RAM Dakota 2005 Owner's Manual

SECTION PAGE
Information Provided by:
1
INTRODUCTION
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
4
INSTRUMENT PANEL AND CONTROLS
5
STARTING AND OPERATING
6
WHAT TO DO IN EMERGENCIES
7
MAINTAINING YOUR VEHICLE
8
MAINTENANCE SCHEDULES
9
IF YOU NEED CONSUMER ASSISTANCE
TABLE OF CONTENTS
.............................................................3
..............................7
.........................................147
.................................................193
..............................................271
...............................................289
..................................................347
.........................................367
1
2
3
4
5
6
7
8
9
10
INDEX
....................................................................375
10
Information Provided by:
CONTENTS
Information Provided by:
INTRODUCTION
1
Introduction ........................... 4
How To Use This Manual ..................4
Warnings And Cautions ................... 5
Vehicle Identification Number ............... 5
Vehicle Modifications / Alterations ........... 6
4 INTRODUCTION
Information Provided by:
INTRODUCTION
This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instruc­tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
NOTE: After you read the manual, it should be stored in the vehicle for convenient reference and remain with the vehicle when sold, so that the new owner will be aware of all safety warnings.
When it comes to service, remember that your dealer knows your vehicle best, has the factory-trained techni­cians and genuine Moparparts, and is interested in your satisfaction.
WARNING!
Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod­ucts of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
HOW TO USE THIS MANUAL
Consult the table of contents to determine which section contains the information you desire.
The detailed index, at the rear of this manual, contains a complete listing of all subjects.
WARNINGS AND CAUTIONS
Information Provided by:
This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information. Observe all Warnings and Cautions.
VEHICLE IDENTIFICATION NUMBER
The vehicle identification number (VIN) is found on a stamped plate located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the windshield. This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
NOTE: It is illegal to remove the VIN plate.
INTRODUCTION 5
1
6 INTRODUCTION
Information Provided by:
VEHICLE MODIFICATIONS / ALTERATIONS
WARNING!
Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
CONTENTS
A Word About Your Keys ..................10
Key-In-Ignition Reminder ................10
Sentry Key — If Equipped ................11
Ignition And Steering Lock .................13
Manual Transmissions ...................13
Automatic Transmissions .................14
Illuminated Entry ........................15
Vehicles Equipped With Power Door Locks ....15
Door Locks ............................16
2
Manual Door Locks .....................16
Power Door Locks .....................17
Child Protection Door Lock ...............20
Remote Keyless Entry .....................21
To Unlock The Doors ...................22
To Lock The Doors .....................22
Using The Panic Alarm ..................24
General Information ....................24
Programming Additional Transmitters ........25
8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
Battery Replacement ....................26
Security Alarm System — If Equipped .........27
To Set The Alarm ......................27
To Disarm The System ...................28
Windows .............................29
Power Windows .......................29
Auto Down ..........................30
Window Lockout Switch .................30
Sliding Rear Window ...................31
Wind Buffeting ........................31
Occupant Restraints ......................31
Lap/Shoulder Belts .....................32
Adjustable Upper Shoulder Belt Anchorage ....37
Automatic Locking Mode (If Equipped) ......38
Center Lap Belts .......................38
Seat Belt Pretensioners ...................38
Enhanced Driver Seat Belt Reminder System
(BeltAlert) ...........................39
Seat Belts And Pregnant Women ............40
Seat Belt Extender ......................40
Driver And Right Front Passenger Supplemental
Restraint System (SRS)—Airbags ...........41
Passenger Airbag On/Off Switch – If
Equipped ............................55
Event Data Recorder (EDR) ...............57
Child Restraint ........................59
Engine Break-In Recommendations ...........72
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9
Information Provided by:
Safety Tips ............................73
Exhaust System .......................73
Safety Checks You Should Make Inside The
Vehicle ..............................74
Safety Checks You Should Make Outside The
Vehicle ..............................74
2
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
A WORD ABOUT YOUR KEYS
The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith. If you received your keys without the bag, ask your dealer to give you the number.
NOTE: Integrated keys (key and key fob combined) must be cut by the dealer. The dealer must have cutters that have enough clearance for integrated keys.
