ProScan 55LED55SA User Manual

Important to user

NOTE:
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority.

NOTE:
This equipment has been tested and found to comply with the limits for a class B digital

Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio Communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and the receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Important safety precautions

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of un-insulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric to persons.

The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)

instructions inthe literature

accompanying the appliance,

Important safety instructions

CAUTION

TO REDUCE THE RISK OF AN ELECTRIC

SHOCK, DO NOT REMOVE THE COVER (OR

BACK). THERE ARE NO USER SERVICEABLE

PARTS INSIDE. FOR ANY REQUIRED

SERVICING, PLEASE CONTACT QUALIFIED

SERVICE PERSONNEL.

CAUTION:
USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION:

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do

not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions.

Important safety instructions

1. Read these instructions

2. Keep these instructions

3. Heed all warnings

4. Follow all instructions

5. Do not use this apparatus near water

6. Clean only with dry cloth

7. Do not block any ventilation openings

8. Do not install near any heat sources

9. Do not defeat the safety purpose of the polarized or grounding-type plug

10. Protect the power cord from being damaged particularly at plugs, convenience receptacles, and at
points in which they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

2

Important safety precautions

Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as when the
power-supply cord or plug is damaged, when liquid has been
spilled or when objects have fallen into the apparatus, or when
the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.

POWER SOURCE: This TV should be operated only from the type of S3126A
power source indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or local power company. For TVs
intended to operate from battery power, or other sources, refer to the operating
instructions.

POWER CORD PROTECTION: Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
OUTDOOR ANTENNA GROUNDING : If an outside antenna or cable system is
connected to the TV, be sure the antenna or cable system is
grounded to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI/NFPA NO.70, provides information
with respect to proper grounding of the
mast and supporting structure, grounding
of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna discharge unit, connection to
grounding electrodes, and requirements for

the grounding electrode. (Fig.A) S2898A - _ POWERSERVICEGROUNDING

ELECTRODESYSTEM

LIGHTNING: For added protection for this TV receiver during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage to the
TV due to lightning and power line surges.
POWER LINES: An outside antenna system should not be located in the vicinity of
overhead power lines, or other electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with
them might be fatal.

FIGURE A

EXAMPLE OF ANTENNA GROUNDINGAS PEF

ANTENNA LEAD

NATIONAL ELECTRICAL CODE IN WIRE

C LAIVIP "-/_, E

3

Important safety precautions

20. OVERLOADING: Do not overload wall outlets and extension cords as this can result
in a risk of fire or electric shock.

21. OUTDOOR USE: Do not install this TV outdoor. If the TV is exposed to rain, it may
result in a fire or an electric shock. If the TV is exposed to direct sunlight, the TV may
heat up and cause damage to the TV.

22. VEHICLE: Do not install the TV in a vehicle. Bumping of the vehicle may cause the
TV to fall down and cause injury.

23. SHIP AND VESSEL: Do not install this TV in a ship or vessel. If the TV is exposed to
seawater, it may cause a fire or damage the TV.

24. OBJECT AND LIQUID ENTRY: Never push objects of any kind into this TV through
openings as they may touch dangerous voltage points or short out parts that could
result in fire or electric shock. Never spill liquid of any kind into the TV.

25. SERVICING: Do not attempt to service this TV yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.

26. REPLACEMENT PARTS: When replacement parts are required, be sure that the
service technician uses replacement parts with the same characteristics as the
original parts specified by the manufacturer. Unauthorized substitutions may result in
fire, electric shock, injury to persons or other hazards.

27. SAFETY CHECK: Upon completion of any service or repairs to this TV, ask the
service technician to perform routine safety checks to determine that the TV is in
proper operating condition.

28. The apparatus should not be exposed to any dripping or splashing, and no objects
filled with liquids (such as a vase) should be placed on the apparatus.

29. WARNING: Plug the power cord into a power outlet where access to the power cord
connector is readily accessible, in case if the power needs to be immediately
disconnected.

30. ATTENTION: This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

a). Disposal of packaging:The packaging of this product is intended to be recycled. Apply

to the local authorities for correct disposal.

b). Disposal of batteries: The batteries supplied do not contain the heavy metals mercury

and cadmium. Please check on how to dispose exhausted batteries according to local
regulations.

c). Note Specifications and information are subject to change without notice. If you need

further assistance, please call the customer support service in your country.

