ProScan PS27410YX1AX User Manual
TV
USER'S
MANUAL
i!iiii_
S
IMPORTANT IN FORMATION
WARNING
To reduce the risk of fire or
shock hazard, do not expose
this TV to rain or moisture.
To reduce the risk of electric shock, do not remove
cover (or back). No user serviceable parts inside. Refer
servicing to qualified service personnel.
This symbol indicates
"dangerous voltage" inside
the product that presents a
risk of electric shock or
personal injury.
_1_ This symbol indicates
important instructions
accompanying the product.
Caution: To reduce the risk of electric shock, match
wide blade of plug to wide slot, fully insert.
Attention: Pour 6viter les chocs 6Iectriques, introduire
la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusq0 au fond.
Refer to the identification/rating label located on the
back panel of your product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifications to
this equipment may void the user's authority to operate it.
If fixed (non-moving) images are left on the screen for long
periods, they may be permanently imprinted on the screen.
Such images include network Iogos, phone numbers, and video
games. This damage is not covered by your warranty.
Extended viewing of channels displaying these images should
be avoided.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the
Canadian Electrical Code, Part 1) which provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building as close to the point
of cable entry as practical.
PRODUCT REGISTRATION
Please fill out the product registration car{] and return it immediatety_ Returning the card allows us to contact you if needed_
Keep your sa[es receipt to obtain warranty parts and service an(] for proof of pulchase. Attach it hele and record timeserial and model numbers in case
you need them. The numbers are located on the back of the television.
Mode] No,
Serial No_
Pulchase Date:
Dea[el/Addl ess/Phone:
VCR Plus+, C3,PlusCode, GUIDE Plus+, and GUIDE Plus+ Gold are trademarks of Gemstar Devek)pment Corporation.
The GUIDE Plus+ Gold system is manufactured under license from Index Systems Inc.
TABLE OF CONTENTS
Setup and Connections ..................................................... 3
Step 1: Unpack the TV .................................................. 4
Step 2: Connect Your TV ............................................... 4
TV Only (PIP Not Available) ....................................... 4
The Basic Connection (PIP Not Available) .................. 5
Advanced Connections .............................................. 6
Back of the TV ............................................................ 6
Sample Connections ................................................... 7
Step 3: Connect the IR Controller ................................ 9
Step 4: Plug in the TV ................................................. 10
Step 5: Place Batteries in the Remote ....................... 10
Step 6: Turn On the TV ............................................... 10
On-Screen Program Guide ....................................... 10
Step 7: Program the TV .............................................. 10
Interactive Setup .............................................................. 11
Using Point and Select ............................................... 12
Entering Setup ............................................................ 12
Selecting a Language ................................................. 13
Auto Channel Search .................................................. 13
The GUIDE Plus+ Gold System .................................. 14
Setting the Time ............................................................. 16
Setting the VCR1 Channel (auto tuning) ......................... 17
Setting the VCR2 Channel (auto tuning) ................... 17
Setting the DVD Channel (auto tuning) ..................... 18
Setting the SAT/CABLE Channel (auto tuning) ......... 19
Labeling the Channels ................................................ 20
Using the Remote ............................................................ 21
Remote Buttons .......................................................... 22
Using the WHO-INPUT Button ................................... 23
Programming the Remote .......................................... 24
Using the Remote to Control a Device ..................... 25
Modes of Operation .................................................... 25
Front Panel .................................................................. 25
Codes ........................................................................... 26
1
TABLE OF CONTENTS
Using the Menu System ...................................................... 27
Menus and Control Panels ......................................... 28
Sliders ...................................................................... 29
Numeric Entry .......................................................... 29
Audio Menu ................................................................. 30
Using the Remote to Select an Audio Processor ..... 31
Picture Quality Menu .................................................. 32
