Qmark PowerCat User Manual
READ AND SAVE THESE INSTRUCTIONS.
®
SPECIFICATIONS
Input Motor Lamp Outlet Blower
THE POWER CAT
Model A300
115-120 2.0 Amps 40 Watt 120 Volts 300 CFM
Volts High 8.0 Amps
Intensity 960 Watts
S-11 Max.
Operation & Maintenance Instructions
!
WARNING
WARNING: To prevent the risk of electrical shock, fire, or injury to personnel, unplug from power supply before servicing,
cleaning, relamping, or oiling motor. Grilles must be reinstalled if removed for any reason before operating unit. DO NOT
exhaust explosive or flammable air mixtures. DO NOT use this fan with any Solid-State speed control device.
GENERAL
The Power Cat
technicians and home craftsmen who must, at times, perform jobs in extremes of heat, with inadequate lighting, and without
auxiliary power. These areas may include, but are not limited to attics, basements, closets, crawl spaces, garages, and similar confined spaces.
The Power Cat
as well as a duplex receptacle which makes available up to 8.0 amps (@ 120 volts) of electrical current in the immediate
work area. Electrical tools such as drills, saws, soldering irons, etc., may be operated from the Power Cat
need for multiple extension cords.
TIPS ON USING
1. Adjust elevation of air flow by moving carrying handle forward or backward. Air direction can be changed from horizontal to
vertical flow in this manner.
2. The 25’ extension cord, when not in use, may be secured by wrapping around the blower and handle with the plug end
tucked into the wrap.
3. The lamp is accessible for replacement by removing (2) screws holding the lamp guard in place. The guard may be
reinstalled by aligning two studs with matching holes in panel and reinstalling screws. When replacing lamp, use only
same type as originally installed. (40 Watt High Intensity Type S-11)
OVER-CURRENT PROTECTION:
The Power Cat
the branch circuit. All accessories that are to be plugged into the receptacle must not exceed a total current of 8 amps or the
built-in circuit breaker will trip. TO RESET, turn off unit, unplug accessory from Power Cat
DO’S & DON’TS
Do handle the Power Cat
Do keep clean. Blowing out the motor, blower housing, and impeller occasionally with compressed air will prolong the life and
permit more efficient air delivery. Keeping the lamp and reflector free of dust and dirt will also result in better light coverage.
Don’t overload the electrical outlet. Loads plugged into the outlet should not exceed 8.0 amps.
Don’t use the Power Cat
®
has been designed and constructed with maximum consideration for the needs of electricians, plumbers,
®
with its 25’ heavy duty cord furnishes a cooling flow of air, adjustable to the specific work area, a flood light,
®
, eliminating the
®
is provided with a built-in duplex receptacle which is protected with a circuit breaker to prevent overloading
®
outlet, and push RESET button.
®
as you would any other fine electrical power tool.
®
in wet locations.
REF REF
NO. DESCRIPTION QTY NO. DESCRIPTION QTY
1+Blower Housing 1 15 + Venturi, Motor Side 1
2+Strike 2 16 Motor 1
3*Screw, 8-18 x .375 4 17 * Screw, 8-18 x .375 6
4+Venturi, Inlet Side 1 18 Bumper, Rubber 4
5+Ring, “O” 2 19 * Screw, 8-18 x .375 4
6+Impeller 1 20 + Strain Relief 1
7 Switch, SPST, Lamp 1 21 * Screw, 6-20 x .375 3
7A Switch, SPST, Motor 1 22 + Plate, Bottom 1
8*Circuit Breaker 1 23 * Screw, 6-20 x .375 2
10 * Strap, Cable 1 24 * Screw, 6-20 x .313 2
11 + Receptacle, Duplex 1 25 + Guard, Lamp 1
12 + Clip, Speed 2 26 + Frame 1
13 + Grommet, Strain Relief 1 27 * Bulb, 40W, Intermed. Base 1
14 + Extension Cord 1 28 † Instruction Sheet 1
LIMITED WARRANTY
Dear Customer,
Thank you for your interest in Marley Engineered Products ventilator. We’re sure you will
enjoyitsbenefitsformany yearstocome. Pleasetake a minutetofill outthefollowinginformation and keep it in your permanent records.
Date Purchased Date Installed
Model Number Serial Number
This Marley Engineered Products ventilator is warranted to be free of defects in material and
workmanship for 12 months from date of original purchase.
There is no other warranty, express or implied, except such as is expressly set forth herein.
Sellerwillnotbeliableforanygeneral,consequential,orincidentaldamages, includingwithout
limitationany damagesfor loss of use or loss of profits, for any breachof warrantyor for negligence. Seller’s liability and buyer’s exclusive remedy are limited to the repair of defective
goods or the shipment of equivalent goods, or the granting of a reasonable allowance on
account of any defects,as the seller may elect.
To obtain performanceunder this warranty, you must:
1. Contact the MarleyEngineered ProductsService Department at 1-800-642-HEAT between
the hours of 8:00 a.m. and 5:00 p.m. E.S.T. Mondaythrough Friday.
2. Provide the model number of the product, the date of installation, and state the nature of
the difficultybeing experienced.
LIMITEDWARRANTY
3. The Marley Engineered Products ServiceRepresentativewilldetermine the best way to
resolve the difficulty.
Productswithin warranty whichhavebeeninstalled and returnedtotheseller for repair will
be repaired and returned as used products. Repairsto productsoutside the warranty period will be subject to labor and parts charges.
Some states have enacted legislation which (a) does not allow the inclusion of limitations
on incidental or consequential damages; (b) does not allow limitations on the length of a
warranty period; (c) precludes exclusion, during the period of a limited warranty, of any
implied warranties of merchantability or fitness for purpose.
To the extent of such provisions being applicable in your state, the limitations in this warranty may not apply.
TO ENSURESAFEOPERATION
• Be sure that this unit is correctly installed and wired by a qualifiedinstaller in accordance
with the instructions and applicable NEC or equivalentcodes.
• Be sure that operating instructions are followed and that moving and heatingpartsare
kept clean and free from obstructions.
Any warranties granted or liabilities assumed hereunder will not apply to goods that have
been damaged in transit, altered, repaired, installed or operated otherwise than in conformity with the above requirements for safe operation.
HOW TO OBTAIN WARRANTY SERVICE AND
WARRANTY PARTS PLUS GENERAL INFORMATION
1. Warranty Service or Parts 1-800-642-4328
2. Purchase Replacement Parts 1-800-654-3545
3. General Product Information www.marleymep.com
Note: When obtaining service always have the following:
1. Model number of the product
2. Date of manufacture
3. Part number or description
Part No. 5200-2616-001
ECR 37573
01/08
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA
Loading...