Page 1
EN
www.Qacoustics.co.uk
Page 2
Page 3
Contents
04 Safety Information
05 Package Contents
06 Features
06 Feature Summary
06 Product Description
07 Instructions
07 Q-BT3 Features
11 Remote Control
12 Rubber Bumpers
13 Operating Q-BT3
17 Specication
18 Warranty
EC DECLARATION OF CONFORMITY
Q-BT3 conforms with the following EEC Directives their supporting Statutory Instruments and relevant Standards, where
applicable as follows:
EC Council Directive on electromagnetic compatibility 2004/108/EC,
Applicable standard(s) with amendments: EN5013:2001 + A1:2003 + A2:2006
EN55020:2007
EN61000-3-2:2006 + A1:2009 + A2:2009
EN61000-3-3:2008
EC Low Voltage Directive 2006/95/EEC,
Applicable standard(s) with amendments: EN60065:2002 + A1:2006 + A11:2008 + A2:2012
Stage 1 of annex II of Commission regulation (ErP) EC no. 1275/2008
Contents
3
Page 4
Safety Information
IMPORTANT INFORMATION - PLEASE READ CAREFULLY
Read and keep these instructions.
Heed all warnings and follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Warnings:
To avoid the danger of suocation, keep all polythene
bags and packaging away from babies and children.
To reduce the risk of re or electrical shock, do not expose
this product to rain or moisture. This product must not be
exposed to dripping and splashing and no object lled
with liquids such as a vase of owers should be placed
on the unit.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wider
blade or the third prong are provided for your safety. If
the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
Take note of all warnings on the appliance, under no
circumstances disassemble the unit or remove covers to
prevent the risk of re or electrical shock.
Protect the mains power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Use only attachments/accessories specied by the
manufacturer.
Unplug this unit during lightning storms or when unused
for long periods of time.
No naked ame sources such as candles should be
placed on the product.
Caution:
Changes or modications not expressly approved by the
manufacturer could void the user’s authority to operate
this device.
Third parties: In the unlikely event that you pass this
product on to a third party, include these operating
instructions with the product.
Service:
Refer all servicing to qualied service personnel.
Servicing is required when the unit has been damaged in
any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the
unit, the apparatus has been exposed to rain or moisture,
does not operate normally or has been dropped.
Equipment for servicing should be returned to the
supplying dealer, or to the service agent for your area.
The address of the main Service Agent for the UK is listed
at the back of this manual.
Important notice for UK users:
The UK mains lead is terminated with a UK approved
mains plug tted with a 3A fuse. If the fuse needs to be
replaced, an ASTA or BSI approved BS1362 fuse rated at
3A must be used.
Safety Information
4
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a
safety connection to electrical earth.
Correct disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent
possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmentally safe recycling.
Page 5
5
Package Contents
Thank you for purchasing Q Acoustics Q-BT3.
This manual is intended to take you through the setup and installation of Q-BT3 and will help provide a
trouble free setup and optimum performance from the product.
Please read the instructions, important safety information and warnings carefully before installation, and
use, to ensure the safe and satisfactory operation of this product.
We hope you enjoy the Q-BT3 experience.
1 x Active Right Speaker
1 x Lithium
Battery
(3V, CR2025)
1 x UK AC
Mains Cable
1 x RCA
Phono Lead
(2 metres)
1 x EU AC
Mains Cable
1 x 3.5mm
Jack Lead
(2 metres)
2 x Sets of
Rubber Bumpers
1 x Two Pole
Speaker Cable
(4 metres)
1 x User Manual
1 x Passive Left Speaker 1 x Remote Control
Introduction
Package Contents
Page 6
Features
• 2 x 50W stereo amplier in right hand speaker
• Passive left hand speaker
• 1 x 100mm woofer and 1 x 30mm dome tweeter per speaker
• aptX® Bluetooth® input – up to 8 paired devices
• Digital optical audio input
• RCA stereo line level audio input
• 3.5mm stereo headphone level audio input
• RCA subwoofer line level audio output
• 5 button infrared remote control
Feature Summary
6
The Q Acoustics Q-BT3 is a bookshelf Bluetooth stereo speaker set designed to deliver high delity
reproduction of music, and high quality audio from a TV or set top box. The Q-BT3 is a result of careful
development and winning heritage, designed in the UK by Q Acoustics.
