PowerScan
®
7000BT SRI
Linear Imager
Quick Reference Guide
PSC Inc
959 Terry Street
Eugene, Oregon 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures
described therein may be reproduced or transmitted in any form or by any means without prior written per-
mission of PSC Inc. or its wholly owned subsidiaries ("PSC"). Owners of PSC products are hereby granted
a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own
internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copy-
right notices, contained in this documentation and shall ensure that all notices appear on any reproduc-
tions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your
PSC representative. Electronic versions may either be downloadable from the PSC website
(www.psc.com) or provided on appropriate media. If you visit our website and would like to make com-
ments or suggestions about this or other PSC publications, please let us know via the “Contact PSC” page.
Disclaimer
PSC has taken reasonable measures to provide information in this manual that is complete and accurate,
however, PSC reserves the right to change any specification at any time without prior notice.
PSC is a registered trademark of PSC Inc. The PSC logo is a trademark of PSC. All other trademarks and
trade names referred to herein are property of their respective owners.
This product may be covered by one or more of the following patents: 4603262 • 4639606 • 4652750 • 4672215 • 4699447
• 4709369 • 4749879 4786798 • 4792666 • 4794240 • 4798943 • 4799164 • 4820911 • 4845349 • 4861972 • 4861973 •
4866257 • 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 • 4971177 • 4991692 • 5001406 •
5015831 • 5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 • 5200597 • 5202784 •
5208449 • 5210397 • 5212371 • 5212372 • 5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 • 5237161 •
5237162 • 5239165 • 5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 • 5298728 • 5311000 •
5327451 • 5329103 • 5330370 • 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 •
5422472 • 5426507 • 5438187 • 5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 •
5479011 • 5481098 • 5491328 • 5493108 • 5504350 • 5508505 • 5512740 • 5541397 • 5552593 • 5557095 • 5563402 •
5565668 • 5576531 • 5581707 • 5594231 • 5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 •
5635699 • 5641958 • 5646391 • 5661435 • 5664231 • 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 •
5703347 • 5705802 • 5714750 • 5717194 • 5723852 • 5750976 • 5767502 • 5770847 • 5786581 • 5786585 • 5787103 •
5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721 • 5822343 • 5825009 • 5834708 • 5834750 • 5837983 •
5837988 • 5852286 • 5864129 • 5869827 • 5874722 • 5883370 • 5905249 • 5907147 • 5923023 • 5925868 • 5929421 •
5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 • 6012639 • 6016135 • 6024284 • 6041374 • 6042012 •
6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 • 6073851 • 6094288 • 6112993 • 6129279 •
6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614 • 6173894 • 6176429 • 6188500 •
6189784 • 6213397 • 6223986 • 6230975 • 6230976 • 6237852 • 6244510 • 6259545 • 6260763 • 6266175 • 6273336 •
6276605 • 6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576 • 6332577 •
6343741 • 6454168 • 6478224 • 6568598 • 6578765 • 6705527 • 6974084 • 6991169 •7051940 • AU703547 • D312631 •
D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 • D350127 • D350735 • D351149 • D351150
• D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 • D374630 • D374869 • D375493 •
D376357 • D377345 • D377346 • D377347 • D377348 • D388075 • D446524 • EP0256296 • EP0260155 • EP0260156 •
EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 • EP0531645 • EP0663643 •
EP0698251 • GB2252333 • GB2284086 • GB2301691 • GB2304954 • GB2307093 • GB2308267 • GB2308678 •
GB2319103 • GB2333163 • GB2343079 • GB2344486 • GB2345568 • GB2354340 • ISR107546 • ISR118507 •
ISR118508 • JP1962823 • JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 • MEX185552 •
MEX187245 • RE37166 • Other Patents Pending
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Class B Compliance Statement
The user is cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio or television technician for help.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits under Specific Absorption Rate
(SAR) tests for portable devices operating closer than 20 cm to nearby persons, set forth in an
uncontrolled environment. The PowerScan 7000BT handheld scanner has been demonstrated to
meet these RF emissions safety limits.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as described in the
Radio Interference Regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables
aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique
edicte par le ministere des Communications du Canada.
Power Supply
This product may require an external power supply (AC Adapter). Use only a PSC power supply
approved exclusively for use with this product and is a model Listed Class 2 or Listed LPS power
source which supplies power directly to the Base Station.
Solids and Water Protection
The Imager is rated as IEC 529-IP65. This nomenclature designates the degree of water and dust
resistance, indicating the imager is totally protected against dust and is protected against low pressure jets of water from all directions - limited ingression permitted.