Screen Menu ............................................................... 33
Using Closed Captioning .......................................... 34
Channel Menu ............................................................. 35
Time Menu ................................................................... 36
Other Menus ................................................................ 36
Features and Controls ..................................................... 37
GUIDE Plus+ Gold Menu .............................................. 38
About the GUIDE Plus+ Gold System ............................ 38
Getting In & Out of the GUIDE Plus+ Gold System .. 39
Downloading Data ................................................... 39
Channel Mapping ..................................................... 39
The Different GUIDE Plus+ Gold System Menus ...... 39
PIP (Picture-in-Picture) Operation .............................. 45
Channel Marker ........................................................... 46
Parental Controls and V-Chip ......................................... 47
The Ratings Limits Screen ......................................... 48
V-Chip TV Rating Limit ............................................. 48
V-Chip Movie Rating Limit ....................................... 52
V-Chip Unrated Program Block ................................ 53
Channel Block .......................................................... 53
Front Panel Block ..................................................... 53
Lock/Unlock Parental Controls ................................. 53
Troubleshooting ............................................................... 54
Warranty ........................................................................... 56
Index .................................................................................. 61
2
SETUP AND CONNECTIONS
GETTING STARTED
This manual is designed to get you started quick]x
The first five sections of the manual show you how
to get yourTV set up and connected, run the
Interactive Setup, program the remote, and use all of
the menus, features, and controls of yourTXZ
The reference section in the back of the book
contains troubleshooting tips, care and cleanin
instructions, accessory ordering JnformatJoB
warranty
Well... if yourTV's
/
y/'
i SETUP AND
CONNECTIONS
%
2 INTERACTIVE SETUP
V
3 USING THE REMOTE
4 M
V
5 FEATURES
6 REFERENCE
3
SETUP AND CONNECTIONS
STEPI: UNPACK THETV
Make sure to locate the remote control.
STEP2: CONNECTYOURTV
There are three types of connections outlined in this section:
TV Only: If you're only going to connect the TV to
your home antenna or cable system.
The Basic Connection: If you're going to connect the TV to a
VCR or satellite receiver.
Advanced Connections:
If you're going to make multiple
connections, hooking up the TV to a
VCR and a satellite receiver.
Cable information and illustrations are given for each type of
connection. Once you have completed your desired connection you
may skip forward to Step 3.
TV ONLY(PIP NoT AVAILABLE)
This is a basic connection from an antenna or cable system to your TV.
Connect the cable into the Cable/Antenna jack asshown.
CABLES
You will use the following cable to make your connection:
Coaxial Cable: These cables carry audio
and vide{} signals to the TV from an
antenna, cable, or cable box.
r
Important Stand Information
CAUTION: Choose the k}cation for your
TV carefully. Take precautions that the
stand or other furniture on which the TV
is placed is properly located (see
Important Safeguardssheet) and of
adequate size and strength to prevent the
TV frorn accidentally being tipped over,
pushed off, or pulled off. This could
cause damage to the TV and/or personal
_injury. #
Before You Connect
Protect against power surges:
• Connect all cornponents before
plugging any power cords into the wall
outlet.
• Turn off the TV and/or cornponent
before connecting or disconnecting
any cables.
• Make sure all antennas and cables are
properly grounded. Refer to the
Irnportant Safeguards sheet packed
with your TV.
CABLE, CABLE BOX, OR ANTENNA
TV
g
Once you have completed this connection you may go to Step 3.
q • •
his Connection Will Not Allow
You to Use Your PIP
Your TV is equipped with a single tuner,
which means you must connect with a
second video source using Audio/Video
Cables to view PIR This TV Only
connection will not enable you to use
your PIP,but will get your TV up and
running quickly.
Refer to Advanced Connections for
connecting Audio/Video cables to your
VCR or other vide{} component.
4
SETUP AND CONNECTIONS
THE BASIC CONNECTION (PIP NOT AVAILABLE)
The basic connection below (TV and VCR) is the most common
connection and is therefore used to illustrate a single component
connection with your TV. For better sound and picture quality and
multiple component connection information refer to the next section,
Advanced Connections.
CABLES
You will use the following type of cable to make your connection:
Coaxial Cables: In this connection, two Coaxial
Cables are used: one connects from an antenna,
cable, or cable box to the VCR, and one connects
from the VCR to the TV. These cables carry both
audio and video signals.
