Rac RACHP221 Instruction Manual
2000W Pressure Washer
RACHP221
Always Read Instruction Manual
Retain for Future Reference
-1-
SAFETY AND WARNING INFORMATION
Read and retain these instructions for future reference.
WARNING:
Read the instructions fully before using the product for the rst time.
Failure to follow the instructions may result in re, electric shock and or serious injury.
We recommend the user wears safety equipment during use.
We recommend the product be used with a RCD (Residual Current Device) with a trip current of 30mA.
Disconnect from the electrical power supply before carrying out any user maintenance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
• When operating the unit in high pressure mode the lance may cause kickback. Therefore please ensure that
you hold the spray gun rmly. When using the unit we recommend that other people are at least 10m away
from the working area.
• High-pressure jets can be dangerous if misused. The jet MUST NOT be directed at yourself, other people,
animals, live electrical equipment or the pressure washer itself. The trigger gun safety lock prevents the
trigger from accidentally being engaged. This safety feature does not lock trigger in the ‘on’ position.
• Do not use the pressure washer if the supply cord or other important parts are damaged (e.g. high pressure
lance or hoses). Never carry your pressure washer by the cord.
• Do not disconnect the high-pressure hose whilst the system is under pressure. This system is capable of
producing 1500PSI. To avoid rupture and injury, do not operate this pump with components rated less than
1500PSI working pressure (including but not limited to spray guns, hose and hose connections.)
• Do not use acids or ammable liquids in the machine.
• When using a pressure washer always ensure that your water connection is protected by a backow
preventer (as per water byelaws). This will avoid possible contamination of your water supply. Use cold water
feed only.
• Protect the unit against freezing; avoid storing the machine where it may be susceptible to frost.
• •Prior to starting the pressure washer in cold weather, be sure ice has not formed in any part of the
equipment.
• The unit must continuously run with water. Dry running will cause serious damage to the seals.
• The water supply hose must be at least 12.5mm (½”) in diameter with a minimum recommended length of 7.5
meters and be tted with a suitable coupling that matches the male quick t connector.
• Use only original spare parts from the manufacturer or approved by the manufacturer.
WARNING: High pressure hoses, ttings and couplings are important for the safety of the appliance. Only use
hoses, ttings and couplings recommended by the manufacturer.
IMPORTANT: The pressure washer is equipped with an auto stop device. When the trigger is released it will
open the power circuit to the motor and cause the pressure washer motor to stop. The motor will resume when
the trigger is pulled. The pressure washer is also equipped with a main power ON/OFF switch located on the
unit. It should always be moved to OFF position when the pressure washer is not being used.
This Product is a class I product, Only a qualied person should carry out servicing.
If an extension lead is to be used with this product, please ensure:
• Use only extension leads that are intended for outdoor use and the plug and socket are of a watertight
construction.
• Completely unwind the cable from the drum to allow for full current rating of the extension lead.
• To reduce the risk of electrocution, keep all connections dry and off the ground.
• Do not touch the plug with wet hands
Warning: Inadequate extension leads can be dangerous.
NEVER START-UP A FROZEN MACHINE.
Frost damages are not covered by the guarantee!
-2-
COMPONENTS
COMPONENT LIST:
1. Handle
2. Mains cable holder
3. Trigger gun holder
4. Mains cable
5. Wheels
6. Mains water supply inlet
7. High pressure hose hook
8. On/Off rotary switch
9. High pressure outlet
10. High pressure hose
11. Compact patio cleaner
12a. Quick connector (Female)
12b. Quick connector (Male)
13. Soap dispensor
14. Rotary brush
15. Fixed brush
16. Turbo lance
17. High pressure adjustable spray lance
18. Patio cleaner extension
19. Trigger gun
20. Cleaning needle
21. 2x 25mm xing screws
22. 2x 15mm xing screws
23. Instruction booklet
TECHNICAL SPECIFICATIONS:
Model:
Net Weight:
Voltage:
Rated input power:
Protection class
Degree of protection:
Input Fuse Size:
YLQ5.23SC-150
12Kg
220 - 240V AC ~ 50Hz
2000W
II
IPX5
13A
Rated pressure:
Max pressure:
Rated ow:
Rated temperature:
Max. inlet pressure:
Sound pressure level LpA:
Sound pressure level LwA:
Hand-arm vibration:
110Bar (11MPa)
150Bar (15MPa)
6.67 l/min
0-40ºC
0.7MPa
77dB(A)
92dB(A)
1.8m/s
6
13
2
21 22
1
12b12a
4
3
7
8
9
17
18
20
19
5
15
14
16
11
10
23
-3-
UN-PACKING AND ASSEMBLY
Unpack the box carefully retaining all of the
packaging until you have checked the contents to the
list on page 2.
Your pressure washer has been factory tested. Due
to this, you may nd that there is a residue of water
inside the unit.
NOTE: Before carrying out any assembly or
disassembly of the unit please ensure that the unit is
not connected to the electrical supply.
Mounting the handle and Hose Holder
1. Assemble the handle (1) by slotting it into the top
of the pressure washer and securing it using the
2x 25mm screws (21).
2. Assemble the High Pressure Hose Hook (7) and
secure it using the 2x 15mm screws (22).
Assembly of the Patio Cleaner
Components: (No. 11 in IB)
1. Connector (Fig 1)
2. Cleaner Head (Fig 2)
3. Spinner (Fig 3)
Assembly:
1. Place the Connector (1) on top of the Cleaner Head (2) (g 4). There are two holes, one small and
one large.
2. Place the threaded stud on the connector (1) (g 1), through the large hole (g 5).
3. Push the pipe on the Spinner (3) (g 6) into the hole on the connector (1) (g 5).
4. Turn the knob (g 6) clockwise until tight. Do not over tighten. See g 7 for assembled unit.
21
22
7
1
9
6
4
2 3
7
1
Threaded stud
5
Hole for pipe
Threaded stud
6
Knob Pipe
Loading...