Qsc audio DCP 200 User Manual

DCP 200

Digital Cinema Processor

A Cinema Processor, Booth Monitor and Digital Crossover along with network
control and monitoring of DSP, amplifiers and speakers in one integrated package.

QSC's Digital Cinema Processor, the DCP 200, builds on the legacy of DCM and Basis to
provide all booth-mounted signal processing and monitoring functions for Digital Cinema
systems that use Basis and DCA amps behind the screen. The DCP 200 offers most of
the features of the DCP 300 but at a lower price point for systems that don’t require
screen channel crossovers but instead utilize CobraNet network audio distribution to
additional Basis processors.

Designed to be used with QSC's Digital Cinema Amplifiers (DCA) and featuring
advanced DSP presets for QSC's Digital Cinema Speakers (DCS), the DCP 200
optimizes loudspeaker performance while simplifying cinema sound system wiring and
configuration. The DCP 200 covers cinema systems ranging from three to five screen
channels and up to 16 digital inputs. Outboard Basis processors support passive,
bi-amp, tri-amp or quad-amp crossovers and subwoofer outputs. The DCP 200 is
compatible with all analog cinema processor formats including Dolby® Digital Surround­EX and DTS-ES and features a 10-channel analog input for integration with existing
35 mm audio systems.

Digital Signal Processing

The DCP 200 digital signal processing capability outperforms traditional analog
processors for optimized audio performance. Fader level, 1/3 octave graphic EQ,
parametric equalization, polarity, delay and gain can be precisely adjusted for each
channel in your system. Basis processors provide passive and active 2-way, 3-way and
4-way crossovers.

Less Wiring, Faster Set-up

DCPs greatly simplify system wiring and set-up, significantly reducing installation time
and labor cost. Input to the DCP is provided via standard DB-25 cables from the
D-Cinema server and/or 35mm cinema processor. Connections to DCA amplifiers for
input and monitor signals are made through a single QSC DataPort / VGA-style cable.
All traditional XLR and barrier strip terminations are eliminated. DCPs simplify set-up
by using a menu-driven, PC-based software program for configuration. Connection to
remote-mounted Basis processors is via RJ45 connectors and Cat. 5 cable. Commonly
used configurations can also be saved on a disk, allowing you to quickly load them on
other DCPs. All system configuration data is saved to an SD memory card, allowing easy
transfer of settings to a new DCP, should replacement ever be required.

Advanced Monitor Functions

In addition to audio monitoring of processor inputs and outputs, DCPs include QSC's
exclusive "load fault" detection. DCPs monitor all surround amplifier outputs and indicate
opens and shorts in the speaker system, providing confirmation that all amplifier outputs
are functioning properly. In addition, the DCP detects all amplifier clipping, protect modes
and heat sink temperature for reporting via SNMP or a QSControl Ethernet monitoring
system. QSControl and QSCreator allow for the creation of custom control screens and
remote access for fault reporting and diagnosis. The NAC 100 Ethernet remote control
panel provides remote operation in a multiplex from anywhere on the local network.

Features

• Digital Input for up to 16-Channels of audio

• Networked audio I/O via CobraNet™ — supports
behind-the-screen mounting of Basis processors for
screen channel and subwoofer DCA amplifiers

• Network control and monitoring via SNMP

• Serial automation control via RS-232

• Analog Inputs for film processors, non-sync
and Mic/Line

• Master volume and full 1/3 Octave Graphic EQ on
all channels (except subwoofer)

• Booth Monitor with touch screen control for
easy operation

• DataPorts for surround channel amplifiers

• Compatible with all existing DCA amplifiers —
thousands of DCA equipped screens are ready for
full network monitoring and control

• Dual power supplies with load sharing for seamless
operation in the event of failure

• SD Memory card for quick unit swap — restores
all settings

• Multiple Bypass modes routes audio around failed
components to insure that the show will go on

• QSControl and QSCreator allow for the creation of
custom control screens and remote access for fault
reporting and diagnosis

• Easily integrates with existing film processors for
dual film/digital projection systems

• CobraNet offers digital audio routing via
Basis processors

• Continued development of software and firmware
will add new capabilities to the existing hardware
with easy firmware updates

• The DCP 200 is part of a new generation of QSC
products designed expressly for the needs of
D-Cinema sound systems

DCP 200

Front Panel Controls CobraNet RJ45s 100 Mbps primary/backup network audio

Power switch Rocker switch SD card receptacle Configuration memory card (1 GB min)

Mute control Push button H.I. and V.I. impaired outputs

Auditorium fader Rotary encoder Output stage type Single ended (balanced Z)

Monitor volume/parameter adjust Rotary encoder Output impedance 50 Ohms

Menu-driven LCD Touch control LCD Nominal output level -11.8 dBu (200 mVrms)

Rear Panel Connectors Loading requirements Rmin = 2k Ohms, Cmax = 4nF

D-Cinema input group 1 DB-25 — AES3/EBU channels 1-8 Audio network

D-Cinema input group 2 DB-25 — AES3/EBU channels 9-16 Protocol CobraNet version 2 protocol

Main analog input DB-25 — Analog audio channels 1-8 Data rate 100 Mbps (Fast Ethernet)

Extended surround input DB-25 — DB-25 - Surround and Le/Re Channels Ports 1 Primary, 1 Backup (auto-failover)

Universal Mic/Line input XLR — Mic (+ phantom pwr) or line level Connection requirements

Preliminary Specifications

Cat-5 UTP cable or better (100m maximum length),
direct connection to wired network switch ports only,
dedicated LAN or VLAN

S/PDIF input

RCA (L/R) inputs

DataPort outputs HD-15 (6) — QSC amplifier interface Data rate 10/100 Mbps

Automation inputs

Logic output 4-pin Euro-style (x2) – outbound control

Relay outputs 6-pin Euro-style (x2) – outbound control Dimensions (H/W/D): 5.25" x 19" x 15.2" (133 mm x 483 mm x 386 mm)

Serial Control DB-9 RS-232 Serial Interface Line voltage requirements 100 VAC – 240 VAC, 50/60 Hz

USB Type B port Config and management interface

QSControl RJ45 10/100 Mbps network management

RCA — Stereo digital audio interface

and Lt/Rt Matrix

RCA (2) — Stereo Left and Right

and Lt/Rt Matrix

6-pin Euro-style (x2) – TTL compatible dry
contact closure

QSControl™ network/ SNMP

Protocol

Connection requirements

Weight 16.6 lb (7.5 kg)

Standard TCP/IP implementation over Ethernet or
Fast Ethernet

Cat-5 UTP cable or better (100m maximum length),
direct connection to wired network switch ports only,
dedicated LAN or VLAN

RoHS

All specifications are subject to change without notice.

©2010 QSC Audio Products, LLC. All rights reserved. QSC, the QSC logo, QSControl.net, QSControl, BASIS, RAVE, QSCreator, DCP Manager, Digital Cinema Amplifier (DCA),
Digital Cinema Processor (DCP) and Intrinsic Correction are registered trademarks of QSC Audio Products, LLC in the U.S. Patent and Trademark office and other countries.
Dolby is a registered trademark of Dolby Laboratories. CobraNet is a trademark of Cirrus Logic. All other trademarks are the property of their respective owners. Patents
may apply or be pending.

1675 MacArthur Boulevard • Costa Mesa, CA 92626 • Ph: 800/854-4079 or 714/957-7100 • Fax: [phone]

DCP 100 Spec Sheet 05/26/10

please recycle

qscaudio.com