Qasair FA 60F-1, FA 90F-1, FA 90F-2, MT 60L-1, MT 90L-1 Installation Instructions Manual

VENTILATION SYSTEMS

INSTALLATION INSTRUCTIONS

QASAIR Rangehoods are made to suit

domestic Australian cooking conditions and

traditions. QASAIR incorporates a system

that is efficient over all modern-cooking

appliances, while achieving unequalled level

of quietness in the kitchen.

Now the latest domestic cooking appliances

including indoor barbecues, deep fryers,

exotic wok appliances and high speed gas

burners can be used in the design of the

kitchen without the worry or fear of filling the

house with grease, odours, steam or heat.

QASAIR Installation Instructions

1

Important information 2
Instructions for Models 4
FA / MT / MC / UCH / UV / NDCH / ECH
Instructions for Models 13
H Series & PYR
Instructions for Models 17
3F / SF / ST / MAJ / IN / STA / SMF / FAS
Instructions for Models 23
TR CT
Instructions for Models 25
BRH / BAR
Instructions for Models 27
4F / VIS / PRE / D 400 / D 500 / SQ 420 / FPR / MA /HAM / BUR
Instructions for Special Rangehoods 35

Lamp Replacement 36
Ducting Pieces 37
Installation Ideas 50
Exclusions 55
Warranty

CONTENTS

QASAIR Installation Instructions

2

CONDARI PTY LTD makes over 120 different models of QASAIR Rangehoods plus
many specials designed by architects and interior designers.

It is important to follow the installation instructions for different models.

The following is general advice for the installation of QASAIR Rangehoods and is meant as a guide.

Firstly, there are many different cooking appliances on the market today and we list some here.
Electric Eco, Ceramic hotplates, Teppanyaki plates and Induction hotplates, which need special cooking
equipment. There are gas hotplates with four burners and a wok burner or fish burner of all different heat
output. Many companies offer a vario system with individual two gas burners, a wok burner, electric
ceramic hotplate, an electric griller or barbecue and an induction hotplate. There are three gas cooking
appliances with an open flame griller or barbecue.

Gas regulations require different heights for different brands of hoods. QASAIR hoods can be fitted 600
mm above the trivet of a gas hotplate. This is due to the fact they do not have plastic motors or plastic
internal parts. Over the open flame gas grillers or gas barbecues the filters must be 1200 mm above the
cooking surface. Therefore, a special rangehood is required to comply with the regulations. There are no
regulations over an electric hotplate except for those set out by the manufacturer.

All decorative hoods in the Sapphire, Gallery, Imperial, Argyle, Federation and Heritage range should be
set from 700 mm to 800 mm above the cooking surface. When the rangehoods are against a wall in a
galley or partially enclosed kitchen, they can be higher, but should not exceed 900 mm to 1000 mm.

For island situations they should not exceed 800 mm above as movement around the bench will result in
fumes being drawn away from the catchment area of the hood.

We have a model, the Thermidor which is installed in the ceiling and is higher than the recommendation.
This is for aesthetic reasons such as a view or window setting. The hood is fitted with three fans to
provide the necessary air movement.

The Executive Range of hoods are all meant to be put into cupboards over hotplates and can vary in
height due to the kitchen design. All of these hoods can be 600 mm above a gas and electric hotplate.
Above a gas wok burner or electric griller or barbecue they should be 700 mm to 800 mm above.
Over an induction cooktop the minimum distance should be 700 mm above, this applies to the Marcel
(MC1000L-2), all Undermounted (NDCH), Mini Trim (MT 60/90L-1) and all Undercupboard (UCH) models.

1. The installation of QASAIR Rangehoods must comply with the information in

this booklet QASAIR Rangehoods are designed and made to work efficiently
over all domestic cookware available on the Australian market.

2. Every QASAIR Rangehood must be ducted to the outside atmosphere by the

use of zinc-alume duct or non-porous and non-flammable materials. We do not
recommend the use of any type of flexible ducting. Rangehoods must not be
vented into a wall cavity or a ceiling space. This prevents a build up of grease,
which can be a fire risk. Ensure the external outlet vent does not restrict the
airflow in any way, as this may result in reduced performance.

IMPORTANT

information

QASAIR Installation Instructions

3

3.

QASAIR Rangehoods must be ducted in duct work equivalent to the outlet

of the rangehood ie: The cross sectional area of the rangehood outlet and
the duct work must be equal. Do not reduce the duct size or have sharp
bends. Enlarge the duct size if the duct is to run 6 metres or longer. Advice
from QASAIR is available to ensure optimum performance. Always use non­flammable materials to minimise the risk of fire in the duct at a later date.

4. Ensure all ducting pieces are correctly fitted and sealed with either duct tape

or silicone to ensure that fumes do not escape into the ceiling space and seep
into living areas through vents or light fittings. The installation and fitting of the
rangehood should be done in such a way that will allow the unit to be removed
if service is required. Additional costs incurred in the removal of wall tiles,
damage to walls or bench tops are not covered by warranty.

5. Always adequately ventilate the room when the rangehood in use at the same

time as appliances burning gas or other fuels.

6. WARNING: Incorrect venting will result in additional noise and a reduction in

efficiency. Exhaust air must not be discharged into any chimney or flue, which
may carry combustible products from other sources.

A/ Do not discharge the air-flow from the rangehood into a flue used for

exhausting fumes from burning gas or fuel;

B/ For cleaning purposes please refer to page 36 of installation instructions for

stainless steel;

C/ If cleaning is not carried out in accordance with the instructions as listed on

page 36, you may have an increased risk of fire;

D/ Accessible parts of the rangehood may become hot when used with

cooking appliances;

E/ This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.

7. Do not flambé under the rangehood.

8. If the supply cord is damaged, an authorised service centre or licensed

electrician must replace it.

9. NOTE: QASAIR recommend an air movement of between 1000 to 1400 cubic

metres per hour over an indoor barbecue, depending on the length of the duct
run. Ensure a twin motor unit is installed over indoor barbecues for optimum
results. Barbecues should be positioned under the centre of the hood where the
fans are mounted and not near the outer edges where leakage may occur.

10. The lights in the canopy rangehoods are LED and come with a night light and

the concealed units come with compact fluorescent lights and these should be
turned off after use.

11. To reduce the risk of fixing screws coming in contact with live parts, do not

drill or screw into the rangehood. Live wires are encapsulated where possible
to prevent user contact. If necessary drill from the inside out and only through
single sheet material.

12. QASAIR domestic rangehoods are not to be used over barbecues approved

for outdoor use only.

