Page 1
QUATECH, INC.
Version 1.10, 02.05.04
User’s Manual
SSCFSSCF--100 & SSCFR100 & SSCFR--100100
One Port RS-232 Serial
CompactFlash Cards
5675 Hudson Industrial Parkway
Hudson, Ohio 44236
TEL: (330) 655-9000
FAX: (330) 655-9010
http://www.quatech.com.
CompactFlash Card
User’s Manual P/N: 940-0188-110
- 1 -
Page 2
(c) 2003-2004, Quatech, Inc. This manual is copyrighted. All rights
Copyright
Feedback
are reserved. The information contained in this document cannot be
reproduced in any form without the written consent of Quatech, Inc.
Likewise, any software programs that might accompany this
document can be used only in accordance with any license
agreement(s) between the purchaser and Quatech, Inc. Quatech Inc.
reserves the right to change this documentation or the product to
which it refers at any time and without notice.
Trademarks
Disclaimer
CompactFlash is a trademark of Sandisk Corporation. IBM®, PC®,
and PC-AT® are trademarks of the International Business Machines
Corporation. Windows®, Windows 95®, Windows 98®, Windows
NT®, Windows 2000®, Windows Me®, Windows XP®, Windows Ce®
and MS-DOS® are trademarks of the Microsoft Corporation. All other
trademarks or registered trademarks are property of their respective
owners.
The authors have taken due care in the preparation of this document
and every attempt has been made to ensure its accuracy and
completeness. In no event will Quatech, Inc. be liable for damages of
any kind, incidental or consequential, in regard to or arising out of
the performance or form of the materials presented herein or in any
software program(s) that may accompany this document.
Changes or modifications to this device not explicitly approved by
Quatech will void the user's authority to operate this device.
Quatech, Inc. encourages and appreciates feedback concerning this
document. Please send any written comments to the Technical
Support department at the address listed on the cover page of this
manual.
- 2 -
Page 3
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
Table of contents
1. Overview.............................................................................................................................................4
2. About the SSCF-100/SSSCFR-100.....................................................................................................4
3. Installing the SSCF-100/SSCFR-100.................................................................................................5
3.1 Windows CE, Pocket PC................................................................................................5
3.2 Windows 95/98/Me/2000/XP ..........................................................................................5
3.3 DOS and Windows 3.1...................................................................................................5
4. Register Interface...............................................................................................................................5
5. Hardware Specification......................................................................................................................6
5.1 Pinout ............................................................................................................................6
5.2 Electrical........................................................................................................................7
5.3 Power Consumption.......................................................................................................7
5.4 Mechanical.....................................................................................................................7
5.5 Environmental...............................................................................................................7
5.6 Notes on Serial Data Throughput .................................................................................8
5.7 Baud Rate Settings........................................................................................................8
6. Warranty............................................................................................................................................9
- 3 -
Page 4
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
1. Overview
The SSCF-100 / SSCFR-100 cards are RS-232 Serial cards with the following features:
• Type I CompactFlash form factor for CF+ equipped PDAs, Handheld, Laptop, & Tablet PCs
• DOS, Windows 95, 98, 98SE, Me, 2000, XP, CE, & PocketPC compatible using standard drivers
• Industry standard 16550 register set
• Transmission rates up to 115.2K Baud as standard.
• Data rates to 921.6 kbps
• 3.3V and 5V compatible
• Full hardware modem control line support
• Compatible with all standard serial communication software
• Compatible with standard PCMCIA slots using CompactFlash Adapter (not included)
• Uses host supply pin instead of “RI” for powering external devices
• Standard PC IO port decode for COM1 to COMn
• “Any”IO port and interrupt decode option for best PNP flexibility
• ESD protected RS-232 ports.
• Available with detachable (SSCF-100) or attached (SSCFR-100) cable
• Software controlled power management.
• Low power consumption.
• Supplied with 300mm DB9-male terminated cable with standard” com port pin-out.
2. About the SSCF-100 / SSCFR-100
The SSCF-100 / SSCFR-100 are RS-232 serial cards implemented with 16550 compatible UART
ASIC devices. The serial data and control lines are buffered using ESD protected RS-232 drivers.
