RANDELL 8000N User Manual

PROJECT NAME:

LOCATION:

ITEM NO:

PREPARATION TABLE

RAISED CONDIMENT RAIL MODEL 8000N

The 8000N Series raised condiment rail preparation table meets the 1998 NSF/ANSI standard 7, 41˚ F. pan
product temperature requirements. Our Exclusive Dual System is proven by over 15 years of wrapped coldwall
construction experience. Rail is provided with an Exclusive drain for easy clean-up.

AVAILABLE MODELS:

8148N
8260N
8268N
8383N
8395N
84111N

STANDARD FEATURES:

• Meets 1998 NSF/ANSI standard 7,41˚ F product

temperature requirements

•

Recessed wrapped coldwall rail with exclusive separate
temperature controls & expansion valve for base and rail

• Exclusive press fit magnetic removable gaskets

• Separate dual control system for rail & base allows

shutting rail off at night for up to 60% energy savings

• Condensing unit with hot gas condensate evaporator

• Hinged louver for panel for easy access to drain

gate valve, rail temperature control and cleaning of
condenser coil

• Exclusive rail drain for easy clean-up

CABINET EXTERIOR: Unit top and raised rail will

be formed from four piece 20 gauge stainless steel with
a 1-1/2” 90˚ nosing/top turndown. The raised refrigerated
rail will be mechanically cooled and shall be provided with
one single opening to allow flexible pan configurations.
The interior of the rail will be constructed of three-piece
construction with coved corners for easy cleaning. Rail
will hold 6” deep pans - not included. The pans will set on
an integral recessed pan ledge (1” at front and 3” at rear)
making clean-up easy without requiring the remova; of any
pan supports. All units provided with hinged removable
stainless steel covers, fabricated from 20 gauge stainless
steel, and supplied with a combination of covers which
allow maximum access to the pans. Unit bottom and
exterior back are galvanized metal. Exterior ends are
finished in stainless steel. New hinged louver for easier
cleaning of the coil and draining the rail. Unit mounted on
6” (overall) high swivel casters (front two with locks).

CABINET BASE INTERIOR: Interior floor, rear

and top shall be anodized aluminum. Base interior ends

and door openings shall be thermoformed high
impact ABS. Each section will be provided with (1)
removable interior epoxy-coated wire shelf. The base
shall be foamed in place polyurethane insulation with a
minimum thickness of 2”.

DOORS: Stainless steel front with easy to grasp

recessed handles. Doors mounted on heavy duty
stainless steel concealed type hinges with pivot
pin in nylon bushing. Door interior is deep drawn
thermoformed high impact ABS with press-fit
replaceable magnetic gaskets, designed for long life
and easy maintenance. Doors are foamed in place
polyurethane insulation.

REFRIGERATION SYSTEM: The system will

utilize R-404a refrigerant and be provided with a hot
gas condensate evaporation system. Dual refrigeration
system with independent controls for the base and the
rail. The base will have a blower coil with a dedicated
metering device and solenoid valve allowing the
thermostatic control to independently control the base
temperature. The raised mechanically cooled rail will
be controlled utilizing an expansion valve metering
device with its own solenoid valve and thermostat. An
on/off switch, located directly behind the hinged louver,
is provided as standard to allow the rail to be shut
off independently of the base. A pressure control is
provided to monitor the dual systems performance.

ELECTRICAL: The units will be provided with a

8’ power cord and 3-wire grounded plug as standard,
pre-wired for 115 volt, 60 hertz, single phase
operation. Export voltages are available and require
hard wiring in the field to the units main junction box,
(unit will be shipped on legs for export applications,
unless specified otherwise).

This equipment is intended for use in rooms having an
ambient temperature of 86˚F (30˚C) or less.

ORIGIN OF MANUFACTURE: Designed and

manufactured in the United States.

QTY:

MODEL NO:

AIA NO:

SIS NO:

CSI SECTION: 11400

8000N Raised rail preparation tables.
Model 8268N shown.

OPTIONS/ACCESSORIES:

Patented triple or double

drawer cartridges for 27”

openings
Overshelf assembly
Cutting boards
Stainless steel back
Legs in lieu of casters
Pull-out catch pan assemblies
Tray racks for 18 x 26 sheet

pans for 24” or 27” openings

Prep Tables

PPSPEC0006 RevA

Revised 10/13

27" REFRIG.

HINGED

8000N

P
A
N
E
L

24" REFRIG.24" REFRIG.

27" REFRIG. 27" REFRIG.

21" REFRIG.24" REFRIG. 24" REFRIG.

HINGED LOUVER

PANEL

48"

27" REFRIG. 27" REFRIG.27" REFRIG.

95"

HINGED LOUVER

PANEL

HINGED LOUVER

PANEL

60"

HINGED LOUVER

PANEL

68"

24" REFRIG.24" REFRIG.24" REFRIG. 21" REFRIG.

HINGED LOUVER

111"

PANEL

HINGED LOUVER

83"

35"

PANEL

42.9"

33"

DOOR OPENING SIZE- INTERIOR DEPTH

Door

Width

Clearance

(Lt to Rt)

Clearance

(Tp to Btm)

Interior depth

behind door

21” 16” 22.25” 26”

27” 22” 22.25” 26”

24” 19” 22.25” 26”

Model L W H Doors Storage Cu. Ft. Pan Capacity HP Volt Amps NEMA BTU Rating Ship Wt.

8148N 48” 33” 42.9” (1)27” 9.0 (6)1/3 1/3 115/60/1 9 5-15P 1380 342

8260N 60” 33” 42.9” (2)24” 14.67 (8)1/3 1/3 115/60/1 9 5-15P 1380 400

8268N 68” 33” 42.9” (2)27” 17.76 (9)1/3 1/3 115/60/1 9 5-15P 1380 428

8383N 83” 33” 42.9” (2)24”,(1)21” 23.55 (10)1/3 1/3 115/60/1 12 5-15P 2385 550

8395N 95” 33” 42.9” (3)27” 28.18 (12)1/3 1/3 115/60/1 12 5-15P 2385 600

84111N 111” 33” 42.9” (3)24”,(1)21” 32.81 (14)1/3 1/3 115/60/1 12.8 5-20P 3350 638

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2013 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.