13. QASAIR make a range of hoods specifically for outdoor barbecues in alfresco

areas under the CONDOR name.

14. QASAIR can manufacture rangehoods to be used over commercial cookers in

domestic applications.

QASAIR Installation Instructions

4

Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations. Connection to be carried
out by a registered electrician.

Duct direction (For all models except MT)

Before installing your rangehood check whether it has the fan mounted for back or top ducting.
For top ducting, the fan must be fixed to the back of the unit with the air outlet at the top, and for back
ducting, the fan must be fixed to the top of the unit with the air outlet at the back.
To change from top to back or back to top, proceed as follows:

Duct direction for UCH models

The motor shown is fitted to the back plate (P) and this plate is attached to the hood by screws (S). To
change from top to back undo all the screw (S), 14 of them and remove the plate and turn it around so the
motor points out the way required. Fit all the screws again and tighten.

Duct direction for UV / FA models

The photo's show a UV rear ducted and a FA top ducted unit. To change the direction undo the motor bolts
(B) on both sides of the motor. The motor can then be changed to point in the direction required. Replace
the bolts and tighten.

INSTRUCTIONS

for models

FA 60F-1

FA 90F-1

FA 90F-2

MT 60L-1

MT 90L-1

MC 10L-2

UCH 50F-1

UCH 80H-1

UCH 80H-2

UCH 100H-2

UCH 120H-2

UV 500F-1

UV 800F-1

UV 800F-2

UV 1000F-2

UV 1200F-2

UV 1200F-3

UV 1500F-3

NDCH 60F-1

NDCH 80F-1

NDCH 80F-2

NDCH 90F-1

NDCH 90F-2

NDCH 100F-2

NDCH 120F-2

ECH 600F-1

ECH 800F-1

ECH 800F-2

ECH 900F-1

ECH 900F-2

ECH 1000F-2

ECH 1200F-2

QASAIR Installation Instructions

5

Installation instructions Fold Away model (FA)

1. The rangehood can now be installed by inserting screws in the three holes provided on each side or

to the top or back by drilling your own mounting holes as required.

2. When installed, cover the access holes to the side fixing screws with the plastic plugs supplied.

3. Fit filters.

Duct direction for MT model only

To change the duct direction, proceed as follows:

1. Remove the screws from the fan access panel and remove access panel.

2. Unscrew the 2 x 700 hex head screws fixing the fan to the hood.

3. Rotate the fan assembly so that the air outlet meets with the rangehood outlet hole through which

you are going to vent (top or back).

4. Replace the 2 x 7mm screws.

5. Refit the fan access panel.

Installation instructions Mini Trim model & Marcel (MT & MC)

1. Fit a shelf at 410mm from the base of the cupboard.

2. Note hinge location prior to drilling.

3. Work from the centre line mark and drill 4 x M5 to M8 holes.

4. For top ducted models, cut out hole for the ducting allow 20mm clearance.

5. Fix left and right hand mounting brackets (supplied) 145mm from the base of the cupboard flush with

the rear of the unit. Notch to the back.

6. Lift rangehood onto mounting brackets by holding either end. DO NOT use the slide mechanism as

this may cause damage.

7. Insert the 4 x 50mm pan head screws supplied through the shelf and into the rangehood. Turn

clockwise to level the rangehood.

8. Fix the rangehood position by inserting 2 x no 8 1/2 inch screws through the left and right hand brackets.

9. Fit doors.

10. Minor adjustments may be required on the rangehood handle. Loosen the screws on the rear of the

handle and adjust handle position and re- tighten. The rangehood handle can be replaced.

11. All of the rangehoods shown on pages 1 and 8 are supplied with a 10AMP plug and lead for

connection to a 10AMP GPO, which must be in an accessible position.

12. The handle can be removed and replaced with one made by the cabinet maker to fit in with the

kitchen cabinets. The MT 90 has 3 screws and the MT 60 has 2 screws. These can be accessed by
sliding the facia out and un-screwing the front from underneath and behind the facia. The handle will
come off by tilting it forward from the top.

QASAIR Installation Instructions

6

Installation instructions

For Under cupboard and Universal model (UCH, UV, ECH & NDCH)
Make cut out to the following sizes.

MODEL HOOD SIZE BASE SIZE CUT OUT DIMENSION

UCH 50F 243 x 480 280 x 500 260 x 485

UCH 80H 243 x 780 280 x 800 260 x 785

UCH 100H 243 x 980 280 x 1000 260 x 985

UCH 120H 243 x 1180 280 x 1200 260 x 1185

UV 500F 390 x 480 430 x 500 398 x 485

UV 800F 390 x 780 430 x 800 398 x 785

UV 1000F 390 x 980 430 x 1000 398 x 985

UV 1200F 390 x 1180 430 x 1200 398 x 1185

UV 1500F 390 x 1480 430 x 1500 398 x 1485

NDCH 60F 243 x 580 280 x 600 260 x 585

NDCH 90F 243 x 880 280 x 900 260 x 885

NDCH 100F 243 x 980 280 x 1000 260 x 985

NDCH 120F 243 x 1180 280 x 1200 260 x 1185

ECH 600F 340 x 580 380 x 600 348 x 585

ECH 800F 340 x 780 380 x 800 348 x 785

ECH 900F 340 x 880 380 x 900 348 x 885

ECH 1000F 340 x 980 380 x 1000 348 x 985

ECH 1200F 340 x 1180 380 x 1200 348 x 1185

Loosen screws A and B by turning anti-clockwise.
Insert rangehood into cut out and turn screw ‘C’ clockwise to align rangehood with cupboard base.
Do not over tighten.
Tighten screw ‘A’ by turning clockwise to lock fixing bracket.
Fit off ductwork as required.
To remove rangehood, turn screw ‘D’ clockwise.

Models ECH

NDCH90
NDCH 100
NDCH 120

Models UCH

UV
NDCH60

QASAIR Installation Instructions

7

Executive Range - FOLDAWAY

FA 60F-1 Top / Back ducted
FA 90F-1 Top / Back ducted
FA 90F-2 Top / Back ducted

Executive Range - MINI TRIM

MT 60L-1 Top / Back ducted
MT 90L-1 Top / Back ducted

QASAIR Installation Instructions

8

Executive Range - MARCEL

MC 10L-2 Top / Back ducted

Executive Range - UNDERCUPBOARD

UCH 50F-1 Top / Back ducted
UCH 80H-1 Top / Back ducted
UCH 80H-2 Top / Back ducted
UCH 100H-2 Top / Back ducted
UCH 120H-2 Top / Back ducted

A WORD OF WARNING FOR THE UCH
MODELS OVER INDUCTION COOKTOPS.
If using this hood and boiling for long
periods of time (15 minutes plus)
condensation will form on the filters.
Using high speed will cause water to
drop back on to the hot plate. In all cases
use low speed and only one motor even if
the hood has two.
It is better to use a Universal rangehood,
as it has a larger filter area.