31 .POWER=CORD INSERT CHECK:When connecting the power cord to the connector of the

TV, make sure the power cord is fully inserted in the place. Bad contact may cause high

temperature of the connector and the risk of fire or other damages.

Important Safety Precautions

To secure TV to stand or Wall, use hardware listed below (Not Supplied)

1. Attach the wall anchor on the stand.

2. Tie the ropes or chains with TV pedestal screws.
Ropes or chains should be secure tightly.

3. Fasten the anchor bolts into top wall-mount holes.

4. Attach the wall anchors on the wall strong enough to support the weight of the TV. (Attach to the

Wall Stud).

5. Make sure to connect anchor bolts to wall anchors.

• Anchor bolt - M6 x 10mm (42"and 47") or M6x 16mm(55")

6. Check that all connections are properly secured. Periodically check for any sign of fatigue or
failure. If you have any doubt about the security of your connections, contact a professional

installer.

5

Table of Contents

1.important to user ...................................................................................... 1

2.Important safety precautions .................................................................... 2

Safeguards ....................................................................................... 2

Safety Strap ...................................................................................... 5

3.Table of Contents ..................................................................................... 6

4.Setting Up................................................................................................. 7

Installing the Stand ...................................................................... 7

Wall mount specifications ...................................................................... 7

Wall mount ......................................................................................... 8

TV Front ........................................................................................... 10

TV Rear ............................................................................................ 11

Connect to other devices ................................................................. 12

5.Using the Remote Control ....................................................................... 15

Installing the remote control batteries ............................................... 15

Learning about the Remote Control Panel ....................................... 16

Quick starts ...................................................................................... 17

6.Changing the TV Settings ....................................................................... 19

Using the TV Menu .......................................................................... 19

Using the Video Menu ..................................................................... 20

Using the Audio Menu ..................................................................... 22

Using the Setup menu ..................................................................... 23

Using the Parental menu ................................................................. 26

7.Appendix ................................................................................................. 29

Trouble shooting .............................................................................. 29

Specifications ................................................................................... 30

6

Setting Up

Installing the Stand

@

1. Lay a cloth or another soft material on a flat surface to avoid damage to the LCD screen.

2. Put the TV back upward and the LCD screen downward and keep it flat on the table-board.

3. Take out the stand and insert the stand into the installing slot in the lower part of the TV, then put the
stand to relevant position of the TV set until all the holes match each other completely.

4. Fasten the stand and the TV set together with the 4 screws provided. Erect the TV set, and put it on
the proper position for watching.

Note:

The above figures are for reference only, please refer to the actual units to determine the appearances.

Every hole of the stand must be fastened with screws!

Wall mount specifications

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building
materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and
result in severe personal injury.

• Dimensions for wall mount kits and wall-mount screws pattern please refer specifications table.
Do not use screws longer than the standard dimension, as they may cause damage to the inside of

the TV set.

• For wall mounts that do not comply with the VESA standard screw specifications, the length of the

screws may differ depending on their specifications.

• Do not use screws that do not comply with the VESA standard screw specifications.

• Do not fasten the screws too strongly, this may damage the product or cause the product to fall,

leading to personal injury.

• Proscan is not liable for product damage or personal injury when a non-VESA or non-specified wall

mount is used or the consumer fails to follow the product installation instructions.

• Do not exceed 15 degrees tilt when mounting this TV.

7

Wallomounting Bracket Installation

42LED55SA 47LED55SA 55LED55SA

Unit Dimension(Unit:mm) 200 x 200 200 x 200 400 x 400

Screw Diameter M6 M6 M8

Screw Length(Unit:mm) 25 25 25

NOTE: Wall mount bracket is not included with TV and mounting of wall mount bracket to wall
may vary depending on brand and size of bracket. Customer should consult bracket mounting

instructions that came with wall mount for specific information on how to mount bracket to wall.

Removing TV Stand

1. Cover the surface of the table with soft cloth to avoid damage to LCD panel.

2. Lay the TV on a plane table which could bear a weight enough.

3. Remove the 4 bolts fixing the stand and remove the stand from TV.

Before reading the installing instruction, please notice:

A,

The wall mount is not contained in the accessories sold with television. We only provide the installing
specifications but not the wall mount itself. If you need the mount, please consult with the local dealer
for the assorted fitting parts.