Industry standard baud rates up to 115.2K baud are supported, together with 16-byte deep TX and
RX FIFOs. A small switch is located at the back edge of the card, which allows selection of “x1” or
“x8” baud rate multiplier. This feature allows up to 921KBaud operation without needing special
device drivers on the host (in x8 mode you simply multiply the setting shown on the host by 8 to get
the real serial data rate e.g. 19200Baud set on host with x8 mode gives 153600Baud true rate in
hardware). See section 5 for the switch settings.
The SSCF-100 / SSCFR-100 conforms to the industry standard CompactFlash+ interface that allows
connection of peripherals to the system bus of a laptop, tablet, handheld PC or PDA. The CF+
specification extends the earlier memory-only CompactFlash interface to allow I/O devices and extra
power for the card. The SSCF-100 / SSCFR-100 is an I/O type device and therefore requires a CF+
capable slot.
- 4 -
Page 5
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
3. Installing the SSCF-100 / SSCFR-100
3.1 Windows CE, PocketPC
There is no need to install any software for Windows CE or PocketPC. Simply insert the SSCF100/SSCFR-100 card and it will appear in a list when you set up a “Connection.”For more
information about setting up a “Connection” see the manual for your handheld device.
3.2 Windows 95, 98, 98SE, Me, 2000, XP
The “generic” serial drivers in these Operating Systems support the SSCF-100/SSCFR-100. Before inserting the
card, however, execute the SERIALSETUP.EXE program provided on the Quatech Data Communication CD in the
Serial Port Adapters\Drivers\Windows 95, 98, Me, 2000, XP for CompactFlash directory.
3.3 DOS & Windows 3.1x
Operation in DOS or Windows 3.1 requires 3rd party Card and Socket Services drivers to be properly
installed and configured. Follow your software vendor’s instructions on how to do this.
The SSCF-100/SSCFR-100 requires no extra drivers to operate in DOS. Insertion of the card should
create a familiar “happy beep” as the host software configures the card as a standard DOS COM
port. Resource allocation and troubleshooting is all related to the 3rd party software and any issues
that may arise during configuration should be addressed to the vendors of this software. The SSCF100/ SSCFR-100 have been tested with: SystemSoft Cardware and Award Cardwizard
4. SSCF-100 Register Interface
The SSCF-100 and SSCFR-100 both appear as 5V cards to the host system because Vs1 and Vs2 are
not connected. Thus the host defaults to 5V when possible to provide the strongest RS-232 output
signals, and therefore the best noise margins. The Card Information Structure (CIS) does not define
any 3.3V tuples because some platforms will also take this as a sign to run at 3.3V even when 5V is
available. On a PDA or HPC, the host will power the card at 5V if it is available, or at 3.3V if that is
the only option (despite there being no 3.3V tuple entries).
- 5 -
Page 6
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
5. Hardware Specification
5.1 PINOUT
The SSCF-100 is supplied with a 300mm long detachable Type45 cable that terminates with a DB9
Male connector with female screw-locks (to match the port at the back of a PC). The pin-out below
applies to both the SSCF-100 / SSCFR-100 card and the DB9 male connector on the supplied cable
(the cable is pinned one-to-one).
The SSCFR-100 has a permanently attached 300mm cable with the same type of DB9 connector
described above.
PIN NAME Function
1* DCD Data Carrier Detect input
2 RX Receive Data input
3 TX Transmit Data output
4 DTR Data Terminal Ready output
5 GND GROUND (0V)
6 DSR Data Set Ready input
7 RTS Request To Send output
8 CTS Clear To Send input
9 RI Ring Indicate input
*Pin 1 is nearest the edge of the card.