The Q-BT3 cabinets provide true stereo audio with no added eects or digital signal processing to colour
audio reproduction. You have peace of mind that you are listening to pure audio as the original mix
engineer intended.
The left and right speakers each have our award winning combination of 100mm woofer and 30mm dome
tweeter, providing focused channel separation, music depth and clarity, voiced by our acoustic team to
provide a full range natural sound.
Designed for simplicity, the Q-BT3 will blend into your home environment with minimal fuss yet
extraordinary improvement to your listening experience.
With both analogue and optical inputs the Q-BT3 can be used with a variety of entertainment source such
as TVs, CD players, portable music players, computers, internet radio. But that’s still not the whole story...
Q-BT3 is also Bluetooth compatible using the aptX codec for lossless audio streaming. This wireless
connection can sync to almost any Bluetooth compatible audio device. It can remember upto eight pairings,
so when friends or family come over, a ‘guest’ music player can get connected in just seconds.
Please read and follow the instructions in this manual to get the most enjoyment out of your Q-BT3.
Product Description
Page 7
No Light = O
Power cord is connected but AC switch is turned OFF.
Solid Red= O (Standby)
Power cord is connected and AC switch is turned ON,
but Q-BT3 is OFF.
Solid Green = On
Analogue input (Line in 1 or Line in 2) is the active
source.
Solid White = On
Optical input is the active source.
Quick Blue Flash = On
Bluetooth input is the active source and is currently
searching for a Bluetooth device to PAIR with.
Solid Blue = On
Bluetooth input is the active source and is PAIRED with
a Bluetooth device.
Any Colour Slow Flash = On
Currently active source is MUTED.
Instructions
TOP PANEL
1. Standby / Source Select
Long press / short press
2. Volume Down
Single press / press and hold
3. Volume Up
Single press / press and hold
4. Status LED
See LED indications below
Q-BT3 Features
7
2 1
4 3
FRONT VIEW
1 2
1. IR Sensor
The IR sensor is hidden behind the speaker grill of the active right speaker. It ‘sees’ the IR control
commands output from the Q-BT3 IR remote control when buttons are pressed.
This sensor MUST be unobstructed for direct line-of-sight to the remote, or the remote will not be
able to control the Q-BT3.
2. Rotating Badge
The Q-BT3 speakers are designed to be used in both vertical and horizontal orientations to suit
your preferred setup.
When using Q-BT3 in the horizontal orientation, you may rotate the Q Acoustics logo by gently
pulling and rotating the badge.
Page 8
Bluetooth Device:
Q-BT3-101
REAR PANEL
1
2
5
9
8
4
6
7
3
Instructions
8
1. Digital Optical Input
2. Analogue Line In 1
3. Analogue Line In 2
4. Subwoofer Out
5. Bluetooth Pair Button
6. Power Switch
7. AC Input
8. Output Speaker Terminals
9. Bluetooth Name Label
Page 9
Instructions
9
DIGITAL
1. Digital Optical Input
TOSLINK® connector for connection to the Digital Optical output on a TV or other source. If
there is a choice between Digital or Analogue connection to the Q-BT3 choose Digital for
superior audio quality. The Digital input is selected automatically if no Bluetooth device is
connected and playing. When the Digital Source is active the status LED will be WHITE.
2 & 3. Analogue Inputs Line In 1 & Line In 2
The Q-BT3 has two options for Analogue Audio connection:
Line In 1
Connect the RCA L&R audio output from a TV or other source to the LINE IN 1 sockets using
the 2m cable provided:
Important note:
Audio output of a TV, Blu-ray Disc player, game console, or DVD player connected to the Q-BT3 via Optical
Digital, must be set to PCM in the source’s setup. Please see the device’s Owner’s Manual for details. Digital
connection to a CD player does not require a special setting.
