Qasair BAL1000L3, BCM10003SS, BCM1000L3, BAL1200L3, BCM1200L3 Installation Guide
...
INSTALLATION
INSTRUCTIONS
Boston Rangehood
2
Condor Rangehood Installation Instructions
Important Information
4
Instructions for Models
BSF / BCM / C / BAL
Instructions for Models
DAR / FAL / ICU / CUB
Ducting Pieces
Cleaning
Guarantee & Exclusions
Warranty
6
12
18
20
21
23
Condor Rangehood Installation Instructions
3
IMPORTANT INFORMATION
CONDARI PTY LTD makes over 120 different models of QASAIR and CONDOR Rangehoods plus many
specials designed by architects and interior designers.
It is important to follow the installation instructions for different models.
The following is general advice for the installation of CONDOR Rangehoods and is meant as a guide.
Firstly, there are many different cooking appliances on the market today and we list some here.
Electric Eco, Ceramic hotplates, Teppanyaki plates and Induction hotplates, which need special cooking
equipment. There are gas hotplates with four burners and a wok burner or sh burner of all different heat output.
Many companies offer a vario system with individual two gas burners, a wok burner, electric ceramic hotplate, an
electric griller or barbecue and an induction hotplate. There are three gas cooking appliances with an open ame
griller or barbecue.
Gas regulations require different heights for different brands of hoods. CONDOR hoods can be tted between
1000 mm to 1400 mm above the barbecue. This is due to the fact they do not have plastic motors.
1. The installation of CONDOR Rangehoods must comply with the information in this booklet. CONDOR
Rangehoods are designed and made to work efciently over all domestic cookware available on the
Australian market.
2. Every CONDOR Rangehood must be ducted to the outside atmosphere by the use of zinc-alume duct or
non-porous and non-ammable materials. We do not recommend the use of any type of exible ducting
or plastic PVC piping (barbecue heat output will affect exible ducting and cause it to desintegrate).
Rangehoods must not be vented into a wall cavity or a ceiling space. This prevents a build up of grease,
which can be a re risk. Ensure the external outlet vent does not restrict the airow in any way, as this may
result in reduced performance.
3. CONDOR Rangehoods must be ducted in duct work equivalent to the outlet of the rangehood
ie: The cross sectional area of the rangehood outlet and the duct work must be equal. Do not reduce the
duct size or have sharp bends. Enlarge the duct size if the duct is to run 6 metres or longer. Advice from
CONDOR is available to ensure optimum performance. Always use nonammable materials to minimise the
risk of re in the duct at a later date.
4. Ensure all ducting pieces are correctly tted and sealed with either duct tape or silicone to ensure that fumes
do not escape into the ceiling space and seep into living areas through vents or light ttings. The installation
and tting of the rangehood should be done in such a way that will allow the unit to be removed if service is
required. Additional costs incurred in the removal of wall tiles, damage to walls or bench tops are not covered
by warranty.
5. Always adequately ventilate the room when the rangehood is in use at the same time as appliances burning
gas or other fuels.
6. WARNING: Incorrect venting will result in additional noise and a reduction in efciency. Exhaust air must not
4
Condor Rangehood Installation Instructions
be discharged into any chimney or ue, which may carry combustible products from other sources.
a) Do not discharge the air-ow from the rangehood into a ue used for exhausting fumes
from burning gas or fuel;
b) A reduction in ducting size will result in the motors eventually failing and will need replacement.
c) For cleaning purposes please refer to page 20 of installation instructions for stainless steel;
d) If cleaning is not carried out in accordance with the instructions as listed on page 20, you
may have an increased risk of re;
e) Accessible parts of the rangehood may become hot when used with cooking appliances;
f) This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
7. If the supply cord is damaged, an authorised service centre or licensed electrician must replace it.
8. NOTE: CONDOR recommend minimum air movement of 2000 cubic metres per hour and recomment up to
2700 cubic metres per hour over a barbecue, depending on the length of the duct run. Barbecues should be
positioned under the centre of the hood where the fans are mounted and not near the outer edges where
leakage may occur. Please also note barbecue lid position, as if it does not open to a 90 degree angle the
smoke and by-products can be diverted forward and away from the rangehood catchemt area.