B. We strongly suggest to set the wall mount with equipments of specification we ordered, if not,

inappropriate installing may cause damage to both the device and yourself.

8

Setting Up

When Installing the TV Against a Wall or Enclosed Area

Make sure that your TV has adequate air circulation. Allow enough space around

the TV as shown below. Avoid operating the TV at temperatures below Inadequate air 45° F (5°C)

Instand with stand

12 inches

4 inches

2.375 inches

6cm

... __ __ !U-L_d

Leave at least this much space ar the set.

Install on the wall 12inches

4 inches

10cr'n _

4 inches

Leave at least this much

space around the set.

Never install the TV set as follows:

Air circulation is blocked.

wall

Inadequate air circulation can lead to overheating of the TV and may cause damage to your TV or cause a

fire.

9

Setting Up

TV Front

Note:Touch the silk print area according to the need, the TV will response correctly.

No. Component Component Description

Blue light indicates standby mode. Flashing led shows the

1 POWER indicator

unit is powering on. The light is off when TV is turned on.
2 Remote sensor Receives signals from the remote control. Do not block.
3 Standby button Press to turn your TV on or off(Standby mode)

4 CH _' Press to go to the previous channel.

5 CH A Press to go to the next channel.
6 VOLT Press to decrease the volume.

7 VOLA Press to increase the volume.
8 input Press to select the signal source for your TV.

9 MENU Press to activate the on-screen display (OSD).

10

Setting Up

TV Rear

f COMPONENT2 -1

@Y-- @ PB-- _t PR-- (_) L-- @ R SERVICE

VIDEO

I AV2 [ j COAXIAL 0 _ HDMI 4

L

The cable tie is only used for the power cord.

Note: The appearance of 42LED55SA, 47LED55SA and 55LED55SA are similar, the picture above is

for reference only.

11

Setting Up

Warning: Before connecting the TV to any other electronic device, unplug the TV and electronic

device AC cords from the AC input.
Note: Not all following terminals are included on your TV. The actual one refer to "TV Rear".

1. Connect to broadcast antenna or the cable TV
To have an optimal picture quality, it is strongly recommended to have an external antenna or a cable TV.

Note:

- It is recommended that coaxial cable (750) be used to eliminate the interference caused by the

mismatched impedance.

- The antenna cable should not be bound together with the power cord.

- When using the cable TV, please insert the plug of the coaxial cable (75 O) directly into the antenna

A. E..ASOO.E COA.,A OAO .,7.O

ANT

outlet.

Adaptor (not suppl_

the screw

TWIN-LEAD FEEDER
(3000)

The signal comes from:

An outdoor antenna
An indoor antenna

CATV net

2.Insert the feeder in 3.Tighten the screw

2. Connect to AV devices

- Connect a Video RCA cable to an appropriate external A/V device such as a VCR, DVD or Camcorder.

- Connect RCA audio cables to "R -AUDIO - L" on your set and the other ends to corresponding audio
out connectors on the A/V device.

LU

= 1::3

>

Audio R

Audio L

Video

VCD, DVD, set-top boxes, etc.

12

Setting Up

3. Connecting Component Devices (DVD, DVR (digital video recorder), Blu-Ray) Component video(Y, Pb,
Pr)transmits video as separate Y, Pb, Pr signals. Use this connection for high-definition video signals

from a DVD or other equipment.

- Connect Component video and audio cables to Component inputs ("PR/CR", "PB/CB", "Y") of your set
and the other ends to corresponding component video out connectors on the PVR or DVD.

- The "Y, PB/CB and PR/CR" connectors on your component devices ((DVD, DVR (digital video recorder),

Blu-Ray) are sometimes labeled Y, B-Y and R-Y or Y, CB and CR. (Colors for inputs and cables must

correspond on both devices.)

DVD With Component jacks

4. Connect to devices with HDMI interface
HDMI: High Definition Multimedia Interface

HDMI transmits an all-digital signal and is the recommended choice for playback from a digital DVD or
DVR. No sound connection is needed for HDMI to HDMI connection.

- HDMI cable connected to the HDMI connector on the TV.

