot Is Combustible. Exercise Extreme

Care.

Soot will clog areas between ns and cause eventual tube failure. Any sign of soot at the base of the burners or around the outer jacket indicates a need for cleaning.

1. Remove top and flue collector from cabinet.

F10723

F10642-2

2. Remove “V” baffles from heat exchanger.

3. Remove burner tray. See page 33.

4. If ProTek Shield Assy is attached to the heater, remove ProTek Shield Assy bonding wire from heat exchanger stud.

5. Remove heat exchanger from the heater and wash with a garden hose, making sure soot is removed from spaces between fins.

6. Reverse above procedure to reinstall.

NOTE: In extreme cases it may be necessary to do steam cleaning at the local car wash. DO NOT WIRE BRUSH.

Combustion Chamber Removal

To remove combustion chamber, you must rst have removed the heat exchanger.

F10670

Figure 65. Well AssemblyUnitherm Governor (U.G.)

Replacement

Unitherm Governor (U.G.) Replacement

1. Shut water, gas and electricity off, close valves and relieve pressure.

2. Drain heat exchanger.

3. Remove retainer plug located next to the outlet pipe connection on polymer header models.

4. Unsnap old U.G. to remove from retainer plug. Snap in new U.G.

5. Reinstall retainer plug, taking care to lubricate gasket with a non-petroleum based grease such as AquaLube.

UG PLUG

Figure 64. Refractory Panels

WARNING: When removing the burners or heat

exchangers, take precautions to avoid creating airborne

dust and avoid inhaling airborne bers. When cleaning spills, use wet sweeping or High E󰀩ciency Particulate Air (HEPA) ltered vacuum to minimize airborne dust.

Use feasible engineering controls such as local exhaust ventilation or dust collecting systems to minimize airborne dust. Wear appropriate personal protective equipment including gloves, safety glasses with side

shields, and appropriate NIOSH certied respiratory

protection, to avoid inhalation of airborne dust and

airborne ber particles.

Immersion Well Replacement (Millivolt)

1. Shut off water to heater and drain heat exchanger.

2. Remove access panel on water connection side.

3. Remove old immersion well with bushing and sleeve.

4. Install replacement well in header.

UNITHERM GOVERNOR

GASKET

F10725

Figure 66. Unitherm Governor - Polymer

To test the operation of the Unitherm Governor - Polymer, place in hot water (over 110°F [43°C]) and watch for movement against spring. If there is no movement, replace unit.

UG/BYPASS ASSY

UNITHERM GOVERNOR

NOTE: Installation in polymer header should be hand

tight plus 1/2 turn.

Figure 67. Unitherm Governor/Bypass Valve Assy – ASME

NOTE: The U.G. on brass header models (ASME) can only be replaced by replacing the entire Unitherm Governor/Bypass Valve Assembly.

9. OPERATING INSTRUCTIONS

Before Start-Up

Burners

Keep heater area clear and free from combustibles, ammable liquids and chemicals. Do not obstruct the ow of combustion and ventilation air.

Water

Water must be owing through the heater during operation. Ensure that the system is lled with water and that the pump is operating.

Start-Up Procedures

Your pool/spa heater has been designed for years of safe and reliable pool/spa water heating. It is available with millivolt or electronic ignition. ASME-certied units typically used in commercial applications, are also available. This manual provides installation, operation, maintenance, and service information for these heaters.

TEMP ADJUST BUTTONS

MODE BUTTON

Visual inspection

With the heater on, remove the door and make a visual check of the pilot and burner. The ame should be blue with a well-dened pattern.

A yellow or “oating” ame indicates restricted air openings or incorrect orice size. Should this occur, shut the heater o󰀨 and contact your installer or gas supplier.

4" MAX

(102 mm)

Figure 69. Main Burner Flame

Figure 70. Millivolt Pilot Burner Flame

TEMP

LCD DISPLAY

Figure 68. Heater Control Toggle Switch

MODE

ON OFF

If your heater has been installed correctly, operating the heater is an easy task. The upper front panel of the heater contains the control center that allows you to turn the heater On or O󰀨 and adjust the temperature settings for the pool or spa. The temperature range is factory set from 65°F (18°C) to 104°F (40°C). See Figure 68 for location of toggle switch to turn the heater On and O󰀨.

See Section 8 for additional details about the use of the controls in the Control Adjustments subsection.

After Start-Up

Feel the inlet and outlet pipes. Outlet pipe should be only slightly warmer than the inlet. It should not be hot.

WARNING: Should overheating occur or the gas

supply fail to shut o󰀨, turn o󰀨 the manual gas control to

the appliance.

Water Pressure Switch

A water pressure switch is provided in the heater to shut o󰀨 the burners in the event that water supply is interrupted. It is very important to verify that the switch electrically opens and shuts o󰀨 the gas valve when water ow to the heater is interrupted. Otherwise rapid and severe damage will likely occur to the heater.

The water pressure switch should be checked and adjusted for proper operation by a qualied service person at the time of installation and periodically checked thereafter. Refer to "Water Pressure Switch Adjustment" on page 32 of this manual.

F10671

Figure 71. Water Pressure Switch

WARNING: Operation of the heater without water

circulation will cause rapid and severe damage to the heater, and will void the warranty.

OPERATING INSTRUCTIONS AND SHUT-OFF PROCEDURES

MILLIVOLT SYSTEM

(MANUALLY-LIGHTED PILOT)

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lit

by hand. When lighting the pilot, follow these instructions exactly.

B. BEFORE LIGHTING, smell all around the ap-

pliance area for gas. Be sure to smell near the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS: *Do not try to light any appliance. *Do not touch any electric switch; do not use any

phone in your building.

*Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instructions.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Set the thermostat to the lowest setting.

3. Turn On/O󰀨 switch to the "OFF" position.

4. Remove heater door panel.

5. Push in gas control knob slightly and turn clockwise to "OFF".

*If you cannot reach your gas supplier, call the

re department.

C. Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it. Call a qualied service technician. Force or attempted repair may result in a re or explosion.

D. Do not use this appliance if any part has been

under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force.

6. Wait 5 minutes to clear out any gas. If you then smell

gas, STOP! Follow "B" in the safety information above. If you don’t smell gas, go to the next step.

7. Locate pilot mounted in the right side panel of the

burner tray.

HONEYWELL MILLIVOLT GAS VALVE

ROBERTSHAW MILLIVOLT GAS VALVE

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat at the lowest setting.

2. Turn On/O󰀨 switch to the "OFF" setting.

3. Remove heater door panel.

8. Turn gas control knob counter-clockwise to "PILOT".

9. Place ame to end of pilot tube. Push in control knob all the way and hold to light pilot. Continue to hold control knob in for about one minute after the pilot has lighted, release knob and it will pop up. Pilot should remain lighted. If it goes out, repeat steps 5 through 9. If knob does not pop up when released, stop and immediately call your service technician or gas supplier.

10. Stand to the side of the heater and turn the gas control knob counter-clockwise

to "ON".

11. Replace heater door panel.

12. Turn On/OFF switch to the "ON " position.

13. Set thermostat to the desired setting.

4. Push the gas control knob slightly and turn clockwise

to “OFF”. Do not force

5. Replace heater door panel.

OPERATING INSTRUCTIONS AND SHUT-OFF PROCEDURES

ELECTRONIC IGNITION DIGITAL MODELS

(AUTOMATICALLY-LIGHTED PILOT)

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance is equipped with an ignition de-

vice which automatically lights the pilot. Do not try to light the pilot by hand.

B. BEFORE OPERATING, smell all around the ap-

pliance area for gas. Be sure to smell near the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS: *Do not try to light any appliance. *Do not touch any electric switch; do not use any

phone in your building.

*Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instructions.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Set the thermostat to the lowest setting.

3. Turn o󰀨 all electrical power to the appliance.

4. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

5. Remove heater door panel.

6. For Honeywell valve: Turn gas

control knob clockwise

to “OFF”. For Robertshaw valve: Models 266-406: Turn gas control knob clockwise to “OFF”. Model 206 Push in and move gas control lever counterclockwise to “OFF” position.

7. Wait 5 minutes to clear out any gas. If you then smell gas, STOP! Follow "B" in the safety information above. If you don’t smell gas, go to the next step.

8. Turn gas control knob counter-clockwise to “ON”. (Honeywell VR8340 and Robertshaw 7000)

9. Replace heater door panel.

10. Turn on all electrical power to the appliance.

11. Set thermostat to desired setting.

*If you cannot reach your gas supplier, call the

re department.

C. Use only your hand to push in or turn the gas

D. Do not use this appliance if any part has been

under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

12. If the appliance will not operate, follow the instructions “To Turn O󰀨 Gas To Appliance” and call your service technician or gas supplier.

HONEYWELL VR8340 GAS VALVE IID

GAS

INLET

ROBERTSHAW 7000 GAS VALVE IID

ROBERTSHAW 7200 GAS CONTROL LEVER SHOWN IN "OFF" POSITION

GAS

INLET

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat at the lowest setting.

2. Turn o󰀨 all the electrical power to the appliance if service is to be performed.

3. Remove heater door panel.

4. For Honeywell VR8340 and Robertshaw 7000 gas valve.

Turn gas control knob clockwise to “OFF”. Make sure knob rests against stop.

5. Replace heater door panel.

10. MAINTENANCE AND CARE

WARNING: Check the heater for possible rodent

nests after long periods of non-use.

To be followed one month after start-up and then semiannually.

1. Inspect top of heater and drafthood for soot, a sticky black substance around finned tubes and “V” baffles, and open flue gas passageways. Any visible soot should be cleaned for proper operation.

CAUTION: Soot may be combustible. Wet sooted

surfaces completely prior to cleaning. Do not use steel wire brush.

2. Clean main burners and pilot burner of dust and lint.

3. Inspect and operate all controls, gas valve and pressure relief valve (if equipped).

4. Make visual check of the burner and pilot flames. Yellow flame means restriction of the air openings. Lifting or blowing flame indicates high gas pressure. Low flame means low gas pressure. Should the latter occur, shut the heater off and contact your gas supplier or qualified service agency. See Figure 69 and Figure 70.

5. On indoor heaters, clean room intake openings to ensure adequate flow of combustion and ventilation air.

CAUTION: Combustion air must not be contaminated

by corrosive chemical fumes which can damage the heater and void the warranty.

6. Keep area around heater clear and free from combustible materials, gasoline and other flammable and corrosive vapors and liquids.

If Heater Will Not Fire:

If you have no electrical power, it may be that your “circuit breaker” has tripped. Try re-setting it.

If you have electrical power but the heater will not re check the following or see "TROUBLESHOOTING" on

page 40.

1. The time clock must be in the “ON” position.

2. Your pump strainer basket may be full. If so remove debris.

3. Your filter may be dirty. If so, backwash or clean filter. (To tell if your filter is dirty, look to see if the filter pressure is higher than usual).

4. The pump may have lost its prime and be running dry. Check the pressure on the filter. If there is no pressure, then you are not moving water (or your gauge is broken). Try to get the pump to run at its normal flow rate.

