QT HCPL-2630, HCPL-2611, HCPL-2601, 6N137, HCPL-2631 Datasheet

0 (0)

HIGH SPEED-10 MBit/s

LOGIC GATE OPTOCOUPLERS

SINGLE-CHANNEL	DUAL-CHANNEL
6N137	HCPL-2630
HCPL-2601	HCPL-2631
HCPL-2611

DESCRIPTION

The 6N137, HCPL-2601/2611 single-channel and HCPL-2630/2631 dual-channel optocouplers consist of a 850 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable output. This output features an open collector, thereby permitting wired OR outputs. The coupled parameters are guaranteed over the temperature range of -40°C to +85°C. A maximum input signal of 5 mA will provide a minimum output sink current of 13 mA (fan out of 8).

An internal noise shield provides superior common mode rejection of typically 10 kV/µs. The HCPL2601 and HCPL2631 has a minimum CMR of 5 kV/µs.

The HCPL-2611 has a minimum CMR of 10 kV/µs.

FEATURES

•Very high speed-10 MBit/s

•Superior CMR-10 kV/µs

•Double working voltage-480V

•Fan-out of 8 over -40°C to +85°C

•Logic gate output

•Strobable output

•Wired OR-open collector

•U.L. recognized (File # E90700)

APPLICATIONS

•Ground loop elimination

•LSTTL to TTL, LSTTL or 5-volt CMOS

•Line receiver, data transmission

•Data multiplexing

•Switching power supplies

•Pulse transformer replacement

•Computer-peripheral interface

N/C 1		8	V
			CC
+	2	7	V
			E
V
F
_	3	6	V
			O
N/C 4		5	GND

Single-channel circuit drawing

TRUTH TABLE

(Positive Logic)

		8
1		1
		1
+	1	8	V
			CC
V
F1
_	2	7	V
			01
_	3	6	V
			02
V
F2
+ 4		5	GND

Dual-channel circuit drawing

Input		Enable	Output

H		H	L

L		H	H

H		L	H

L		L	H

H		NC	L

L		NC	H
	A 0.1 µF bypass capacitor must be connected between pins 8 and 5.
	(See note 1)

8/10/99 200002A

HIGH SPEED-10 MBit/s

LOGIC GATE OPTOCOUPLERS

		SINGLE-CHANNEL			DUAL-CHANNEL
		6N137			HCPL-2630
		HCPL-2601			HCPL-2631
		HCPL-2611


ABSOLUTE MAXIMUM RATINGS (No derating required up to 85°C)

Parameter				Symbol	Value	Units

Storage Temperature				TSTG	-55 to +125	°C
Operating Temperature				TOPR	-40 to +85	°C
Lead Solder Temperature				TSOL	260 for 10 sec	°C
EMITTER					50
DC/Average Forward	Single channel			IF	50	mA
DC/Average Forward	Single channel			IF		mA

Input Current	Dual channel (Each channel)				30

Enable Input Voltage	Single channel			VE	5.5	V
Not to exceed VCC by more than 500 mV				VE	5.5	V
Not to exceed VCC by more than 500 mV

Reverse Input Voltage	Each channel			VR	5.0	V
Power Dissipation	Single channel			PI	100	mW

	Dual channel (Each channel)				45
	Dual channel (Each channel)				45

DETECTOR				VCC
Supply Voltage				VCC	7.0	V
Supply Voltage			(1 minute max)		7.0	V
			(1 minute max)

Output Current	Single channel			IO	50	mA

	Dual channel (Each channel)				50
	Dual channel (Each channel)				50

Output Voltage	Each channel			VO	7.0	V
Collector Output	Single channel			PO	85	mW

Power Dissipation	Dual channel (Each channel)				60
Power Dissipation	Dual channel (Each channel)				60


RECOMMENDED OPERATING CONDITIONS

Parameter		Symbol		Min	Max	Units

Input Current, Low Level		IFL		0	250	µA
Input Current, High Level		IFH		*6.3	15	mA
Supply Voltage, Output		VCC		4.5	5.5	V
Enable Voltage, Low Level		VEL		0	0.8	V
Enable Voltage, High Level		VEH		2.0	VCC	V
Low Level Supply Current		TA		-40	+85	°C
Fan Out (TTL load)		N			8

* 6.3 mA is a guard banded value which allows for at least 20 % CTR degradation. Initial input current threshold value is 5.0 mA or less

8/10/99 200002A

HIGH SPEED-10 MBit/s

LOGIC GATE OPTOCOUPLERS

SINGLE-CHANNEL	DUAL-CHANNEL
6N137	HCPL-2630
HCPL-2601	HCPL-2631
HCPL-2611

ELECTRICAL CHARACTERISTICS (TA = -40°C to +85°C Unless otherwise specified.)