CABLE, CABLE BOX, OR ANTENNA
VCR I
iN FROM ANT CH3 I
ou_ _ c._
I
VIDEO AUDIO
TV
V_DEO R AUD[OL / MONO
[_ Q
R
vcR [o °°'
CABLE/
CONmOL (_ 0 ANTENNA
_ S VIDEO
r
This Connection Will Not Allow
You to Use PIP
Your TV is equipped with a single tuner,
which means you must connect with a
second video source using Audio/Video
Cables to view PIP.This Basic
Connection will not enable you to use
your PIP,but will get your TV up and
running quickly.
Refer to Advanced Connections for
connecting Audio/Video cables to your
VCR or other vide() component.
How ToVIEw THEVCR
To watch the VCR in this connection tune TV to
Channel 3 or 4.
Later, in the Interactive Setup section you will
program the TV to automatically tune to Channel 3
or 4 when you turn on the VCR.
Once you have completed this connection you may skip to Step 3, "Connect the IRController."
5
SETUP AND CONNECTIONS
ADVANCED CONNECTIONS
Advanced connections give you better sound and vide() by separating
the audio and vide() signals and enabling you to connect multiple
components.
This section describes the types of inputs available on the back of your
TV and suggests ways you can use them for optirnurn performance.
BACK OF THETV
The diagrarn below describes each of the back panel jacks. When
connecting A/V cables, be sure to connect corresponding OUTPUTS
and INPUTS (Vide() to Vide(), Right Audio to Right Audio, etc.).
Once you have made your connections,
you will need to program the TV to tune
to the correct Video input channel in
order to see and hear audio and video
from a component such as a VCR or
DVD player. You will program this later
in the Interactive Setup.
J
VIDEO and Audio Inputs
Connect any one of the following cornponents
• VCR • Internet Access Device
• Laserdisc Player • DVD Player
• Satellite Receiver
To view the component connected to VIDEO,
use the WHO • IN PUT button on the remote.
\
_ VIDEO
[e
VCR
CONTROL
[_- _ _OUT
S V_ID£O
VCR Control
T
Connect the GUIDE
Plus+ Gold systern IR
controller for one-button
recording and channel
tuning frorn the GUIDE
Plus+ Gold system.
S-Video
This optional
connection
can be used
for better
video quality
_.picture.
/
1
Audio Outputs
Connect to an audio re'ceiver or
arnplifier for variable controlled
or fixed level stere()output.
/
e CABLE/
ANTENNA
I Cable/Antenna
Takes the signal input frorn a cable,
cable box, or an off-air antenna. Can
also be used for basic component
connections.
6
SETUP AND CONNECTIONS
SAMPLE CONNECTIONS
The following are sample connection scenarios you may encounter
when connecting components to your TV. Note: components that offer
an S-Video connection, such as DVDs, VCRs or satellite receivers,
must match their S-Video connection with their audio INPUT
connection.
CABLES
You will use the following types of cables to make your connection:
Coaxial Cables: Carries the signal from the
antenna or cable directly to the television or
through a cable box, as needed by your cable
system.
Audio/Video Cables: Carries audit} and video
from a component to the TV.
S-Video Cable: Carries video from an S-Video
capable component which provides best
picture quality.
TV AND STEREoVCR
Compared to the Basic Connection, using Audio/Video and
S-Video (if available) cables will enhance the sound and picture
quality from a cornponent.
Cautions:
Position cablesto avoid audio hum or
interference
• Insert all cables firmly into jacks.
• Place the audio/video cables to the
sides of the TV's back panel instead of
straight down the middle.
• Try not to coil any twin-lead cables
and keep them away from the audit)/
video cables.
Protect your componentsfrom
overheating
• Do not block v_'ntilation holes in any
of the components. Arrange the
components so that air can circulate
freely.
• Do not stack components.
• Allow adequate ventilation when
placing your components in a stand.
• Place an amplifier on the top shelf of
the stand so heated air rising frorn it
will not flow around other
components.
CABLE, CABLE BOX, OR ANTENNA
VCRI
o To
[ _IDEO R L
TV
"_wo.o _ A°°_°?Mo.o
R
CONTItOL _
_ S VIDEO
INFROMo ANT CH41CH3[I
ou
How TOVIEwYouP, VCR
Towatch the VCR in this connection, press TV to put the
rernote control into TV mode, then press WHO.INPUT to
toggle to the video (VID) inputs.