Cold Weather Operation

Important Freeze Information

MODERATE CLIMATE: Heater operation can continue during short-term cold spells. When temperatures are between 0°F (-18°C) and 32°F (0°C), ow (continuous pump operation) must be maintained.

CAUTION: Do not use the heater to maintain

water temperatures just above freezing or for freeze protection. When heater is used during freezing weather, care must be taken to avoid freeze-ups. Continuous pump operation is a must. Additional protection may be required. The heater is not warranted against freeze-ups.

COLD CLIMATE: Prolonged operation with water temperatures below 50°F (10°C) is not recommended. When starting the heater with water temperatures below 50°F (10°C), operate the heater continuously until higher temperatures are reached. Operating the heater for prolonged periods with pool water below 50°F (10°C) can seriously damage the heater, and is not covered by the warranty. For cold climate areas, please follow the winterizing procedures listed below.

Winterizing the Pool and Spa Heater

Heaters installed outdoors in freezing climate areas may be shut down for the winter. Observe the following procedure for winterizing the heater:

1. Turn off gas valve, manual gas valve, and electrical supply to the heater.

2. Remove the ProTek Shield™ Assembly (if attached). Remove the heat exchanger inspection panel on the side opposite water piping to gain access to the drain plug on the return header. Open drain plug on return header. See Figure 72 and Figure 73.

DRAIN PLUG

Figure 72. Return Header Drain Plug - Residential

("P" Prex Model)

DRAIN PLUG

Figure 73. Return Header Drain Valve - Commercial

("B" Prex Model)

O RING

F10672

F10673

11. TROUBLESHOOTING

IMPORTANT NOTICE: These instructions are intended for the use of qualied personnel who are specically trained

and experienced in the installation of this type of heating equipment and related system components. Installation and

service personnel may be required by some states to be licensed. Persons not qualied shall not attempt to install this

equipment nor attempt repairs according to these instructions.

Problem Possible Cause Corrective Action

Harmonics, or whining noise U.G. inoperative ...................................... Check movement by putting in hot water (110°F [43°C] or

*Debris or restriction in system ............... Locate the restriction and remove. Flush system and clean

*Debris in gas line................................... Remove debris or blow out gas line

Low ow.................................................. Scale forming in heat exchanger - clean heat exchanger and

Heater going on and o󰀨

continuously

Liming or scale forming in exchanger

Sooting High ow rates ........................................ Reduce by adding manual bypass valve

Pilot outage or “Weak Flame” signal

Yellow lazy ame Low gas pressure ................................... Adjust gas pressure

Outer jacket very hot (paint blistered)

Takes too long to heat pool or spa

Leaking at well Overacid ................................................. Replace well and maintain proper water chemistry

Leaking at heat exchanger Overacid ................................................. Replace heat exchanger and maintain proper water chemistry

Gasket brittle and leaking (overheated)

* Indicates symptom which usually occurs on initial start-up.

Dirty lter ................................................ Clean or replace lter

Low water level in pool ........................... Raise water level

External bypass setting out of

adjustment .............................................. Adjust bypass

*Pressure switch out of adjustment ........ Adjust pressure switch

Pool water............................................... See Water Chemistry on page 5

Bypassing too much water ..................... Inspect bypass for movement, if no movement, replace

U.G. not functioning ................................ Replace if no movement when heated

U.G. inoperative...................................... Check movement by putting in hot water (110°F [43°C] or

*Air starvation ......................................... Refer to installation instructions

*Improper venting ................................... Follow recommended installation instructions

*Insects or debris clogging burner intake

ports........................................................ Clean burners

Low gas pressure ................................... Adjust gas pressure

Restricted/dirty pilot ................................ Clean pilot

Weak pilot generator .............................. Replace pilot

*Insects or debris clogging burner intake

ports........................................................ Clean burners

*Broken refractory caused by shipping

damage or improper combustion ............ Replace refractory panels

Excessive sooting of heat exchanger ..... Determine cause of sooting and correct

Under-sized heater ................................. Calculate heating capacity of heater

Filter not running long enough ................ Reset time clock

Dirty lter ................................................ Clean lter

Gas line or meter undersized ................. Refer to installation instructions

Heater running after pump shuts o󰀨 ....... See Pressure switch adjustment

Refractory damage ................................. Replace refractory

Sooted heater ......................................... Determine cause of sooting and correct

higher)

check pool pH and total alkalinity

Adjust manual bypass valve until heater outlet water temp is between 105°F and 110°F (40°C and 43°C)

higher). If no movement, replace

Htr. output (BTUH) Pool gallonage x 8.33 or refer to heater sizing chart This does not take into account heat loss due to weather

Millivolt - Flow Chart

Light pilot

If pilot burner remains lit

Jump across both "TH"

wires on gas valves

If main burner fires,

remove jumper

Jump across pressure

If main burner fires,

remove jumper

Clean filter

Check for adequate water

flow from filter

Replace pressure switch

If main burner does not

switch terminals

fire, remove jumper

If main burner does not

fire, remove jumper

Jump across thermostat

If main burner fires,

remove jumper

Replace thermostat

If pilot burner goes out

when main burner lights

or when gas valve knob

Replace

gas

valve

If pilot burner stays on

Problem is a wire or

component short to

If main burner does

NOT fire...

Jump across each

high limit and remove

jumper

Replace high limit that

caused heater to fire

Remove both "TH"

wires from gas valve.

cabinet or low gas

pressure

is released

Relight pilot

If pilot burner

does not light

Check gas supply, gas

line size, gas pressure.

