PROLiNK PWN3702P User Manual
MODEL NO:
PWN3702P
Quick Installation Guide
Wireless-N Extender 300Mbps
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following these guides or need further information pertaining to the device,
please visit our website at www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of shipping and may change without prior
notice, written or otherwise.
AC Passthrough
Version 1.20
(English / Indonesian)
1. Package Contents
1 2
BEFORE GETTING STARTED
This document is designed to aid you to get started with the device. If you experience problems following these guides or need further information pertaining to the device,
please visit our website at www.prolink2u.com. All specifications are subject to the manufacturer’s configuration at the time of shipping and may change without prior
notice, written or otherwise.
Items:
1
One (1) unit of PROLiNK® PWN3702P
2
One (1) piece of Quick Installation Guide (QIG)
Note:
1. The illustrations in this document may appear different from your model.
2. If any of above item is not packed in your package when open, please consult your reseller immediately.
PWN3702P
Quick Installation Guide
Wireless-N Extender 300Mbps
AC Passthrough
Version 1.10
(English / Indonesian)
MODEL NO:
EN 1
2. Overview
Back ViewFront View Left View Right View
1
WPS
2
2 3
1
AC Passthrough Socket
2
WPS : Press 1 second to trigger WPS function
3
LED Indicators:
Reset
Power : On - Power On
Off - Power Off
WLAN : On - Wireless turn On
Off - Wireless turn Off
WPS : On - WPS feature turn On
Off - WPS feature turn Off
Blinking - WPS triggering
Signal Strength : 1 LED On : Low Signal
2 LEDs On : Medium Signal
3 LEDs On : Good Signal
4 LEDs On : Excellent Signal
Note:
The illustration in this document may appear different from your model.
5
4
4
Reset : Press 1 - 5 seconds to reboot extender.
Press > 5 seconds to reset to factory default and reboot.
5
AC Power Input
Caution : If the device is used wrongly, this may lead to
personal injury and result in property damage
Instructions Included : Read installation guide carefully to
avoid misuse of the device
Caution:
• The socket outlet of this device can only be connected with information
technology equipment (I.T.E.).
• Connected equipment should not cause any hazard to the environment,
personnel, other equipment and property when left unattended.
• The socket outlet on equipment forbids to insert to other equipment of wall plug
(Direct Plug-in) or Power bar.
• The socket outlet only can insert power cord, The direction of power cord is drooping
naturally, Power Cord length needs < 2M.
• The socket-outlet shall be installed near the equipment and shall be easily accessible
• Maximum load: 12A.
EN 2
3. Hardware Installation
Smartphone Tablet
PWN3702P
Laptop
Cable / DSL Modem Router
Router WiFi Range WiFi Extender Range
EN 3
4. Connecting to the Root AP
WPS
Method 1 : With WPS button
Step 1. Plug the PWN3702P into the electrical socket and power on the electrical socket. The Power
LED on PWN3702P will illuminate. Wait until the WLAN and WPS LEDs light up.
Step 2. Press the Wi-Fi Protected Setup (WPS) button on your wireless router or root AP.
Step 3. Press the WPS button of PWN3702P for 1 second until the WPS LED starts to blink.
Note 1. The Signal Strength LEDs will illuminate to show the link quality once connected to
the root AP.
Note 2. Both buttons must be pressed within 2 minutes.
LOCATION 1
LOCATION 2
Wireless Router
PWN3702P
WPS
2 seconds
2
Minutes
Within 2 Minutes1 second
WPS
EN 4
4. Connecting to the Root AP
Method 2 : With Web Configuration
Step 1. Connect your computer to PWN3702P via wireless.
The wireless network (SSID) shall appear as “PROLiNK_xxxxxx”.
Note: The Wi-Fi Key or password can be found on the label pasted on PWN3702P.
Step 2. Open web browser and type http://192.168.123.253 in the browser’s address box. This
is the default IP address for PWN3702P.
The default user name is “admin” and password is “password”.
Step 3. Click on Quick Setup Wizard -> Start
Click <Next>, the extender will scan and find the available wireless network.
EN 5
4. Connecting to the Root AP
Select the wireless network or root AP that you want to connect to, and click on <Next>.
Tick this checkbox if you want to set the Extender SSID and password same as the root AP.
Key in the wireless password of the wireless router or root AP, and click on <Next> to
proceed.
EN 6
Loading...