For ref: mating connector type: Honda rmc-e9f2s-bsla2n-a2
x8
x1
SSCF-100 / SSCFR-100 with Baud Rate Multiplier Switch
PIN 9 PIN 1
- 6 -
Page 7
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
5.2 ELECTRICAL
All figures quoted are typical parameters @ 25°C
RS-232 SIGNALS: Typical output level ±5.5V (open circuit voltages)
ESD PROTECTION: All RS-232 signal lines on the SSCF-100 / SSCFR-100 card are
protected against electrostatic discharge (ESD)
• 15kv - human body model
• 8kv - IEC1000-4-2, contact discharge
• 15kv - IEC1000-4-2, air-gap discharge
UART CLOCK SPEED: x1: UART CLOCK is 1.8432MHz ->115.2KBaud max
x8: UART CLOCK is 14.7456MHz->921.6KBaud max
5.3 POWER CONSUMPTION
All figures quoted are typical parameters @ 25°C
VCC CURRENT: 20mA typical @ 5V, 13mA typical @ 3.3V
IN STANDBY MODE: 14mA typical @ 5V, 5mA typical @ 3.3V
5.4 MECHANICAL
CARD MASS: 10g typical.
FORM FACTOR: 36.4mm x 42.8mm x 3.3 mm overall card size
SSCF-100 CABLE: Detachable 300mm cable with DB-9 male connector
SSCFR-100 CABLE: Attached 3.9mm thick cable protrudes 10.3mm from the back edge
of the card. The oval cable measures approx. 7mm x 1.7mm with
shield and 9x 7/0.1mm conductors.
5.5 ENVIRONMENTAL
HUMIDITY: <80% non-condensing
TEMP: 0-50°C ambient
- 7 -
Page 8
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
5.6 NOTES ON SERIAL DATA THROUGHPUT
The maximum serial baud rate of 921KBits/sec does not imply that the maximum sustained
throughput rate of the serial port will be as high. The actual throughput rate that can be achieved
depends on many factors including the host PC speed, the serial data source’s data block size and
whether the blocks are “back-to-back”, whether the interrupt in use on the host is being shared by
other devices leading to increased latency, etc.
As a simple rule of thumb, using the standard serial drivers on a fast PC will allow throughput rates
of 400-600KBits/sec, although these rates can’t be guaranteed and will be application specific.
5.7 BAUD RATE SETTINGS
The table below illustrates the common baud rate values available for each of the baud rate
multiplier switch positions:
HOST SETTING SWITCH = x1 SWITCH = x8
300 300 2400
1200 1200 9600
2400 2400 19200
4800 4800 38400
9600 9600 76800
19200 19200 153600
38400 38400 307200
57600 57600 460800
115200 115200 921600
- 8 -
Page 9
Quatech CompactFlash Card User’s Manual SSCF-100 / SSCFR-100
6. Warranty information
Quatech, Inc. warrants the SSCF-100 / SSCFR-100 to be free of defects for five (5) years from the
date of purchase. Quatech, Inc. will repair or replace any board that fails to perform under normal
operating conditions and in accordance with the procedures outlined in this document during the
warranty period. Any damage that results from improper installation, operation, or general misuse
voids all warranty rights. No representation is made regarding the suitability of this product for any
particular purpose.
Please complete the following information and retain for your records.
DATE OF PURCHASE: ____________________________
MODEL NUMBER: SSCF-100 / SSCFR-100
PRODUCT DESCRIPTION: One Port RS-232 CompactFlash Card
SERIAL NUMBER: ____________________________
All products returned to Quatech for either warranty or non-warranty repair MUST be assigned a
Returned Material Authorization (RMA) number prior to shipment. This RMA number must be
clearly marked on the exterior of the product’s return packaging and in any correspondence to
ensure proper routing and prompt attention. To obtain an RMA number, contact Quatech Technical
Support Department at 1-800-553-1170 or (330) 655-9000 or complete the RMA request form on the
Quatech website. In order to prevent damage to returned merchandise during shipment, please
package electronic components in anti-static/shock proof materials.
For warranty repair/returns, please have the following information available when contacting the
Technical Support department:
1. Model number and serial number of the product under warranty
2. Repair instructions and/or specific description of the problem
For non-warranty repairs or upgrades, contact the Technical Support department for current
repair charges. Please have the following information available when you call:
1. Purchase order number to cover the cost of the service
2. Model number and serial number of the product
3. Repair or upgrade instructions relative to the product
- 9 -
Loading...