Digital Optical Audio Cable
(not included)
ANALOGUE
RCA Phono Lead (included)
Page 10
Instructions
10
Line In 2
The 3.5mm input jack is ideal for connecting to the headphone output of an external audio
source using the 2m cable provided:
The ANALOGUE INPUTS are automatically selected when Bluetooth device is connected and
playing and no Optical Digital Input signal is present. The Status LED will be GREEN when an
analogue input is in use.
Please note:
When connecting to a variable level source, such as a headphone output, better audio quality
will be achieved by having the source set at a higher volume level and the Q-BT3 at a lower
level than the other way around.
4. Subwoofer Out
Single RCA phono jack. Connect the ‘Sub Out’ to a Subwoofer Line Level Input if extended bass
response is desired.
5. Bluetooth Pair Button
The Q-BT3 has been designed to automatically search for, and PAIR with a device should no
other devices currently be PAIRED and in range. This Bluetooth Pair button is used to manually
drop the current connection and pair with a new device.
6. Power Switch
Turns the power to the Q-BT3 ON/OFF. Always turn the power OFF when making connections
to the Q-BT3 Rear Panel.
7. AC Input
Universal power connector. Automatically selects AC voltage for a given region. Connect to the
included AV Power Cord for your country.
8. Output Speaker Terminals
Connect the supplied speaker cable from the active right speaker output terminals to the
passive left speaker input terminals. Make sure to connect the WHITE STRIPE cable to the RED
positive terminal of each speaker, and the SOLID BLACK cable to the BLACK negative terminal
of each speaker.
Important note:
With a jack plugged into LINE IN 2, LINE IN 1 is switched-o and no audio will be heard from this source.
HEADPHONES
3.5mm Jack Lead (included)
Page 11
1. Power
Press this button to turn the Q-BT3 Standby ON/OFF.
(POWER SWITCH on the rear panel must be switched to ON)
2. Source Select
Press this button to manually select the audio input source.
Status LED will change colour accordingly.
3. Volume Up / Down
Press VOL + to increase the volume. Press VOL – to reduce
the volume.
4. Mute
Press this button once to MUTE the Q-BT3 (no audio output
from the speakers). Status LED will SLOW FLASH to indicate
MUTE. Press this button again to un-mute the Q-BT3 (audio
output from the speakers).
Note: Long press of Mute will also put Q-BT3 into standby.
Instructions
11
1
2
3
4
Remote Control
REMOTE CONTROL BATTERY REPLACEMENT
1. Push small tab toward
battery slot.
2. Pull battery drawer out. 3. Insert battery with “+”
side up and slide drawer
back into remote.
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent battery type (CR2025)
Warning:
Do not expose batteries to excessive heat such as direct sunlight, re or the like.
Dispose of dead batteries in accordance with local regulations.
Caution:
When replacing the lithium battery in the remote, make sure that the replacement battery is inserted in correct polarity.
Place the battery so that it’s positive (+) side faces up with the tray held so the surface with the dot and (+) is facing up.
Important note:
When the Source button is used Q-BT3 will stay on the selected
source and stop auto-source selection. Auto-source selection will
be resumed after the unit has been put in standby.
Page 12
1. Clean the surfaces of the speakers where the feet will be applied,ensuring they are free from dirt
and grease.
2. Remove the rubber bumpers from their backing paper. Take care to grip the sides rather than the
adhesive surface
3. Position the bumpers on the underside of the speakers and push rmly onto the surface. Once contact
is made the feet can not be easily repositioned.
Instructions
12
Rubber Bumpers
In order to prevent damage to the surface of other furniture, Q-BT3 is supplied with self adhesive feet which
may be applied to the underside of the speakers. Once the desired orientation of the speakers has been
selected, follow the steps below to attach the rubber bumpers to each speaker.
Page 13
Instructions
13
POWER AND STANDBY
Power on Q-BT3 at the AC SWITCH once all rear panel audio connections are made. The speakers will enter
STANDBY, with a RED status LED.
Exit STANDBY by pressing the STANDBY button on either the top panel or the IR remote. The LED will
initially turn Green but may then change according to the Auto-Source Selection rules.
