Prokit's Industries SS-989 User Manual

SS-989

2 IN 1 SMD HOT AIR REWORK STATION

User’s Manual

st

1

Edition, 2012

©2012 Copyright by Prokit’s Industries Co., Ltd.

SAFETY INSTRUCTIONS

WARNING
Warnings and cautions are placed at critical points in this manual to direct
the operator's attention to significant items. They are defined as follows:

WARNING: Failure to comply with a WARNING may result in serious injury

or death.

CAUTION: Failure to comply with a CAUTION may result in injury to the

operator, or damage to the items involved. Two examples are
given below.

NOTE : A NOTE indicates a procedure or point that is important to the process

being describe.

EXAMPLE : AN EXAMPLE is given to demonstrate a particular procedure, point

or process.

_ Be sure to comply with following WARNINGS and CAUTIONS for your

safety.

WARNING

_ Be sure not to operate the unit with any combination of temperature and air

flow settings that makes the thermal protector trip (the heater lamp turns off
during use). This could damage the unit.

CAUTION
When the power is ON, the temperature of the hot air and the nozzle
ranges from 100 to 450°C (212 to 842°F). To avoid injury to personnel or
damage to items in the work area, observe the following:

_ Do not direct the hot air toward personnel or touch the metal parts near the

nozzle.
_ Do not use the product near combustible gases or flammable materials.
_ Advise those in the work area that the unit can reach very high temperatures

and should be considered potentially dangerous.
_ Turn the power OFF when no longer using the Pro’sKit SS-989 or when

leaving it unattended.
_ Before replacing parts or storing the unit, allow the unit to cool and then turn

the power OFF.

To prevent accidents and failures, be sure to take the following
precautions:

_ Do not strike the hand piece against hard surfaces or otherwise subject it to

physical shock.
_ Be sure the unit is grounded. Always connect power to a grounded receptacle.

1

_ Do not disassemble the pump.
_ Do not modify the unit.
_ Use only genuine Pro’sKit replacement parts.
_ Do not wet the unit or use the unit with wet hands.
_ Remove power cord by holding the plug – not the wires.
_ Make sure the work area is well ventilated.
_The Pro’sKit SS-989 is not intended for use by children or infirm persons

without supervision.
_ Children should be supervised to ensure that they do not play with the SS-989.

I. Packing list and name of parts

Name of Parts

Packing List

2

1. 1.SS-989 2 in 1 SMD Hot Air Rework Station

2. User’s manual

3. Soldering iron

4. Soldering iron Stand

5. Heat Gun holder

6. Air nozzle x 3

II. Features and Specifications
Features:

2 in 1 Rework Station to save the cost

Antistatic soldering iron and hot air desoldering 2 in 1 design to save the cost.

Closed Circuit Sensor Design

Closed-loop temperature control for accurate and air-flow-independent

temperature

High Power, Quick Warm Up Times

High heating power, warm up quickly, adjustable temperature and air flow for

easy surface or hole mount components QFP, SOP type IC devices rework.

Individual Function Start Save Energy

Individual function starts save energy, or share function by 2 users at the

same time, three knobs control hot air volume, hot air temperature, and

soldering iron temperature.

LED Digital Display

Digital LED displays for both rework and soldering station

Quiet in operation

Diaphragm pump with maximum capacity at 24L/min, equipment noise less

than 45dB, wind volume and temperature are adjustable, suitable for many

kinds of use

Auto Cool-Off Process

After power switch is turned off, the auto cool-off process leaves the blower

on until the nozzle is cool in order to prolong the life of heating element and to

ensure safety

ESD Safe Design

Prevent static and leakage electric to damage the PCB.

Interchangeable hot air nozzles and tips

Interchangeable hot air nozzles and tips design for different type of surface

mount components. Also applicable to most of branded nozzles and tips.

3

Specification:

Model

Input voltage

SS-989B

SS-989H

AC220V

50Hz

Fuse 3A 250V 6A 250V 5A 250V

SS-989A SS-989A7 SS-989B4 SS-989C

AC110V

60Hz

AC127V

60Hz

AC240V

50Hz

3A 250V

Total power 700W

Overall package
size (mm)

330 (L) * 275 (W) * 195 (H)

Weight 3.7 kg

SMD Rework Specifications

Power
consumption

640

Air pump Diaphragm type
Volume 24L/min (max)
Temperature of hot
air

100℃-450℃

Noise Noise < 45dB
Scale LED display
Soldering Iron Specifications
Power consumption of soldering iron 60W
Temperature range of soldering iron 200℃-480℃
Leakage voltage of soldering iron tip <0.5mV

Assembly

A. Station assembly

● Attach the Heat Gun holder

Remove the heat gun holder screw

from the side of the station; attach the

heat gun holder to the station (Fig. 1)

B. Attach the nozzle

● Loosen the nozzle mounting screw,

attach the nozzle on heat gun then screw it.

Show as the figure 2

4

AC240V

50Hz

3A 250V

Fig. 1

Fig. 2

C. Electrical Connection and Power ON

●Place the heat gun on the holder.(Fig3)

●Loosen the pump securing screw which on the bottom of control station.

(See below pictures)

●Insert the power plug into socket

●Turn on the power switch and the lamp will be lit

●Don‘t pull out the power plug instantly after turning off the power switch,

because the fan keeps operating to protect heat element. Until the fan

stops operation completely, the power plug should not be pulled out.

III. Operation instructions (SMD rework)

●Remove SMD components (such as QFP, SOP, PLCC and so on)

1. Adjust air flow and heat gun temperature to desired level

2. Slip the pick-up puller (optional part)

under the component lead. (Fig. 4) If

the width of the component does not

match the size of the pick-up, adjust

the width of the pick-up by

Fig3

Fig. 4

5