Rac HP214, RAC-HP214 Instruction Manual
2000W Induction Motor Pressure Washer
RAC-HP214
Always Read Instruction Manual
Retain for Future Reference
SAFETY AND WARNING INFORMATION
Read and retain these instructions for future reference.
General Safety Rules
WARNING:
Read the instructions fully before using the product for the rst time.
Failure to follow the instructions may result in re, electric shock and or serious injury.
We recommend the user wears safety equipment during use.
We recommend the product be used with a RCD (Residual Current Device) with a trip current of 30mA.
Disconnect from the electrical power supply before carrying out any user maintenance.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental •
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance.
When operating the unit in high pressure mode the lance may cause kickback. Therefore please ensure that •
you hold the spray gun rmly. When using the unit we recommend that other people are at least 10m away
from the working area.
High-pressure jets can be dangerous if misused. The jet MUST NOT be directed at yourself, other people, •
animals, live electrical equipment or the pressure washer itself. The trigger gun safety lock prevents the trigger
from accidentally being engaged. This safety feature does not lock trigger in the ‘on’ position.
Do not use the pressure washer if the supply cord or other important parts are damaged (e.g. high pressure •
lance or hoses). Never carry your pressure washer by the cord.
Do not disconnect the high-pressure hose whilst the system is under pressure. This system is capable of •
producing 1800PSI. To avoid rupture and injury, do not operate this pump with components rated less than
1800PSI working pressure (including but not limited to spray guns, hose and hose connections.)
Do not use acids or ammable liquids in the machine.•
When using a pressure washer always ensure that your water connection is protected by a backow preventer •
(as per water byelaws). This will avoid possible contamination of your water supply. Use cold water feed only.
Protect the unit against freezing; avoid storing the machine where it may be susceptible to frost.•
Prior to starting the pressure washer in cold weather, be sure ice has not formed in any part of the equipment.•
The unit must continuously run with water. Dry running will cause serious damage to the seals.•
The water supply hose must be at least 12.5mm ( ½”) in diameter with a minimum recommended length of 7.5 •
meters and be tted with a suitable coupling that matches the male quick t connector.
Use only original spare parts from the manufacturer or approved by the manufacturer.•
WARNING: High pressure hoses, ttings and couplings are important for the safety of the appliance. Only use
hoses, ttings and couplings recommended by the manufacturer.
IMPORTANT: The pressure washer is equipped with an auto stop device. When the trigger is released it will
open the power circuit to the motor and cause the pressure washer motor to stop. The motor will resume when
the trigger is pulled. The pressure washer is also equipped with a main power ON/OFF switch located on the
unit. It should always be moved to OFF position when the pressure washer is not being used.
This Product is a class I product, Only a qualied person should carry out servicing.
If an extension lead is to be used with this product, please ensure:
Use only extension leads that are intended for outdoor use and the plug and socket are of a watertight •
construction.
Completely unwind the cable from the drum to allow for full current rating of the extension lead.•
To reduce the risk of electrocution, keep all connections dry and off the ground.•
Do not touch the plug with wet hands•
Warning: Inadequate extension leads can be dangerous.
-1-
COMPONENTS
Component List
1. Detergent container
2. Water supply inlet
3. ON/OFF switch
4. High pressure outlet
5. Trigger gun
6. High pressure hose
7. Rotary brush
8. Fixed brush
9. Lance extension
10a. Lance rest
10b. Lance holder
11. Adjustable lance
12. Cleaning needle
13. Compact patio cleaner
14. Quick connector (Female)
15. Quick connector (Male)
16. Cable holder
17. Turbo lance
Technical specication
Rated voltage:
Rated power:
Protection class:
Degree of protection:
Permissible pressure:
Rated pressure:
Inlet pressure:
220-240VAC ~ 50Hz
2000W
I
IPX5
16.5 Mpa / 165 Bar
11.0 Mpa / 110 Bar
1.5 - 4 Bar
Supply water temperature:
Nozzle spray angle:
Max output ow rate:
Net weight (machine only):
Cable length:
Hose length:
Noise value:
Noise value:
0-50°C
0 – 90 degree
6.0L/min
13.2Kg
5m
6m
89 db Lwa
84 db Lpa
-2-
1
3
2
4
6
13
10a
10b
16
17
5
7
9
8
14
12
11
15
5
5
9
UN-PACKING AND ASSEMBLY
Unpack the box carefully retaining all of the packaging until you have checked the contents to the list on
page 2.
Your pressure washer has been factory tested. Due to this, you may nd that there is a residue of water
inside the unit.
Assembling
NOTE: Before carrying out any assembly or disassembly of the unit please ensure that the unit is not
connected to the electrical supply.
1. Lance rest (10a) and the lance holder (10b) are supplied loose and needs to be tted, Fig 1. There is
a screw to hold each in place.
2. Connect the trigger gun (5) to the high pressure hose using two 17mm spanners (not supplied), Fig 2.
Note: Using a spanner on the trigger gun connector and a spanner on the hose connector ensures
that you do not stress the internal components when tightening (spanners not included).
3. Remove the black protection cover from the high pressure outlet and connect the high pressure hose
(6) to high pressure outlet (4) as shown in Fig 1.
4. Fit the lance extension (9) into the trigger gun (5) by pushing the lance extension into the trigger gun
and locating the lugs, at the same time turn clockwise to lock into position, Fig 3.
5. Fit the adjustable lance (11) into the lance extension (9) by
pushing the adjustable lance into the lance extension and
locating the lugs, at the same time turn clockwise to lock into
position.
Note: Do not t lances when the power is on.
Note: The adjustable lance (11) and the turbo lance (17) cannot
be tted into the trigger gun (5) and must be used in conjunction
with the lance extension (9).
6. Remove the black protection cover from the water inlet supply.
Fit the quick connector male part (15) to the water inlet supply, as
per Fig 4 and make sure it is fully tightened (do not over tighten).
7. Connect the quick connector female part (14) to your garden
hose. Connect your garden hose to the washer by pushing on the
female part (14) to the male part (15) until it clicks into position as
per Fig 5. To remove the hose, pull back the orange collar.
8. Connect your hose to the water supply as per g 6. Always
ensure you have a good water supply & there are no kinks in the
hose.
-3-
Mains supply
hose adaptor,
not supplied
Fig 2
Fig 4 Fig 5 Fig 6
Fig 3
14
15
Fig 1
4
6
Loading...