In the Interactive Setup section you can program the TV
to automatically tune to the VID input channel when you
turn on the VCR.
Most Audio/Video cables are combined
into one cable with three heads on each
end.
We show individual
cables in these wd_o{01low)
sample Right Audio {red)
connections. Either _
may be used, but _)
you must be sure to
connect Video to Video,
Right to Right and Left to Left.
7
SETUP AND CONNECTIONS
TV,VCR AND SATELLITE RECEIVER
CABLE, CABLE BOX, OR ANTENNA
SATELLITE RECEIVER
VCR 1
TV
SATELLITE SIGNAL
How ToVIEwYOUR COMPONENTS
To watch the satellite r_ceiver in this
connection, press TV to put the r_Tnote
control into TV mode, then press
WHO-INPUT to scroll through the video
input channels until you tune to VID (or
SVID) input.
To watch the VCR in this connection, enter 03
to tune to the VCR channel.
In the Interactive Setup you can program the
TV to automatically tune to the correct input
channel when you turn on your component.
8
SETUP AND CONNECTIONS
STEP3: CONNECT THE IR CONTROLLER
The IR (Infrared) Controller enables the GUIDE Plus+ Gold system to
control your VCR and cable box (if necessary) so you can tune to
television channels and even start recording a program from the
GUIDE Plus+ Gold system.
After you have affixed the ends of the controller to the necessary
component (VCR, or Cable box), use the on-screen interactive setup
routine for the GUIDE Plus+ Gold system to test the connected
components.
ATTACHING THE IR CONTROLLER
The IR Controller is used to send commands to yourVCR
and/or cable box
Some components have a labeled infrared re,mote sensor,and others
do not. If your component is labeled, affix the IR controller directly
over the sensor. If the IR location is not labeled on your component,
you need to useto use the component's remote control to locate the
sensor.
2.
Hold the component's remote control (not the remote that came
with your TV) so that it is touching the front of the component.
Slowly move the remote over the front of the component while
pressing the remote power button on and off. (Be sure,to press and
release the power button each time you move the remote. Holding
the button may not work.)
3.
4.
I © ii ii
When the component turns off or on, you've located the sensor.
Affix the controller's node directly to the remote sensor.
ii ......I
' []1
Attach to the VCR ÷÷÷.°°°7*
'" Attach to the cable box If you do not
have a cable box, just leave it unattached,
Connect to the TV
Tip
You may want to use a piece of clear
plastic tape to temporarily affix the
controller's node until you have
completed the interactive setup. That way
you can easily move it if you have not
placed it exactly over the sensor.
9
SETUP AND CONNECTIONS
STEP4: PLUG IN THETV
Plug the end into the wall outlet, matching the wide blade of the plug
with the wide slot in the outlet. Be sure to insert the plug completely.
STEP S: PLACE BATTERIES IN THE REMOTE
Remove the battery compartment cover from the back of the
remote.
Insert fresh batteries. Make sure that the polarities (+ and -) are
aligned correctly.
• Replace the cover.
STEP &TURN ON THETV
PressTV on the remote, or press POWER on the TV itself.
Pressing the TV button not only turns on the TV, but puts the remote
into TV mode, so that the buttons on the remote will control TV
functions.
ON-SCREEN PROGRAM GUIDE
The TV is designed to bring up the GUIDE Plus+ Gold on-scr_'en
program guide when you use the TV button on the remote to turn on
the TV (after you have set up the GUIDE Plus+ Gold system). For more
information on setting up the GUIDE Plus+ Gold system, see the next
section, Interactive Setup.
To GET OUT OF THE GUIDE PLUS+ GOLD SYSTEM:
• Pr_'ssOK to exit the GUIDE Plus+ Gold system and tune to the
highlighted channel.
• Pr_'ssGUIDE to exit the GUIDE Plus+ Gold system and tune to the
channel displayed in the View window.
• PressCLEAR to exit the GUIDE Plus+ Gold system and go to the
last channel you were watching.