Key-In-Ignition Reminder
If you open the driver’s door when the key is in the ignition lock, a continuous chime will sound to remind you to remove the key.
CAUTION!
An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
Information Provided by:
SENTRY KEY — IF EQUIPPED
With this system, an electronically coded ignition key sends a signal to the vehicle electronics. If the electronics recognizes the signal, the vehicle will start and continue to run. If the system does not recognize the signal, the vehicle will start and run for 2 seconds, then shut off. After six unsuccessful attempts at starting, the system will shut down until the correct key is used.
NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is moving 5 mph or more, then all the transmitter buttons are disabled for all keys.
NOTE: The Sentry Key Immobilizer System is not compatible with remote starting systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Additional Sentry Keys or Mobil Speed-pass™ devices held against or immediately adjacent to the ignition key when starting the engine may cause vehicle starting problems. If a problem occurs, remove the Sentry Key from the key-ring and attempt to start the vehicle again. Pagers, cell phones, walkman, etc. will have no effect on this system.
2
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
The Security Lightwill illuminate for about 3 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Lightwill flash continuously to signal that the vehicle has been immobi­lized. If the Security Lightremains on during vehicle operation, it indicates a fault in the system electronics. If this option was ordered, all of the keys provided with your new vehicle have been programmed to the vehicle electronics.
Replacement Keys
NOTE: Only keys that have been programmed to the
vehicle electronics can be used to start the vehicle. Once a Sentry Key has been programmed to a vehicle, it cannot be programmed to any other vehicle.
At the time of purchase, the original owner is provided with a four digit PIN number. This number is required for dealer replacement of keys. Duplication of keys may be performed at an authorized dealer or by using the Customer Key Programming procedure. This procedure consists of programming a blank key to the vehicle electronics. A blank key is one which has never been programmed and needs to be cut.
NOTE: When having the Sentry Key System serviced, bring all vehicle keys to the dealer.
Customer Key Programming
You can program new keys to the system if you have two valid keys by doing the following:
1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds. Turn the ignition back to the OFF position and remove the first key.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
Information Provided by:
2. Insert the second valid key and switch the ignition to the ON position within 15 seconds. After 10 seconds, a chime will sound and the Security Lightwill begin to flash. Turn the ignition back to the OFF position and remove the second key.
3. Insert a blank Sentry Key into the ignition and switch the ignition to the ON position within 60 seconds of having removed the second key. After 10 seconds, a single chime will sound. The Security Lightwill stop flashing, then turn on for 3 seconds; then turn off.
The new Sentry Key has been programmed. Repeat this process to program up to a total of 8 keys.
General Information
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could void the user’s authority to operate the equipment.
IGNITION AND STEERING LOCK
Insert the key fully, and then turn the switch to one of the five illustrated positions. The key can be inserted or withdrawn only in the LOCK position.
Manual Transmissions
When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. To remove the key,
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
depress and hold the release button located between the ignition switch and the instrument panel. Turn the igni­tion key to LOCK and remove the key.
Manual Transmissions
Automatic Transmissions
In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve­hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily. The key can be inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position.
NOTE: The steering wheel will the lock when the key is removed, and the steering wheel is turned around 115 degrees from center clockwise and around 65 degrees counterclockwise.
Automatic Transmissions
Information Provided by:
NOTE: On vehicles equipped with an automatic trans­mission, the key cannot be turned to LOCK until the selector is in the PARK position. Do not attempt to pull the shift lever out of PARK after the key is in the LOCK position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
ILLUMINATED ENTRY
Vehicles Equipped With Power Door Locks
All interior lights will illuminate in the vehicle when the doors are unlocked using the key fob.
The interior lights will remain on for 30 seconds after the last door is closed, or until all doors are closed and either the ignition is turned to the ON position or a key fob LOCK button is pressed.
There is also a battery saver feature that will turn the interior lights off after 8 minutes if the ignition is OFF and a door is left open or the dimmer control is in the interior lights ON position.
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
DOOR LOCKS
Manual Door Locks
All the doors can be “manually” locked from the inside by pushing down the door lock plunger, located at the rear of the door. Both front doors may be opened from the inside with the door lock plunger in the down or locked position.