AUDIO SOURCE SELECTION
In normal operation Q-BT3 will automatically select the audio source. A Connected Bluetooth source that
starts to play has the highest priority, followed by Digital and nally Analogue:
The AUDIO SOURCE auto-priority can be manually overridden at any time using SOURCE SELECT on the IR
remote or by a short press of the
button.
If NO input signals are detected, Q-BT3 will automatically enter STANDBY after 20 minutes.
SOURCE VOLUME CONTROL
Audio sources will initially be set at a DEFAULT volume level. This source can be adjusted for each source
using the VOL + and VOL – buttons on the top panel or IR remote. Once adjusted, the Q-BT3 will remember
the manually adjusted volume level for each source, and will return to the previously entered listening level
each time that source is selected.
Operating Q-BT3
Bluetooth
Optical input
Line in 2
Line in 1
Standby
INPUT
PRIORITY
Important note:
When the Source button is used on the Remote Control Q-BT3 will stay on the selected source and stop auto-source
selection. Auto-source selection will be resumed after the unit has been put in standby.
Page 14
PAIRING A BLUETOOTH DEVICE
Q-BT3 is designed to automatically go into pairing mode if there is no Bluetooth device connected. To Pair
your Bluetooth source:
1. Turn Q-BT3 and the Bluetooth device ON.
2. Make sure Bluetooth is enabled on the device to be Paired. The Bluetooth controls are typically found
in the device’s ‘Settings’ or ‘Connections’ menu.
3. On your device’s list of Discoverable devices, you should now see ‘Q-BT3-xxx’ where xxx is a pre-dened
three digit number.
4. Select ‘Q-BT3-xxx’ and your device will now be Paired via Bluetooth and Connected
5. From within the music player on your device, select ‘Q-BT3-xxx’ as the audio output and press Play. Unless
the remote has been used to manually select another source and override Auto-Source Selection the
unit will switch to Bluetooth input and the LED turn Blue.
GOING OUT OF RANGE
When a connected device goes out of range, Q-BT3 will remain on the Bluetooth channel. When the device
returns in range it will automatically re-connect to Q-BT3. In many cases PLAY must be pressed on the
device to resume audio playback. Whilst out of range, source can still be changed using the SOURCE SELECT
button.
PAIRING MORE THAN ONE BLUETOOTH DEVICE
The Q-BT3 can have up to eight Bluetooth devices in its pairing list. When you pair with the 9th device the
details of the rst device will be lost.
Once Q-BT3 is Connected with a device, it will stop automatically searching for other devices to pair with or
connect to. Under these conditions please either disconnect the currently connected source on the device
itself or press the BT Pair button on the rear panel of Q-BT3.
COMING OUT OF STANDBY
If there is a paired device in proximity to Q-BT3 when it comes out of standby it will automatically initiate a
connection to the device. It will not switch to BT input until play is pressed on the device.
Please Note:
Although starting to Play a track on the connected source will cause the Q-BT3 to switch to Bluetooth, the unit will stay
on Bluetooth until the source is disconnected. It will not switch to another source whilst the player is paused.
Please Note:
If the source does not come back into range for 20 minutes the unit will automatically go into standby.
Please Note:
When connected the device’s volume and mute controls control the device itself, not Q-BT3. Better audio quality will be
achieved by having the device set at a higher volume level and the Q-BT3 at a lower level.
Instructions
14
Page 15
CABLE/SATELLITE REMOTE CONTROL
The Q-BT3 has been designed for easy integration into your home entertainment system as it has the
ability to be controlled by many types of PROGRAMMABLE REMOTE CONTROL. This may include the remote
control for your SATELLITE and CABLE system if it has PUNCH THROUGH capability. Punch through is the
common term for being able to programme your remote control to send IR codes to both a TV and an AV
Preamplier/Processor. To use punch through you normally select the TV you wish to support rst, and then
the AV Preamplier/Processor.
Q-BT3 uses the PHILIPS RC5 protocol for AV Preampliers/Processors. Programming your remote with
PHILIPS AV codes should allow you to control volume and mute of your Q-BT3. In some cases you may also
be able to control standby and source select with buttons such as and .
