Pro-Ject Amp Box SE User Manual

INSTRUCTIONS FOR USE
Pro-Ject Amp Box SE
Dear music lover,
thank you for purchasing a PRO-JECT AUDIO amplifier. In order to achieve maximum performance and reliability you should study these instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Connectors
Trigger
IN
OUT
2x49V
Left
Right
!
Make all connections whilst the amplifier is disconnected from the power supply.
Connection to the preamplifier
The Input sockets marked Left / Right are for connecting the cables from your pre-amp or AV processor.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the
!
left channel black or white.
Connection to the speakers
The output terminals accept loudspeaker cables terminated with 4mm Banana plugs, spades connectors or naked wire.
Only connect one loudspeaker with an impedance not less than 4 Ohm per channel.
!
The red speaker terminals carry the positive signal (+), the black speaker terminals the negative signal (–). Make sure the polarity of the connection is correct at each end of the cables.
Mains power connection
The unit is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the power supply to the 2x49V socket of the amplifier before connecting the power supply to the mains.
Never use any other DC power supply other than the one supplied with the unit.
!
Remote power on
The amplifier can be switched on & off via a special connection from the Pro-Ject Pre Box SE via the 2,5mm socket marked Trigger IN.
+
A 45cm long power-on cable (polarity
) is supplied for this purpose. Longer cables are available as
accessories. The remote power-on signal can be relayed to further units via the Trigger OUT socket.
Stand-By
The pushbutton on the front panel of the unit alternately turns the power on or returns it to standby mode. The blue LED on the front panel shows that the unit is powered on.
© Audio Trade GmbH · Pro-Ject Amp Box SE · Revision 15.10.10/15.12.10
2
Technical specifications Pro-Ject Amp Box SE
Power output: 2 x 80W/125W at 8ohms/4ohms (both channels driven) Frequency response: 10Hz - 50kHz (+0dB, -3) Channel separation: > 40dB at 20kHz Noise floor: > -90dB (A weighted) THD: < 0,1% at 90W Gain: 26dB Pre in: 1 pair RCA/Phono sockets Input sensitivity: 1,5V Input impedance: 100kohms Speaker connectors: 4mm banana plugs, spades connectors or naked wire Trigger: 12V DC switching voltage Trigger in and out: 2-pole co-axial ∅ 2,5mm jack Outboard power supply: 48V/2,5A DC, suitable for your country's mains supply Power consumption: 48V/2,5A DC Dimensions W x H x D (D with sockets): 103 x 72 x 144 (163)mm Weight: 1.400g without power supply
Service
Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use. Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer.
PRO-JECT is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Audio Trade GmbH Copyright © 2009. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
© Audio Trade GmbH · Pro-Ject Amp Box SE · Revision 15.10.10/15.12.10
3
Loading...