INDIVIDUAL COMPONENT CHARACTERISTICS

Parameter

Test Conditions

Symbol

Min

Typ**

Max

Unit

EMITTER

(IF = 10 mA)

1.8

Input Forward Voltage

TA =25°C

1.4

1.75

Input Reverse Breakdown Voltage

(IR = 10 µA)

BVR

5.0

Input Capacitance

(VF = 0, f = 1 MHz)

CIN

Input Diode Temperature Coefficient

(IF = 10 mA)

#VF/#TA

-1.4

mV/°C

DETECTOR

High Level Supply Current

Single Channel

(VCC = 5.5 V, IF = 0 mA)

ICCH

Dual Channel

(VE = 0.5 V)

Low Level Supply Current

Single Channel

(VCC = 5.5 V, IF = 10 mA)

ICCL

Dual Channel

(VE = 0.5 V)

Low Level Enable Current

(VCC = 5.5 V, VE = 0.5 V)

IEL

-0.8

-1.6

High Level Enable Current

(VCC = 5.5 V, VE = 2.0 V)

IEH

-0.6

-1.6

High Level Enable Voltage

(VCC = 5.5 V, IF = 10 mA)

VEH

2.0

Low Level Enable Voltage

(VCC = 5.5 V, IF = 10 mA) (Note 3)

VEL

0.8

SWITCHING CHARACTERISTICS (TA = -40°C to +85°C, VCC = 5 V, IF = 7.5 mA Unless otherwise specified.)

AC Characteristics

Test Conditions

Symbol

Min

Typ**

Max

Unit

Propagation Delay Time

(Note 4)

(TA =25°C)

TPLH

to Output High Level

(RL = 350 !, CL = 15 pF) (Fig. 12)

100

Propagation Delay Time

(Note 5)

(TA =25°C)

TPHL

to Output Low Level

(RL = 350 !, CL = 15 pF) (Fig. 12)

100

Pulse Width Distortion

(RL = 350 !, CL = 15 pF) (Fig. 12)

"TPHL-TPLH"

Output Rise Time (10-90%)

(RL = 350 !, CL = 15 pF)

(Note 6) (Fig. 12)

Output Fall Time (90-10%)

(RL = 350 !, CL = 15 pF)

(Note 7) (Fig. 12)

Enable Propagation Delay Time

(IF = 7.5 mA, VEH = 3.5 V)

tELH

to Output High Level

(RL = 350 !, CL = 15 pF) (Note 8) (Fig. 13)

Enable Propagation Delay Time

(IF = 7.5 mA, VEH = 3.5 V)

tEHL

to Output Low Level

(RL = 350 !, CL = 15 pF) (Note 9) (Fig. 13)

Common Mode Transient Immunity (TA =25°C) "VCM" = 50 V, (Peak)

(at Output High Level)

(IF = 0 mA, VOH (Min.) = 2.0 V)

"CMH"

V/µs

6N137, HCPL-2630

(RL = 350 !) (Note 10)

10,000

HCPL-2601, HCPL-2631

(Fig. 14)

5000

10,000

HCPL-2611

"VCM" = 400 V

10,000

15,000

(RL = 350 !) (IF = 7.5 mA, VOL (Max.) = 0.8 V)

10,000

Common Mode

6N137, HCPL-2630

"VCM" = 50 V (Peak)

"CML"

V/µs

Transient Immunity

HCPL-2601, HCPL-2631

(TA =25°C)

5000

10,000

(at Output Low Level)

(Note 11) (Fig. 14)

HCPL-2611

(TA =25°C)

"VCM" = 400 V

10,000

15,000

8/10/99 200002A

+ 7 hidden pages