QASAIR Installation Instructions

9

Executive Range - UNIVERSAL

UV 500F-1 Top / Back ducted
UV 800F-1 Top / Back ducted
UV 800F-2 Top / Back ducted
UV 1000F-2 Top / Back ducted
UV 1200F-2 Top / Back ducted
UV 1200F-3 Top / Back ducted
UV 1500F-3 Top / Back ducted

Executive Range - UNDERMOUNTED

NDCH 60F-1 Top / Back ducted

QASAIR Installation Instructions

10

Executive Range - UNDERMOUNTED

NDCH 80F-1 Top / Back ducted
NDCH 80F-2 Top / Back ducted

Executive Range - UNDERMOUNTED

NDCH 90F-1 Top / Back ducted
NDCH 90F-2 Top / Back ducted
NDCH 120F-2 Top / Back ducted

QASAIR Installation Instructions

11

Executive Range - UNDERMOUNTED

NDCH 100F-2 Top / Back ducted

QASAIR Installation Instructions

12

Elite Range - ECH

ECH 600F-1 Top / Back ducted
ECH 800F-1 Top / Back ducted
ECH 900F-1 Top / Back ducted

Elite Range - ECH

ECH 800F-2 Top / Back ducted
ECH 900F-2 Top / Back ducted
ECH 1000F-2 Top / Back ducted
ECH 1200F-2 Top / Back ducted

QASAIR Installation Instructions

13

Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.

Electrical: Wiring to the appliance must comply with State and local Regulations. Connection must be
carried out by a registered electrician.

Recommended fixing points

Mounting bracket: Use vertically punched slot for centre line
Before cutting any holes check ceiling space for structural beams. It may be possible at this point to
relocate the hood position.

The fixing points are prepunched holes in the back of the hood and it may be necessary to drill through the
back of the hood into the wall studs.

Cleaning of Stainless Steel

QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.

This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes stainless
by the chromium oxidising in the open air to form a protective coating of chromium oxide. This coating
can be upset by coming in contact with a substance that will attack the chromium oxide, such as a
lemon solution or any cleaner with a preservative in it.

Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or warm
soapy water with soap will do it. Do not use powder detergent.

INSTRUCTIONS

for models

600HL-1

700HL-1

900HL-1

1200HL-2

1500HL-2

PYR 900L-1

QASAIR Installation Instructions

14

Installation instructions

1. Remove canopy and flue from boxes and check you have correct model and flue.

2. Locate centre point of stove.

3. Use level or plumb line to mark centre up to ceiling.

4. Mark level line for base of canopy 700-800mm above bench 750mm desirable.

5. Check roof space above for wires and obstructions as now is the time to decide on any changes to

location due to immovable obstructions.

6. Mark flue size on ceiling and cut neat exact hole to pass flue through.

7. For rear ducted models cut hole in wall for vent to pass through.

8. Fix mounting bracket to wall at desired height.

9. Remove fan(s) from canopy by removing side fixing bolts and disconnecting electrical plug at flexible

connector.

10. Locate solid fixing points on wall and drill holes in rear of canopy to suit. If no solid fixing is available

then now is the time to install fixing points. Four points are recommended with one on each side at
top and one on each side at bottom.

11. Drill hole in rear of unit to pass power connection through where available on wall.

12. Check flue slides through hole in ceiling.

13. Place canopy flat on floor and fit stainless flue over spigot pushing all the way down for a neat fit.

Drill hole in rear of flue and fix to canopy with pop rivet or screw.

14. Carefully lift canopy into position, guiding flue through ceiling and feeding power cable through hole

in rear of canopy. Make sure canopy is sitting correctly on mounting bracket then fix to wall through
fixing holes with solid screws. (You may need to place a packer behind canopy if wall is bowed to
make the canopy sit correctly).

15. Complete electrical connection to 10 AMP junction box to local electrical authority regulations

ensuring power is turned off during work.

16. Fit ducting to outside or exterior wall vent for rear ducted models. (Seal rear vents onto rear of hood

with silicone). A plumber should seal roof penetration with appropriate flashing. All joins in ducting
need to be sealed with duct tape or silicone and only use approved ducting of the correct size for
your canopy.

17. Fit motor(s) back into canopy with fixing bolts and plug electrical connector in.

18. Test run hood.

QASAIR Installation Instructions

15

Heritage Range – H

600HL-1 Top / Back ducted
700HL-1 Top / Back ducted
900HL-1 Top / Back ducted

• Duct outlet dimension
top ducted 240 x 106mm
back duct 235 x 110mm

• Standard single motor ducting will fit

It is recommended that the hood be
positioned 700 to 800 above the cooktop.
QASAIR suggests 750 and the DLE flues
supplied are either 600/900/1200 or 1500
long. Please ensure you have the correct
flue before installing the hood.

Heritage Range – H

1200HL-2 Top / Back ducted
1500HL-2 Top / Back ducted

• Duct outlet dimension
top ducted 370 x 150mm
back duct 235 x 110mm

• Standard 2 motor ducting will fit

It is recommended that the hood be
positioned 700 to 800 above the cooktop.
QASAIR suggests 750 and the DLE flues
supplied are either 600/900/1200 or 1500
long. Please ensure you have the correct
flue before installing the hood.

QASAIR Installation Instructions

16

Heritage Range – PYRAMID

PYR 900L Top / Back ducted

• Duct outlet dimension 235 x 110mm

• Standard single motor ducting will fit

QASAIR Installation Instructions

17

Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations. Connection to be carried
out by a registered electrician.

Flue fitting instructions 3 Flare Models Only

1. Check that the flue is the correct length prior to fitting.

2. Peel back PVC on the flue.

3. Place the rangehood on a level surface.

4. Remove the phillips head transit screws from the top of the rangehood.

5. Position the flue over the outlet and place all the rivets in the holes available and then fasten them.

6. Fit the flue back plate.

Installation instructions

1. Prepare wall by marking level line at desired height above cooktop.

2. Plumb line from centre of cooktop to ceiling and mark flue cut out. Position mounting bracket on wall

and fix with four screws. Mounting bracket is not necessary when installing over a splashback.

Note: The fixing bracket is 32mm shorter than the rangehood and should be located from the centre

only.

