Quadra-Fire LOGS-QFI30FB Log Placement Instructions
Log Set Assembly: LOGS-QFI30FB
LOG PLACEMENT INSTRUCTIONS
Models: QFI30FB, QFI30FB-C, QFI30FB-IFT
5
SRV2221-704
SRV2221-701
2
SRV2221-703
1
SRV2221-707
SRV2221-705
SRV2221-706
SRV2221-702
PILOT BRACKET
LIGHT TRAYS
LOG PIN
7
6
4
3
Figure 1. Logs Installed
GLASS ROCK
GRATE BAR
GRATE TINES
Figure 2. Reference Points for Log Placement
CAUTION: Logs are fragile, handle with care.
Glass Rock (2201-853): Fill each light tray evenly with the glass rock.
WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over
burner ports. Improperly placed glass rock interferes with proper burner operation.
LOG RESTS
AGAINST BACK
OF FIREBOX
1
Figure 3. Install Glass Rock
FLAT SPOT
FOR LOG #6
RECESSED
AREA OF LOG
MATES WITH
BURNER TOP
2
CENTER LOG
OVER PILOT
BRACKET
Figure 4. Place Log #1 Figure 5. Place Log #2
Log #1 (SRV2221-703): Position Log #1 as shown in Figure 4. See Figure 2 for additional points of reference. Center the
log over the pilot bracket. Pull the log forward until contact is made with burner.
Log #2 (SRV2221-701): Position Log #2 as shown in Figure 5. See Figure 2 and Figure 6 for additional points of reference.
The recessed area on the bottom of the log and the back right corner of the burner top mate.
Quadra-Fire • LOGS-QFI30 Log Instructions • 2221-935 Rev. E • 6/18
1
FRONT
RECESSED AREA
FLAT SPOT
FOR LOG #5
LOG TOUCHES
FIREBOX
2
BACK
Figure 6. Log #2
Log #3 (SRV2221-702): Position Log #3 as shown in Figure 7. See Figure 2 and Figure 8 for additional reference points.
Mate the base of the left grate tine with the groove located on the bottom of the log. Pull the log forward until it stops against
the vertical portion of the grate tine. Swing the rear of the log counterclockwise until it touches the rebox.
BASE OF GRATE TINE FITS IN GROOVE
BASE TINE
Figure 7. Place Log #3
MATE LOG PIN
WITH LOG SLOT
3
MATE GRATE TINE
WITH LOG SLOT
3
4
FRONTBACK
Figure 8. Log #3 - Bottom View Figure 9. Place Log #4
Log #4 (SRV2221-706): Position Log #4 as shown in Figure 9. See Figure 2 and Figure 10 for additional references. Mate
the grate tine slot with the base of the right grate tine. The grate tine slot is located on the bottom right end of Log #4. See
Figure 10. Slide the right end of the log forward until the tine fully engages the slot. Mate the log pin slot with the right log pin.
GRATE TINE SLOT
4
LOG PIN SLOT
LOG GROOVE FOR LOG #7
FLAT SPOT FOR LOG #6
5
LEFT
RIGHT
Figure 10. Log #4 - Bottom View
Log #5 (SRV2221-704): Position Log #5 as shown in Figure 11. See Figure 2 and Figure 12 for additional references.
Rest the left end of Log #5 on the at spot indicated in Figure 7. Locate right end of log against the grate and to the left of
the log pin. Ensure the nose of the log does not cover any burner ports.
Figure 11. Place Log #5
Quadra-Fire • LOGS-QFI30 Log Instructions • 2221-935 Rev. E • 6/182
Loading...