The equipment with HDMI
output jack ( such as DVD
players, set-top boxes, etc.).

13

Setting Up

5. Connect to PC

- Connect the D- Sub cable to "VGA" on the side of your set and the other end to the
Video Card of your computer.

- Connect the stereo audio cable to "PC AUDIO "on the side of your set and the other
end to "Audio Out" of the sound card on your computer.

Note: For some sets "PC AUDIO" share with component.

z

o

_®

<

Computer

6. Connect to headphone

- Connect the headphone jack of the TV set.
The volume of the headphone is automatically adjusted with the main volume of the

TV set.

o

n

,,<,

z

Headphone

14

Using the remote Control

Installing the remote control batteries

1. Open the battery cover on the back of the remote control.

2. Install two AAA size(1.5V) batteries. Match the "+" and "-" signs on the batteries to
the signs on the battery compartment.

3. Close the battery cover.

!

gent _y / ....

push /

ii

Note:

1. Dispose of your batteries in a designated disposal area. Do not throw the batteries into fire.

2. Do not mix battery types or combine used batteries with new ones.

3. Remove depleted batteries immediately to prevent battery acid from leaking into the battery compartment.

4. If you do not intend to use the remote control for a long time, remove the batteries.

5. The effective range of remote control is suggested below.

Remote control range

1. The remote control distance: 8 meters(26.2 feet) in front of the TV set.

2. The remote control angle: taking the television infrared light receiver window as an apex, 6 meters
(19.7 feet) away, its controlled angle (left to right) is within 30 degrees, while the vertical angle (up to
down)is within 30 degrees.

Remote contro! sensor

15

Remote Control Panel

@

Buttons instructions

(1) Power On/Off.
(2) Power indicator.
(3) INPUT: Switch among TV, Video, Component, HDMI and

VGA.

(4) 0-9 Numbers: For direct channel access.
(5) Last: Return to previous channel.
(6) -- : Select digital channels.
(7) PICTURE: Picture Mode selecting.
(8) SOUND: Sound Mode selecting.
(9) DISPLAY: Display current status information.
(10) MUTE: Mute the sound.
(11) VOLA IV: Volume increase/Volume decrease.
(12) CHA IV: Next channel/Previous channel.
(13) MENU: Display the main menu/Back menu display.
(14) EXIT: On screen display (OSD) menu exit.
(15) ENTER: Enter or confirm the operation/return to the previous menu.

A/_'/4/I_: Up/Down/Left/Right operation.

(16) MTS/SAP: Choose stereo, mono or Separate Audio Program

(SAP broadcast).
(17) ASPECT: Select screen mode.
(18) CCD: Closed caption decoder function.
(19) GUIDE: ATSC tuners feature the Electronic Program Guide

(EPG) function.
(20) Sleep: Set the sleep timer.
(21) TIME: Display the current timer.
(22) Electronic Program Guide(EPG) function: After pressing the

"GUIDE" button in the digital TV channel option, the 4 same color
buttons will appear with explanations in the OSD. Follow the steps
illustrated in the OSD.

(23) NOT supported in this TV. These buttons are for DVD Combo TV.

Note:The design of the remote control is subject to change and may be

different from the actual one. Those buttons without comment have no

relations with this TV.

16

Using the Remote Control

Basic Operation

Connecting power cord to the TV

1. Connect the power cord to the connector on the back of the TV, if the power cord in accessories.
Note:When connecting the power cord to the connector of the TV, make sure the power cord is fully
inserted in the place. Bad contact may cause high temperature of the connector and the risk of fire or
other damages.

2. Connect the power cord to the AC power outlet.
Power ON/OFF

1. Connect the TV to a power outlet. If the power indicator is blue, it means that the TV is STANDBY. Press

the Standby button on the front control or on the remote control to turn the TV on. Once the TV is turn on,
the power indicator will be turned off. Several seconds later, the TV picture will be displayed on
the screen.

2. Press the Standby button on the front control or on the remote control to turn the TV off temporarily.

3. Always remove the AC power plug from the outlet when not using this TV for a long period of time.

Signal source selection

Press the [INPUT] button to select TV, AV, Component, VGA and HDMI inputs. There are two

ways to select the source: One is to press the [INPUT] button continuously, while the other is to use the
ARROW and [ENTER] buttons to confirm the source.

