RANDELL CR9053 User Manual
Preparation Table Raised Condiment Rail models 8000N
model 8148N 8260N 8268N 8383N 8395N 84111N
Description:
Available in six convenient sizes, 48” one door, 60” & 68” two
door, 83” and 95” three door, and 111” four door. The 8000N
Series raised condiment rail preparation table meets the
1998 NSF/ANSI standard 7, 41˚ F. pan product temperature
requirements. Our Exclusive Dual System is proven by over
15 years of wrapped coldwall construction experience. Rail is
provided with an Exclusive drain for easy clean-up.
Specifications:
CABINET EXTERIOR: Unit top and raised rail will be formed from four piece
20 gauge stainless steel with a 1-1/2” 90˚ nosing/top turndown. The raised
refrigerated rail will be mechanically cooled and shall be provided with one
single opening to allow flexible pan configurations. The interior of the rail
will be constructed of three-piece construction with coved corners for easy
cleaning. Rail will hold 6” deep pans - not included. The pans will set on
an integral recessed pan ledge (1” at front and 3” at rear) making clean-up
easy without requiring the removable of any pan supports. On the 8383N,
8395N and 84111N, a removable mullion (below the intersection of the two
covers) allows the addition of one more 1/3 pan when removed. All units
provided with hinged removable stainless steel covers, fabricated from 20
gauge stainless steel, and supplied with a combination of covers which allow
maximum access to the pans. Unit bottom and exterior back are galvanized
metal. Exterior ends are finished in stainless steel. New hinged louver for
easier cleaning of the coil and draining the rail. Unit mounted on 6” (overall)
high swivel casters (front two with locks).
CABINET BASE INTERIOR: Interior floor, rear and top shall be anodized aluminum.
Base interior ends and door openings shall be thermoformed high impact
ABS. Each section will be provided with (1) removable interior epoxy-coated
wire shelf. The base shall be foamed in place polyurethane insulation with a
minimum thickness of 2”.
DOORS: Stainless steel front with easy to grasp recessed handles. Doors
mounted on heavy duty stainless steel concealed type hinges with pivot pin
in nylon bushing. Door interior is deep drawn thermoformed high impact ABS
with press-fit replaceable magnetic gaskets, designed for long life and easy
maintenance. Doors are foamed in place polyurethane insulation.
model 8268N
shown
ELECTRICAL: The units will be provided with a 8’ power cord and 3-wire grounded plug
as standard, pre-wired for 115 volt, 60 hertz, single phase operation. Export voltages
are available and require hard wiring in the field to the units main junction box, (unit
will be shipped on legs for export applications, unless specified otherwise).
This equipment is intended for use in rooms having an ambient temperature of 86˚F
(30˚C) or less.
Standard Features:
• Meets 1998 NSF/ANSI Standard 7,41˚ F Product Temperature Requirements
• Recessed Wrapped Coldwall Rail with Exclusive Separate
Temperature Controls & Expansion Valve for Base and Rail
• Exclusive Press Fit Magnetic Removable Gaskets
• Separate Dual Control System for Rail & Base Allows
Shutting Rail Off at Night for Up to 60% Energy Savings
• Condensing unit with Hot Gas Condensate Evaporator
• New Hinged Louver for panel for easy access to drain gate
valve, rail temperature control and cleaning of condenser coil
• Exclusive rail drain for easy clean-up
REFRIGERATION SYSTEM: The system will utilize R-404a refrigerant and be
provided with a hot gas condensate evaporation system. Dual refrigeration
system with independent controls for the base and the rail. The base will have
a blower coil with a dedicated metering device and solenoid valve allowing
the thermostatic control to independently control the base temperature. The
raised mechanically cooled rail will be controlled utilizing an expansion valve
metering device with its own solenoid valve and thermostat. An on/off switch,
located directly behind the hinged louver, is provided as standard to allow the
rail to be shut off independently of the base. A pressure control is provided to
monitor the dual systems performance.
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most
updated product information and specifications.
Options & Accessories:
Patented triple or double drawer cartridges for 27” openings
Overshelf assembly
Cutting boards
Stainless steel back
Legs in lieu of casters
Pull-out catch pan assemblies
Tray racks for 18 x 26 sheet pans for 24” or 27” openings
Export voltages available
Randell Preparation Table, Page 1
PP SPEC0006 Rev. A
Revised 07/06
27" REFRIG.
HING
HINGED LOUVER
48"
P
A
N
E
L
ED
PANEL
24" REFRIG. 24" REFRIG.
HINGED LOUVER
PANEL
60"
27" REFRIG. 27" REFRIG.
HINGED LOUVER
PANEL
68"
Models 8000N
21" REFRIG.24" REFRIG. 24" REFRIG.
HINGED LOUVER
83"
PANEL
27" REFRIG. 27" REFRIG.27" REFRIG.