Also check for insects

or debris in pilot output

If burner does not remain

lit, attach millivolt meter

and read pilot output

If above 500mV,

replace gas valve

If below 500mV, check

gas pressure. Also check

for insects or debris in

the pilot burner

If output is still low,

replace pilot generator

Raw Output (700mV± 100)

Pilot generator disconnected from valve (knob must be held down to keep pilot on). White – Negative Red + Positive

Pilot Load (500mV± 100)

Pilot generator connected to valve-Power applied to pilot solenoid. TP(Thermopile-Robertshaw) PP(Power Pile-Honeywell) TH TP – Common TH PP – Common

Main Valve Load (200mV± 100)

Control/Limit circuit closed (All switches “ON”) TP(Thermopile-Robertshaw) PP(Power Pile-Honeywell) TH TP – Common TH PP – Common

Digital - Flow Chart

START

TURN GAS SUPPLY OFF.

TURN THERMOSTAT

(CONTROLLER) TO CALL

FOR HEAT

POWER TO PC BOARD?

(24 V NOMINAL)

YES

SPARK ACROSS

IGNITER/SENSOR GAP?

YES

WARNING: HIGH VOLTAGE

For qualied technicians ONLY

NOTE: Some heaters may be equipped with an ignition

module that shuts o󰀨 pilot gas if pilot fails to light. To reset, interrupt power to heater.

NOTE: Before troubleshooting, familiarize yourself with the start-up and check-out procedure.

Check line voltage power, low voltage transformer, limit controller, thermostat

(controller) and wiring. Make sure that the line voltage is NOT 208 VAC.

Pull ignition lead and check spark at PC board. Spark Okay?

YES NO

• Check ignition cable, ground wiring, ceramic insulator and gap, and correct.

• Check boot of the ignition cable for signs of melting or buckling. Take protective action to shield cable and boot from excessive temperatures.

Replace the PC board.

TURN GAS SUPPLY ON

PILOT BURNER LIGHTS?

YES

MAIN BURNER LIGHTS?

YES

SYSTEM RUNS UNTIL

CALL FOR HEAT ENDS?

YES

CALL FOR HEAT ENDS

SYSTEM SHUTS OFF?

YES

• Check that all manual gas valves are open, supply tubing and pressures are good, and pilot burner orice is not blocked.

• Check electrical connections between PC board and pilot operator on gas control.

• Check for 24 VAC across PV-MV/PV terminals on PC board. If voltage is okay, replace gas control; if not, replace PC board. NOTE: If PC board goes into lockout, reset system. Lockout is used on L.P.G. models.

• Check for 24 VAC across MV-MV/PV terminals. If no voltage, replace module.

• Check electrical connections between PC board and gas control. If okay, replace gas valve or gas control operator, i.e. pilot gas valve, ow switch etc.

NOTE: IF PC board goes into lockout, reset system.

• Check continuity of ignition cable and ground wire.

NOTE: If ground is poor or erratic, shutdowns may occur occasionally even though operation is normal at the time of checkout.

• Check that pilot ame covers ame rod and is steady and blue.

• If checks are okay, replace PC board.

• Check for proper thermostat (controller) operation.

• Remove MV lead at module; if valve closes, recheck temperature controller and wiring; if not, replace gas valve.

TROUBLESHOOTING

ENDS

Control Logic - Flow Chart - Digital

Power On

Is the water

temperature displayed?

YES

• Check On/Off switch (under lid on control panel)

• Check for 120/240 volts to the transformer (time clock, circuit breaker, wire connections)

• Check for 24 volts to Circuit Board (P6 connector)

Push MODE

switch to select

"Pool" or "Spa"

Push Temp

arrow to scroll to

desired temperature

Water temperature

and set

temperature

displayed?

YES

“Heating” will display briefly

“Spark”

Flame icon displayed

and flashing?

Water temp displayed?

(pilot lit and rectified)

YES

“Remote” and Water Temperature displayed

(a remote control is controlling the heater)

Note: Disconnect the remote by turning the

remote function off. See page 30 for instructions.

Is a fault code displayed and flashing?

YES

Diagnostic Readouts

“Sensor Failure,” “Sensor Open” or “Sensor Short” -

Temperature sensor out of range (replace sensor)

Sensor Failure

Inspect thermister, wires, and connector at Terminal P1 Check resistance value of the thermister. Reference to chart below. Replace thermister if not within 10% of values shown below. If okay, replace Circuit Board.

Temp Degrees F 40 50 60 70 80 90 100 106 Temp Degrees C 4 10 15 21 27 32 38 41 Resistance (k)

If okay, replace Circuit Board

“Water Sw Open” Pressure switch. Verify water flow and pressure CLEAN FILTER / STRAINER - backwash if neccessary.

“Hi Limit 1 Fault” High limit switch. Verify water flow. Inspect internal “Hi Limit 2 Fault” Thermostat (Unitherm Governor) and bypass valve. Press manual button on HL1 fault on brass (ASME) models.

“Rollout Sw Open” Rollout Sensor - Check for blocked heat exchanger and soot. Press manual reset button.

“Clock/Fireman Sw” Fireman or Remote switch connected to safety loop is in the OFF mode.

“Vent/Field Sw #1” Vent switch open. Check connections to the board. If extractor installed, troubleshoot extractor.

“Ignition Lockout” Ignition lockout. Check power at pilot valve. Check spark (bad

ignition circuit or hi-tension wire). Verify clean pilot orifice and clearance from igniter to ground rod.

“Ignition Failure” Ignition failure. Verify gas to the heater. Verify valve operation (gas present at tube fitting).

Sensor resistance at various temperatures

261.1 199.0 153.1 118.8 93.0 73.3 58.3 51.0

Heater Fired?

YES

END

Verify power at MV on P-4 Terminal on digital circuit board.

Verify power to valve MV voltage. (Replace valve.)