Quick Reference Guide i
The Base Station is rated as IEC 529-IP54, indicating the unit is protected against dust, limited
ingress (no harmful deposit) and is protected against water sprayed from all directions - with limited
ingression permitted.
PSC INC. POWERSCAN
Notice to End User: The PSC Product you have acquired contains embedded Software, which is integral to
the product’s operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the PSC Product, you will be deemed to have accepted the terms and
conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, PSC is not
willing to license the Software to you, you may not use the PSC Product or the Software, and you must contact the party from whom you acquired the PSC Product for instructions.
This End User Software License Agreement (“Agreement”) is a legally binding agreement governing the licensing of
the Software and Documentation by PSC Inc. and its wholly owned subsidiaries and affiliates (“PSC”) to the entity or
person who has purchased or otherwise acquired a PSC Product (“End User”). For purposes of this Agreement, any
software that is associated with a separate end-user license agreement is licensed to you under the terms of that
license agreement. PSC and End User hereby agree as follows:
1. Definitions.
1.1 "Documentation" means materials such as user’s guides, program reference guides, quick reference guides,
manuals, or similar materials associated with or related to the PSC Product, whether in printed, “online”, or
other form.
1.2 "Proprietary Information" means: (a) source code, object code, software, documentation, and any related
internal design, system design, data base design, algorithms, technology, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the
circumstances, should recognize as confidential. Proprietary Information does not include any information that
the receiving party can establish was (1) in the public domain, (2) already in the receiving party’s possession
or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's proprietary rights, or (4) independently developed without access to Proprietary Information.
1.3 “PSC Product” means the PSC Powerscan® series, Powerscan® Imager series, Powerscan® EP series, Powerscan® LR series, Powerscan® HD series, and/or Powerscan RF® series scanner and/or scanner/scale product, including all embedded Software in and all Documentation related to such product, which has been
purchased or otherwise acquired by End User, whether obtained directly or indirectly from PSC.
1.4 "Software" means any software or computer programs of PSC or its third party licensors in machine readable
form which is embedded in the PSC Product, whether obtained directly or indirectly from PSC, including any
replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted.
2.1 PSC grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solely on
the PSC Product in which it is embedded (“designated PSC Product”), in machine-readable form only, solely
for End User's internal business purposes. This Agreement does not convey ownership of the Software to
End User. Title to the Software shall be and remain with PSC or the third party from whom PSC has obtained
a licensed right. As used in this Agreement, the term “purchase” or its equivalents when applied to the Software shall mean “acquire under license.” End User is not entitled to receipt or use of the source code to any
Software.
2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give,
or otherwise transfer the Software to any other person or organization, for purposes other than as expressly
provided in this Agreement, without PSC’s prior written consent.
3. Transfers, Support.
3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of
the Software on other than the designated PSC Product will be a material breach of this Agreement. However,
PSC may elect not to terminate this Agreement or the granted licenses, but instead may elect to notify End
User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall
pay PSC the applicable list price for such licenses as of the date of such breach.
3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the PSC Product
to any third party unless such third party agrees with PSC in writing to be bound by the terms and conditions
of this Agreement. Any such transfer of the PSC Product absent such agreement shall be null and void.
3.3 End User may obtain support for Software from PSC at PSC’s standard support fees and under PSC’s standard support terms and conditions in effect at the time the support is requested.
4. Intellectual Property.
End User acknowledges that the Software constitutes valuable trade secrets of PSC or PSC’s third party licensors
and that the Software is protected by intellectual property laws and treaties. The license set forth in this Agreement
does not transfer to End User any ownership of PSC’s or its third party licensors' copyrights, patents, trademarks,
service marks, trade secrets, or other intellectual property rights and End User shall have no right to commence any
legal actions to obtain such rights. End User shall not remove, modify, or take any other action that would obscure
any copyright, trademark, patent marking, or other intellectual property notices contained in or on the PSC Product.
5. Proprietary Information.
5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret property
of PSC and PSC’s third party licensors and End User acquires no right or interest in any Proprietary Informa-
®
END USER LICENSE AGREEMENT
ii PowerScan® 7000BT SRI
tion.
5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Information of PSC or its
third party licensors to any person other than End User’s authorized employees or agents who are under confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction with
use of the PSC Product exclusively for End User’s internal business purposes. End User shall take steps to
protect the Proprietary Information no less securely than if it were End User's own intellectual property.