Door Opening Size - Interior Depth
Door Width
Clearances Through Door
Lt to Rt
21”
27”
24”
16”
22”
19”
95"
Tp to Btm
HINGED LOUVER
PANEL
Interior Depth
Behind Door
22.25”
26”
22.25”
26”
22.25”
26”
24" REFRIG.24" REFRIG. 24" REFRIG. 21" REFRIG.
HINGED LOUVER
111"
PANEL
35"
42.9"
33"
Model
8148N
8260N
8268N
8383N
8395N
84111N
L
48”
60”
68”
83”
95”
111”
D
33”
33”
33”
33”
33”
33”
H
42.9”
42.9”
42.9”
42.9”
42.9”
42.9”
Doors
(1)27”
(2)24”
(2)27”
(2)24”,(1)21”
(3)27”
(3)24”,(1)21”
Storage Cu. Ft.
9.0
14.67
17.76
23.55
28.18
32.81
Pan Capacity
(6)1/3 or (12)1/6
(8)1/3 or (16)1/6
(9)1/3 or (18)1/6
(10)1/3 or (20)1/6
(12)1/3 or (24)1/6
(14)1/3 or (28)1/6
HP
1/3
1/3
1/3
1/2
1/2
5/8
Volt
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
115/60/1
Amps
9
9
9
12
12
12.8
NEMA
5-15P
5-15P
5-15P
5-15P
5-15P
5-20P
BTU Rating
1380
1380
1380
2385
2385
3350
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net
© 2009 Unified Brands. All Rights Reserved. DOVER® and the DOVER® Logo are registered
trademarks in the United States [and various other countries] of Unified Brands, a
wholly-owned subsidiary of Dover Corporation.
Ship Wt.
342
400
428
550
600
638
Preparation Table High Volume Saladtop models 9000K-7
model 9030K-7 9040K-7 9045K-7 9050K-7
Description:
Self-contained refrigerated salad top unit with raised rim cutouts
in stainless steel top. Recessed pan ledge to hold 6” deep pans,
pans not provided. R-134a expansion valve refrigeration system
is “CFC free”. Randell mullion blower coil with thermostatic
control, cools base and pans. Stainless steel hinged roll cover,
lift-off louver, full length cutting board, foamed in place urethane
insulation, condensate evaporator, locking casters and cordset
for 115V operation.
Specifications:
CABINET EXTERIOR: Cabinet body is constructed of all metal. Cabinet
top to be one piece die-formed 20 gauge stainless steel with 1 1/2” high
square nosing. Top to have raised rim cutouts with recessed pan ledge to
hold 6” deep pans, pans not provided. Hinged, stainless steel roll cover.
All units are standard with stainless steel ends. Door openings to be
ABS and contain magnetic strip for positive sealing of gaskets. Louver
is stainless steel, removable without tools. Full length, NSF composition
10” cutting board provided. 10” wide work surface to be at 34.875”
work height with unit on standard 6” casters (front two with locks).
CABINET INTERIOR: Unit base interior to be ABS thermoplastic at ends
only. Anodized aluminum base liner to be coved cornered to form interior
bottom, back and top meeting N.S.F. standard #7. One baked enamel
finished shelf provided behind each door. Unit insulated with a minimum
of 2.5” of CFC free, foamed in place polyurethane. Full depth interior
allows for the use of optional 18” x 26” tray racks.
DOORS: Easy to grasp recessed handles, mounted on heavy duty
concealed hinges. Hinges are all stainless steel with bronze pivot pin in
nylon bushing. Doors with foamed in place insulation, press fit magnetic
gaskets - (designed for installation & removal without tools), and deep
draw ABS interior liner for maximum insulation value.
REFRIGERATION: CFC free, R-134a Expansion Valve refrigeration system
to include condensing unit, and thermostatic control for field adjustability.
Compressor housing to allow maximum airflow and permit mounting
of standard condensate evaporator. Mullion coil, is coated to resist
corrosion, and offers maximum air flow while allowing use of the full
depth interior for maximum product storage, and the use of optional tray
racks. Units totally prewired and to be supplied with 8’ cordset (NEMA
5-15P) for 115V operation.
This equipment is intended for use in rooms having an ambient
temperature of 86˚F (30˚C) or less.
model 9045K-7
shown with optional
refrigerated drawers
Standard Features:
• Side mounted compressor with mullion “Turbo” coil provides
proper pan cooling, and “full depth” usable interior space
• “CFC free” R-134a refrigerant
• Expansion valve
• Hot gas condensate evaporator
• Exterior stainless steel top & ends
• Foamed in place “CFC free” urethane insulation
• Raised rim cutouts in stainless steel top with recessed
pan ledge to hold 6” deep pans, pans not provided
• Stainless steel, hinged roll cover
• Full length NSF approved 10” wide composition
cutting board
• Durable shelf supports molded into sides
• 6” casters, front two with locks
• 8’ cord and plug for 115 volt operation
• Self-closing doors with exclusive press-fit magnetic gaskets
Options & Accessories:
Stainless steel back panel
Tray racks for 24” or 27” openings only
Refrigerated drawers
Overshelves
Export voltages available
Legs in lieu of casters
Stainless steel mullion covers
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most
updated product information and specifications.