STEP 7: PROGRAM THETV
Proceed to the next section, Interactive Setup. The interactive setup
routine walks you through the steps needed to fully configure the TV.
The first steps ask you to select your preferr_,d language for the menu
system and to begin the auto channel search, which puts available
cable TV or antenna signals into the TV's memory.
10
INTERACTIVE SETUP
THERE'S AN ON-SCREEN SETUP ROUTINE
The interactive setup routine helps you through the steps
needed to configure theTV and set up the GUDE Plus+
Gold menu system:
• Select a menu language
• Search for available channels
Set up the GUIDE Plus+ Gold system
Set the time
Set the VCR I channel
Set the VCR2 channel
Set the DVD channel
Set the SAT/CABLE channel
• Make the channel list and labels
+
1
3
5
i_ ¸¸¸¸ .
SETUP AND
CONNECTIONS
%
<
INTERACTIVE SETUP
USING THE REMOTE
FEATURES AN
CONTROLS
REFERENCE
u
s+i!i¸
%
%
11
INTERACTIVE SETUP
USING POINT AND SELECT
You only need to know one rule when using the remote to access on-
screen menus and control panels: point and select. The point and
select method has two steps.
I. Point to a menu item using the MOVE arrows on the remote.
To point up or down, press the up or down arrows. To point left
or right, press the left or right arrows.
2. Select a menu item by pressing MENU or OK.
Selecting an item tells the TV's menu system to go ahead and
make the change or go to a place you have indicated.
ENTERING SETUP
The first screen of the Interactive Setup appears automatically when
you turn on your TV for the first time or after a power outage.
1. Press MENU to begin setup or CLEAR to exit.
<8 C>
Point and Select
buttons
You can also access the Interactive Setup through the Main menu:
1. Press MENU to bring up the Main menu.
2.
Point to Setup and press MENU or OK. The first Setup screen
comes up, asking you to confirm that you want to begin.
You can also select a menu item by
entering the item number with the
number buttons on the remote.
PressCLEARat any time to remove all
displays from the screen and return to TV
viewing.
Many VCR user manuals refer to a
PROGRAM button. The MENU button on
this remote works as a PROGRAM button
in VCR mode. Other manuals may refer
to a SELECT button. The OK button on
this remote works as a SELECT button.
12
INTERACTIVE SETUP
3. Point to BG_in setup now and press MENU or OK.
SELECTING A LANGUAGE
The first part of the setup routine asks you to select your preferred
language for the menu system.
1. Point to your preferred language for the menu system.
2. PressMENU or OK to select that language.
AUTO CHANNEL SEARCH
The next part of the setup routine asks you if you want the TV to search
for all channels viewable through your antenna or cable TV system.
This is sometimes called "auto programming."
1.
PressMENU or OK to tell the TV to begin searching for channels.
The display gives you a progress report and tells you when it has
finished.
If you skip Auto Channel Search now, I
you can access it later through the
J
Channel menu. See Using the Menus for
more details.
13
INTERACTIVE SETUP
THEGUIDE Plus+ GOLD SYSTEM
The next step lets you set up the GUIDE Plus+ Gold system to display your local
program listings, and control your cable box and VCR.
You can either press MENU or OK to bring up the GUIDE Plus+ Gold initial
menu or point to Skip this St_p to move to the next step in the Interactive Setup.
, GUIDE PLus+
You can set upthe GUIDE
Plus+ Gold system during
Interactive Setup or by
selecting the GUIDE Plus+
Menu from the Main Menu.
SETTING UP THE GUIDE Plus+ GOLD SYSTEM
To complete GUIDE Plus+ Gold setup, the GUIDE Plus+ Gold IR controllers must be connected to your cable
box and VCR if you have them. Refer to the Setup and Connections sectk)n for additional information.
Select your Country and enter your
ZIP or Postal code.
The next series of screens asksyou
about your cable TV setup. If you
have a cable box, you need to set the
GUIDE Plus+ Gold system to control
it. Otherwise, it may not be able to
locate and download program
information.
Tune your cable box to Channel 2
and then select the brand of your
cable box from the choices available.
The system then searches for the
correct code to control your cable
box. When your cable box switches
to channel 9 it has located the correct
code.