3. Cut a neat hole through the ceiling and remove any obstructing timbers.

Note: Various offsets are available from your QASAIR dealer to duct around any major structural

beams which cannot be removed. Ask your QASAIR dealer for advice.

4. In the case of back ducted models, cut a hole in the wall at the desired height.

5. Locate solid fixing point in wall to support hood. If there is no solid fixing point it will have to be

placed in the wall before proceeding. QASAIR recommend at least four (4) fixing points.

6. Drill holes in back of unit at suitable fixing points.

7. Drill 20mm hole in the rear of unit for 240 volt power cable as close as possible to junction box or

use hole below the junction box.

8. Place flue over spigot of hood then carefully lift into position on level line. Ensure flue is pushed into

position and electrical cable is fed into rear of unit.

9. Duct in approved manner to outside atmosphere.

Cleaning of Stainless Steel

QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.

This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes stainless
by the chromium oxidising in the open air to form a protective coating of chromium oxide. This coating
can be upset by coming in contact with a substance that will attack the chromium oxide, such as a
lemon solution or any cleaner with a preservative in it.

Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or warm
soapy water with soap will do it. Do not use powder detergent.

INSTRUCTIONS

for models

3F 900L-2

3F 1200L-2

3F1200L-3

3F 1500L-3

SF 900L-1

SF 900L-2

SF 1200L-2

ST 900L-1

ST 900L-2

ST 1200L-2

MAJ 900L-1

MAJ 900L-2

MAJ 1000L-2

MAJ 1200L-2

MAJ 1500L-2

IN 600L-1

IN 900L-2

IN 1200L-2

IN 1200L-3

STA 900L-2

STAR 900L-2

STA 1200L-2

STAR 1200L-2

SMF 600L-1

SMF 900L-1

SMF 900L-2

SMF 1000L-2

SMF 1200L-2

SMF 1500L-2

SMF 1500L-3

SMF 1800L-3

FAS 900L-2

FAS 1200L-2

QASAIR Installation Instructions

18

Federation Range – 3 FLARE

3F 900L-2 Top / Back ducted
3F 1200L-2 Top / Back ducted

• Duct outlet dimensions:
top ducted 300 x 180 and 400 x 180
back duct 250 x 250

• Standard 2 motor ducting will fit

• A transition piece is supplied to fit to the
top of flue to suit 2 motor ducting

3F 1200L-3 Top / Back ducted
3F 1500L-3 Top / Back ducted

• Duct outlet dimensions:
top ducted 400 x 200
back duct 110 x 235 and 250 x 250

• Standard 1 motor and 2 motor ducting
will fit

Federation Range – SINGLE FLARE

SF 900L-1 Top / Back Ducted

• Duct outlet dimension 240 x 110

• Standard single motor ducting will fit

• Top ducted model is supplied with a DLE
S/S Flue

SF 900L-2 Top / Back Ducted
SF 1200L-2 Top / Back Ducted

• Duct outlet dimensions:
top ducted 370 x 150
back ducted 250 x 250

• Standard 2 motor ducting will fit

• Top model is supplied with a DLE-2 S/S
Flue

QASAIR Installation Instructions

19

Federation Range – STEP

ST 900L-1 Top / Back Ducted

• Duct outlet dimension 235 x 110

• Standard single motor ducting will fit

• Top ducting model can have a DL-1 drop
into the motor

ST 900L-2 Top / Back Ducted
ST 1200L-2 Top / Back Ducted

• Duct outlet dimensions:
top duct 370 x 150
back duct 250 x 250

• Standard 2 motor ducting will fit

Imperial Range – MAJESTIC

MAJ 900L-1 Top / Back Ducted

• Duct outlet dimension 235 x 110mm

* For hoods shorter than 750mm high

this dimension varies to a minimum of
440mm

MAJ 900L-2 Top / Back Ducted
MAJ 1000L-2 Top / Back Ducted
MAJ 1200L-2 Top / Back Ducted
MAJ 1500L-2 Top / Back Ducted

• Duct outlet dimension 250 square

* For hoods shorter than 750mm high

this dimension varies to a minimum of
300mm

QASAIR Installation Instructions

20

Gallery Range – INTEGRA

IN 600L-1 Top / Back Ducted
IN 900L-2 Top / Back Ducted
IN 1200L-3 Top / Back Ducted

• Duct outlet dimension 235 x 110mm

• Standard single, twin or triple motor
ducting will fit

Gallery Range – STATESMAN

STA 900L-2 Top / Back Ducted
STAR 900L-2 Top / Back Ducted
STA 1200L-2 Top / Back Ducted
STAR 1200L-2 Top / Back Ducted

• R – with rail

• Duct outlet dimension 250 square

• Standard twin motor ducting will fit

QASAIR Installation Instructions

21

Federation Range – MAITLAND

SMF 600L-1 Top / Back Ducted
SMF 900L-1 Top / Back Ducted
SMF 900L-2 Top / Back Ducted
SMF 1000L-2 Top / Back Ducted

• Duct outlet dimension 235 x 110

• Standard single motor ducting will fit

Federation Range – MAITLAND

SMF 1200L-2 Top / Back Ducted
SMF 1500L-2 Top / Back Ducted
SMF 1500L-3 Top / Back Ducted
SMF 1800L-3 Top / Back Ducted

• Duct outlet dimension 235 x 110

• Standard single motor ducting will fit

QASAIR Installation Instructions

22

Shroud

The dimensions are shown on the diagram.
It is necessary to measure the height to the
ceiling on each side of the motor box so we get

the exact measurement to make the shroud.

We will leave a 2mm gap to allow for any

variation in the ceiling or hood installation.

Imperial Range – FASANO

FAS 900L-2 Top Ducted
FAS 1200L-2 Top Ducted

• Duct outlet dimension 250 square

• Standard twin motor ducting will fit

QASAIR Installation Instructions

23

The Thermidor rangehood is designed to be built into the ceiling.

Installation instructions

1. Remove hood from packaging being careful not to touch the stainless steel front.

2. Locate centre of stove and using level or plumb line, mark centre line up to the ceiling.

3. In a new house the hood can be fixed into the ceiling space by bolting or screwing into the ceiling

joists or by building a frame to support the hood.

4. In an existing home, a hole must be cut into the ceiling and pushing the hood into the space. Ensure

there are no obstructions to placing the hood in position. In these cases a ceiling flange in stainless
can be supplied to finish the hood to the ceiling. It is not supplied in colours.

5. The outlets are either top or back ducted and can be changed on site and the hood can be reversed

to suit the intended ducting direction.