Select channels

Please use [CHA / CHV] button on the remote panel to select channels. [CHA] indicates channel number up;
[CHV] indicates channel number down. Press [CHA / ChV] button on the side panel of the TV to select the

channels. If you want to choose any of the skipped channels, press the number directly.

Use [Mute] button
Press the [Mute] button to mute the sound. Press the [Mute] button again to resume the sound.

Select picture modes

Press the [PICTURE] button to select the picture mode from four options: Standard, Cinema, User or Vivid.

You can adjust the picture mode based upon your personal preference.

Select sound modes

Press the [AUDIO] button to select sound modes from Standard, Speech, User or Music.

Select screen modes

Press the [ASPECT] button to select from six zoom modes: Wide, Normal, Zoom, Cinema, Dot-to-Dot or Auto.

Use [GUIDE] button
Press the [GUIDE] button to display features of the ATSC program and the EPG function.

Use [DISPLAY] button
Press the [DISPLAY] button to view current source information.

17

Using the Remote Control

Use [EXIT] button
Press the [EXIT] button to exit the OSD menu.

Select channels by numbers

To select a channel: Press the channel number you would like to go to. For example, to select channel number

120, press buttons 1,2 and 0, respectively and then press [ENTER] to confirm.

Use [MENU] button
Press the [MENU] button to display the TV OSD menu.

Use [LAST] button
Press the [LAST] button to return to the previous channel.

Use [ENTER] button
Press the [ENTER] button to select a particular item.

Adjust Volume

Press [VOLA / VOLV] button to adjust the volume.

Use [CCD] button
Press the [CCD] button to change the CCD mode. Using this button will set the Closed Caption mode when

viewing a DTV or TV channel.

Note: Set the default Closed Caption setting for all channels in the Menu. For ATV the options are CC1, CC2,
CC3, CC4, TEXT1, TEXT2, TEXT3, TEXT4 or Off. For DTV, the options are from Service1 to Service6 or Off.

Use [MTS/SAP] button
Press the [MTS/SAP] button to change the sound mode (Mono, Stereo, SAP). This button will select the MTS
options of Stereo, SAP, or Mono in TV mode, alternate audio channels, and when available, in DTV mode.

Use [SLEEP] button
Press the [SLEEP] button repeatedly to set the sleep time, which can be set to: 10 Mins, 20 Mins, 30 Mins, 40

Mins, 50 Mins, 60 Mins, 90 Mins, 120 Mins or Off.

Use [TIME] button
Press the [TIME] button to display the current time.

18

Changing the TV Settings

1 Press [MENU_ button to display the main menu.

2 Press [A/V] button to select TV item.

3 Press [ _/ENTER] button to enter TV menu.

4 Press [A/T] button to select the option,

press [P-/ENTER_ button to enter or press [_/_
button to adjust the option.

5 Press the [Menu_ button to close the menu.

You can adjust:

o Tuner Mode - Select the TV signal source. You can

select Antenna or Cable.

• Channel Scan - Scans for channels that have signals

and stores the channels information in memory.

DTV: The scanned TV programmes in digital signals.

TV: The scanned programmes in analog signals.

• Channel Skip - Deletes a channel stored in memory.

When you press CHA or CHV, your TV skips the
channel you deleted. You can still tune to the channel
using the number buttons on the remote control.

, MTS - Selects the sound mode. You can select

Mono, Stereo, or SAP(Second Audio Program)

• Audio Language - Selects the audio language for a

program.
SAP (Second Audio Program) - Depending on the

particular program being broadcast, you can listen to a

foreign-language translation.

19

Changing the TV Settings

1
2
3
4

Press
Press
Press
Press

press
button

Press

[MENU] button to display the main menu.
[A/T] button to select Video item.

[ I_-/ENTER] button to enter Video menu.
[A/T] button to select the option,

[_/ENTER] button to enter or press [4/1_]

to adjust the option.

the [Menu] button to close the menu.

You can adjust:

• Picture Mode - Adjusts the Picture Mode. You can select Standard, Cinema, User or Vivid.
" Brightness - You can increase or decrease the brightness of the picture. Increasing the

brightness can add more light to dark areas of the picture, while decreasing the brightness can

add more darkness to light areas of the picture.

