QSC AD-C.SAT Quick Start Guide
Acoustic Design Series
®
Quick Start Guide
AD-C.SUB
AD-C.SAT
EXPLANATION OF SYMBOLS
The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in
damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.
The term "NOTE" is used to indicate additional useful information.
The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un-insulated "dangerous"
voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans.
The intent of the exclamation point within a triangle is to alert the user to the presence of important safety, and operating and
maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Clean only with a dry cloth.
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
7. Only use attachments/accessories specified by the manufacturer.
8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
9. Do not use this apparatus in or near water or liquids.
10. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into the apparatus.
11. Adhere to all applicable, local codes.
12. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
Maintenance and Repair
Advance technology, e.g., the use of modern materials and powerful electronics, requires specially adapted maintenance and repair methods. To avoid
a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of additional safety hazards, all maintenance or repair work
on the apparatus should be performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible
for any injury, harm or related damages arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
TD-001556-01-A1
*TD-001556-01*
1
Install the AD-C.SUB Subwoofer
What's in the AD-C.SUB Box
(1x)
AD-C.SUB
(1x)
Grille
(3x)
Euro-
style plug
(4-pole)
Cut-Out Template
AD-C.SAT
(2x)
Tile Rails
(1x)
Cutout
(1x)
Terminal Cover
Template
Prepare Ceiling
Refer to Figure 1.
1. Use the supplied Cut-Out template to cut a 12 inch (305 mm) diameter
hole (1) in the ceiling where the loudspeaker is to be installed. For frameconstruction ceiling, skip to "Wire the Loudspeakers".
2. Install two V-rails (2), one on each side of the hole, and supported by the
suspended-ceiling support rails (3).
3. Install the C-ring (4) over the hole, using the V-rails as support. Make sure the
clips on the C-ring are properly fitted over the V-rail.
4. Use sheet-metal screws (5) to secure the C-ring to the V-rails.
Wire the Subwoofer
Refer to Figure 2.
(1x)
C-Ring
(2x)
Tile Rail
Screws
(sheet metal)
(1x)
Warranty
TD-000453
(1x)
Quick Start
Guide
TD-001556
3
4
2
5
1
— Figure 1 —
1. Loosen the two screws (1) holding the wire-terminal cover
(2) to the body of the loudspeaker enclosure.
2. Pull the cover (2) up slightly in front, then pull away from
the enclosure.
3. Pass the wires through the conduit/stress-relief clamp
(3). Leave enough wire for making connections. Carefully
tighten the clamp (3) over the wires, or over the conduit if
it is used.
NOTE: The wire-terminal cover has two
additional openings (4) that you can use if the
factory-selected opening causes conflict between
the wiring and the structure.
4. Wire the female Euro-style plugs as shown in Figure 3.
5. The Euro-style plugs are factory installed. If you remove
the connectors, make sure to re-tighten the screws
to secure the connections.
6. Slide the cover (2) over the connector and under the
two clips, then tighten the two Phillips screws.
Amp
1
3
4
4
Input Thru Sat 1 Sat 2 Sat 3 Sat 4
2
1
— Figure 2 —
TD-001556-01-A1
— Figure 3 —
2
Loading...