RANDELL 8000W User Manual

PROJECT NAME:

LOCATION:

ITEM NO:

PREPARATION TABLE

RAISED CONDIMENT RAIL MODEL 8000W

Available in three convenient sizes, 48” one door, 68” two door and 95” three door. The 8000W Series raised
condiment rail preparation table meets the 1998 NSF/ANSI standard 7, 41˚ F. pan product temperature
requirements. Our exclusive dual system is proven by over 20 years of wrapped coldwall construction
experience. Rail is provided with an exclusive drain for easy clean-up.

AVAILABLE MODELS:

8148W
8268W
8395W

STANDARD FEATURES:

• Meets 1998 NSF/ANSI standard 7,41˚ F product

temperature requirements

•

Recessed wrapped coldwall rail with exclusive separate
temperature controls & expansion valve for base and rail

• Exclusive press fit magnetic removable gaskets

• Separate dual control system for rail & base allows

shutting rail off at night for up to 60% energy savings

• Condensing unit with hot gas condensate evaporator

• Hinged louver for panel for easy access to drain

gate valve, rail temperature control and cleaning of
condenser coil

• Exclusive rail drain for easy clean-up

CABINET EXTERIOR: Unit top and raised rail will

be formed from four piece 20 gauge stainless steel with
a 1-1/2” 90˚ nosing/top turndown. The raised refrigerated
rail will be mechanically cooled and shall be provided with
one single opening to allow flexible pan configurations.
The interior of the rail will be constructed of three-piece
construction with coved corners for easy cleaning. Rail
will hold 6” deep pans - not included. The pans will set
on an integral recessed pan ledge (2.5” at front and

4.5” at rear) making clean-up easy without requiring the

removable of any pan supports. All units provided with
hinged removable stainless steel covers, fabricated from
20 gauge stainless steel, and supplied with a combination
of covers which allow maximum access to the pans. Unit
bottom and exterior back are galvanized metal. Exterior
ends are finished in stainless steel. Standard hinged
louver for easier cleaning of the coil and draining the rail.
Unit mounted on 6” (overall) high swivel casters (front
two with locks).

interior epoxy-coated wire shelf. The base shall
be foamed in place polyurethane insulation with a
minimum thickness of 2”.

DOORS: Stainless steel front with easy to grasp

recessed handles. Doors mounted on heavy duty
stainless steel concealed type hinges with pivot
pin in nylon bushing. Door interior is deep drawn
thermoformed high impact ABS with press-fit
replaceable magnetic gaskets, designed for long life
and easy maintenance. Doors are foamed in place
polyurethane insulation.

REFRIGERATION SYSTEM: The system will

utilize R-404a refrigerant and be provided with a hot
gas condensate evaporation system. Dual refrigeration
system with independent controls for the base and the
rail. The base will have a blower coil with a dedicated
metering device and solenoid valve allowing the
thermostatic control to independently control the base
temperature. The raised mechanically cooled rail will
be controlled utilizing an expansion valve metering
device with its own solenoid valve and thermostat. An
on/off switch, located directly behind the hinged louver,
is provided as standard to allow the rail to be shut
off independently of the base. A pressure control is
provided to monitor the dual systems performance.

ELECTRICAL: The units will be provided with a

8’ power cord and 3-wire grounded plug as standard,
pre-wired for 115 volt, 60 hertz, single phase
operation. Export voltages are available and require
hard wiring in the field to the units main junction box,
(unit will be shipped on legs for export applications,
unless specified otherwise).

This equipment is intended for use in rooms having an
ambient temperature of 86˚F (30˚C) or less.

QTY:

MODEL NO:

AIA NO:

SIS NO:

CSI SECTION: 11400

8000W Raised rail preparation tables.
Model 8268W shown.

OPTIONS/ACCESSORIES:

Patented triple or double

drawer cartridges for 27”

openings
Overshelf assembly
Cutting boards
Stainless steel back
Legs in lieu of casters
Pull-out catch pan assemblies
Tray racks for 18 x 26 sheet

pans for 24” or 27” openings

CABINET BASE INTERIOR: Interior floor, rear

and top shall be anodized aluminum. Base interior ends
and door openings shall be thermoformed high impact
ABS. Each section will be provided with (1) removable

ORIGIN OF MANUFACTURE: Designed and

manufactured in the United States.

Prep Tables

PPSPEC8000W RevA

Revised 10/13

8000W

Model L W H Doors Storage Cu. Ft. Pan Capacity HP Volt Amps NEMA BTU Rating Ship Wt.

8148W 48” 33” 46” (1)27” 7.7 (9)1/3 or (18)1/6 1/3 115/60/1 9 5-15P 1380 355

8268W 68” 33” 46” (2)27” 15.8 (15)1/3 or (30)1/6 1/3 115/60/1 9 5-15P 1380 450

8395W 95” 33” 46” (3)27” 24.5 (21)1/3 or (42)1/6 1/2 115/60/1 12 5-15P 1380* 625

Door Opening Size/Interior Depth: Clearances through door = 22” left to right, 22.25” top to bottom. Interior depth behind door = 26”
*Additional coil installed if drawers or tray racks are ordered.

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2013 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.