Viking: 50-pin Single Ended
SCSI Jumper Settings
Jumper Settings
The following describes the jumper options and settings available on the Maxtor® Viking™
disk drive. For more detail on jumper definitions; please refer to the jumper definition
section.
The Maxtor Viking was developed by Quantum Corporation prior to its merger with Maxtor.
Termination Enable (TE)
Enable termination
Disable termination
TE jumper on
TE jumper off
Termination Power (TP)
Enable termination power
Disable termination power
TP jumper on
TP jumper off
SCSI ID (A2, A1, A0)
Set drive SCSI ID
See ID settings table below
1 of 1
Viking: 50-pin Single Ended
SCSI Jumper Settings
Wait Spin (WS)
Enable spin delay
Disable spin delay
Spin Delay (SD)
Enable spin delay
Disable spin delay
Jumper Locations
The Viking disk drive has two locations where user configurable jumpers are found. The primary
jumper block (Front option connector J3) for the Viking is found on the front edge of the disk drive
printed circuit board. Using these jumper pins you can establish the various drive configuration
options. The second option jumper block is used to set the Viking termination options. This jumper
block is found on the printed circuit board at the rear of the drive and is near the SCSI cable
connector.
WS jumper on
WS jumper off
SD jumper on
SD jumper off
Pin
1
3
5
7
9
11
13
15
17
19
Signal
A0
A1
A2
RSVD1
TE
LEDPWR
Wait Spin
Spin Delay
RSVD2
RSVD3
Pin
2
4
6
8
10
12
14
16
18
20
Signal
logic_gnd
logic_gnd
logic_gnd
logic_gnd
logic_gnd
LEDPWR
logic_gnd
logic_gnd
logic_gnd
logic_gnd
2 of 2
Viking: 50-pin Single Ended
SCSI Jumper Settings
The drawing above displays the jumper block physical location and pin definitions.
SCSI ID Settings
The following table identifies the various SCSI ID values and the jumper positions required to set
them.
Drive ID
ID 0
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
A0
OFF
ON
OFF
ON
OFF
ON
OFF
ON
A1
OFF
OFF
ON
ON
OFF
OFF
ON
ON
A2
OFF
OFF
OFF
OFF
ON
ON
ON
ON
3 of 3
Viking
:
68-pin Wide Wide Differential
SCSI Jumper Settings
Jumper Settings
The following describes the jumper options and settings available on the Maxtor® Viking™ disk drive.
For more detail on jumper definitions; please refer to the jumper definition section.
The Maxtor Viking was developed by Quantum Corporation prior to its merger with Maxtor.
Termination Enable (TE)
Enable termination
Disable termination
Termination Power (TP)
Enable termination power
Disable termination power
SCSI ID (A3, A2, A1, A0)
TE jumper on
TE jumper off
TP jumper on
TP jumper off
1 of 1
Viking
:
Set drive SCSI ID
Wait Spin (WS)
Enable spin delay
Disable spin delay
Spin Delay (SD)
Enable spin delay
Disable spin delay
68-pin Wide Wide Differential
SCSI Jumper Settings
See ID settings table below
WS jumper on
WS jumper off
SD jumper on
SD jumper off
Jumper Locations
The Viking wide disk drive has two locations where user configurable jumpers are found. The primary
jumper block (Front option connector J3) the Viking wide drive is found on the front edge of the disk
drive printed circuit board. Using these jumper pins you can establish the various drive configuration
options. The secondary option jumper block provides an alternate method for setting primary drive
features. The alternate jumper block is located at the rear of the drive and is incorporated into the
SCSI cable connector.
The termination and termination power option setting, only available on SE (non-differential)
versions, is located on the printed circuit board at the rear of the drive and is near the SCSI cable
connector.
Pin
Pin
2 of 2
Signal
Signal
Viking
:
1
3
5
7
9
11
13
15
17
19
SCSI ID (A0)
SCSI ID (A2)
SCSI ID (A2)
SCSI ID (A3)
Term. Enable (TE) 10
LEDPWR
Wait Spin (WS)
Spin Delay (SD)
RSVD2
RSVD3
2
4
6
8
12
14
16
18
20
68-pin Wide Wide Differential
SCSI Jumper Settings
logic_gnd
logic_gnd
logic_gnd
logic_gnd
logic_gnd
LEDPWR
logic_gnd
logic_gnd
logic_gnd
logic_gnd
Pin
2
4
6
8
12
Signal
Fault LED
logic_gnd
logic_gnd
Busy LED
logic_gnd
(reserved)
Pin
1
3
5
7
9
11
SCSI ID Settings
The following table identifies the various SCSI ID values and the jumper positions required to set
them.
Signal
SCSI ID (A0)
SCSI ID (A1)
SCSI ID (A2)
SCSI ID (A3)
Term. Enable (TE) 10
+5Vdc out
3 of 3
Viking
:
Drive ID
ID 0
ID 1
ID 2
ID 3
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
ID 15
A0
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
A1
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
A2
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
68-pin Wide Wide Differential
SCSI Jumper Settings
A3
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
4 of 4
Loading...