5.3 The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement.
6. Limited Warranty.
6.1 PSC warrants that, under normal use and operation, the PSC Product will conform substantially to the applicable Documentation for the period specified in the Documentation. During this period, for all reproducible
nonconformities for which PSC has been given written notice, PSC will use commercially reasonable efforts to
remedy nonconformities verified by PSC. End User agrees to supply PSC with all reasonably requested information and assistance necessary to help PSC in remedying such nonconformities. For all defects reported to
PSC within the warranty period, PSC’s liability is limited to providing End User with one copy of corrections or
responding to End User's problem reports according to PSC's standard assistance practices. PSC does not
warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or
error free, or that PSC's remedial efforts will correct any nonconformance. This limited warranty does not
cover any product that have been subjected to damage or abuse, whether intentionally, accidentally, or by
neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in any manner other than as established in the Documentation, or if End User breaches
any of the provisions of this Agreement.
6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE PSC PRODUCT IS PROVIDED “AS IS” AND PSC
MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL, WITH RESPECT
TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
7. Infringement.
7.1 PSC will defend End User against any claim in a lawsuit that the PSC Product furnished hereunder infringe a
United States patent or copyright of a third party and PSC will pay any damages finally awarded against End
User by a court of competent jurisdiction that are attributable to such claim or will pay End User’s part of any
settlement that is attributable to such claim, provided, that 1) End User notifies PSC promptly in writing of the
claim, 2) PSC controls the defense or settlement of the claim, and 3) End User cooperates fully with PSC in
such defense or settlement. All notices of a claim should be sent to PSC Inc., Legal Department, 111 SW
Fifth Ave. Suite 4100, Portland, OR 97204-3644.
7.2 In the defense or settlement of any such claim, PSC may, at its option, 1) procure for End User the right to
continue using the PSC Product, 2) modify the PSC Product so that it becomes non-infringing, 3) replace the
PSC Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to
return the PSC Product and receive a refund of the purchase price paid, less a reasonable allowance for use.
7.3 PSC shall have no liability to End User for claims of infringement based upon 1) the use of any PSC Product
in combination with any product which PSC has not either furnished or authorized for use with such PSC
Product 2) the use of any PSC Product designed, manufactured, or modified to the specifications of End User,
or 3) End User’s modification of the PSC Product without written authorization from PSC.
7.4 THE FOREGOING STATES PSC’S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF
PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND
SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES
CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL
OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.
8. Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, PSC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER
BY ANY OTHER PARTY. IN NO EVENT SHALL PSC'S LIABILITY FOR DAMAGES, IF ANY, WHETHER BASED
UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY,
OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE PSC PRODUCT. UNDER
NO CIRCUMSTANCES SHALL PSC BE LIABLE TO END USER OR ANY THIRD PARTY FOR LOST PROFITS,
LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL,
CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF
PSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR
52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013(c)(1)(ii), whichever is applicable.
9.2 If End User is using the PSC Product outside of the United States, End User must comply with the applicable
local laws of the country in which the PSC Product is used, with U.S. export control laws, and with the English
language version of this Agreement. The provisions of the “United Nations Convention on International Sale
of Goods” shall not apply to this Agreement.
10. Termination.
10.1 Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provision of this Agreement.
10.2 Upon termination of this Agreement, End User immediately shall cease using any non-embedded software
and shall return to PSC or destroy all non-embedded software covered by this Agreement, and shall furnish
PSC with a certificate of compliance with this provision signed by an officer or authorized representative of
End User. For embedded software, End User agrees to sign a waiver prepared by PSC concerning further
use of the embedded Software. End User’s resumed or continued use of the embedded Software after termi-
Quick Reference Guide iii
nation shall constitute End User’s agreement to be bound by the terms and conditions of this Agreement for
such use.
11. General Provisions.
11.1 Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to
the licensing of the Software and supersedes all prior or contemporaneous agreements, written or oral,
between the parties concerning the licensing of the Software. This Agreement may not be changed,
amended, or modified except by written document signed by PSC.
11.2 Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective
when received, with evidence of receipt. Notices to PSC shall be sent to the attention of Contract Administration, PSC Scanning Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by
PSC in writing.
11.3 Waiver. A party’s failure to enforce any of the terms and conditions of this Agreement shall not prevent the
party’s later enforcement of such terms and conditions.
11.4 Governing Law; Venue:This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane counties
shall have exclusive jurisdiction over all matters regarding this Agreement, except that PSC shall have the
right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory in
which End User resides, or in which any of End User's assets are located.
11.5 Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this Agreement, the
prevailing party shall be entitled to reasonable attorneys’ fees, both at trial and on appeal.
- END -
Software Product Policy
PSC reserves the right to ship its products with the latest version of software/firmware available.
This provides our customers with the very latest in PSC software technology.