6. Once secure in position standard ducting pieces can be used.

7. Switches are not provided and remote switching in a convenient position must be installed. The

switching used must be an electrically approved switch and is not provided by
Condari Pty Ltd.

INSTRUCTIONS

for models

TR CT 1000-3

TR CT 1200-3

TR CT 1500-3

TR CT FLANGE 1000

TR CT FLANGE 1200

TR CT FLANGE 1500

QASAIR Installation Instructions

24

Gallery Range – THERMIDOR

TR CT 1000-3 Top / Back Ducted
TR CT 1200-3 Top / Back Ducted
TR CT 1500-3 Top / Back Ducted

• Duct outlet dimension 235 x 110mmw

• Standard triple motor ducting will fit

TR CT FLANGE 1000
TR CT FLANGE 1200
TR CT FLANGE 1500

QASAIR Installation Instructions

25

Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations. Connection to be
carried out by a registered electrician.

Installation instructions

1. Remove hood from packaging being careful not to touch stainless steel front.

2. Locate centre of stove and using level or plumb line, mark centre line up to ceiling.

3. Measure height of hood and mark same distance down from ceiling with level line.

4. Mark where ducting needs to be cut either on wall or ceiling, check for wires and timber, then

cut hole for ducting.

5. Locate solid fixing points on wall (This hood is very heavy and requires good solid fixing

points). If necessary fit some solid fixing timber to wall behind hood now.

6. Mark fixing points on rear of hood and drill fixing holes to take solid screws.

7. Drill hole in rear or top of the hood to take electrical cable.

8. It may be easier to remove fans for easier fixing and weight when installing.

9. If you do not have adjustable stands you can cut some temporary timber props to sit canopy

on when you lift into position, to hold it while you fit fixing screws.

10. You need two people to lift this canopy into position. * Do not attempt this on your own, as

you could cause yourself injury and damage the hood or stove. CAUTION: Do not under any
circumstances lift from the front of the hood or put any pressure on the front face as you will
damage the hood permanently.

11. Carefully lift hood into position and sit on stands to level hood, then screw hood into position

through fixing holes. Make sure you put fixing holes high up in the hood to stop it falling forward.

12. Fit ducting to hood to the outside atmosphere as required either through the roof with

appropriate flashing by a plumber or through the rear wall vent, which needs to be siliconed
to the rear of the hood. Always use approved ducting and seal all duct joins with duct tape or
silicone.

13. An electrician should make the electrical connection to the hood by connecting to the 10 AMP

junction box. Ensure power is turned off during this procedure.

14. Refit fans to hood, insert filters and test.

Handy hints: Sometimes it is easier to lift the hood with a person in the roof space pulling up on a

rope attached to a wooden block placed inside base of hood and a second person down the bottom
guiding the hood into position.

Cleaning of Stainless Steel

QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.

This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes
stainless by the chromium oxidising in the open air to form a protective coating of chromium oxide.
This coating can be upset by coming in contact with a substance that will attack the chromium
oxide, such as a lemon solution or any cleaner with a preservative in it.

Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or
warm soapy water with soap will do it. Do not use powder detergent.

INSTRUCTIONS

for models

BRH 600L-1

BRH 900L-1

BRH 900L-2

BRH 1000L-2

BRH 1200L-2

BAR 1800L-2

BAR 2400L-2

QASAIR Installation Instructions

26

Argyle Range – BENTON

BRH 600L-1 Top / Back Ducted
BRH 900L-1 Top / Back Ducted
BRH 900L-2 Top / Back Ducted
BRH 1000L-2 Top / Back Ducted
BRH 1200L-2 Top / Back Ducted

• Duct outlets dimensions:
single – duct 235 x 110mm
twin – duct 250 square

• Standard single motor ducting will fit or
250sq for twin motor

Gallery Range – BARCLAY

BAR 1800/9L-2 Top / Back Ducted
BAR 2400/9L-2 Top / Back Ducted
BAR 2400/10L-2 Top / Back Ducted
BAR 2400/12L-2 Top / Back Ducted

• Duct outlets dimensions:
single – duct 235 x 110mm
twin – duct 250 square

• Standard single motor ducting will fit or
250sq for twin motor

QASAIR Installation Instructions

27

Installation must be carried out by the procedure outlined. Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations. Connection to be carried
out by a registered electrician.

Installation instructions

It is recommended that the rangehood be mounted 100mm back from the edge of the benchtop.

1. The rangehood can be installed between 700mm and 800mm above the cooking surface. The

installer should check for local requirements in case additional provisions apply.

2. It is advisable to remove fans for easier handling of unit by removing retaining bolts or clips and

unplugging electrical connector.

3. Measure hole centres and duct size on top of the rangehood. This will vary with the hood size,

model and number of fans fitted and will determine the ducting required.

4. Using a plumb line, mark the ceiling before making the cut out. Check for obstructions like electrical

cables etc.

5. Cut two (2) supporting beams approximately 1.0m long and pre-drill hole centres so that the

supporting beams are 90 degrees to the ceiling joists.

6. Fit 8mm all thread (threaded rod) through holes provided and secure with nuts and washers.

7. Level unit by tensioning the 8mm nuts. Do not over tighten.

8. Fit off ducting as required.

Cleaning of Stainless Steel

QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.

This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes stainless
by the chromium oxidising in the open air to form a protective coating of chromium oxide. This coating
can be upset by coming in contact with a substance that will attack the chromium oxide, such as a
lemon solution or any cleaner with a preservative in it.

Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or warm
soapy water with soap will do it. Do not use powder detergent.

INSTRUCTIONS

for models

Island Rangehoods

4F 900L-2
4F 1200L-2
VIS 900L-2
VIS 1200L-2
VIS 1200L-3
VIS 1500L-3
PRE 900L-2
PRE 1200L-2
PRE 1500L-2
PRE 1500L-3
PRE 1800L-3
D 400-L1
D 500L-2
SQ 420-L2
FPRL-2
MA 2000-2500L-4
MA 2500-3000L-4
HAM 900L-2
HAM 1200L-2
BUR 900L-2
BUR 1000L-2
BUR 1200L-2
BUR 1200L-3
BUR 1500L-2
BUR 1500L-3

QASAIR Installation Instructions

28

Island hood fixing – for flat, cathedral and exposed beam roofs.