• Contrast - You can increase or decrease the contrast of the picture. Increase the contrast to
adjust the white areas of the picture or decrease the contrast to adjust the black areas of the

picture.

• Saturation - Adjusts the intensity of the colors.

" Sharpness - You can increase the sharpness level for clearer images or decrease the sharpness

level for smoother images.

, Color temperature - Changes the color temperature. You can select the color temperature from

three options: Cool, Standard or Warm.

, Advanced Video - Accesses advanced video settings such as DNR, Adaptive Luma Control,

Flesh Tone and MFC.

O DNR: It can optimize the picture signal from time

and space; reduce the outside noise interference and

return the pure initial signal. It has four ratings: Low,
Standard, Strong and Off.

OAdaptive Luma Control: According to the content of

picture, it can adjust brightness automatically.

OFlesh Tone: When this feature is "on" state, the TV

could be the basis of image content, for color
correction.

20

Changing the TV Settings

MFC: To improve the perception of moving images.

The weak setting is suitable for most programs and

is recommended for general viewing, normal and
strong settings can further enhance motion, however
on some cases can create a halo effect on edges of
moving objects. You may need to switch settings
pending the contents your viewing.

PROSCAN using MFC's unique motion compensation technology, which eliminates the tail and jitter

of dynamic images effectively, and makes the image edge clearer.

It reduce the dynamic screen blur which is difficult to be perceived by human eyes. Even playing

rolling subtitles, the font edge is also clear.

Effect - Removes drag from fast scenes with a lot of movement to provide a clearer picture.

If you enable MFC (Motion Flow Compensation), noise may appear on the screen.
If this occurs, set "Effect" to off.

Custom : The TV can be set to automatically sense and process film signals from all sources

and adjust the picture for optimum quality.

- Mode 1 :Adjusts the judder reduction level from video sources when playing 24Hz films.

- Mode 2 : Adjusts the blur reduction level from video sources.
Demo Partition - Press [4/1_ buttons to choose left, right or all in the screen for MFC Demo.
Demo - This is only intended for use in retail environments.

21

Changing the TV Settings

1 Press [MENU] button to display the main menu.

2 Press [A/T] button to select Audio item.
3 Press [ I_/ENTER_ button to enter Audio menu.
4 Press [A/T] button to select the option,

press [_/ENTER_ button to enter or press [4/_

button to adjust the option.

5 Press the [Menu] button to close the menu.

You can adjust:

- Balance - Adjusts the volume of the left and right
speakers.

- Surround Sound - Turns the surround sound effect
on or off.

" Equalizer - Weaken or enlarge the sound of the main

frequency points.

" SPDIF Type - Selects the SPDIF type. You can

select PCM, Dolby Digital or Off.

PCM = PCM is an encoding, mainly used for anolog signal, Dolby mainly used for digital

signal.

Dolby =when the data stream carries Dolby signal, digital SPDIF outputs Dolby data stream.

When the data stream carries no Dolby signal, it transports PCM data stream.

Auto =when the data stream carries Dolby signal, digital SPDIF outputs Dolby data

stream. When the data stream carries no Dolby signal, it transports PCM data stream.
No matter the data stream carries Dolby stream or not, it outputs PCM data stream.

" Auto Volume Control - Adjust volume according to different audio signal.

Note: Via SPDIF Type, you can choose the digital audio out type. If Auto Volume Control is

On, that means audio out control is activated.

22

Changing the TV Settings

1 Press [MENU] button to display the main menu.
2 Press [A/T] button to select Setup item.
3 Press [ I_/ENTER] button to enter Setup menu.
4 Press [A/T] button to select the option,

press [_-/ENTER_ button to enter or press [41/_

button to adjust the option.

5 Press the [Menu_ button to close the menu.

You can adjust:

. OSD Language - Use the right or left arrow button to choose the OSD Language among English,

Spanish and French.

• Screen Mode - Use the arrow button to choose the screen aspect ration from Wide, Normal,
Zoom, Cinema, Dot-to-Dot or Auto.

O Normal

The original 4:3 aspect ratio (1.33:1 signal)
is preserved, so black bars are added to the
left and right of the image. Standard TV
broadcasts are displayed with a 4:3 aspect ratio.

O Wide

When watching a standard broadcast or full-frame

movie in this mode, the display image is stretched
proportionately to fill the TV screen.

