RAE Q-2, Q-4 Datasheet

Model Q-2 & Q-4
Two and Four Channel Power Supply
®
Provides two or four unregulated 24 VDC outputs rated at 300 mA
Four input voltage congurations:
• 120 VAC / 50 Hz
• 120 VAC / 60 Hz
• 240 VAC / 50 Hz
• 240 VAC / 60 Hz
Outputs can be paralleled for increased current capacity
Power switch controls input line voltage
Each output is indicated by a super-bright LED
Ordering Information:
Model Q - X (XXXX - XXXX)
50Hz or 60Hz: 50Hz = 50 Hz input voltage frequency, 60Hz = 60 Hz
input voltage frequency 120V or 240V: 120V = 120 VAC input voltage, 240V = 240 VAC input voltage 2 or 4: 2 = Two outputs, 4 = Four outputs
Fits all standard sized card racks
3510 E. ATLANTA AVENUE, PHOENIX AZ 85040 +1.480.968.6407 EDITRAFFIC.COM
Model Q-2 & Q-4 Specications
This is a Performance Specication. It is not intended to be used as Operating Instructions.
General Description: The Model Q-2 and Model Q-4 power supplies transform 120 / 240 VAC, 50 / 60 Hz input power into unregulated 24 VDC. The Model Q-2 has two outputs, the Model Q-4 has four outputs. Each output is rated for 300 mA of load current and can be paralleled (via the rack wiring) for increased current capability. The Model Q-2 and Model Q-4 are available in four input voltage congurations; 120 VAC / 50 Hz, 120 VAC / 60 Hz, 240 VAC / 50 Hz, and 240 VAC / 60 Hz.
Detector Channel Capacity: The Model Q-2 can provide power for up to eight (8) detector channels. The Model Q-4 can provide power for up to sixteen (16) detector channels. Detector channel capacity ratings are per NEMA TS 1 / TS 2 standards.
Output Indicators: Each output circuit has a high intensity, red light emitting diode (LED) that provides an indication of the output status. The indicators are illuminated when the circuit output voltage is greater than or equal to 20.0 ±0.2 VDC and are extinguished when the circuit output voltage is less than 20.0 ±0.2 VDC.
Power Switch: A power switch mounted on the front panel controls the input line voltage.
Fuse Protection: Each output circuit is protected by a 0.375 Amp fuse mounted in a PC
board mounted fuse holder. The Model Q-2 has two (2) fuses, the Model Q-4 has four (4) fuses.
Circuit Board: Printed circuit boards are 0.062 inch thick FR4 material with 2 oz. copper on both sides and plated through holes. Circuit boards and components are conformal coated with polyurethane.
Connector: 2 x 22 contact edge card connector with 0.156 inch (0.396 cm) contact centers. Key slots located between pins B/2 & C/3, E/5 & F/6, and M/11 & N/12. (See Pin Assignments table.)
Operating Temperature: -40º F to +180º F (-40º C to +82º C).
Weight: Model Q-2: 1.50 lb (0.68 kg).
Model Q-4: 2.65 lb (1.20 kg).
Size: 4.50 inches (11.43 cm) high x 2.00 inches (5.08 cm) wide x 6.88 inches (17.48 cm) deep (including connector, excluding handle). Handle adds 1.00 inches (2.54 cm.) to depth measurement.
Pin Assignments
PIN
1 & A DC Common DC Common 2 & B Output 1 (+24 VDC) Output 1 (+24 VDC) 3 & C Output 2 (+24 VDC) Output 2 (+24 VDC) 4 & D No Connection No Connection 5 & E No Connection No Connection 6 & F No Connection No Connection 7 & H No Connection No Connection 8 & J No Connection No Connection 9 & K No Connection No Connection
10 & L Chassis Ground Chassis Ground 11 & M AC Neutral AC Neutral 12 & N AC Line AC Line
13 & P No Connection No Connection
14 & R No Connection No Connection
15 & S No Connection No Connection
16 & T No Connection No Connection 17 & U No Connection Output 3 ( +24 VDC)
18 & V No Connection Output 4 (+24 VDC) 19 & W No Connection No Connection
20 & X No Connection No Connection
21 & Y No Connection No Connection
22 & Z No Connection No Connection
Model Q-2 Model Q-4
Function
Model Q-2 & Q-4 (551-1702-00) 03/23/2020
© COPYRIGHT 2020. Eberle Design, Inc. All Rights Reserved.
Loading...