TOXIC™ & ENIGMA
™
CROSSBOW
®
OWNER’S GUIDE
READ THESE INSTRUCTIONS CAREFULLY BEFORE
FANG CROSSBOW
READ THESE INSTRUCTIONS CAREFULLY BEFORE
OPERATING YOUR PSE CROSSBOW.
OWNER’S GUIDE
OPERATING YOUR PSE CROSSBOW
PRECISION SHOOTING EQUIPMENT, INC. • WWW.PSE-ARCHERY.COM
DISTRIBUTED BY:
®
®
CROSSBOW OWNER’S GUIDE
Thank you for purchasing your new PSE crossbow!
With proper use and care your crossbow will provide
years of enjoyment. Keep this manual with your crossbow
for reference.
LIMITED LIFETIME WARRANTY
PSE warranties every compound crossbow to be free of
defects in material and workmanship for the period as
dened below.
1) PSE crossbow stocks, metal prods and cams, if
defective, will be replaced at no charge for the
lifetime of the product.
2) Limbs, if defective, will be replaced at no charge for the
rst year, and at 50% of the replacement cost thereafter
for the life of the product.
3) Evidence of mishandling, abuse or modication of the
product or use of non-PSE replacement parts voids the
warranty.
4) Cables, strings, cable slides, and vibration dampers are
wearable items and are not covered by this warranty.
All warranty work will be performed by PSE or your local
PSE Crossbow dealer.
PSE makes no other warranty claims whether expressed or
implied. This warranty applies to the original owner only, and
does not cover cables, strings, or vibration dampers.
NOTE: This manual covers only the Fang PSE crossbow
model. If this is the incorrect manual for your crossbow
model, please contact PSE Customer Service.
2
®
SAFETY
1) ALWAYS treat your crossbow as you would any weapon
or rearm. It is a powerful weapon that can be deadly if
mishandled.
2) ALWAYS keep your crossbow pointed in a safe direction.
Never point your crossbow at anything you don’t intend to
shoot.
3) NEVER enter a vehicle with a loaded crossbow. Always
uncock and properly stow your crossbow for transporting.
4) ALWAYS check your crossbow to make sure that it is in
proper mechanical order. Check for damaged, worn, loose
or missing parts.
5) NEVER DRY FIRE YOUR CROSSBOW. Firing the
crossbow without a bolt will cause damage not only to the
crossbow but possible bodily injury to you and anyone in the
area. It also voids the warranty.
6) DO NOT make changes or alterations to any parts of this
crossbow as it may cause an unsafe condition and will void
the warranty.
7) NEVER release the safety on your crossbow until you are
ready to shoot and are sure of your target.
8) NEVER shoot any bolt or other projectile from your
crossbow that has not been recommended by PSE. Use
only bolts of the proper size, weight and length.
9) ALWAYS keep your ngers and thumb out of the path of the
string and cables while shooting your crossbow. Failure to
do so will cause injury.
10) ALWAYS wear safety glasses when handling a crossbow.
WARNING:
Use extreme caution while operating this weapon. Never run,
crawl, ride a horse, operate an ATV, motorcycle or travel in a
vehicle with a loaded crossbow. Accidental discharge could
prove harmful or fatal.
3
®
Lightweight Integrated
Synthetic Stock/Barrel
Prod Assembly
CROSSBOW OWNER’S GUIDE
FANG CROSSBOW COMPONENTS
Precision Trigger / Auto Safety
Rope Cocking Groove
4x32 Multi-Range Scope
Comfort Molded Grip
Full Barrel Picatinny Rail
Cam
Limbs
Large Boot Style Foot
Stirrup
Before assembling your crossbow (Fig. 1), please check to see if all crossbow parts are
included: 1- Prod, 1- Stock, 3 - Crossbow Bolts, and 1 - Cocking rope (Fig. 1a), 1 - Prod
Bolt, 2 - Washers, 4 - Allen Wrenches, 1 - Rail Lube (not shown), 1 - Quiver Mount, 1 -
Foot Stirrup, and 1-Quiver (Fig. 2). If any of these parts are missing please contact PSE
Customer Service.
Cable slide should come installed. If it is not, please attach cable slide to the cables with the
concave area facing up and the cables in the two grooves as shown. Fig. 3
Connect the barrel and the riser by inserting the cable slide and cables into the slot on the
barrel as shown in Fig. 4a. Be sure the concave side is facing up to match with the contour
on the inside of the barrel.
Push the cables into the track and position the riser for connection to the barrel using the
prod bolt and washer and hex key provided. Tighten the center set screw to lock the barrel
connector, in order to hold the riser in the correct position. Fig 4b.
Insert the foot stirrup into the two holes on the front of the riser. Fig 5a. Make sure the two
notches in the foot stirrup are facing towards the set screws used to secure the stirrup.
Fig. 5b
Quiver
Adjustable Picatinny
Mounted Foregrip
Fig. 1
4