QASAIR Installation Instructions

29

Imperial Range – VISCOUNT

VIS 900L-2 Island Hood
VIS 1200L-2 Island Hood
VIS 1200L-3 Island Hood
VIS 1500L-3 Island Hood

• Duct outlet dimensions:
twin – duct 300 x 165mm
triple – duct 400 x 200mm

• Standard 3 motor ducting will fit

• Transition piece supplied with Hood to
DL-2 ducting

Federation Range – 4 FLARE

4F 900L-2 Island Hood
4F 1200L-2 Island Hood

• Duct outlet dimension 265 x 90mm and
300 x 90mm

• Standard 3 motor ducting will fit

QASAIR Installation Instructions

30

Imperial Range – PRESIDENT

PRE 900L-2 Island Hood
PRE 1200L-2 Island Hood

• Duct outlet dimension 250 x 250mm

• Standard 250 sq ducting will fit

Imperial Range – PRESIDENT

PRE 1500L-2 Island Hood
PRE 1500L-3 Island Hood
PRE 1800L-3 Island Hood

• Duct outlet dimension 250 x 250mm

• Standard 250 sq ducting will fit

QASAIR Installation Instructions

31

Argyle Range – ALBANY

D 400L-1 Island Hood

• Duct outlet dimension 110 x 235mm

• Standard DL-1 ducting will fit

Argyle Range – ALBANY

D 500L-2 Island Hood

• Duct outlet dimension 250 square

QASAIR Installation Instructions

32

Argyle Range – WINTON

SQ 420L-2 Island Hood

• Duct outlet dimension 250sq

• Standard 250mm ducting will fit

Argyle Range – BURDETT

BUR 900L-2 Island Hood
BUR 1000L-2 Island Hood
BUR 1200L-2 Island Hood
BUR 1200L-3 Island Hood
BUR 1500L-2 Island Hood
BUR 1500L-3 Island Hood

• Duct outlets dimensions:
twin – duct 250 square
triple – duct 200 x 400mm

• Standard single motor ducting will fit or
250sq for twin motor

QASAIR Installation Instructions

33

Gallery Range – MADDISON

MA 2000-2500L-4 Island Hood
MA 2500-3000L-4 Island Hood

• Duct outlet dimension 250sq

• Standard four motor ducting will fit or

Imperial Range – HAMILTON

BUR 900L-2 Island Hood
BUR 1200L-2 Island Hood

• Duct outlets dimension 250 square

• Standard single motor ducting will fit or
250sq for twin motor

QASAIR Installation Instructions

34

Argyle Range – FREMONT

FPRL-2 Island Hood

• Duct outlet dimension 250sq

• Standard 250mm ducting will fit

QASAIR Installation Instructions

35

Special Rangehoods are hoods made to specific designs and not covered by the instructions in this booklet
for standard hoods, although the basic rules will still apply.

Generally, special rangehoods are either wall or ceiling mounted and therefore are installed in the same
manner as the rangehoods in the previous pages.

Standard ducting will apply unless special ducting is supplied with the hood.

If any doubt arises, please ring your local agent or Melbourne office on [phone] or
1300 360 563.

Cleaning of Stainless Steel

QASAIR Rangehoods are made from stainless steel type 304 and is considered 18/8 SS.

This means the stainless steel is 18% chromium and 8% nickel in the mix. The steel becomes stainless
by the chromium oxidising in the open air to form a protective coating of chromium oxide. This coating
can be upset by coming in contact with a substance that will attack the chromium oxide, such as a
lemon solution or any cleaner with a preservative in it.

Therefore, only clean the rangehood with an approved stainless steel cleaner. Methylated spirits or warm
soapy water with soap will do it. Do not use powder detergent.

INSTRUCTIONS

for models

Special Rangehoods

QASAIR Installation Instructions

36

LAMP

replacement

and

FILTER care

QASAIR rangehoods are fitted with low voltage halogen lights which give a very clear, bright light. These
become very hot if left on for a long period and can burn out. Please switch off after use.

1. Turn off power at power point.
2 Turn retaining ring anticlockwise and pull down.

3. Tilt lamp up slightly at retaining spring opening position and slide lamp out sideways.

4. Unplug lamp from the ceramic connector and replace lamp.

5. If retaining ring will not rotate, dislodge lamp by gently pushing upwards to obtain a

better grip.

ROTATE ANTI CLOCKWISE TO REMOVE

Filters

For the best results, please clean filters regularly, you can do this by hand washing or placing in the
dishwasher. Try not to use any citrus or costic products as this can cause corrosion.

QASAIR Installation Instructions

37

101. DL-1 Duct Length 1200mm
DL-1C Duct Length (coloured)

103. HB-1-45 Horizontal Bend 45º

102. HB-1 Horizontal Bend 90º

104. BD/WV-H-1 Back Draft Wall Vent Horizontal

DUCTING

pieces

Single Motor

Twin Motor

Triple Motor

The following pages show all the ducting pieces available. They are made in zinc-alume and are non­flammable. We recommend that QASAIR rangehoods are ducted to the outside atmosphere by these duct
pieces. QASAIR will make special duct pieces on request if circumstances prevent the use of standard
pieces.

‹‹ Single Motor

101. DL-1E Duct Length Extenable 1200mm

101. DL-1A Duct Length 300mm

QASAIR Installation Instructions

38

105. BD/WV-H-1 MGS Back Draft Wall Vent
Horizontal Marine Grade Stainless Steel

108. BD/WV-V-1 Back Draft Wall Vent Vertical

111. TT-1 Twisted Transition

106. VB-1 Vertical Bend 90º

109. BD/WV-V-1 MGS Back Draft Wall Vent

Vertical Marine Grade Stainless Steel

112. DLE-DLE Flue Joiner

107. VB-1-45 Vertical Bend 45º

110. DD-1-L/R Duct Director Left or Right

113. CD-920 Cavity Duct Extendable

‹‹ Single Motor

114. CD-920 to DL-1 Duct to Duct Length 115. TR-1 Rectangular to Round Transition

116. DR-200 Duct Length 1200mm

QASAIR Installation Instructions

39

‹‹ Single Motor

117. DR-200 CB Duct Length 1200mm
Colourbond

120. BD-6/7/9-WV-R/R Rear Registar Kit

118. DR-200/45 Round Bend 45º

121. AS-20 Back Draft Shutter

119. DR-200/90 Round Bend 90º

122. CH-200 Chairman's Hat 200ø

123. CH-200 CB Chairman's Hat Colourbond

126. BD/SQ-RC 200 Back Draft Roof Cowl 200ø

124. BD/RC-1 Back Draft Roof Cowl

127. DLE-S/S CAP Stainless Steel Flue Cap

125. BD/RC-1 CB Back Draft Roof Cowl

Colourbond

128. BD/M-1 Back Draft Damper

QASAIR Installation Instructions

40

‹‹ Single Motor

132. WVC-V-1 Wall Vent Cover Vertical

135. EV/DL-1 Eave Vent Suit DL-1

138. HB-195/45 Horizontal Bend 45º

133. WVC-V-1 MGS Wall Vent Cover Vertical

Marine Grade Stainless Steel

136. DL-195 Duct Length

139. BD/WV-195SQ Back Draft Wall Vent

Square

134. 6/7/900H-SC Spigot Cap

137. HB-195 Horizontal Bend 90º

140. BD/RC-195SQ Back Draft Roof Cowl Sqaure

129. CF-6/7/900H Ceiling Flange 6/7/900H 130. WVC-H-1 Wall Vent Cover Horizontal 131. WVC-H-1 MGS Wall Vent Cover Horizontal