12. REPLACEMENT PARTS

NOTE: To supply you with the correct part, it is important that you supply the heater model number, serial number and type of gas when applicable.

Any part returned for replacement under standard company warranties must be properly tagged with a return parts tag, completely lled in with the heater serial number, model number, etc., and shipped to the Company freight prepaid.

If determined defective by the Company and within warranty, a like part or equal substitution will be returned, freight collect. Credit will not be issued.

MANUFACTURER:

2151 Eastman Avenue

Oxnard, Ca 93030

13. ILLUSTRATED PARTS LIST

I2-S

3-V

I-S

14-M

I3-S

8-S

8-C

10-M

2-M

3-S

9-M

4-M

13-M

3-M

1-V

5-C

12-M

7-C

1-G

11-S

4-C

2-J

11-M

4-V

17-HM

2-B

2-V

15-HP

3-HP

14-M

4-S

25-M

18-M

5-M

6-HP

7-HP

3-R

6-S

4-HP

2-S

5-HP

7-HP

2-HP

2-R

1-R

6-HP

20-HP

7-S

4-S

14-S

10-S

1-B

5-B

5-S

16-M

1-J

3-B

4-B

5-HM

2-S

6-HM

6-C

8-HP

2-HM

21-M

26-HM

27-HM

8-HP

6-C

1-C

9-C

7-HM

3-HM

17-HM

1-M

3-C

3-HM

7-HM

1-M

4-HM

4-S

17-HP

20-HP

FOR UNITS WITH ASME BRASS HEADERS FROM 12/2019

(PROTEK SHIELD NOT AVAILABLE ON ASME HEATERS UNTIL MARCH 2020)

6-C

14-HM

13-HM

9-S

2-HM

4-S

5-HM

2-S

6-HM

4-HM

18-HP

16-HM

15-HM

18-HM

12-HM

28-HM

9-HM

6-M

8-HM

6-M

(OPTIONAL)

2-C

10-HM

11-HM

FOR UNITS WITH ASME CAST IRON HEADERS PRIOR TO 12/2019

6-M

(OPTIONAL)

1-M

8-HP

6-C

11-HP

19-HP

6-M

(OPTIONAL)

6-C

19-HP

1-M

11-HP

1-C

18-HP

10-HP

12-HP

2-HP

13-HP

17-HP

20-HP

FOR UNITS WITH POLYMER HEADERS FROM 10/2019

8-P

14-HP

1-P

6-P

3-P

16-HP

5-P

8-HP

18-HP

FOR UNITS WITH POLYMER HEADERS PRIOR TO 10/2019

15-HP

14-HP

17-HP

12-HP

2-HP

13-HP

16-HP

10-HP

2-P

7-P

9-P

23-M

9-P

HONEYWELL MILLIVOLT PILOT

19-M

20-M

22-M

21-M

24-M

22-M

HONEYWELL IID ATMOSPHERIC PILOT

TEXAS CODE OPTION PRIOR TO 12/2019

CALL OUT DESCRIPTION 206A 266/266A 336A 399/406A

B BURNER TRAY

1-B Burner Tray w/Burners (sea level)* 010391F 010392F 010393F 010394F

2-B Burner Spacer/Hold Down Kit 010415F 010416F 010417F 010418F 3-B Burner 301210/13 301210/18 301210/22 301210/27 4-B Burner Orifice

5-B Burner Tray w/o Manifold w/o burners 010421F 010422F 010423F 010424F

1-C Thermostat Auto Reset 135 Deg Surface Mount 006725F 006725F 006725F 006725F 2-C AGS 135° (Auto Gas Shut-Off) - Red Epoxy - prior to 12/2019 600892B 600892B 600892B 600892B 3-C High Limit 140° - Black Epoxy - prior to 12/2019 600893B 600893B 600893B 600893B 4-C P.C. Board/Control 013464F 013464F 013464F 013464F 7-C LCD Display

8-C Fuse 5 AMP 013733F 013733F 013733F 013733F 5-C Thermostat Control MV Units Mechanical 003346F 003346F 003346F 003346F 6-C Temperature Sensor IID Units 009577F 009577F 009577F 009577F 9-C Thermostat Auto Reset 150/160 Deg Surface Mount (ASME Only) 018304F 018304F 018304F 018304F

1-G Combination Valve - Nat. MV 003898F 003898F 003898F 003898F

1-HP Heat Exchanger Assy Copper ***

2-HP Inlet/Outlet Header Complete

3-HP Return Header (Includes 6-HP) 015095F 015095F 015095F 015095F 4-HP Tube Bundle Copper ** & *** 010059F 010060F 010061F 010062F

5-HP Baffle (Copper Heat Exchanger) 010038F 005261F 010040F 010041F

6-HP Flange Nut Kit 008259F 008259F 008259F 008259F 7-HP O Ring Gasket (2) 006713F 006713F 006713F 006713F 8-HP Sensor Adapter Digital Electronic 006714F 006714F 006714F 006714F

9-HP Bypass Kit 006715F 006715F 006715F 006715F 10-HP Bypass Valve 006716F 006716F 006716F 006716F 11-HP Bypass Dam / Shaft 006717F 006717F 006717F 006717F 12-HP Bypass Spring (All Sizes Included) 006718F 006718F 006718F 006718F 13-HP Unitherm Governor 006719F 006719F 006719F 006719F 14-HP Unitherm Governor Plug 006720F 006720F 006720F 006720F 15-HP Drain Plug 006721F 006721F 006721F 006721F 16-HP Inlet/Outlet Header Dam 17-HP 2" CPVC Connector & Nut (2) 006723F 006723F 006723F 006723F 18-HP O Ring (2) 006724F 006724F 006724F 006724F 19-HP Inlet/Outlet Header Baffle w/Header Dam 006826F 006826F 006826F 006826F 20-HP

*FOR INSTALLATION AT OVER 2,000 FEET ABOVE SEA LEVEL, DERATE 4% PER I,000 FEET ABOVE SEA LEVEL. Refer to the heater's rating plate.

