Page 1
Step4:Step4:
1.Vertical title
1.Vertical title
Loosen tilt tension screws with supplied Hex Wrench .Adjust display for
desired tilt angle ,and then re-tighten tension screws .As shown in Fig4a .
2.Roll control in little range
2.Roll control in little range
Loosen left and right tension screws with supplied Hex Wrench .Adjust
display for desired angle ,and then re-tighten tension screws .As shown
in Fig4b .
3.Roll control in great range
3.Roll control in great range
Pull the display ,make distance between display and wall is maximum .
Circumvolve display in horizontal direction, adjust it for desired angle .
As shown in Fig4c .
Flat Panel Fixed Mount
INSTALLATION GUIDE
4.Withdraw the display
4.Withdraw the display
fold the Bracket to shorten the distance between display and wall ,let
display cling the wall in vertical direction .
Item No.:PWLB121Item No.:PWLB121
TV size rang 10 24：" "~
Max load capacity:15Kg/33lbs
According to VESA 75/100 standard
Can tilt and fold the Bracket
-4--4Important: If don't understand about right install ways, please
Important:
consult to normal installing specialist.
Page 2
Parts:Parts:
Wall bracket
A
NO
Qty
A
B
C
D
E
Fixed plate
F
G
D
C
B
EF
G
4
4
4
4
2
2
1
Name
M4 8mm bolt
M5 8mm bolt
M4 mm bolt12
M5 12mm bolt
Long bolt
Wall anchor
Hex Wrench
Step2 nfold the Arm Assembly:UStep2 nfold the Arm Assembly:U
Use wall mount as templet,let Bracket flex at the position determined before.
And making a mark in the center of batten.
If mounting to cement and beton wall,making mark on the wall directly.
Note:
Note:
Wood en
Wooden Studs
Cement and Beton
Cement
Studs
and Beton
Insert wall anchors(F) into the mounting holes and slightly tap them flush
to the wall with a hammer.
Carefully:
Carefully:
Never use wall anchors in drywall to install bracket.
Using provided Long bolt install Bracket to the wall.
Step3: Intalling displayStep3: Intalling display
Check your TV manual and confirm the diameter of bolts to be use ,or choose
appropriate bolts according to size ,heigh ,and position of the holes on your
Step1 Choose your installing location on the TV panel:.
Step1 Choose your installing location on the TV panel:.
Considering display with varied”VESA”
standard connects with stand directly. This
product establishes two kinds of installing
TV .Put up the TV with an assistant in fitting position on the Mounting head.
As shown in Fig 2.
Carefully :DDon't force the bolt to LCD hole ,avoiding damage to people or
Carefully :
instrument. on't use electronics drill to fasten screw .
styles which is according with “ VESA”
standard.
A-VESA 75(75mmx75mm)
B-VESA 100(100mmx100mm)
Fig2
If the installing hole of your display is not
”VESA” standard, you need an optional
carrying instrument to attach the display to
the stand.If need carrying instrument,
pleasecontactwithyourdealer.
Fig1
Use a 3mm drill bit,and dill 50mmdeepholes.
—
—
Use a 11mm drill bit, and dill 50mm deep holes.
—
—
Wall anchor should only be used for Cement and Beton mounting.
Shoulder Tension
Swing Arm Tension
Wrist Hinge Tension
Important:Make sure that there is adequate mounting space available for the
Important:
display,considering the display dimensions.Using a electronic stake detector
in that mounting location,which is in center of stake.Making mark in the center
of stake on the wall directly .
-2-
Fig3
Wall Mount Plate
Tilt Tension
Mounting Head
-3-
Loading...