Marine Grade Stainless Steel

QASAIR Installation Instructions

41

‹‹ Single Motor

141. WVC-6/7/9H-R/R Wall Vent Cover

142. WVC-195SQ Wall Vent Cover

143. RCP-200 S/S Roof Cap 200ø

Stainless Steel

144. RC-200 S/S Roof Cowl 200ø
Stainless Steel

145. RC-200 Zinc Roof Cowl 200ø Zinc Alumne

146. RC-1 S/S Roof Cowl Single Motor

Stainless Steel

QASAIR Installation Instructions

42

201. TMT Twin Motor Transition

204. HB-2/45 Horizontal Bend 45º

207. VB-2 Vertical Bend 90º

202. DL-2 Duct Length 1200mm

205. BD/WV-H-2 Back Draft Wall Vent

208. VB-2/45 Vertical Bend 45º

203. HB-2 Horizontal Bend 90º

206. BD/WV-H-2 MGS Back Draft Wall Vent

Marine Grade Stainless Steel

209. BD/WV-V-2 Back Draft Wall Vent

‹‹ Twin Motor

210. BD/WV-V-2 MGS Back Draft Wall Vent
Marine Grade Stainless Steel

211. TT-2 Twisted Transition 212. DLE-2 to DLE-2 Flue Joiner

QASAIR Installation Instructions

43

‹‹ Twin Motor

213. BD10/12/15-WV-R/R Rear Register Kit

216. DR-300 Duct Length 300ø 1200mm

214. TMT-300 Transsition to 300ø

217. DR-300 CB Duct Length 300ø 1200mm

Colourbond

215. TR-2 Transition from DL-2 to 300ø

218. DR-300/45 Round Bend 45º

219. DR-300/90 Round Bend 90º

222. TMT-250 Twin Motor to 250sq

220. DL-2 /250SQ Rectangular to Square

Transition

223. DL-250 Duct Length 1200mm

221. TMT-250/300 Transition from 250sq

to 300º

224. HB-250 Horizontal Bend 90º

QASAIR Installation Instructions

44

225. HB-250/45 Horizontal Bend 45º

226. TMT-250/90 Duct Deflector 250sq

Left or Right

227. BD/WV-250SQ Back Draft Wall 250sq

‹‹ Twin Motor

228. BD/WV-250SQ MGS Back Draft Wall
250sq Marine Grade Stainless Steel

231. CH-300 Chairman's Hat 300º

234. BD/RC-250SQ Back Draft Roof Cowl 250sq

229. BD/RC-2 Back Draft Roof Cowl

232. CH-300 CB Chairman's Hat 300º Colourbond

235. DLE-2-S/S CAP Flue Cap

230. BD/RC-2 CB Back Draft Roof Cowl

Colourbond

233. BD/SQ-RC-300 Back Draft Roof Cowl 300ø

236. CF-10/12/1500H Ceiling Flange

10/12/1500H

QASAIR Installation Instructions

45

237. CF-3F900-2 Ceiling Flange 3F900-2

240. CF-4F1200-2 Ceiling Flange 4F1200-2

243. WVC-V-2 Wall Vent Cover Vertical

238. CF-3F1200-2 Ceiling Flange 3F1200-2

241. WVC-H-2 Wall Vent Cover Horizontal

244. WVC-V-2 MGS Wall Vent Cover Vertical

Marine Grade Stainless Steel

239. CF-4F900-2 Ceiling Flange 4F900-2

242. WVC-H-2 MGS Wall Vent Cover Horizontal

Marine Grade Stainless Steel

245. WVC-250SQ Wall Vent Cover 250sq

247. WVC10/12/15H-R/R Wall Vent Cover

10/12/1500H

248. 10/12/1500H-SC Spigot Cap

246. WVC-250SQ MGS Wall Vent Cover 250sq

Marine Grade Stainless Steel

‹‹ Twin Motor

QASAIR Installation Instructions

46

‹‹ Twin Motor

255. CF 3F-1500-2 Ceiling Flange 3F-1500-2

252. BD/M-250SQ Back Draft Damper 250sq

249. DD-2H-L/R Duct Director Horizontal

Left or Right

253. AS-25 Back Draft Shutter

250. DD-2V-L/R Duct Director Vertical

Left or Right

254. BD/WVC-SBS Back Draft Wall Vent Cover

251. EV/DL-2 Eave Vent to Suit DL-2

256. RCP-300 S/S Roof Cap 300ø

Stainless Steel

257. RV-300 S/S Roof Ventilation Cowl 300ø
Stainless Steel

258. RC-300 S/S Roof Cowl 300ø Stainless Steel 259. RC-2 S/S Roof Cowl Twin Motor

Stainless Steel

QASAIR Installation Instructions

47

306. VB-3/45 Vertical Bend 45º

309. TR-3 Transition to 350ø

308. TMT-400x200/350 Transition from DL-3

to 350ø

307. TT-3 Twisted Transition

304. HB-3/45 Horizontal Bend 45º

305. VB-3 Vertical Bend 90º

301. 3MT-DL-3 Three Motor Transition

302. DL-3 Duct Length 1200mm

303. HB-3 Horizontal Bend 90º

‹‹ Triple Motor

312. DR-350/45 Bend 45º 350ø

311. DR-350 CB Duct Length 350ø Colourbond

310. DR-350 Duct Length 350ø

QASAIR Installation Instructions

48

318. CH-350 Chairman's Hat 350ø

317. BD/SQ-RC350 MGS Back Draft Roof Cowl

350ø Marine Grade Stainless Steel

313. DR-350/90 Bend 90ø 350ø

314. BD/RC-3 Back Draft Roof Cowl

315.BD/RC-3 MGS Back Draft Roof Cowl

Marine Grade Stainless Steel

316. BD/SQ-RC350 Back Draft Roof Cowl 350ø

‹‹ Triple Motor

322. BD/WV-V-3 Back Draft Wall Vent Vertical

323. BD/WV-V-3 MGS Back Draft Wall Vent

Vertical Marine Grade Stainless Steel

324. WVC-H-3 Wall Vent Cover Horizontal

320. BD/WV-H-3 Back Draft Wall Vent

Horizontal

321. BD/WV-H-3 MGS Back Draft Wall Vent
Horizontal Marine Grade Stainless Steel

319. CH-350 CB Chairman's Hat 350ø
Colourbond

QASAIR Installation Instructions

49

327. WVC-V-3 MGS Wall Vent Cover Vertical
Marine Grade Stainless Steel

326. WVC-V-3 Wall Vent Cover Vertical

325. WVC-H-3 MGS Wall Vent Cover Horizontal

Marine Grade Stainless Steel

‹‹ Triple Motor

330. AS-35 Back Draft Shutter

329. DD-3V-R Duct Director Vertical Right328. DD-3V-L Duct Director Vertical Left

QASAIR Installation Instructions

50

1. FA 60-1B

2. FA 90-1T

INSTALLATION

ideas

3. FA 60-1T

QASAIR Installation Instructions

51

5. FA 60-1T

4. FA 60-1T

6. FA 60-1T / 60-1B

7. FA 90-2T

8. FA 90-2T 9. FA 90-2T

QASAIR Installation Instructions

52

12. FA 90-2T

11. FA 90-2T

14. 600H-T

13. 600H-T / 700H-T / 900H-T

15. UCH 50-1T

10. FA 90-2B

QASAIR Installation Instructions

53

16. UCH 80-1T

18. UCH 80-2T

17. UCH 50-1T

19. 1200H-T

20. UV 800-2T 21. UV 1000-2T

QASAIR Installation Instructions

54

22. 3F 900-2T / 1200 -2T

24. UV 800-1T

23. UV 500-1T

26. UV 1200-2B

