Page 1
SMARTPILOT CONTROLLER
INSTALLATION GUIDE
Parts supplied
ST6001+ ST7001+ or ST8001+
Gasket
Site requirements
www.raymarine.com
Check
Gasket
Sun Cover
Tools required
Power Drill
SmartPilot ST6001
Controller
and / or
SeaTalk Cables
Measure
Pencil
Sun Cover
Stud
(x2 ST6001)
(x4 ST7/8001)
3
5mm (
90 mm (3½ in) Hole Cutter
SmartPilot Controller
(ST8001 shown)
Screw
(x2 ST6001)
(x4 ST7/8001)
Connector (x2)
in) Drill
/
16
Check
Min 0.8m (2ft 6in)
D6354-1
Raymarine Ltd, Portsmouth, Hampshire, UK PO3 5TD
Raymarine Inc. Nashua, NH 03063-4219, USA
Recyclable Material - Please dispose of responsibly.
+44 (0) 23 9269 3611
Toll Free: 800-539-5539
+1 603-881-5200
ST6001 controller template - ST7001 and ST8001 template on reverse
Control Unit:
Surface mount template
TOP
Machine hole
90 mm (3.55 in)
diameter
Drill 5 mm (3/16 in)
diameter hole
Remove shaded areas only
Check
87014-1
2. ST6001 Controller
Step 1
x2
Control Unit:
Surface mount template
Remove shaded areas only
Drill 5 mm (3/16 in)
diameter hole
x2
TOP
Machine hole
90 mm (3.55 in)
diameter
Drill 5 mm (3/16 in)
diameter hole
D6355-1
Drill 5 mm (3/16 in)
diameter hole
Sun cover
edge
Instrument
edge
D6360-1
Step 2
Control Unit:
Surface mount template
Remove shaded areas only
90.6 mm (3.56 inch)
Drill 5 mm (3/16 in)
diameter hole
TOP
Machine hole
90 mm (3.55 in)
diameter
Drill 5 mm (3/16 in)
diameter hole
D6356-1
Page 2
2. ST7001 and ST8001 Controller
3. ST6001
Step 1
Step 2
x2
Control Unit:
Surface mount template
Remove shaded areas only
x2
Control Unit:
Surface mount template
TOP
Machine hole
90 mm (3.55 in)
diameter
TOP
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
Instrument
edge
Sun cover
edge
Step 1 Step 2
D4235
-5
3. ST7001 and ST8001
Step 1 Step 2
4. ST6001
Machine hole
90 mm (3.55 in)
diameter
Remove shaded areas only
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
Instrument
edge
Sun cover
edge
D4235-5
D6357-1
D6358-1
ST7001 and ST8001 controller template - ST6001 template on reverse
Control Unit:
Surface mount template
4. ST7001 or ST8001
Remove shaded areas only
90 mm (3.55 in)
Machine hole
diameter
TOP
?
Refer to Autopilot Manual
Référer le manuel de pilote automatique
Siehe Autopiloten Handbuch
Refiérase al manual del piloto
Refiérase a manual de autopilot
SmartPilot
System
Commissioning
your SmartPilot
D6359-1
D4235-5
Sun cover
edge
Instrument
edge
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
D6361-1
Loading...