Randell Preparation Table, Page 2
PP SPEC0007 Rev. B
Revised 02/08
Models 9000K-7
48" X 10" X .375"
POLY CUTTING BOARD
*
18"REFRIG. 18"REFRIG.
LOUVERED
END PANEL
48"
84" X 10" X .375"
POLY CUTTING BOARD
60" X 10" X .375"
POLY CUTTING BOARD
1.875"
1.625"5.188"
*
24"REFRIG. 24"REFRIG.
LOUVERED
END PANEL
60"
14.211"
1.875"
1.5"
LOUVERED
END PANEL
15.769"
72" X 10" X .375"
POLY CUTTING BOARD
*
72"
9.25"
1.5"
27"REFRIG.27"REFRIG.
13.375"
LOUVERED
END PANEL
*
24"REFRIG.24"REFRIG. 18"REFRIG.
84"
1.625"
44.125"
34.875"
33"
Drawings are to be viewed in the same order as the chart, one drawing to represent refrigerator and freezer units
Model
9030K-7
9040K-7
9045K-7
9050K-7
L
48”
60”
72”
84”
D
33”
33”
33”
33”
H
34.875”
34.875”
34.875”
34.875”
Doors
(2)18”
(2)24”
(2)27”
(2)24”,(1)18”
Storage Cu. Ft.
10.04
14.67
19.30
23.93
Pan Capacity
(3)1/1 or (18)1/6
(4)1/1 or (24)1/6
(5)1/1 or (30)1/6
(5)1/1 or (30)1/6
HP
1/3
1/3
3/8
3/8
Volt
115/60/1
115/60/1
115/60/1
115/60/1
Amps
9
9
9
9
NEMA
5-15P
5-15P
5-15P
5-15P
Ship Wt.
335
460
475
520
1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net
© 2009 Unified Brands. All Rights Reserved. DOVER® and the DOVER® Logo are registered
trademarks in the United States [and various other countries] of Unified Brands, a
wholly-owned subsidiary of Dover Corporation.
Preparation Table Side Mount Saladtop models 9200-32-7
model 9210-32-7 9200-32-7 9230-32-7 9220-32-7
Description:
Randell mullion blower coil, with thermostatic control, cools pans
and/or base, and allows for use of full depth interiors. R-134a
expansion valve refrigeration system in refrigerators are CFC free.
Units with durable shelf supports molded into sides, lift-off louver,
condensate evaporator, “CFC free” foamed in place insulation
and 6” high adjustable legs. Cordset for 115V operation.
Specifications:
CABINET EXTERIOR: Cabinet body is constructed of all metal. The
top, front, sides and louver panel are stainless steel. Bottom &
back of unit are corrosion resistant steel. Saladtop refrigerator to
have top cutout with sanitary raised rim and recessed adaptor.
Hinged, stainless steel roll-cover. Full length, NSF composition
12” cutting board provided.
CABINET INTERIOR: Interior of cabinet is fully coved to meet
N.S.F. standard #7. The Interior bottom, back, and top are
anodized aluminum with coved corners for easy clean-up. The
interior ends are ABS. Shelf supports molded into sides. Unit
insulated with a minimum of 2.5” of CFC free, foamed in place
polyurethane.
DOORS: Stainless steel front with easy to grasp recessed handles,
mounted on heavy duty concealed hinges. Hinges are all stainless
steel with bronze pivot pin in nylon bushing. Doors with foamed
in place insulation, press fit magnetic gaskets - (designed for
installation & removal without tools), and deep draw ABS interior
liner for maximum insulation value.
REFRIGERATION: Refrigerators utilize a CFC free, R-134a
Expansion Valve refrigeration system that includes condensing
unit, and thermostatic control for operator adjustability.
Compressor housing to allow maximum airflow and permit
mounting of standard hot gas condensate evaporator. Mullion
coil, is coated to resist corrosion, and offers maximum air flow.
This equipment is intended for use in rooms having an ambient
temperature of 86˚F (30˚C) or less.
model 9200-32-7
shown
Standard Features:
• Side mounted compressor with mullion “Turbo” coil
provides proper pan cooling, and “full depth” usable
interior space
• R-134a refrigerant in refrigerators and R-404a in
freezers both are “CFC free”
• Exterior stainless steel top & front
• Foamed in place “CFC free” urethane insulation
• Self-closing doors with exclusive press-fit magnetic
gaskets
• Shelf supports molded into sides
• Expansion valve
• Condensate evaporator
• Cord and plug for 115 volt operation
• 6” high adjustable legs
• Full length NSF approved 12” wide composition cutting
board
• Stainless steel roll cover
Options & Accessories:
Stainless steel back panel
Refrigerated drawers
Tray racks for 24” or 27” openings only
Overshelves
Casters
Export voltages available
1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net
Please reference our website for the most
updated product information and specifications.
Randell Preparation Table, Page 3
PP SPEC0008 Rev. A
Revised 07/06
Loading...