9. The lights in the rangehoods are LED.
10. To reduce the risk of xing screws coming in contact with live parts, do not drill or screw into the rangehood.
Live wires are encapsulated where possible to prevent user contact. If necessary drill from the inside out and
only through single sheet material.
11. CONDARI PTY LTD can manufacture rangehoods to be used over commercial cookers in domestic
applications.
NOTE: Installation must comply with local State & Council regulations.
Condor Rangehood Installation Instructions
5
INSTALLATION INSTRUCTIONS
CONDOR WALL MOUNTED
g.
e perforated panel.
INSTALLATION INSTRUCTIONS CONDOR RANGE
To suit wall mounted models:
• Balmoral
• Boston
• Cubica
• Baltimore
1. Determine hood position on wall 1000mm to 1400mm above barbecue.
2. Unpack Rangehood.
3. Mark centre line on wall.
4. Mark base line on wall (Note: if shroud being used, the height of the shroud will determine
the height of the hood).
5. Mark the outlet hole in the ceiling for the ue and cut out, removing any obstructions
allowing clear access for the ue (Note: if using rear duct, mark and cut hole at this time).
6. Remove the perforated rear panel in hood by removing bolts with a 7mm hex socket.
7. Drill xing holes in rear of hood to suit available xing points on wall making sure to get
xing as high and as wide as possible in Rangehood to avoid sagging from wall. (Please
refer to Rangehood diagram for example of possible xing points)
8. Remove plastic cover from rear mounting plate and x to wall at base height of hood
making sure this is level and exactly central.
9. Transfer xing locations from hood to wall and drill xing holes. Insert plugs to allow or use
Dyna bolts as an alternative.
10. Locate position for power cable and drill hole for cable using a hole saw. Consult your
electrician for his preferred location.
Perforated
panels
7mm hex bolt head
6
Electrical
junction box
Condor Rangehood Installation Instructions
11. Fit stainless ue to top of hood with 4 supplied xing screws while hood is on ground to
avoid having to drop stainless ue down through hole in the ceiling and causing possible
damage to the ue. (If using shroud it can be tted either at this stage or carefully after
hood is on wall)
12. Remove fans if needed and lift hood up onto mounting bracket carefully guiding ue
through hole in ceiling and bringing power cable into hood during this process. You will
require up to 3 people for this lifting stage as hood is quite awkward and heavy to lift.
13. Screw or bolt hood to wall securely making sure hood is level and sitting properly on
mounting bracket. It is advisable to have portable stands ready for this stage as hood will
get quite heavy.
14. Ret perforated panel in the rear or the hood and ret fans if they have been removed.
15. Make electrical connection to junction box inside bottom right side of hood.
16. Extend ducting through roof to exterior and t roof cowl making sure to seal roof
penetration with preferred ashing material. (Note: there are several on the market to suit
the type of roof you have, so consult your plumber for the best product to suit)
Condor Rangehood Installation Instructions
7
LED Lights
Electrical connection is to be at the
junction box inside the rangehood.
All BSF rangehoods have 3 fans to
ensure all smoke from the barbecue
is removed from the alfresco area.
BSF
BALMORAL Specification Sheet
Top Ducted
Back Ducted
Wall Mounted
The flues available for BSF rangehoods
are model No DL-BC and come in lengths
of 600, 900, or 1200mm.
800
450
100
4
5
0
4
0
0
2
0
0
X
M
i
n
i
m
u
m
2
5
m
m
.
1
0
0
9
3
1
9
5
Power
Entry.
Top Ducted
Top Ducted
B
o
d
y
W
i
d
t
h
8
0
0
445
600
4
5
0
2
5
0
B
o
d
y
W
i
d
t
h
L
i
g
h
t
C
e
n
t
r
e
s
8
0
0
500
BALMORAL (BSF)
The ues available for BSF rangehoods are
model No DL-BC BSF and come in lengths of
600, 900 or 1200mm.
8
Condor Rangehood Installation Instructions
Loading...