**WARNING: The Hydraulic conditions or water chemistry that caused the tube bundle to fail have very likely also damaged the bypass valve and Unitherm Governor. We recommend you replace the Unitherm Governor and inspect the bypass assembly. Failure to do so could cause premature failure of this replacement part. ***WARNING: Copper and Cupronickel heat exchangers and tube bundles are not units with suffix "X" must use Cupronickel replacement parts.

Burner Tray w/o Burners (sea level)* 010395F 010396F 010397F 010398F Burner Tray w/Gas Valve Nat Millivolt 010399F 010400F 010401F 010402F Burner Tray w/Gas Valve Pro Millivolt 010403F 010404F 010405F 010406F Burner Tray w/Gas Valve Nat IID 010407F 010408F 010409F 010410F Burner Tray w/Gas Valve Pro IID 010411F 010412F 010413F 010414F

Natural Gas Burner Orifice #50* 350079F/13 350079F/18 350079F/22 350079F/27 Burner Orifice #51* 350080F/13 350080F/18 350080F/22 350080F/27 Burner Orifice #52* 350081F/13 350081F/18 350081F/22 350081F/27 Burner Orifice #53* 350347F/13 350347F/18 350347F/22 350347F/27 Propane Gas Burner Orifice #57* 350083F/13 350083F/18 350083F/22 350083F/27 Burner Orifice #58* 350087F/13 350087F/18 350087F/22 350087F/27 Burner Orifice #59* 350350F/13 350350F/18 350350F/22 350350F/27 Burner Orifice #60* 350351F/13 350351F/18 350351F/22 350351F/27 Burner Orifice #61* 350352F/13 350352F/18 350352F/22 350352F/27

C CONTROLS

Units manufactured from 5/2011 013640F 013640F 013640F 013640F

G GAS VALVE

Combination Valve - Pro. MV 003899F 003899F 003899F 003899F Combination Valve - Nat. IID 003900F 003900F 003900F 003900F Combination Valve - Pro. IID 004306F 004306F 004306F 004306F

HP HEAT EXCHANGER - POLYMER

Units manufactured from 10/2019 017994F 017995F 017996F 017997F Units manufactured prior to 10/2019 010043F 010044F 010045F 010046F Heat Exchanger Assy Cupronickel *** Units manufactured from 10/2019 017998F 017999F 018000F 018001F Units manufactured from 7/2013 thru 9/2019 014926F 014927F 014928F 014929F Units manufactured prior to 7/2013 010356F 010357F 010358F 010359F

Units manufactured from 10/2019 017959F 017959F 017959F 017959F Units manufactured prior to 10/2019 006827F 006827F 006827F 006827F Inlet/Outlet Header (Includes 6-HP) Units manufactured from 10/2019 017965F 017965F 017965F 017965F Units manufactured prior to 10/2019 014648F 014648F 014648F 014648F

Tube Bundle Cupronickel ** & *** Units manufactured from 7/2013 014930F 014931F 014932F 014933F Units manufactured prior to 7/2013 010364F 010365F 010366F 010367F

Baffle (Cupronickel Heat Exchanger) Units manufactured from 6/2013 014934F 014935F 014936F 014937F Units manufactured prior to 6/2013 010038F 005261F 010040F 010041F

Sensor Well Millivolt 006805F 006805F 006805F 006805F

N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP N/A Use 19-HP

ProTek Shield

Assembly

017960F 017960F 017960F 017960F

interchangeable. Units with suffix "C" must use copper replacement parts and

CALL OUT DESCRIPTION 206A 266A 336A 406A

HM HEAT EXCHANGER - METAL

1-HM Heat Exchanger Assy.Copper ASME

2-HM Inlet/Outlet Header ASME Complete

15-HM Inlet & Outlet Flange - prior to 12/2019 003766F 003766F 003766F 003766F 16-HM Flange Gasket 1 1/2" Connections - prior to 12/2019 062236B 062236B 062236B 062236B

3-HM Return Header ASME

4-HM Tube Bundle Copper ASME *

5-HM Baffle 010038F 005261F 010040F 010041F 6-HM Stud Bolt Kit

7-HM Header Gasket (9) 800014B 800014B 800014B 800014B

8-HM Unitherm Governor 062234B 062234B 062234B 062234B

9-HM U.G. Retainer Spring 013792F 013792F 013792F 013792F

18-HM U.G. Plug 013738F 013738F 013738F 013738F 10-HM Bypass Valve 016194F 016194F 016194F 016194F 11-HM Bypass Spring

12-HM Drain Valve 013793F 013793F 013793F 013793F

13-HM Sensor Well 003765F 003765F 003765F 003765F

14-HM Well Retaining Clip 300203 300203 300203 300203 17-HM Rear Drain Plug & Cover 005264F 005264F 005264F 005264F 19-HM Adapter CPVC 2" 005393F 005393F 005393F 005393F 26-HM Adapter - ProTek Shield (Includes 27-HM) from 3/2020 018006F 018006F 018006F 018006F 27-HM Nut - ProTek Shield Adapter - 2-Pc from 3/2020 018007F 018007F 018007F 018007F 28-HM U.G./Bypass Assembly (Units manufactured from 12/2019) 017958F 017958F 017962F 017962F