Manufacturers often oer several PHILIPS code options for their remote controls. We recommend that you
work through the PHILIPS code list for your remote and experiment with each one until you nd one that
works well with the Q-BT3. It is easiest to recognise when one is working by pressing the volume up/down
buttons.
We cannot guarantee that Q-BT3 will work with your particular remote as the IR codes it sends are outside
our control, however by supporting the commonly used Philips standard we hope to have made it as easy
as possible to gain control of your device with the remote control of your choice.
• Press the “TV” button (top left of remote).
• Point remote away from receiver,
press and hold “Select + 0”.
• The remote’s LED will ash red twice.
• Enter “1217”. The remote’s LED will ash
red twice to conrm correct code.
• Press and hold “Select + 1”.
• The remote’s LED will ash red twice.
• Press TV and your remote controls will now work
as such:
Button Function
Vol + Volume up
Vol - Volume down
Mute
(short press) Mute
or Mute
(long press) Standby
Source select
Instructions
15
TYPE 1
TV
1
+
2
3
6
5
4
7
8
9
0
SELECT
VOL
MUTE
Volume up / down
Mute / Standby
Standby
Source select
Page 16
TV
1
2
3
6
5
4
7
8
9
0
VOL
CLEAR
MUTE
Instructions
16
TYPE 2
Volume up / down
Mute / Standby
• Press the “TV” button (top right of remote).
• Point remote away from receiver,
press and hold “Clear + Vol ”.
• The remote’s LED will ash green twice.
• Enter “1247”. The remote’s LED will ash
green twice to conrm correct code.
• Press TV and your remote controls will now work
as such:
Button Function
Vol
Volume up
Vol
Volume down
Mute
(short press) Mute
Mute
(long press) Standby
Page 17
Specication
17
Audio performance
Power output: 2 x 50W for 100W total amplication
THD (at rated power): <1.00%
Frequency response: ±0.5dB 20Hz to 20kHz
S/N ratio (A-Wtd): -85dB
Line in 1 input sensitivity: 2.0Vrms
Line in 1 input overload: 2.2Vrms
Line in 2 input sensitivity: 1.0Vrms
Line in 2 input overload: 1.2Vrms
Speakers
Enclosure type: 2-way reex
Mid range driver: 100mm
Tweeter: 30mm
Power consumption
Standby: <0.5 Watts
No signal (idle): 14 Watts
Rear panel marked line ratings: 100~240V - 50~60Hz 100W
Bluetooth®
Bluetooth specication: V4.0 class 2 device
Latency: ≈6ms
Internal stereo CODEC: 16-bit
High quality stereo audio: ≤48kHz sample rate
Music enhancements: aptX®, SBC, MP3
Support for: A2DP, 802.11 co-existence
Dimensions
(H x W x D): 240mm x 148mm x 208mm
Depth including terminals: 226mm
Weight
Active right speaker: 3.8kg
Passive left speaker: 3.4kg
Total weight: 7.2kg
Specification
Page 18
Warranty
18
Q Acoustics products are warranted free of defects in materials and workmanship for a period of 2 years
from the date of purchase. During the warranty period Q Acoustics will, at its option, repair or replace any
product found to be faulty after inspection by the company or its appointed distributor or agent.
Misuse and fair wear and tear are not covered by warranty.
Goods for repair should in the rst instance be returned to the supplying dealer. If this is not possible the
item/s should be sent carriage paid preferably in the original packaging to Q Acoustics or their appointed
distributor for your area and accompanied by proof of purchase. Damage sustained by goods in transit
to the repair centre is not covered by the warranty. Return carriage will be paid by Q Acoustics or their
distributor as appropriate.
The warranty does not in any way aect your legal rights.
Appointed Distributor Warranty Agent in the UK:
Armour Home Electronics Ltd.
Stortford Hall Induistrial Park
Bishops Stortford, Herts, UK
CM23 5GZ
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Armour Home
Electrioncs Ltd. is under license. The aptX® mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be
registered in one or more jurisdictions. Other trademarks and trade names are those of their respective owners.
Q Acoustics Warranty
Page 19
Page 20
www.Qacoustics.co.uk
Q13924-IS_r0
Loading...