WARNING!
For personal security and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle.
WARNING!
When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju­ries and death.
Power Door Locks
Information Provided by:
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
2
Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
As a safety feature the doors will not lock when using the door lock switches during the following conditions:
The driver’s door is open while the key is in the ignition.
Automatic Door Locks
If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph (24 km/h).
This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure:
1. Enter your vehicle and Close all doors.
2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure).
3. Place the key into the ignition.
4. Within 10 seconds, cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ).
5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction.
6. A single chime will be heard to indicate the feature has been disabled.
7. To re-activate this feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the above procedure.
Auto Unlock Feature This feature unlocks all the doors of the vehicle when any door is opened. The following must be met:
The Automatic Door Lock feature must be enabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
Information Provided by:
The doors of the vehicle must be locked automatically by the Automatic Door Lock feature.
The vehicle is in P (Park) and the ignition switch is in any key position.
This feature will not operate if any of the conditions above are not met or following has occurred:
Any manual operation of a door lock switch has occurred.
NOTE: This customer programmable feature is enabled when your vehicle is shipped from the assembly plant.
Auto Unlock Feature Programming
Customer Programming sequence to disable or enable:
1. Enter your vehicle and close all doors.
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may be confusing during this program­ming procedure).
3. Insert the key into the ignition.
4. Within 10 seconds, cycle the key from the OFF position to the ON position four times ending in the ON position (do not start the engine).
5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction.
6. A single chime will sound to indicate the feature has been changed.
7. To reactivate the feature, repeat the above steps.
8. If a chime is not heard, program mode was canceled before the feature could be changed. If necessary repeat the above procedure.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
Child Protection Door Lock
To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child­protection door lock system.
To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks. When the system on a door is engaged, that door can only be opened by using the outside door handle even if the inside door lock is in the unlocked position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
Information Provided by:
WARNING!
Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
NOTE: After setting the child protection door lock
system, always test the door from the inside to make certain it is in the desired position.
NOTE: For emergency exit with the system engaged, move the door lock switch to the UNLOCK position, roll down the window and open the door with the outside door handle.
REMOTE KEYLESS ENTRY
2
This system allows you to lock or unlock the doors or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
NOTE: The line of transmission must not be blocked with metal objects.
To unlock the doors:
Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, and the parking lights will flash on twice.
The system can be programmed to unlock all the doors upon the first UNLOCK button press by using the following procedure:
1. Press and hold the LOCK button on a programmed key fob.
2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button. A single chime will sound to indicate that this feature has changed.
3. Release both buttons at the same time.
4. Test the feature while outside of the vehicle, by pressing the LOCK/UNLOCK button on the keyfob.
NOTE: Pressing the LOCK button on the keyfob while you are inside the vehicle will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
To lock the doors:
Press and release the LOCK button on the key fob to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
Information Provided by:
Horn Chirp Programming
The horn chirp feature will be shipped from the assembly plants activated. If desired this feature can be disabled by using the following procedure:
1. Press and hold the LOCK button on the key fob.
2. After holding the LOCK button for four seconds, also press the PANIC button within 6 seconds. A single chime will sound to indicate that this feature has changed.
3. Release both buttons at the same time.
4. To reactivate this feature, repeat the above steps.
5. Test the horn chirp feature while outside of the ve­hicle, by pressing the LOCK button on the key fob with the ignition in the OFF position and the key removed.
NOTE: Pressing the LOCK button on the keyfob, while you are inside the vehicle, will activate the Security
Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
6. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
Flash Lamps with Lock Programming
1. Press and hold the UNLOCK button on the key fob.
2. After holding the UNLOCK button for four seconds, also press the LOCK button within 6 seconds. A single chime will sound to indicate that this feature has changed.
3. Release both buttons at the same time.
4. Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the OFF position, and the key removed.
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps.
Using the Panic Alarm
To activate the Panic mode while the ignition is OFF press and release the PANIC button on the transmitter once. When the Panic mode is activated, the interior lights will illuminate, the headlamps and parking lights will flash, and the horn will sound.