The only exception to this policy is when the buyer has a signed contract with PSC that clearly
defines the terms and conditions for making software/firmware changes in products shipped to the
buyer.
Customers Under Software Support
Customers that elect to subscribe to PSC Software Maintenance and Support Agreement will receive
30 days advance notification of: (1) the release of a new software version; and/or (2) discontinuation
of any prior software version that will no longer be supported. PSC will provide maintenance for a
fee that will assist customers in transitioning to the next software version. If a customer is currently
using the software version being discontinued, the customer may elect to transition to any one of the
newer versions, depending on the hardware in use.
To arrange for a Software Maintenance and Support Agreement please contact your PSC sales person.
Laser Cautions
The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S.
to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC
60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous. Laser
pointer models of the imager contain a Visible Laser Diode (VLD) at a wavelength of 655 nanometers and is designed so that there can be no human access to harmful levels of laser light during normal operation, user maintenance, or during prescribed service operations. See the Product Reference
Guide (PRG) for laser pointer configuration information and bar codes.
Do not attempt to open or otherwise service any components in the
optics cavity. Opening or servicing any part of the optics cavity by unau-
thorized personnel may violate laser safety regulations.
CAUTION
iv PowerScan® 7000BT SRI
Table of Contents
Statement of Agency Compliance ............................................................ i
FCC Class B Compliance Statement ................................................... i
FCC RF Radiation Exposure Statement ......................................... i
Canadian Notice ............................................................................. i
Power Supply ................................................................................. i
Solids and Water Protection ............................................................. i
Software Product Policy ....................................................................... iv
Customers Under Software Support ................................................ iv
Laser Cautions ............................................................................. iv
Getting Started ................................................................................... 1
Installing the Battery Pack .............................................................. 1
Verifying Scanner Operation Before Linking to the Base Station ........... 3
Connection ................................................................................... 4
Linking the Scanner to a Base Station .............................................. 5
Linking the Scanner to a Bluetooth Device ........................................ 6
Battery Pack Charging and Maintenance ........................................... 7
Programming ................................................................................ 8
Interface Selection ................................................................... 9
Resetting the Standard Product Defaults ......................................... 13
How to Scan ..................................................................................... 14
Troubleshooting ................................................................................ 15
Troubleshooting the RF System ..................................................... 15
Troubleshooting the Scanner ......................................................... 16
Quick Reference Guide v
vi PowerScan® 7000BT SRI
Getting Started
Installing the Battery Pack
To charge the Battery Pack, See “Battery Pack
Charging and Maintenance” on page 7.
PSC recommends annual replacement of recharge-
NOTE
WARNING
able battery packs to ensure maximum performance.
Do not discharge the battery using any device except for the scan-
ner. When the battery is used in devices other than the linear imager,
it may damage the battery or reduce its life expectancy. If the device
causes an abnormal current to flow, it may cause the battery to
become hot, explode or ignite and cause serious injury.
Lithium-ion battery packs may get hot, explode or ignite and cause
serious injury if exposed to abusive conditions. Be sure to follow the
safety warnings listed below:
• Do not place the battery pack in fire or heat.
• Do not connect the positive terminal and negative terminal of
the battery pack to each other with any metal object (such as
wire).
• Do not carry or store the battery pack together with metal
objects.
• Do not pierce the battery pack with nails, strike it with a ham-
mer, step on it or otherwise subject it to strong impacts or
shocks.
• Do not solder directly onto the battery pack.
• Do not expose the battery pack to liquids, or allow the battery
to get wet.
In the event the battery pack leaks and the fluid gets into your eye,
do not rub the eye. Rinse well with water and immediately seek med-
ical care. If left untreated, the battery fluid could cause damage to
the eye.
Quick Reference Guide 1
CAUTION
Always charge the battery at 32° – 113°F (0° - 45°C) temperature
range.
Use only the authorized power supplies, battery pack, chargers, and
docks supplied by your PSC reseller. The use of any other power
supplies can damage the linear imager and void your warranty.
Do not disassemble or modify the battery. The battery contains
safety and protection devices, which, if damaged, may cause the bat-
tery to generate heat, explode or ignite.
Do not place the battery in or near fire, on stoves or other high tem-
perature locations.
Do not place the battery in direct sunlight, or use or store the battery
inside cars in hot weather. Doing so may cause the battery to gener-
ate heat, explode or ignite. Using the battery in this manner may also
result in a loss of performance and a shortened life expectancy.
Do not place the battery in microwave ovens, high-pressure contain-
ers or on induction cookware.