When watching a widescreen (1.78:1 signal)

program or movie, the display image fills the TV

O

Zoom
Stretches the 4:3 aspect ratio image vertically

and horizontally to fill the screen at 1:1.78
aspect ratio.

23

Changing the "IV Settings

_]_ Cinema

Stretches the 4:3 aspect ratio image vertically
and horizontally to fill the screen at 1:2,35
aspect ratio,

Dot to dot
Use the function to see the full image without any
cutoff, when HDMI (720p/1080i/1080p),
Component (1080i/1080p), DTV (1080i) or VGA
signals are inputs.

• DPMS - This is a good function for a computer monitor. When DPMS is on, the computer will
control the screen on or off. For example, if the computer is in sleep mode, the screen will be

switched off. If the computer is activated, the screen also is activated.

" Time Setup - You can set up the exact time by yourself. You can also set up Sleeper Time and

Auto Sleep Time.

24

Changing the TV Settings

• Caption: There are three items in it - Analog
Closed Caption, Digital Closed Caption and Digital
Caption Style.

This is a function about caption, display caption by
anolog signal and display caption by digital signal.
Analog Closed Caption: CCl, CC2, CC3, Cc4,

TEXT1, TEXT2, TEXT3, TEXT4.

Digital Closed Caption: Service1, Service2, Service3,

Service4, Service5, Service6.

Digital Caption Style: There are two Caption Styles.
One is the automatic function set as the broadcaster,
while the other is the custom style where you can
adjust the font size, color, opacity, background color
etc., accordingly.

• Reset Default - Every TV has its original setting
before leaving the factory. So this function helps
you restore these settings.

25

Changing the TV Settings

1 Press [MENU] button to display the main menu.
2 Press CA/T] button to select Parental item.
3 Press C IP,/ENTER] button to enter Parental menu.

4 Press CA/T] button to select the option,

press [I_/ENTER] button to enter or press [4/1_]

button to adjust the option.

5 Press the [Menu] button to close the menu.

When you first use this function, the default
password is E0000].
Once you input this password, you can: Press A,/_'
to highlight an option, then press 4/ I_ to adjust the
option. You can adjust:

. Change Password - The first time you use this

function, use the default password. If you want to
change it, first enter the new password then enter
the same password again.

" Channel Block - This function will let you block any

channel you want.

" Input Block - You can block the input source with

this function. For example, if you want to block AV

input, just highlight EAV_ and press CENTER]. The

AV input will not be seen in the screen.

" Clean All - This function will let you clean all the

channels stored on this TV.

Note: If you choose this function, all the programs

you preset will be lost.

" Program Block-

A. Rating Enable is on.

B. U.S. TV Ratings: You can choose TV

ratings according to the illustration on the screen.

C. The settings for U.S. Movie Ratings,

Canada (English) Ratings and Canada (French)

Ratings follow Step B.

If you want to block the unrated program, please

turn on this function.

26

Changing the TV Settings

Following is the description of these ratings.

Age Defined as
TV-Y All children
TV-Y7 Directed to older children

TV-G General audience

TV-PG Parental Guidance suggested
TV-14 Parents Strongly cautioned
TV-MA Mature Audience only

Contents Defined as

FV Fantasy Violence

D Suggestive dialogue

L Strong language

S Sexual situations

V Violence

Rating Defined as

G General audience

PG Parental Guidance suggested

PG-13 Parents strongly cautioned
R Restricted
NC-17 No one 17 and under admitted

X Adult audience only

27

Changing the TV Settings

About Canada (French)

Rating Description

G General

8 ans+ 8+General; Not recommended for young children
13 ans+ Programming may not be suitable for children under

the age of 13

16 ans+ Programming is not be suitable for children under

the age of 16

18 ans+ Programming restricted to adults

About Canada (English)

Rating Description

C Children
C8+ Children eight years and older
G General Programming, suitable for all audiences

PG Parents Guidance
14+ Viewers 14 years and older
18+ Adult programming

NOTE; As you block rating, all rating higher than the ones you select are blocked as well. For

example, if you choose to block the MPAA rating R, the higher ratings, NC-17 and X, are
automatically blocked too.