14
INTERACTIVE SETUP
Select YESif the cable box changed to channel 9, or NO if it did not. If you select NO, the system will
try another code.
If the GUIDE Plus+ Gold system cannot recognize either your cable box or VCR after several tries, a
scr_'en stating "Cable Box (VCR) test failed...Please consult your manual and try again" appears. You
have a choice to either Try Again or Skip Cable Box Setup. If you get this message, you should also:
• Double check the brand of your cable box or VCR, and try entering it again.
• Check to make sure the IRcontrollers are positioned correctly.
If you choose to skip the cable box (or VCR) setup some features of the guide may not be available until
you successfully complete this procedure.
Once the correct model of cable box (or
VCR) has been identified, you need to set
the cable box's output channel. Enter the
channel you use to view channels
through your cable box--usually 3 or 4.
Consult your cable box's instruction book
or your cable company if you are not
sure. Choose Oto use VIDEO INPUT.
Select YESif you have a VCR, or NO if not.
(Answering NO automatically skips forward
to the end of GUIDE Plus+ Gold setup.)
Tune your VCR to channel 2 and turn it off.
Enter the brand of your VCR.
When the GUIDE Plus+ system correctly
identifies the correct code for your VCR,
the VCR's tuner changes to channel 9.
Select YESif the VCR automatically changed
to channel 9, or NO if it did not.
If you select NO, the system will try another
code.
The last screen comes up when you've
successfully finished the GUIDE Plus+ Gold
setup.
Remember:
• Leave your cable box turned ON to download program information.
• Leave your VCR turned OFF to record programs.
PressOK to leave the GUIDE Plus+ Gold system setup and either return to the TV's Interactive Setup or the Main Menu.
For more information about the GUIDE Plus+ Gold system, see the section Features and Controls.
15
INTERACTIVE SETUP
SETTING THETIME
The next step in the Interactive Setup letsyou set the time of day. If
your GUIDE Plus+ Gold system has not completed its first download,
you need to set the time. Once the system has completed its first
download, it setsthe time for you automatically.
Set time
1. PressMENU or OK to bring up the SetTime control panel.
2.
Use the left and right arrows to point to the hour and minutes
spaces. Use the digits to enter the numbers and the up and down
arrows to change from AM to PM.
3. Press MENU or OK to continue.
16
INTERACTIVE SETUP
SETTING THE VCRI CHANNEL (AUTO TUNING)
The next step lets you setthe VCR1 channel. When you set the VCR1
channel, you're telling the TV what channel to tune to when you press
the VCR1 button on the remote. This is called auto tuning.
Indicate which input you used to connect the VCR. If you don't have a
VCR1 component connected to the TV, skip this step or select Not
Connected from the VCR1 Channel choice list. (For more, see Auto
Tuning in the Using the Menus section.)
1. PressMENU or OK to bring up the VCR1 choice list.
2. Point to the choice that matches the way you have your VCR
connected to the TV.
3. Press MENU or OK to continue.
SETTING THEVCR2 CHANNEL (AUTO TUNING)
The next step lets you setthe VCR2 channel. When you set the VCR2
channel, you're telling the TV what channel to tune to when you press
the VCR2 button on the remote.
Indicate which input you used to connect a second VCR. If you don't
have a second VCR component connected to the TV, skip this step or
select Not Connected from the VCR2 Channel choice list. (For more,
seeAuto Tuning in the Using the Menus section.)
17
INTERACTIVE SETUP
1. PressMENU or OK to bring up the VCR2 choice list.
2. Point to the choice that matches the way you have your second
VCR connected to the TV.
3. Press MENU or OK to continue.
SETTING THE DVD CHANNEL (AUTO TUNING)
The next step lets you set the DVD channel. When you set the DVD
channel, you're telling the TV what channel to tune to when you press
the DVD button oil the remote.
Indicate which input you used to connect a DVD player. If you don't
have a DVD player connected to the TV, skip this step or select Not
Connected from the DVD Channel choice list. (For more, see Auto
Tuning in the Using the Menus section.)
1. PressMENU or OK to bring up the DVD choice list.
18
Loading...