Immediately discontinue use of the battery if, while using, charging
or storing the battery, the battery emits an unusual smell, feels hot,
changes color or shape, or appears abnormal in any other way.
Orient the Battery Pack as shown in Figure 1, then push it into the scanner until the alignment pins engage and the unit snaps into place (the
pins will not engage if the Battery Pack is incorrectly oriented). To
remove the Battery Pack, push in on the release latches on either side of
its base and pull it straight out of the scanner.
2 PowerScan® 7000BT SRI
Getting Started
Figure 1. Battery Pack Installation & Removal
Scanner
Alignment Pins
Battery
Pack
Release Latch
Release Latch
Verifying Scanner Operation Before Linking
to the Base Station
Once a charged Battery Pack has been installed in the scanner, scan a
1
good sample bar code of the symbology
grammed to read. If unsure how to do this, see the section on
Scan
in this manual. Tip: The part number bar code on the back cover
of this manual is a Code 39 symbology sample.
The system may signal with one or a combination of indicators depending upon how the scanner and Base Station are programmed to respond
(see LED and Beeper Indications for details). If your scanner fails to read
a sample bar code of a symbology it is programmed to read, turn to the
section titled,
Troubleshooting.
type your scanner is pro-
How to
1. To enable more bar code symbology types, reference the Product Reference Guide
(PRG).
Quick Reference Guide 3
Connection
Figure 2 shows how to connect the Base Station to a terminal, PC or
other host device. Turn off the host before connection and consult the
manual for that equipment (if necessary) before proceeding.
Base Station Connection and Routing —
1
Cable
the underside of the Base Station (see
and Interface (I/F) Cable connectors into their respective ports in
Figure 2). Alternatively, you can
Fully insert the Power
either loop the cables around the routing clips and back through the
routing channel to the front of the Base Station as shown, or the cables
can be fed directly out the back of the Base Station via the routing clips.
Figure 2
. Connecting the Base Station
Power Cable
I/F
Cable
Routing
Routing
Channel
Clips
Bottom of Base Station
I/F Cable
Optional
AC Adapter
Station
Host Connection —
The interface type was specified at the time your
Base
Power Cable
scanner was ordered, however you should verify before connection that
the scanner’s cable type is compatible with your host equipment. Most
connections plug directly into the host device as shown in
Figure 3. Key-
board Wedge interface cables have a ‘Y’ connection where its female end
mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.
1. The AC Adapter (Power Cable) is an optional device used only if the host/terminal cannot
by itself supply adequate power to drive the Base Station (via the interface cable).
4 PowerScan® 7000BT SRI
Figure 3. Connecting to the Host
B
S
K
U
e
y
W
b
o
e
or...
2
3
2
-
S
R
or...
a
d
r
d
g
e
Getting Started
or...
M
B
I
Optional Power Connection —
If needed1, plug the AC Adapter in
to an approved AC wall socket with the cable facing downwards (as
shown in
Figure 2) to prevent undue strain on the socket.
Linking the Scanner to a Base Station
To link a scanner to a Base Station, press the Link Button on the Base
Station (see
Mode"then scan the “
bar code located on the Base Station itself using the scanner to be linked.
Allow the system several seconds to create the association between the
two units and exit Link Mode. A successful link is indicated by three
ascending tones from the scanner. A “high-low-high-low” tone indicates
the link attempt was unsuccessful. A single LED flash during this tone
indicates no Base Station was discovered. Two green LED flashes during
this tone indicates that more than one Base Station was discovered and
the scanner did not link.
Figure 4) for at least one second to place the base in "Link
Link to a Base Station” bar code below or the link
1. The AC Adapter (Power Cable) is an optional device used only if the host/terminal cannot
by itself supply adequate power to drive the Base Station (via the interface cable).
Quick Reference Guide 5
Link to a Base Station
Figure 4. Labeling and Nomenclature
This illustration shows label placement ONLY.
For actual regulatory, patent and other applicable
information, view the labels on the product intself,
or call your nearest sales or service office.
Scanner
Scan
Window
Tri gg er
This product is covered by patents listed in the product manual
Laser Radiation — Do not stare into Beam
1mW — 650 nm Class 2 Laser Product
Based on 10 sec — EN60825-1:2001
2005-04-18
Class No: PS7000-123400-1200
Model PS7000
This product is convered by patents listed in the
I/F: RS-232
product manual and at www.psc.com/patents.
S/N and Laser Safety Label
Complies with 21CFR 1040 Rules
and at www.psc.com/patents.
Avoid Exposure — Laser Radiation is Emitted from this Device.
S/N: B000001
Battery Pack
PSC Inc.