28

Appendix

Before calling a service technician, please check the following table for a possible cause of the problem and some

solutions.
Customer important notice: If the TV can not be operated, please unplug the power and restart.

Symptoms

TV will not turn on

No picture, no sound

No sound, picture OK

Poor sound, picture OK

Poor picture, sound OK

Unable to select a certain

channel

The

Poor colour or no colour

remote control does

not operate

Disorder display at power on

Possible Solutions

• Make sure the power cord is plugged in, then press Power (Standby).

• The remote control batteries may be dead. Replace the batteries.

= Unplug the VGA wire and plug the power wire again.

• Check if you have set the timer off.

• Check the antenna/cable connections.

= Press [Display] to see if you have selected the right signal source.
= The sound may be muted. Press [VOL+ ] on the remote control.

= The station may have broadcast difficulties. Try another channel.

• Check the speakers cable connections.

• The station may have broadcast difficulties. Try another channel

• Check the speakers cable connections.

• Check the antenna connections.
= The station may have broadcast difficulties. Try another channel.

• Adjust the picture from the menu.

= The channel may be skipped. Choose this channel by directly selecting

the buttons from the remote control.

• The station may have broadcast difficulties_ Try another channel.
= Adjust Saturation in the Video settings menu.

• There may be an obstruction between the remote control and the
remote control sensor.

= The batteries may be installed with a wrong polarity.
= The remote control batteries may be dead. Replace the batteries.

= This may be caused because of a very short interval between POWER

OFF and ON.

• Unplug the power and restart.

29

Appendix

Model 42LED55SA 47LED55SA 55LED55SA
Screen Diagonal Size 42 inches 47 inches 55 inches
Screen Resolution 1920X1080 Pixels 1920X1080 Pixels 1920X1080 Pixels
Power Consumption 165W 180W 195W

Wall-mount screws pattern M6X25mm (4 pcs) M6X25mm (4 pcs) M8X25mm (4 pcs)
Wall-mount dimension(VESA) 200mm X 200mm 200mm X 200mm 400mm X 400mm

3ize with base(inch)(L X WX HI 40.6x11.5x28.1 45x11.2x30.7 52.8x13.2x35

Weight with base(Ibs) 44.2 Ibs 56.1 Ibs 99 Ibs

Power Supply AC 60Hz 120V
Television System

Audio multiplex

Channel coverage

Sound Output Power (RMS)
Component (Y/Pb/Pr) mode
PC (VGA) mode

HDMI mode

Environmental Conditions

Supplied accessories

American TV standard NTSC / ATSC system

BTSC system
VHF: 2-13 UHF: 14-69 CATV: 1-125
Digital Terrestrial Broadcast (8VSB): 2-69
Digital Cable(64/256 QAM): 1-135
8W + 8W
4801/60Hz, 480P/60Hz, 720P/60Hz, 10801/60Hz
640X480/60Hz, 800X600/60Hz, 1024X768/60Hz
4801/60Hz, 480P/60Hz, 720P/60Hz, 10801/60Hz, 1080P/60Hz
640X480/60Hz, 800X600/60Hz, 1024X768/60Hz
Temperature 5°C~35°C (41F~95F)
Humidity : 20%-80%RH

Atmospheric pressure: 86kPa-106kPa

Remote control, Batteries, User Manual, Quick Start Guide,
Remote Control Guide, Children Safety Guide, Warranty Card,

Registration Card

Note: Design and specifications are subject to change without notice.

CUSTOMER NOTICE: Use carefully when operating to prevent damage to the screen.

3O

SRS_ restores the original three-dimensional sound field of stereo recordings
by retrieving spatial information buried in the recordings to create an
immersive 3D sound-field using only two speakers or headphones.

LBY

DIGITAL I

Manufactured under license from Dolby Laboratories.
Dolby and the double D symbol are trademarks of Dolby Laboratories.

This product contains electrical or electronic materials. The presence of these materials may, if

not disposed of properly, have potential adverse effects on the environment and human health.
Presence of this label on the product means it should not be disposed of as unsorted waste

and must be collected separately. As a consumer, you are responsible for ensuring that this

product is disposed of properly. To find out how to properly dispose of this product, please go

to www.proscanus.com and click on Sustainability.

H nllll

This TV incorporates High-Definition Multimedia Interface (HDMP) technology.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.