To cancel the Panic mode press and release the PANIC button on the transmitter a second time. Panic mode will automatically cancel after 3 minutes or if the vehicle is started or exceeds 15 mph (24 km/h). During the Panic
Mode, the door locks and remote keyless entry systems will function normally. Panic mode will not disarm the security system on vehicles so equipped.
General Information
This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may be received including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap­proved by the party responsible for compliance could void the user’s authority to operate the equipment.
If your Remote Lock Control fails to operate from a normal distance, check for these two conditions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
Information Provided by:
1. Weak batteries in transmitter. The expected life of batteries is five years.
2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios.
Programming Additional Transmitters
Vehicles will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of eight fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a currently programmed fob.
NOTE: When entering program mode using that fob, all other programmed fobs will be erased and you will have to reprogram them for your vehicle.
Use the Following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key:
1. Enter your vehicle and close all doors.
2. Fasten your seat belt (Fastening the seatbelt will cancel any chiming that may confuse you during this program­ming procedure).
3. Place the key into the ignition.
4. Turn the ignition to the ON position ( Do not start the engine ).
5. Press and hold the UNLOCK button on the key fob.
6. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds.
7. When a single chime is heard release both buttons. The chime is an indication that you have successfully entered program mode. All fobs that are to be programmed must be done so within 60 seconds of when the chime was heard.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
8. Using the fob to be programmed, press and release both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and then release.
9. Press and release the UNLOCK button a single chime will be heard.
10. Repeat steps 8 and 9 to program up to six additional fobs.
11. Turn the ignition to the OFF position.
12. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 seconds, all programmed fobs function normally.
NOTE: If you do not have a programmed transmitter, contact your dealer for details.
Battery Replacement
The recommended replacement battery is CR2032.
1. If the key fob is equipped with a screw, remove the screw. With the transmitter buttons facing down, use a flat blade to pry the two halves of the transmitter apart. Make sure not to damage the elastomer seal during removal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
Information Provided by:
2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol.
3. To assemble the transmitter case, snap the two halves together.
NOTE: If the key fob is equipped with a screw, reinstall and tighten the screw until snug.
SECURITY ALARM SYSTEM — IF EQUIPPED
This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. The horn will sound repeatedly for 3 minutes and the head­lights and security light in the instrument cluster will flash for an additional 15 minutes. The engine will not run until the system is disarmed.
To Set the Alarm:
The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming. The security light in the instrument panel cluster will flash rapidly for about 15 seconds to indicate that the alarm is being set. After the alarm is set, the security light will flash at a slower rate to indicate that the system is armed.
NOTE: If the security light stays on continuously during vehicle operation, have the system checked by your dealer.
2
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
To Disarm the System:
Use the Keyless Entry transmitter to unlock the doors. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors. Check the vehicle for tampering.
The security system will also disarm, if the vehicle is started with a programmed Sentry Key. If an unpro­grammed Sentry Key is used to start a vehicle, the engine will start and run for 2 seconds and then shut down. After six unsuccessful attempts at starting the engine, the system will shut down until the correct key is used. To exit alarming mode, press the RKE Unlock button or start the vehicle with a programmed Sentry Key.
The security alarm system is designed to protect your vehicle; however, you can create conditions where the system will arm unexpectedly. If you remain in the vehicle and lock the doors with the transmitter, the alarm will sound when you pull the door handle to exit.
NOTE: You may accidentally activate the security sys­tem (horn sounds and lights flash) by entering the vehicle without using the key fob to unlock the door(s). The security system can be disarmed with the key fob’s UNLOCK button or by inserting a programmed Sentry Key into the ignition and turning the key to the ON position.
WINDOWS
Information Provided by:
Power Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29
2
The control on the left front door has up-down switches that give you finger tip control of all four power win­dows. There is a single opening and closing switch on the passenger doors for passenger window control. The windows will operate only when the ignition switch is turned to the ON position and for ten minutes after the
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Information Provided by:
ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer.
NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF.
Auto Down
The driver’s window switch has an Auto Down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the Auto Down movement, operate the switch in either the up or down direction and release the switch.
Window Lockout Switch
The window lockout switch on the driver’s door allows you to disable the window control on the other doors. To disable the window controls on the other doors, press the window lock button. To enable the window controls, press the window control button again.
Loading...
+ 362 hidden pages