959 Terry St
Eugene, OR
97402 USA
Indicator
LEDs
Speaker
Port
Battery Latch
Link
Button
Amber LED
Green
LED
Scanner
Latch
Antenna
Link Bar Code
Base Station
Regulatory
Label
Linking the Scanner to a Bluetooth Device
A scanner can optionally be linked to a PC with a Bluetooth radio
installed.
1. Ensure that the Bluetooth device and its driver are installed on the
PC.
2. On the PC, open the control window for the Bluetooth device
(usually called “My Bluetooth Places”). Follow the instructions for
the Bluetooth device to disable the security setting for the Bluetooth serial port.
3. Scan the “
Link to a PC” bar code below.
Link to a PC
6 PowerScan® 7000BT SRI
Getting Started
4. On the PC, search for Bluetooth devices that are in range and
select the “PSC PS7000 Scanner.”
5. Connect with the serial port for the PSC PS7000 Scanner. Note
which serial port number is assigned to the scanner.
6. Open your serial port application and connect to the scanner using
the serial port that was assigned in the previous step.
Battery Pack Charging and Maintenance
The Amber LED will blink twice when a bar code is
decoded when the battery is getting low.
NOTE
Seat the scanner (with installed Battery Pack) in a powered Base Station
as shown in
engages the station’s metal contacts. The scanner will sound a short
“chirp” when good contact is made and the green LED on the Base Station should flash, indicating the battery is charging. Alternatively, multiple Battery Packs can be charged external to the scanner using an
accessory charging unit available from your PSC dealer.
Figure 5, ensuring the Battery Pack is fully seated and
There presently are no US, North America or World disposal requirements for Lithium-Ion batteries such as the Battery Pack, so when they
won't hold a charge anymore they can be disposed of; preferably through
a recycling center. Contact your local government for disposal or recycling practices in your area.
Quick Reference Guide 7
Figure 5. Charging the Battery Pack in a Docked Scanner
Programming
The scanner is typically factory-configured with a set of default features
standard to the interface type you ordered. You can select other options
and customize your scanner through use of the instructions and programming bar codes available in the Product Reference Guide (PRG).
You can view and download this and other manuals from the website
listed on the back cover of this manual.
8 PowerScan® 7000BT SRI
Getting Started
Interface Selection
Select the desired interface by scanning the associated bar code below.
For Keyboard Wedge interfaces, see
keyboard types.
INTERFACE SELECTION BARCODE
RS-232
Standard
RS-232
Wincor-Nixdorf
Wand
Emulation
Ta bl e 1 -1 for a listing of associated
IBM 4683
Por t 5B
IBM 4683
Por t 9B
IBM 4683
Por t 17
Quick Reference Guide 9
INTERFACE SELECTION BARCODE
IBM USB
USB HID
Keyboard
USB HID POS
Table 1-1. Keyboard Wedge Interface Reference
I/F Type PCs Supported
A PC/XT w/Alternate Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key
B
Encoding
C PS/2 25 and 30 w/Alternate Key Encoding
D PC/XT w/Standard Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key
E
Encoding
F PS/2 25 and 30 w/Standard Key Encoding
G IBM 3xxx w/122 keyboard
H IBM 3xxx w/102 keyboard
I PS/55 5530T w/104 keyboard
J NEC 9801
K WYSE 30/30+ WY-30 Keyboard 83 Keys
WYSE 60/85/99 GT/150/160/285 Style IBM Enhanced PC, 520/520ES
L
Style IBM Enhanced PC FR
WYSE 55/65/65 ES/120/185/325 Style IBM Enhanced PC
WYSE 60/85/99 GT/150/160/285 ANSI Keyboard 105 Keys, 520/520 ES
M
ANSI Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI Keyboard 105 Keys
WYSE 60/85/99 GT/150/160/285 ASCII Kbd, 520/520 ES ASCII Kbd
N
WYSE 55/65/65 ES/120/185/325 ASCII Keyboard
WYSE 60/85/99 GT/150/160/285 ANSI W285 Keyboard 105 Keys, 520/
O
520 ES ANSI W285 Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI W285 Keyboard 105 Keys
P WYSE WINTERM 3320 SE
10 PowerScan® 7000BT SRI
IBM 3153
Q
IBM 316X, 3179/3180/319X/3270
R IBM 3151/3152-010, 347X/348X
S DIGITAL VT 220/320/330/340/350/382
T DIGITAL VT420
U DIGITAL VT 510/520 IBM ANSI Style Keyboard
V DIGITAL VT 510/520 IBM PC Style Keyboard
W SUN SPARC 5/10
X SUN 420/440, ITX
Reference the Product Reference Guide (PRG) for
more information about keyboard support.