CALL OUT DESCRIPTION 206A 266/266A 336A 399/406A

1-J Transformer 120/240/24V 006736F 006736F 006736F 006736F 2-J Rocker Switch 009493F 009493F 009493F 009493F

1-M Pressure Switch 1.75 PSI 006737F 006737F 006737F 006737F

2-M Thermostat Knob 009499F 009499F 009499F 009499F

3-M Thermostat Shaft MV 800307 800307 800307 800307 4-M Knobstop 006886F 006886F 006886F 006886F 5-M Thermal Fuse 005899F 005899F 005899F 005899F 6-M PRV

7-M Deliming Kit 052871F 052871F 052871F 052871F 8-M Wire/Harness Millivolt 010386F 010386F 010386F 010386F

9-M Control Bezel MV (Includes Dial Decal) 009489F 009489F 009489F 009489F

10-M Dial Decal MV 009858F 009858F 009858F 009858F 11-M Control Bezel (Includes Switch Decal)

12-M Switch/Decal-Membrane

13-M Control Bezel Cover 009487F 009487F 009487F 009487F 14-M Gasket Insulation (Swaybrace & Jacket Top) 010350F 010350F 010350F 010350F 15-M Touch-up Paint

16-M Tie Down Bracket (Optional) 011636 011636 011636 011636 17-M Texas Code Option (ASME Only) - Units manufactured prior to 12/2019

21-M T & P Gauge 014647F 014647F 014647F 014647F

22-M 2" CPVC Connector (Outlet Plumbing)

23-M 2" CPVC Connector & Nut (2) 006723F 006723F 006723F 006723F

18-M PC Board Shield (Optional) 015557F 015557F 015557F 015557F 25-M Gas Line Finish Flange 016160F 016160F 016160F 016160F

*WARNING: The Hydraulic conditions or water chemistry that caused the tube bundle to fail have very likely also damaged the bypass valve and Unitherm Governor. We recommend you replace the Unitherm Governor and inspect the bypass assembly. Failure to do so could cause premature failure of this replacement part.

Units manufactured from 12/2019 (Brass) 017983F 017984F 017985F 017986F Units manufactured prior to 12/2019 (Cast Iron) 010051F 016193F 010053F 010054F Heat Exchanger Assy.Cupronickel ASME Units manufactured from 12/2019 (Brass) 017987F 017988F 017989F 017990F Units manufactured prior to 12/2019 (Cast Iron) 010360F 010361F 010362F 010363F

Units manufactured from 12/2019 (Brass) 017961F 017961F 017992F 017992F Units manufactured prior to 12/2019 (Cast Iron) 006730F 006730F 006730F 006730F Inlet/Outlet Header ASME (Header Only) Units manufactured from 12/2019 (Brass) 017966F 017996F 017996F 017996F Units manufactured prior to 12/2019 (Cast Iron) 012319F 012319F 012319F 012319F

Flange Gasket 2" Connections - prior to 12/2019 800080B 800080B 800080B 800080B

Units manufactured from 12/2019 (Brass) 017973F 017973F 017973F 017973F Units manufactured prior to 12/2019 (Cast Iron) 006731F 006731F 006731F 006731F

Units manufactured from 12/2019 017974F 017975F 017976F 017977F Units manufactured prior to 12/2019 010055F 006733F 010057F 010058F Tube Bundle Cupronickel ASME * Units manufactured from 12/2019 017978F 017979F 017980F 017981F Units manufactured prior to 12/2019 010368F 010369F 010370F 010371F

Units manufactured from 12/2019 017982F 017982F 017982F 017982F Units manufactured prior to 12/2019 007870F 007870F 007870F 007870F

Units with Plastic Bypass Valve (Units manufactured from 3/5/17 to 12/19) 016196F 016196F 016196F 016196F Units with Brass Bypass Valve (Units manufactured prior to 3/5/17) 013794F 013794F 013794F 013794F

J CONTROL BOX

M MISCELLANEOUS COMPONENTS

Pressure Switch 1.75 PSI Complete Kit (Units manufactured from 12/2019) Pressure Switch 11 PSI Special-See Water Pressure Switch Adj.

PRV - 75 PSI ASME (Brass) Units manufactured from 12/2019 017957F 017957F 017957F 017957F PRV - 125 PSI (Optional) Units manufactured prior to 12/2019 008091F 007224F 007224F 007224F

Wire/Harness IID 009490F 009490F 009490F 009490F

Units manufactured from 5/2011 013491F 013491F 013491F 013491F Units manufactured prior to 5/2011 009491F 009491F 009491F 009491F

Units manufactured from 5/2011 013492F 013492F 013492F 013492F Units manufactured prior to 5/2011 009492F 009492F 009492F 009492F

Green 750125 750125 750125 750125 Dark Gray 750126 750126 750126 750126 Cool Dark Gray 750256 750256 750256 750256 Warm Dark Gray 750258 750258 750258 750258

Flanged Connection (Not Shown) 015889F 015889F 015889F 015889F NPT Connection (Not Shown) 015890F 015890F 015890F 015890F

NPT Connection 013795F 013795F 013795F 013795F Flanged Connection 015883F 015883F 015883F 015883F

24-M O Ring (2) 006724F 006724F 006724F 006724F

018297F 018297F 018297F 018297F 009133F 009133F 009133F 009133F

CALL OUT DESCRIPTION 206A 266/266A 336A 399/406A

P PILOT

1-P Pilot Nat. MV 600525B 600525B 600525B 600525B

2-P 3-P Pilot Orifice Nat. MV 003901F 003901F 003901F 003901F

4-P Pilot Orifice Nat. IID .020 003903F 003903F 003903F 003903F

5-P Pilot Generator MV 600019B 600019B 600019B 600019B 6-P Pilot MTG Bracket MV 010352F 010352F 010352F 010352F 7-P Pilot Mounting Bracket IID 306692 306692 306692 306692 8-P Lighter Tube (MV Units Only) 062996 062996 062996 062996 9-P Pilot Tube 004078F 004078F 004078F 004078F 10-P Hi Tension Wire IID with Pilot Electrode N/A N/A N/A N/A 11-P Pilot Shield 010351F 010351F 010351F 010351F