25. UCH 80-1T / UV 1000-2T

QASAIR Installation Instructions

55

There are some exclusions from the Condari Pty Ltd Guarantee. The
Guarantee is printed at the back of brochure.

QASAIR Rangehoods are designed to be used over all domestic cookware
available in AUSTRALIA.

QASAIR Rangehoods are not to be used over barbecues approved for
outdoor use only.

Outdoor barbecues will have a rating plate on them specifying that they are
approved for outdoor use only and also a mega joule rating per burner or a
total mega joule rating.

In practice any barbecue or outdoor cooking appliance over 50 mega joule
will need a specially made rangehood with an air movement exceeding
2000 cubic meters per hour.

QASAIR have hoods to go over domestic cookers such as VIKING, WOLF
and CAPITAL cooking appliances. These brands have a mega joule rating
of up to 95 mj and therefore special hoods are required for the appliances.

QASAIR will manufacture special rangehoods to go over commercial
cooking appliances situated in domestic kitchens.

Once the heat output is over 50 mega joule a special rangehood is required.

QASAIR Installation Instructions

56

NOTES _____________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

_____________________________

QASAIR Installation Instructions

57

NOTES _____________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

_____________________________

QASAIR Installation Instructions

58

NOTES _____________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

__________________________________

_____________________________

STANDARD

WARRANTY

Condari P/L Appliance Guarantee

The benefits conferred by this warranty are in addition to all
other rights and remedies in respect of the product which the
consumer has under the Trade Practices Act and similar state
and territory laws.

Condari P/L in Melbourne (and by their agency in Country
Areas and other States) warrants that the appliance will be
free from defects in materials and workmanship for a period
of 36 months from the date of purchase of the appliance to the
consumer.

If there is a breach of this warranty, Condari will rectify, free
of charge, at it's nearest service centre or authorised service
agency any fault caused by faulty workmanship or material
at the time of manufacture occurring in the appliance within
36 months from the date of delivery of the appliance to the
customer.

This warranty is conditional upon the appliance being used only
for personal, domestic and household purposes and installed
and operated in accordance with QASAIR Instructions and does
not apply to articles which by their nature are consumable.

If a defect is caused by neglect, misuse, or failure to follow
operating instructions where special precautions are detailed
for user attention then a charge shall be made for the service call.

For example: With the filters the user is specifically requested:

To clean filter regularly by handwashing or placing in a
dishwasher at least once a month.

To turn off after each use.

Where a claim is made under warranty QASAIR reserves the
right to determine whether or not the fault is caused by faulty
workmanship or material or that the part is defective.

The consumer shall be fully responsible for all expenses
whatsoever incidental to the removal of parts from the unit or
to their replacement. Interalia, such responsibility shall extend
to damaged walls, tiles, fixtures and fittings whether or not
the unit has been built into a cupboard and irrespective of the
stage either of its installation or the fitting of any other item
whatsoever in its vicinity.

No other person, or firm or corporation is authorised by Condari
to offer or give on its behalf any other greater warranty that
given by Condari under this warranty.

Date installed ..................................

Purchased from ................................

Model ........................................

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serial No .....................................

The purchaser must fill in the above information and keep
this with the original purchase document. This form must be
produced if and when a claim is made under this warranty.

QASAIR Rangehoods are made in Ringwood, Australia.

Tel: [phone]

Fax: [phone]

QASAIR RANGEHOODS MADE IN RINGWOOD 3134

QASAIR RESERVES THE RIGHT TO CHANGE SPECIFICATION WITHOUT NOTICE. ® IS A REGISTERED TRADE MARK.

DISTRIBUTED IN AUSTRALIA BY CONDARI PTY LTD

Tel: [phone]
VIC Tel: [phone] Fax: [phone]
Email: [e-mail]
Website: www.qasair.com.au

YOUR DISTRIBUTORS

Australia

NSW Te l: [phone] Fax: [phone]
QLD Tel: [phone] Fax: [phone]
WA Te l : [phone] Fax: [phone]
SA Tel: [phone] Fax: [phone]
ACT Te l: [phone] Fax: [phone]
TAS Tel: [phone] Fax: [phone]
NT Tel: [phone] Fax: [phone]

New Zealand

Kitchen Appliance Specialist Ltd

320 Manchester Street

Christchurch New Zealand

Tel: [phone] Fax: [phone]

Kouzina Appliances

155 The Strand, Parnell

Auckland New Zealand

Tel: [phone] Fax: [phone]

Singapore

Eldric Marketing Pte Ltd

176 Orchard Road

#05-03 Centrepoint Singapore 238843

Tel: [phone] Fax: [phone]

5 Pereira Road

#02-01 Asiawide Industrial Building

Singapore 238843

Tel: [phone] Fax: [phone]

07/12

PRINTED IN MELBOURNE AUSTRALIA