NOTE
Keyboard
Wedge A
Getting Started
Keyboard
Wedge B
Keyboard
Wedge C
Keyboard
Wedge D
Keyboard
Wedge E
Keyboard
Wedge F
Keyboard
Wedge G
Quick Reference Guide 11
Keyboard
Wedge H
Keyboard
Wedge I
Keyboard
Wedge J
Keyboard
Wedge K
Keyboard
Wedge L
Keyboard
Wedge M
Keyboard
Wedge N
Keyboard
Wedge O
Keyboard
Wedge P
Keyboard
Wedge Q
Keyboard
Wedge R
12 PowerScan® 7000BT SRI
Keyboard
Wedge S
Keyboard
Wedge T
Keyboard
Wedge U
Keyboard
Wedge V
Keyboard
Wedge W
Getting Started
Keyboard
Wedge X
Resetting the Standard Product Defaults
If programming settings for your scanner are in an unknown condition,
factory settings can be restored by scanning the “Standard Product
Default Settings” bar code below. A listing of factory default settings is
available in the PRG. Settings can vary, depending upon the interface
type.
Standard Product Default Settings
Quick Reference Guide 13
How to Scan
When the trigger is pressed, the scanner projects a red, horizontal illuminating beam. This beam will remain on until the trigger is released, a bar
1
code is read, or until a time-out
If the surface being scanned is highly reflective
(e.g., laminated), it may be necessary to tilt the item
or the scanner slightly (15° to 18°) to prevent
NOTE
unwanted reflection.
period expires.
Linear Bar Codes —
beam over the bar code as shown in
To scan a linear bar code, center the illumination
Figure 6a. The scanner must “see”
across the width of all of the bars. Move the scanner further away from
the bar code to increase the scanning coverage area.
Stacked Bar Codes —
Stacked bar codes are read by holding in on the
trigger and moving the illumination beam in a smooth motion over the
bar code from top to bottom as shown in
Figure 6b. That motion should
be slow as well, since moving very fast will cause individual rows of the
stacked code to be overlooked, and will require extra sweeps to capture.
You will hear a series of ticks, followed by a final beep when the bar
code’s content has been completely decoded. You may need to sweep the
bar code several times in order to complete the read. Sweeps may be
made either from top-to-bottom or bottom-to-top.
1. Reference the Product Reference Guide (PRG) for more information about the aiming
beam time-out period.
14 PowerScan® 7000BT SRI
Figure 6. Scanning Bar Codes
Decrease...
Troubleshooting
a
...or Increase distance
from bar code to adjust
aiming beam width to
cross all bars.
b
Stacked
Sweep stacked bar codes
slowly and smoothly from
top to bottom (or bottom to top).
Troubleshooting
Troubleshoot your scanning system by performing the following checks:
Troubleshooting the RF System
For the RF system, ensure...
• the battery is charged. See
Maintenance" on page 7
"Battery Pack Charging and
.
• the battery is properly installed. See
page 1
Quick Reference Guide 15
.
"Installing the Battery Pack" on
• the scanner is linked to the desired Base Station. See "Linking the
Scanner to a Base Station" on page 5
.
• the scanner is within reasonable operating range of the Base Station, with no major obstructions between the radio units such as
thick walls or heavy machinery. (At the time of this writing, maximum scanner-to-Base Station range is specified at 100 meters.)
• the Base Station is powered-on. When the Base Station powers up,
both LEDs briefly flash. If both lights are bright and crisp, this is a
good indication of adequate power input from either Power Off
the Terminal (P.O.T.) or the optional AC Adapter (if used).
• the Base Station interface cable is securely attached to the host.
Consult your technical support manager or refer to your host system manual to identify the proper cable connection for the scanner. If necessary, verify interface cable function by using a knowngood interface cable.
Troubleshooting the Scanner
If the problem is specific to scanning, verify that...
• The scanner will automatically perform a set of self-tests whenever
you turn it on. Observe and note any special indications made by
the scanner (an unexpected pattern of flashes or beeps) during
power-up. If technical support is contacted regarding a problem,
they may request this information.
• Does the scanner power on? Does the illumination beam come on?
If no illumination beam, check that...
• the battery has been adequately charged.
• the battery is fully seated and its latch engaged.
• the trigger works.
• Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols...
• aren’t smeared, rough, scratched, or exhibiting voids.
• aren’t coated with frost or water droplets on the surface.
16 PowerScan® 7000BT SRI
Troubleshooting
• are enabled in the scanner. See the Product Reference Guide
(PRG) for more about configuring the scanner to read symbologies).
• Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still
have to press a key to enter it (the Enter/Return or Tab key, for
example).
You need to program a suffix which enables the scanner to output
the bar code data plus the key you need (such as a carriage return
“CR”) to enter the data into your application. Refer to the PRG
for further information.
• Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on the host screen:
• The scanner may not be programmed for the appropriate termi-
nal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the scanner with the correct interface
selection bar code. See the Product Reference Guide (PRG).
• The scanner may not be programmed to output your bar code
data properly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the scanner with the proper Data
Editing selections. Reference the PRG.
• The scanner won’t read your bar code at all.
• Scan the part number bar code on the back of this manual or
other known-good bar code samples. If the scanner reads sample
bar codes, check that your target bar code is readable.
• Verify that your bar code symbology is enabled. See the PRG.
• If you aren’t sure what programming options have been set in the
scanner, or if you want the factory default settings restored, go to
Resetting the Standard Product Defaults section of this manual
the
and scan the standard factory default settings bar code.
Quick Reference Guide 17
• The scanner sounds other than a standard “Good Read” beep fol-
1
lowed by an “Acknowledge
” beep when reading a bar code (indi-
cating the bar code has been read and properly transmitted).
• Verify the scanner is linked to and within range of its Base Station.
1. Typically, both of these beep indications are active in the scanner. To enable/disable these
indications, reference the PRG.
18 PowerScan® 7000BT SRI
PSC Inc. hereby declares that the equipment specified below has been tested and found
compliant to the following directives and standards.
EU Directives: 89/336/EEC EMC
73/23/EEC Low Voltage
Standards
Radio: FCC Part 15.247 and Part 2 (US)
RSS-210 (Canada)
ETS 300 328 (R&TTE directive) (Europe)
and others
EMC: FCC Part 15 Class B (US)
ICES-003 Class B (Canada)
EN 55022 Class B (Europe)
AS/NZS CISPR 22 [Class B] (Australia/New Zealand)
Product Safety: UL 60950-1 (US)
CSA 60950-00 (Canada)
EN 60950 (Europe)
EN 60825-1/A2 (Europe)
IEC 60950-1 (World)
IEC 60825-1 (World)
Li-Ion Battery Pack: UL 1642, UL 2054
United Nations 38.3
Immunity: EN55024 and EN301 489- Generic Immunity – ITE (Europe)
EN 61000-3-2 - Harmonic Current (EU)
EN 61000-3-3 - Voltage Flicker (EU)
Quality Systems: ISO 9001:2000
BS EN ISO 9001:2000
Power Supplies (optional equipment):
UL 60950 (120 VAC - US)
EN 60950 / IEC 60950 (230 VAC – Eu rope / World)
AS/NZ60950
Equipment Type: Barcode Scanning
Product:PowerScan
Serial Number Start Sequence: WXxxxxxx
Date Placed into EU Service: October 2006
Responsible Manufacturer: PSC Inc./PSC Scanning, Inc.
959 Terry St. Eugene, OR 97402 US
CUS
®
LISTED
NWGQ 2Z78
®
7000BT SRI with Base Station
Asia Pacific
Italy
PSC Hong Kong
Hong Kong
Telephone: [852]-2-584-6210
Fax: [852]-2-521-0291
Australia
PSC Asia Pacific Pty Ltd.
North Ryde, Australia
Telephone: [61] (2) 9870 3200
Fax: [61] (2) 9878 8688
France
PSC S.A.R.L.
LES ULIS Cedex, France
Telephone: [33].01.64.86.71.00
Fax: [33].01.64 46.72.44
PSC S.p.A.
Vimercate (MI), Italy
Telephone: [39] (0) 39/62903.1
Fax: [39] (0) 39/6859496
Japan
PSC Japan K.K.
Shinagawa, Tokyo, Japan
Telephone: 81 (0)3 3491 6761
Fax: 81 (0)3 3491 6656
Latin America
PSC S.A., INC.
Miami, Florida, USA
Telephone: (305) 591-3222
Fax: (305) 591-3007
Germany
PSC GmbH
Darmstadt, Germany
Telephone: 49 (0) 61 51/93 58-0
Fax: 49 (0) 61 51/93 58 58
PSC Inc.
959 Terry Street
Eugene, OR 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
United Kingdom
PSC Bar Code Ltd.
Watford, England
Telephone: 44 (0) 1923 809500
Fax: 44 (0) 1923 809 505
www.psc.com
©2006 PSC INC. R44-2586 (Rev. X3) 10/06
Loading...