1-R Refractory Common Lt & Rt 010088F 010088F 010088F 010088F 2-R Refractory Uncommon (Front & Rear) 010089F 010090F 010091F 010092F 3-R Refractory Retainer Kit 010387F 010388F 010389F 010390F

1-S Jacket Top (Louvered) 010047F 010048F 010049F 010050F 2-S Flue Collector (Units with Polymer Header) 010071F 010072F 010073F 010074F

3-S Door Assy

14-S Screw & Retainer 006744F 006744F 006744F 006744F

4-S Access Panel Set (3 Pcs Units with Polymer Header) 010311F 010311F 010311F 010311F

5-S Jacket Side Panel Right 010376F 010376F 010376F 010376F 6-S Jacket Side Panel Left 010377F 010377F 010377F 010377F 7-S Jacket Rear Panel (2 Pcs.) 010372F 010373F 010374F 010375F 8-S Poolstat Cover/Lock 009505 009505 009505 009505 9-S High Limit Cover - prior to 12/2019 010319F 010319F 010319F 010319F 10-S Base Heat Shield - prior to 10/2019 010320F 010320F 010320F 010320F 11-S Up Front Control Panel

12-S High Limit Shield 010342F 010342F 010342F 010342F 13-S Weather Shield 010325F 010326F 010327F 010328F

1-V Indoor Stack Kit (Includes inner adapter panel) 009838 009839 009840 009841

2-V Stack Adapter 010330F 010331F 010332F 010333F 4-V Outer Stack Adapter 011461F 011462F 011463F 011464F 3-V "Pagoda" Top

Atmospheric CONVERSION KITS*

Gas Conversions Nat. to Pro. MV Pilot 004690B 004690B 004692B 004692B Pro. to Nat. MV Pilot 010419F 010419F 010420F 010420F Nat. to Pro. IID Pilot ** ** ** ** Pro. to Nat. IID Pilot ** ** ** **

Pilot Pro. MV 600575B 600575B 600575B 600575B

Pilot Nat & Pro IID 002003F 002003F 002003F 002003F

Pilot Orifice Pro. MV 003902F 003902F 003902F 003902F

Pilot Orifice Pro. IID .012 004308F 004308F 004308F 004308F

R REFRACTORY

S SHEETMETAL

Flue Collector (Units with Metal Header) 010075F 010076F 010077F 010078F

Raypak Cool Dark & Warm Dark Gray 013859F 013860F 013861F 013862F Green 010378F 010379F 010380F 010381F Rheem Cool Dark & Warm Dark Gray 013863F 013864F 013865F 013866F Green 010382F 010383F 010384F 010385F Ruud Cool Dark & Warm Dark Gray (Units mfd after 9/2012) 013859F 013860F 013861F 013862F Warm Dark Gray (Units manufactured prior to 9/2012) 013867F 013868F 013869F 013870F Green 010382F 010383F 010384F 010385F Jacuzzi N/A 016698F N/A 016699F

Access Panel Set - ASME Access Panel Set (3 Pcs. for BR Header) - from 12/2019 017967F 017967F 017967F 017967F Access Panel Set (3 Pcs. for CI Header) - prior to 12/2019 010312F 010312F 010312F 010312F

Green 010321F 010322F 010323F 010324F Cool Dark Gray 013887F 013888F 013889F 013890F Warm Dark Gray 013891F 013892F 013893F 013894F

V VENTING

Outdoor Stack Kit (Includes inner adapter panel) 009834 009835 009836 009837

Cool Dark Gray 013883F 013884F 013885F 013886F Green 010334 010335 010336 010337

* Gas conversions are to be done only by a qualified agency. ** Conversion must be made with complete burner tray and gas valve (see item 1-B).

NOTES

Raypak 206A, 266, 266A, 336A, 399 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1. WARNINGS

Pay Attention to These Terms

2. WATER CHEMISTRY

Automatic Chlorinators and Chemical Feeders

3. BEFORE INSTALLATION

Receiving equipment

Elevation

Ambient Temperature Rating

4. INSTALLATION

Installation Codes

Clearances

Outdoor Heater Installation

Combustion and Ventilation Air

Vent Piping

D-2 Power Vent Kit

Gas Supply Connections

Flow Rate

PROTEK SHIELD ASSEMBLY

Internal Automatic Bypass Valve

Unitherm Governor Operation

External Auxiliary Bypass Valve

Auxiliary Bypass Valve Adjustment

Pressure Relief Valve Installation

Heat Exchanger Reversal

Plumbing Diagrams

5. ELECTRICAL WIRING

Electrical Power Draw

Transformer Wiring

6. WIRING DIAGRAM - MILLIVOLT

7. WIRING DIAGRAM - DIGITAL

8. CONTROLS

Control Panel Removal

Control Adjustments – Digital Models

Operation

Status and Diagnostics

9. OPERATING INSTRUCTIONS

Before Start-Up

Start-Up Procedures

Visual inspection

Water Pressure Switch

10. MAINTENANCE AND CARE

Cold Weather Operation

11. TROUBLESHOOTING

Millivolt - Flow Chart

Digital - Flow Chart

Control Logic - Flow Chart - Digital

12. REPLACEMENT PARTS

13. ILLUSTRATED PARTS LIST