Projecta IP600, IP300, IP150, IP1000 User Manual

INTELLI-WAVE

INVERTER

12 VOLT, PURE SINE WAVE

P/No.s IP150, IP300, IP600, IP1000

IMPORTANT SAFETY INFORMATION

Please read this manual thoroughly before use and store in a safe place for future reference.

WARNINGS

• For indoor use out of weather only.

• For use with negatively earthed vehicles & systems only.

• Internally bonded for safety, battery DC negative to case & AC socket earth.

• Hazardous voltage inside – do not attempt to open, repair or use if damaged.

• Only connect 230/240V AC appliances that are in safe condition.

• This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely.

• Young children should be supervised to ensure that they do not play with the appliance.

• It is recommended that a type ‘A’ portable residual current device (RCD) be used for added output protection.

• For independent use, do not connect to buildings.

CAUTIONS

• Batteries should be mounted in a separate well-vented enclosure.

• Even though the inverter is powered from a battery, it still produces dangerous high voltage AC power and has the potential to fatally injure if incorrectly installed or used.

• Double check battery negative and positive posts before making any connection; a wrong connection (reverse polarity) will cause the fuse/s to blow and may damage the inverter.

• A small spark (arc) can occur when making the final battery connection, this is most common when the inverter has not been used for some time. This spark is caused by the inverter’s large capacitors charging quickly. To minimise this, make the last connection quickly and completely.

• Batteries can be dangerous; follow all battery manufacturer’s instructions and warnings.

• Never operate the inverter without the DC negative input connected direct to the battery and never install a fuse, circuit breaker or battery switch in the negative supply line (IP150 excepted).

FEATURES

PURE SINE WAVE OUTPUT

There are two different types of inverters, modified sine wave and pure sine wave. The difference between the two is how closely the output replicates mains power.

Logically it follows that the process used in a pure sine wave inverter is more complex than a modified sine wave inverter and subsequently more expensive. Most electric appliances operate unaffected on a modified sine wave and hence they are more common.

Pure sine wave inverters are best for use on medical equipment and sensitive electrical appliances. They allow you to watch television without static, play your favourite game on an XBox properly on a modified sine wave inverter.

FULLY ISOLATED DESIGN

Safety is paramount around 240V and in particular with inverters which is why Projecta fully electrically isolates the DC (and therefore battery posts, vehicle chassis, etc) from the 240V AC circuit.

, PlaystationTMor WiiTMand run a fluoro, all of which may not operate

DESIGNED TO AS4763

Designed in accordance with Australian Standard AS4763 (Int): 2006 – Safety of Portable Inverters.

REMOTE CONTROL DISPLAY (IP600 AND IP1000)

Control and monitor the inverter’s performance from a remote control display allowing the inverter to be mounted flush or surface mounted out of sight. Ideal for use in caravans, motor homes and boats.

BI-COLOUR L.E.D DISPLAY

THERMOSTATICALLY CONTROLLED COOLING FAN

PROTECTION

• Low input voltage

• High input voltage

• Low battery alarm

• Over temperature

• Overload

SPECIFICATIONS

P/No. IP150 IP300 IP600 IP1000

Input 12VDC Battery/Vehicle (9.75–15.5VDC)

Input Current (Max DC Amps) 15A 30A 60A 100A

No Load Current Draw 500mA 500mA 650mA 1200mA

Remote Standby Current Draw ––2mA 2mA

Output 240VAC 50Hz

Continuous Power (Watts) 150W 300W 600W 1000W

Peak Power (Watts) 300W 600W 1200W 2000W

Inverter Classification Equipotentially Bonded Inverter (EPB)

Output Waveform Pure Sine Wave

Efficiency 85–90%

Low Battery Alarm/Shutdown Alarm 10.25V, Shutdown 9.75V (±0.2V)

Cooling Fan Automatic Temperature Controlled

Thermal Shutdown 65ºC (±5ºC)

Replacement Fuse Standard Auto Blade Fuse Quantity & Size 30A 60A 110A 220A

Fuse Location Internal

Size (mm) 232 x 108 x 63 252 x 108 x 63 250 x 168 x 81 360 x 168 x 81

Weight 1.1kg 1.25kg 2.2kg 3.2kg

(1 x 30A) (2 x 30A) (2 x 40A & 1 x 30A) (4 x 40A & 2 x 30A)

REMOTE

12VDC INPUT

+–

CHASSIS GND

OFF

AC OUTPUT

VOLTS WATTS LOAD%

Pure Sine Wave

12V DC INPUT

+–

CHASSIS

GND

300W Pure Sine Wave

STATUS

OFF

AC OUTPUT

12V DC

INPUT

150W Pure Sine Wave

STATUS

OFF

AC OUTPUT

CHASSIS

GND

PRODUCT OVERVIEW

IP150 FRONT VIEW REAR VIEW

AC Output Socket

Mounting Flange

IP300 FRONT VIEW REAR VIEW

AC Output Socket

Bi-Colour Status L.E.D

On/Off Switch

Bi-Colour Status L.E.D

Fan

Cigarette Plug

DC Input Lead

Fan

Chassis Ground

Mounting Flange

On/Off Switch

IP600 & IP1000 FRONT VIEW REAR VIEW

LCD Screen

Display

Selection

Buttons

Mounting Flange

AC Output Socket

Remote

Input

On/Off Switch

Fan

12VDC Termianls

Chassis Ground

12VDC Termianls

+ 11 hidden pages